- 30 May, 2020 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.8. Major changes: ath9k * allow receive of broadcast Action frames ath9k_htc * allow receive of broadcast Action frames
-
Muna Sinada authored
According to 11ax spec. draft 4.0. DCM Max Constellation Tx data field should be set to "Reserved" for an AP, therefore bit is cleared. Signed-off-by:
Muna Sinada <msinada@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1590707417-29672-1-git-send-email-msinada@codeaurora.org
-
Muna Sinada authored
The value was 3 and it's reserved value. Corrected to maintain fw defaults. Signed-off-by:
-
Douglas Anderson authored
The ath10k/qmi.h header file contains a declaration for the function ath10k_qmi_register_service_notifier(). This function doesn't exist. Remove the declaration. This patch is a no-op and was just found by code inspection. Fixes: ba94c753 ("ath10k: add QMI message handshake for wcn3990 client") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
Jouni Malinen authored
Advertise support for multicast frame registration and update the RX filter based on the recently added FIF_MCAST_ACTION to allow broadcast Action frames to be received. This is needed for Device Provisioning Protocol (DPP) use cases that use broadcast Public Action frames. Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
-
Jouni Malinen authored
Advertise support for multicast frame registration and update the RX filter based on the recently added FIF_MCAST_ACTION to allow broadcast Action frames to be received. This is needed for Device Provisioning Protocol (DPP) use cases that use broadcast Public Action frames. Signed-off-by:
-
- 29 May, 2020 34 commits
-
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Third set of iwlwifi patches intended for v5.8 * Update range request API; * Add ACPI DSM support; * Support enabling 5.2GHz bands in Indonesia via ACPI; * Bump FW API version to 56; * TX queues refactoring started; * Fix one memory leak; * Some other small fixes and clean-ups; # gpg: Signature made Fri 29 May 2020 10:38:28 AM EEST using RSA key ID 1A3CC5FA # gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>" # gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 5.8 * fixes for sparse warnings * DBDC fixes * mt7663 remain-on-channel support * mt7915 spatial reuse support * mt7915 radiotap fix * station wcid allocation fix * mt7663 powersave fix * mt7663 scan fix * mt7611n support * cleanup # gpg: Signature made Thu 28 May 2020 07:02:21 PM EEST using DSA key ID 02A76EF5 # gpg: Good signature from "Felix Fietkau <nbd@nbd.name>" # gpg: WARNING: This key is not certified with a trusted signature! # gpg: There is no indication that the signature belongs to the owner. # Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
-
Pali Rohár authored
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to inform kernel about maximum number of p2p connections and stations in AP mode. During initialization of SD8997 wifi chip kernel prints warning: mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217 This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure. It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute. Signed-off-by:
Pali Rohár <pali@kernel.org> Signed-off-by:
-
Pali Rohár authored
During initialization of SD8997 wifi chip kernel prints warnings: mwifiex_sdio mmc0:0001:1: Unknown api_id: 3 mwifiex_sdio mmc0:0001:1: Unknown api_id: 4 This patch adds support for parsing all api ids provided by SD8997 firmware. Signed-off-by:
Ganapathi Bhat <ganapathi.bhat@nxp.com> Signed-off-by:
-
Dan Carpenter authored
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from skb->data even when skb->len is less than ETH_ZLEN so it leads to a read overflow. The fix is to pad skb->data to at least ETH_ZLEN bytes. Cc: <stable@vger.kernel.org> Reported-by:
Hu Jiahui <kirin.say@gmail.com> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Double Lo authored
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue when running at high throughput. Signed-off-by:
Double Lo <double.lo@cypress.com> Signed-off-by:
Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by:
-
Wright Feng authored
This patch fixes 43455 CRC error while running throughput test with suspend/resume stress test. The continuous failure messages before system crash: brcmfmac: brcmf_sdiod_sglist_rw: CMD53 sg block read failed -84 brcmfmac: brcmf_sdio_rxglom: glom read of 25600 bytes failed: -5 brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame brcmfmac: brcmf_sdiod_sglist_rw: CMD53 sg block read failed -84 brcmfmac: brcmf_sdio_rxglom: glom read of 24576 bytes failed: -5 brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame Signed-off-by:
