- 03 Aug, 2015 40 commits
-
-
Lu Baolu authored
commit 2d2a3167 upstream. Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed root hub. The intention of that change was to avoid touching usb core internal field, a.k.a. lpm_capable, and let usb core to set it by checking U1 and U2 exit latency values in the descriptor. Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately, root hub is a special usb device as it has no parent. Hub_port_init() will never be called for a root hub device. That means lpm_capable will by no means be set for the root hub. As the result, lpm isn't functional at all in Linux kernel. This patch add the code to check and set lpm_capable when registering a root hub device. It could be back-ported to kernels as old as v3.15, that contains the Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM."). Reported-by:
Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
commit 7d8021c9 upstream. This patch fixes a bug introduced by commit 977dcfdc ("USB: OHCI: don't lose track of EDs when a controller dies"). The commit changed ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had been called. The user-visible consequence is that the driver occasionally crashes or locks up when an URB is submitted while another URB for the same endpoint is being unlinked. This patch moves the ED state change later, to the right place. The drawback is that now we may unnecessarily execute some instructions multiple times when a controller dies. Since controllers dying is an exceptional occurrence, a little wasted time won't matter. Signed-off-by:
Heiko Przybyl <lil_tux@web.de> Tested-by:
-
Johannes Thumshirn authored
commit d23f47d4 upstream. Destroy serial_minors IDR on module exit, reclaiming the allocated memory. This was detected by the following semantic patch (written by Luis Rodriguez <mcgrof@suse.com>) <SmPL> @ defines_module_init @ declarer name module_init, module_exit; declarer name DEFINE_IDR; identifier init; @@ module_init(init); @ defines_module_exit @ identifier exit; @@ module_exit(exit); @ declares_idr depends on defines_module_init && defines_module_exit @ identifier idr; @@ DEFINE_IDR(idr); @ on_exit_calls_destroy depends on declares_idr && defines_module_exit @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... idr_destroy(&idr); ... } @ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... +idr_destroy(&idr); } </SmPL> Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Claudio Cappelli authored
commit f6d7fb37 upstream. Add device Olivetti Olicard 300 (Network Connect: MT6225) - IDs 2020:4000. T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=4000 Rev=03.00 S: Manufacturer=Network Connect S: Product=MT6225 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Signed-off-by:
Claudio Cappelli <claudio.cappelli.linux@gmail.com> Suggested-by:
Lars Melin <larsm17@gmail.com> [johan: amend commit message with devices info ] Signed-off-by:
-
Peter Sanford authored
commit f98a7aa8 upstream. Add the USB serial console device ID for Aruba Networks 7xxx series controllers which have a USB port for their serial console. Signed-off-by:
Peter Sanford <peter@sanford.io> Signed-off-by:
-
Felipe Balbi authored
commit be9d3988 upstream. Currently, we're calling musb_start() twice for DRD ports in some situations. This has been observed to cause enumeration issues after suspend/resume cycles with AM335x. In order to fix the problem, we just have to fix the check on musb_has_gadget() so that it only returns true if current mode is Host and ignore the fact that we have or not a gadget driver loaded. Fixes: ae44df2e (usb: musb: call musb_start() only once in OTG mode) Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Michal Nazarewicz authored
commit 8515bac0 upstream. Mass storage function created via configfs always reports eight LUNs to the hosts even if only one LUN has been configured. Adjust the number when the USB function is allocated based on LUNs that user has created. Tested-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 53e20f2e upstream. There was an omission in transition to devm_xxx resource handling. iounmap(udc->phy_regs) were removed, but ioremap() was left without devm_. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Fixes: 3517c31a ("usb: gadget: mv_udc: use devm_xxx for probe") Signed-off-by:
-
Rui Miguel Silva authored
commit 4088acf1 upstream. do not try to set cancel function in synchronous operations in ffs_epfile_{read,write}_iter. Acked-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by:
-
Kishon Vijay Abraham I authored
commit b4c21f0b upstream. commit f563d230 ("usb: gadget: composite: add req_match method to usb_function") accesses cdev->config even before set config is invoked causing a NULL pointer dereferencing error while running Lecroy Mass Storage Compliance test. Fix it here by accessing cdev->config only if it is non NULL. Fixes: commit f563d230 ("usb: gadget: composite: add req_match method to usb_function"). Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Thomas Hebb authored
commit 96696a9d upstream. The marvell,berlin2cd-usb-phy compatible incorrectly sets the PLL divider to BG2's value instead of BG2CD/BG2Q's. Change it to the right value. Signed-off-by:
