On 32-bit/O32, pt_regs has a padding area at the beginning into which the
syscall arguments passed via the user stack are copied. 4 arguments
totalling 16 bytes are copied to offset 16 bytes into this area, however
the area is only 24 bytes long. This means the last 2 arguments overwrite
pt_regs->regs[{0,1}].

If a syscall function returns an error, handle_sys stores the original
syscall number in pt_regs->regs[0] for syscall restart. signal.c checks
whether regs[0] is non-zero, if it is it will check whether the syscall
return value is one of the ERESTART* codes to see if it must be
restarted.

Should a syscall be made that results in a non-zero value being copied
off the user stack into regs[0], and then returns a positive (non-error)
value that matches one of the ERESTART* error codes, this can be mistaken
for requiring a syscall restart.

While the possibility for this to occur has always existed, it is made
much more likely to occur by commit 46e12c07 ("MIPS: O32 / 32-bit:
Always copy 4 stack arguments."), since now every syscall will copy 4
arguments and overwrite regs[0], rather than just those with 7 or 8
arguments.

Since that commit, booting Debian under a 32-bit MIPS kernel almost
always results in a hang early in boot, due to a wait4 syscall returning
a PID that matches one of the ERESTART* codes, which then causes an
incorrect restart of the syscall.

The problem is fixed by increasing the size of the padding area so that
arguments copied off the stack will not overwrite pt_regs->regs[{0,1}].
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7454/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 6a9c001b ("MIPS: Switch ELF core dumper to use regsets.")
switched the core dumper to use regsets, however the GP regset code
simply makes a direct copy of the kernel's pt_regs, which does not
match the original core dump register layout as defined in asm/reg.h.
Furthermore, the definition of pt_regs can vary with certain Kconfig
variables, therefore the GP regset can never be relied upon to return
registers in the same layout.

Therefore, this patch changes the GP regset to match the original core
dump layout. The layout differs for 32- and 64-bit processes, so
separate implementations of the get/set functions are added for the
32- and 64-bit regsets.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7452/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Get rid of the WANT_COMPAT_REG_H test and instead define both the 32-
and 64-bit register offset definitions at the same time with
MIPS{32,64}_ prefixes, then define the existing EF_* names to the
correct definitions for the kernel's bitness.

This patch is a prerequisite of the following bug fix patch.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7451/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

task_user_regset_view() should test for TIF_32BIT_REGS in the flags of
the specified task, not of the current task.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7450/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Whenever ptrace attempts to retrieve the FPU implementation register it
accesses it through current_cpu_data, which calls smp_processor_id().
Since the code may execute with preemption enabled, this can trigger
a warning. Fix this by using boot_cpu_data to get the IR instead.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7449/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

So far BCM47XX can only detect amount of HIGHMEM. It still requires
adding (registering) and well-testing before enabling by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7396/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This reverts commit d7a887a7.

Function add_temporary_entry is needed by bcm47xx to support highmem. We
need to add a temporary entry to check for amount of RAM.
The only change made in this revert was replacing (ENTER|EXIT)_CRITICAL.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7395/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Detect more devices and register leds & buttons for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7394/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It seems that bcm47xx can handle only 128 MiB of RAM directly. There
are few devices with 256 MiB, but Broadcom's SDK uses highmem to handle
anything above 128 MiB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7101/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7100/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7113/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Since this CONFIG option will be used for both Loongson-3A/3B machines,
and not all Loongson-3 machines are produced by Lemote, we rename
CONFIG_LEMOTE_MACH3A to CONFIG_LOONGSON_MACH3X.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7190/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Loongson-3 has some specific instructions (MMI/SIMD) in coprocessor 2.
COP2 isn't independent because it share COP1 (FPU)'s registers. This
patch enable the COP2 usage so user-space programs can use the MMI/SIMD
instructions. When COP2 exception happens, we enable both COP1 (FPU)
and COP2, only in this way the fp context can be saved and restored
correctly.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7189/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Loongson-3B is a 8-cores processor. In general it looks like there are
two Loongson-3A integrated in one chip: 8 cores are separated into two
groups (two NUMA node), each node has its own local memory.