Wright Feng <wright.feng@cypress.com> Signed-off-by:
-
Frank Kao authored
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO. Also enable and configure F1 MesBusyCtrl. It would resolve random driver crash issue. Signed-off-by:
Frank Kao <frank.kao@cypress.com> Signed-off-by:
-
Double Lo authored
This patch fixes 4339 CRC error while running Tput test with suspend/resume test script. The continuous failure messages before system crash: brcmfmac: brcmf_sdiod_sglist_rw: CMD53 sg block read failed -84 brcmfmac: brcmf_sdio_rxglom: glom read of 25600 bytes failed: -5 brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame brcmfmac: brcmf_sdiod_sglist_rw: CMD53 sg block read failed -84 brcmfmac: brcmf_sdio_rxglom: glom read of 24576 bytes failed: -5 brcmfmac: brcmf_sdio_rxfail: abort command, terminate frame Signed-off-by:
-
Wright Feng authored
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value. Signed-off-by:
-
Dinghao Liu authored
When wlcore_fw_status() returns an error code, a pairing runtime PM usage counter decrement is needed to keep the counter balanced. It's the same for all error paths after wlcore_fw_status(). Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Chien-Hsun Liao authored
The CCK TX setting when switch channel will fix the CCK to path A only, so if the antenna is configured to path B (e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK packets can never be delivered to the air if only path B is connected with an antenna (it can possibly be transmitted through path A, but as path B is configured, the expected behavior is incorrect). This can also solve the racing issue of CCK TX setting between driver and firmware. The CCK TX setting in driver should be removed. Otherwise, the CCK TX setting would be wrong when the racing occurs. Fixes: 297bcf82 ("rtw88: add support for set/get antennas") Signed-off-by:
Chien-Hsun Liao <ben.liao@realtek.com> Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
-
Yan-Hsuan Chuang authored
For older versions of gcc, the array = {0}; will cause warnings: drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim': >> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: >> missing braces around initializer [-Wmissing-braces] s8 bb_gain[2][8] = {0}; ^ drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near initialization for 'bb_gain[0]') [-Wmissing-braces] Fixes: 5ad4d895 ("rtw88: set power trim according to efuse PG values") Reported-by:Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Ping-Ke Shih authored
Connecting to an AP with WPA2 security may fail. The IQK and the EAPOL 4-way handshake may overlap because the driver does IQK right after assoc success. For 802.11n devices, the IQK is done in the driver and it could require more than 100ms to complete. During IQK, any TX/RX events are paused. So if the EAPOL 4-way handshake started before IQK finished, then the 1/4 and 2/4 part of the handshake could be dropped. The AP will then issue deauth with reason IEEE8021X_FAILED (23). To resolve this, move IQK routine into managed TX prepare (ieee80211_ops::mgd_prepare_tx()). The callback is called before the managed frames (auth/assoc) are sent. This will make sure that the IQK is completed before the handshake starts. But don't do IQK during scanning because doing it on each channel will take too long. For 802.11ac devices, the IQK is done in firmware and it takes less time to complete. Therefore we don't see a failure during the EAPOL 4-way handshake. But it is still worth moving the IQK into ieee80211_ops::mgd_prepare_tx(). Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Coex mechanism used to make BT have higher priority and more time to transfer data when BT inquiry-page, which leads to poor WiFi performance. Should take WiFi traffic into consideration. If the WiFi is having heavy traffic, use another parameter to make sure WiFi has more chance to TX/RX, while guarantee the priority of BT for inquiry. If the WiFi isn't busy (connected or not), set proper parameter to fix originals. Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
-
Ping-Ke Shih authored
Without setting antenna control owner, the WiFi could be disconnected if the BT has traffic. Because the antenna is switched to BT side for its traffic, and the WiFi will have no chance to transfer data. Set control owner to prevent WiFi disconnect issue. Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
-