Thomas Hebb <tommyhebb@gmail.com> Signed-off-by:
-
Stefan Wahren authored
commit 543aa486 upstream. Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer dereference. This patch avoids the oops in mxs_phy_get_vbus_status() by aborting since there is no syscon available. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Fixes: efdbd3a5 ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection") Acked-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
NeilBrown authored
commit 4724e271 upstream. The USB phy should initialize with power-off, and will be powered on by the USB system when a cable connection is detected. Having this pm_runtime_get_sync() during probe causes the phy to *always* be powered on. Removing it returns to sensible power management. Fixes: 96be39abSigned-off-by:
NeilBrown <neil@brown.name> Signed-off-by:
-
Dan Carpenter authored
commit 83ed07c5 upstream. Static checkers complain that the current condition is never true. It seems pretty likely that it's a typo and "URB" was intended instead of "USB". Fixes: 3d97ff63 ('usbdevfs: Use scatter-gather lists for large bulk transfers') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Robert Schlabbach authored
commit fb6d1f7d upstream. Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset. Dissolve the function hub_port_finish_reset() completely and divide the actions to be taken into those which need to be done after each reset attempt and those which need to be done after the full procedure is complete, and place them in the appropriate places in hub_port_reset(). Also, remove an unneeded forward declaration of hub_port_reset(). Verbose Problem Description: USB 3.0 devices may be "lost for good" during a hub port reset. This makes Linux unable to boot from USB 3.0 devices in certain constellations of host controllers and devices, because the USB device is lost during initialization, preventing the rootfs from being mounted. The underlying problem is that in the affected constellations, during the processing inside hub_port_reset(), the hub link state goes from 0 to SS.inactive after the initial reset, and back to 0 again only after the following "warm" reset. However, hub_port_finish_reset() is called after each reset attempt and sets the state the connected USB device based on the "preliminary" status of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when the following warm reset is complete and hub_port_finish_reset() is called again, its call to set the device to USB_STATE_DEFAULT is blocked by usb_set_device_state() which does not allow taking USB devices out of USB_STATE_NOTATTACHED state. Thanks to Alan Stern for guiding me to the proper solution and how to submit it. Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27Signed-off-by:
Robert Schlabbach <robert_s@gmx.net> Acked-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
Felipe Balbi authored
commit e18b7975 upstream. In case of non-Isochronous transfers, we don't want to clear DWC3_EP_BUSY flag until XferComplete event. That's because XferInProgress was only enabled so we can recycle TRBs and usb_requests quicker, but there are still other pending requests being transferred. In order to make sure we don't allow for another StartTransfer command while the HW is still processing other transfers, we must keep DWC3_EP_BUSY flag set and this what this patch does. Fixes: f3af3651 (usb: dwc3: gadget: always enable IOC on bulk/interrupt transfers) Reported-by:
sundeep subbaraya <sundeep.lkml@gmail.com> Tested-by:
-
Subbaraya Sundeep Bhatta authored
commit 76e838c9 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
Subbaraya Sundeep Bhatta <sbhatta@xilinx.com> Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by:
-
Subbaraya Sundeep Bhatta authored
commit 891b1dc0 upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by:
-
Arne Fitzenreiter authored
commit cda57b1b upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htmSigned-off-by:
Arne Fitzenreiter <arne_f@ipfire.org> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Martin K. Petersen authored
commit 9051bd39 upstream. A new Micron drive was just announced, once again recycling the first part of the model string. Add an underscore to the M510/M550 pattern to avoid picking up the new DC drive. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
David Milburn authored
commit af34d637 upstream. Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db6), data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family) SATA controller. This patch will allow the driver to limit max_sectors as before # cat /sys/block/sdb/queue/max_sectors_kb 512 I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2 before seeing corruption, but seems safer to use previous limit. Without this patch max_sectors_kb will be 32767. tj: Minor comment update. Reported-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
David Milburn <dmilburn@redhat.com> Signed-off-by:
-
Arne Fitzenreiter authored
commit 71d126fd upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by:
-
Martin K. Petersen authored