Of course there are some differences between one Loongson-3B and two
Loongson-3A. E.g., the base addresses of IPI registers of each node are
not the same; Loongson-3A use ChipConfig register to enable/disable
clock, but Loongson-3B use FreqControl register instead.

There are two revision of Loongson-3B, the first revision is called as
Loongson-3B1000, whose frequency is 1GHz and has a PRid 0x6306, the
second revision is called as Loongson-3B1500, whose frequency is 1.5GHz
and has a PRid 0x6307. Both revisions has a bug that clock cannot be
disabled at runtime, but this will be fixed in future.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7188/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Enable sys_mbind()/sys_get_mempolicy()/sys_set_mempolicy() for O32, N32,
and N64 ABIs. By the way, O32/N32 should use the compat version of
sys_migrate_pages()/sys_move_pages(), so fix that.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7186/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Multiple Loongson-3A chips can be interconnected with HT0-bus. This is
a CC-NUMA system that every chip (node) has its own local memory and
cache coherency is maintained by hardware. The 64-bit physical memory
address format is as follows:

0x-0000-YZZZ-ZZZZ-ZZZZ

The high 16 bits should be 0, which means the real physical address
supported by Loongson-3 is 48-bit. The "Y" bits is the base address of
each node, which can be also considered as the node-id. The "Z" bits is
the address offset within a node, which means every node has a 44 bits
address space.

Macros XPHYSADDR and MAX_PHYSMEM_BITS are modified unconditionally,
because many other MIPS CPUs have also extended their address spaces.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7187/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch is prepared for Multi-chip interconnection. Since each chip
has a ChipConfig register, LOONGSON_CHIPCFG should be an array.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7185/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch is prepared for Loongson's NUMA support, it offer meaningful
sysfs files such as physical_package_id, core_id, core_siblings and
thread_siblings in /sys/devices/system/cpu/cpu?/topology.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7184/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

On MIPS currently, only the soft limit of cpu count (maxcpus) has its
effect, this patch enable the hard limit (nr_cpus) as well. Processor
cores which greater than maxcpus and less than nr_cpus can be taken up
via cpu hotplug. The code is borrowed from X86.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7183/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We check that the struct vm_area_struct pointer vma is NULL and then
dereference it a few lines below. The intent was to make sure vma is
not NULL but this is not necessary since the bug pre-dates GIT history
and seem to never have caused a problem. The tlb-4k and tlb-8k versions
of local_flush_tlb_page() don't bother checking if vma is NULL, also
vma is dereferenced before being passed to local_flush_tlb_page(),
thus it is safe to remove this NULL check.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reviewed-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7264/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The dma_cache_wback_inv function performs exactly as is required here,
unless the system has coherent I/O in which case it's a no-op. Call the
underlying cache writeback functions directly, which is arguably clearer
anyway given that the code doesn't actually have anything to do with
DMA in a strict sense.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7282/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When determining the VPE ID of a CPU, make use of the cpu_vpe_id macro
which will return 0 in a non-MT kernel build. Most code is already doing
so but a couple of places weren't. Fixing this prevents a build failure
for non-MT kernels where struct cpuinfo_mips does not contain the vpe_id
field:

  arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state':
  arch/mips/kernel/pm-cps.c:153:51: error: 'struct cpuinfo_mips' has no
      member named 'vpe_id'
    vpe_cfg = &core_cfg->vpe_config[current_cpu_data.vpe_id];

  arch/mips/kernel/smp-cps.c: In function 'wait_for_sibling_halt':
  arch/mips/kernel/smp-cps.c:363:33: error: 'struct cpuinfo_mips' has no
      member named 'vpe_id'
    unsigned vpe_id = cpu_data[cpu].vpe_id;
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When used in a non-MT kernel, the cpu_vpe_id macro never made use of
its cpuinfo argument. It doesn't actually need to since it is returning
a constant 0. However not using the argument can lead to build failures
if the compiler then notices that a variable used as part of the
argument is unused. Prevent that problem by "using" the argument as far
as the compiler is concerned, whilst still returning 0 as before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7280/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The pm-cps code can run without a CPC, although will be limited to using
only the 2 wait idle states. However the code does check for CPC
presence, and in order to work optimally the CPC support is needed. So
select it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7279/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