Dinghao Liu authored
When wl12xx_cmd_role_disable() returns an error code, a pairing runtime PM usage counter decrement is needed to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
When wlcore_hw_interrupt_notify() returns an error code, a pairing runtime PM usage counter decrement is needed to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
There are two error handling paths in this functon. When wlcore_tx_work_locked() returns an error code, we should decrease the runtime PM usage counter the same way as the error handling path beginning from pm_runtime_get_sync(). Signed-off-by:
-
Pascal Terjan authored
This is one of the 9 drivers redefining rfc1042_header. Signed-off-by:
Pascal Terjan <pterjan@google.com> Signed-off-by:
-
Pascal Terjan authored
This is one of the 9 drivers redefining rfc1042_header. Signed-off-by:
-
Pali Rohár authored
They are already present in linux/mmc/sdio_ids.h. Signed-off-by:
-
Larry Finger authored
Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43legacy did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43legacy will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Larry Finger authored
Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43 did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43 will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Reported-and-tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by:
-
Yan-Hsuan Chuang authored
This reverts commit 07d0f553. For rtw88 driver, the SDIO is going to be supported, so there is no need to remove the SDIO related power sequence settings. And while the power sequence parser will pass in the mask of the HCI, the SDIO part will not be used to set registers accordingly. Moreover, the power sequence table is released as a whole package, so the next time if we are going to update, the SDIO settings will be overwritten. So, revert this now. Signed-off-by:
-
Sergey Matyukevich authored
I am leaving Quantenna, so I will no longer have access to firmware and hardware. Meanwhile I plan to participate in reviewing qtnfmac patches for a while until my firmware knowledge becomes completely obsolete. Adding myself as a reviewer using my personal email address. Signed-off-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by:
Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by:
-
Rui Salvaterra authored
This gives us WPA3 support out of the box without having to manually disable hardware crypto. The driver will fall back to software crypto if the connection requires management frame protection. Suggested-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.8. Major changes: ath10k * SDIO and SNOC are not experimental anymore
-
Luca Coelho authored
Start supporting API version 56 for AX devices. Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200529092401.aabbc5b472ee.I88cb2c3d2d07e62eac3671335ff1fb80b73c5839@changeid
-
Avraham Stern authored
Range request version 10 keeps the same command size as version 9 but uses 2 reserved fields for the responder beacon interval and station id (if exists). For now, since the beacon interval of unassoc APs is unknown, use a value of 100 TUs which is a common value for many APs. While at it, remove the definition for CCMP_256 cipher, since this is not supported. Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
-
Sharon authored
When mvm is initialized we alloc aux station with aux queue. We later free the station memory when driver is stopped, but we never free the queue's memory, which casues a leak. Add a proper de-initialization of the station. Signed-off-by:
Sharon <sara.sharon@intel.com> Signed-off-by:
-
Mordechay Goodstein authored
We don't want to have txq code in the PCIe transport code, so move all the relevant elements to a new iwl_txq structure and store it in iwl_trans. spatch @ replace_pcie @ struct iwl_trans_pcie *trans_pcie; @@ ( -trans_pcie->queue_stopped +trans->txqs.queue_stopped | -trans_pcie->queue_used +trans->txqs.queue_used | -trans_pcie->txq +trans->txqs.txq | -trans_pcie->txq +trans->txqs.txq | -trans_pcie->cmd_queue +trans->txqs.cmd.q_id | -trans_pcie->cmd_fifo +trans->txqs.cmd.fifo | -trans_pcie->cmd_q_wdg_timeout +trans->txqs.cmd.wdg_timeout ) // clean all new unused variables @ depends on replace_pcie @ type T; identifier i; expression E; @@ - T i = E; ... when != i Signed-off-by:
Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by:
-
Mordechay Goodstein authored
The txq code is not directly related to the PCIe transport, so move the structures it uses to the common iwl-trans.h header. Signed-off-by:
-