commit f3030741 upstream. Create a sysfs "trim" attribute for each ata_device that displays whether DSM TRIM is "unsupported", "unqueued", "forced_unqueued" (blacklisted) or "queued". Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Martin K. Petersen authored
commit 5d3abf8f upstream. Some devices advertise support for the READ/WRITE LOG DMA EXT commands but fail when we try to issue them. This can lead to queued TRIM being unintentionally disabled since the relevant feature flag is located in a general purpose log page. Fall back to unqueued READ LOG EXT if the DMA variant fails while reading a log page. Signed-off-by:
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Martin K. Petersen authored
commit 243918be upstream. Queued TRIM got disabled on Micron M500DC drives thanks to the "Micron_M500*" pattern we had in place to accommodate the previous generation of this drive family. Tweak the blacklist entry slightly so we only disable queued TRIM for the non-DC variants of M500 drives. Signed-off-by:
-
Peter Ujfalusi authored
commit 1cf0f448 upstream. SOC_DAPM_SINGLE("Playback AMP", ..) should not be under kcontrols. It causes kernel crash (NULL pointer) when the mixers are listed. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Peter Ujfalusi authored
commit 80ba2669 upstream. If the card is not part of any card the tas_data->codec is NULL since it is set only during snd_soc_codec_driver.probe, which is not yet called. Signed-off-by:
-
Zidan Wang authored
commit a077e81e upstream. the enum of "DAC Polarity" should be wm8960_enum[1]. Signed-off-by:
Zidan Wang <zidan.wang@freescale.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Axel Lin authored
commit ebb6ad73 upstream. VMID Control 0 BIT[2:1] is VMID Divider Enable and Select 00 = VMID disabled (for OFF mode) 01 = 2 x 50kΩ divider (for normal operation) 10 = 2 x 250kΩ divider (for low power standby) 11 = 2 x 5kΩ divider (for fast start-up) So WM8903_VMID_RES_250K should be 2 << 1, which is 4. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Axel Lin authored
commit 12c35005 upstream. WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than WM8955_PLL_CONTROL_2. Signed-off-by:
-
Axel Lin authored
commit 14ba3ec1 upstream. According to the datasheet: R10 (0Ah) VMID Impedance Control BIT 3:2 VMIDSEL DEFAULT 00 DESCRIPTION: VMID impedance selection control 00: 75kΩ output 01: 300kΩ output 10: 2.5kΩ output WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]), so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits. Signed-off-by:
-
Arnd Bergmann authored
commit 0574eab3 upstream. I tried to fix this before and submitted a working patch, but after some discussion we came up with what seemed to be a nicer solution, resulting in commit 3d4cf65e ("ASoC: omap: fix up SND_OMAP_SOC_OMAP_ABE_TWL6040 dependency"). Unfortunately, that version was incomplete, and we still get this build error: drivers/clk/clk-palmas.c:46:16: error: field 'hw' has incomplete type drivers/clk/clk-palmas.c: In function 'to_palmas_clks_info': drivers/clk/clk-palmas.c:54:74: warning: initialization from incompatible pointer type [-Winc This happens only in randconfig builds that turn on MFD_PALMAS on a platform other than OMAP2+ when COMPILE_TEST is set but COMMON_CLK is not. The new approach is only 'select COMMON_CLK_PALMAS' if we know that we are on an OMAP5 platform and MFD_PALMAS is already set. This patch has survived thousands of randconfig builds and I don't see a remaining hole in the logic. Fixes: 3d4cf65e ("ASoC: omap: fix up SND_OMAP_SOC_OMAP_ABE_TWL6040 dependency") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
-
Dan Carpenter authored
commit 474ff0ae upstream. My static checker complains that: sound/soc/fsl/imx-wm8962.c:196 imx_wm8962_probe() warn: we tested 'ret' before and it was 'false' The intent was that we use "ret" to check imx_audmux_v2_configure_port(). Fixes: 8de2ae2a ('ASoC: fsl: add imx-wm8962 machine driver') Signed-off-by:
-
Arnd Bergmann authored
commit a7310c49 upstream. Compile-tests show a warning for the newly added SND_SOC_STORM symbol: warning: (SND_SOC_STORM) selects SND_SOC_LPASS_CPU which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_QCOM) The problem is that it can be selected for COMPILE_TEST on non-QCOM builds, but the symbols it selects have a dependency. Dropping the dependencies makes it work without warnings and no other side-effects, because these are not user-visible. Signed-off-by:
-
Axel Lin authored
commit 0b51601d upstream. The M98925_DAI_WCI_MASK bit is not updated with current code. To properly set the DAI invert mode, the mask should be M98925_DAI_BCI_MASK | M98925_DAI_WCI_MASK. Signed-off-by:
-
Nicolas Boichat authored
commit 7ea3470a upstream. Prevents frequent panic on boot, if the irq handler rt5645_irq gets called before the workqueue rt5645_jack_detect_work is initialized. Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Signed-off-by:
-
Richard Fitzgerald authored
commit 15575ed5 upstream. The Arizona codec drivers had an incorrect dB scaling for the noise generator gain that started at 0dB and went upwards. Actually the highest setting is 0dB. Signed-off-by:
Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by:
-