These symbols will not be defined when CONFIG_MIPS_CPS=n, but although
the CPS_PM_POWER_GATED state will never be used in that case the
compiler doesn't have enough information to figure that out. Add checks
which evaluate to a constant false for CONFIG_MIPS_CPS=n cases in order
to help the compiler out & eliminate the symbol references.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7278/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds detection for the Microsoft MN-700 and the Asus WL500G
router. This is based on some old code from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7490/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used all
devices from the same series are sharing the same mac address. To
prevent mac address collisions we replace them with a mac address based
on the base address. To generate such addresses we take the main mac
address from et0macaddr and increase it by two for the first wifi
device and by 3 for the second one. This matches the printed mac
address on the device. The main mac address increased by one is used as
wan address by the vendor code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7489/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The reboot on the BCM47XX SoCs is done, by setting the watchdog counter
to 1 and let it trigger a reboot, when it reaches 0. Some devices with
a BCM4705/BCM4785 SoC do not reboot when the counter is set to 1 and
decreased to 0 by the hardware. It looks like it works more reliable
when we set it to 3. As far as I understand the hardware, this should
not make any difference, but I do not have access to any documentation
for this SoC.
It is still not 100% reliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7488/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7216/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This pci fixup routine calls __init functions.
In general pci fixup routine must not call __init functions,
but this pci/isa bridge device is not hotpluggable anyway.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7215/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix wrong code spotted by -Werror=array-bounds:
	arch/mips/txx9/generic/pci.c:334:23: error: array subscript is above array bounds [-Werror=array-bounds]
	  pci_write_config_byte(dev, regs[i], dat);
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7214/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes a regression caused by commit
bb6c0bd3 [MIPS: SB1: Fix excessive kernel
warnings.], that makes `-march=r5000' selected for compilation flags
rather than supposed `-march=sb1' with compilers that do not support the
ASE selection flags introduced with that change.

For example GCC 4.1.2 supports `-mips3d'/`-mno-mips3d' (and obviously
`-march=sb1'), however it does not support `-mdmx'/`-mno-mdmx'.  As a
result the whole selection of flags fails and compilation resorts to using
`-march=r5000', meant for really old compilers indeed only.

It is always best to pick the flags individually unless we are absolutely
sure a set of flags was introduced to the toolchain together (`-march=sb1'
and `-mtune=sb1' would be a good example), and this change makes it happen
for CONFIG_CPU_SB1.  Consequently the flags ultimately selected with GCC
4.1.2 are `-march=sb1 -Wa,--trap -mno-mips3d'
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Richard Sandiford <rdsandiford@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7223/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes:

{standard input}: Assembler messages:
{standard input}:145: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
{standard input}:920: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$9'
{standard input}:1797: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:1851: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:2831: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4209: Error: opcode not supported on this processor: vr5000 (mips4) `clz $7,$7'
{standard input}:4329: Error: opcode not supported on this processor: vr5000 (mips4) `clz $2,$2'
make[2]: *** [arch/mips/mm/tlbex.o] Error 1

which triggered due to a regression causing the file to be built with
`-march=r5000' rather than `-march=sb1', fixed separately.  Nevertheless
the error should not happen, the other uses of CLZ are appropriately
guarded.  This change copies the arrangement from one of those other
places.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7222/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Code in a switch statement in probe_pcache checks the CPU type twice
unnecessarily for processor implementations that have the alias removal
feature reported by the CP0 Config7.AR and Config7.IAR bits.  This change
rewrites the affected fragment avoiding the extraneous check and improving
readability.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7221/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Wire up the set_affinity call for the internal PIC if booting on
a cpu supporting it.
Affinity is kept to boot cpu as default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7323/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In preparation for applying affinity, use the irq descriptor as the
argument for (un)mask.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7317/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7322/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Since we will have the chance of accessing the registers concurrently,
protect any accesses through a spinlock.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7321/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7320/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>