When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.

We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This workqueue is used by our storage target mode ULPs
via the new CQ API. Recent observations when working
with very high-end flash storage devices reveal that
UNBOUND workqueue threads can migrate between cpu cores
and even numa nodes (although some numa locality is accounted
for).

While this attribute can be useful in some workloads,
it does not fit in very nicely with the normal
run-to-completion model we usually use in our target-mode
ULPs and the block-mq irq<->cpu affinity facilities.

The whole block-mq concept is that the completion will
land on the same cpu where the submission was performed.
The fact that our submitter thread is migrating cpus
can break this locality.

We assume that as a target mode ULP, we will serve multiple
initiators/clients and we can spread the load enough without
having to use unbound kworkers.

Also, while we're at it, expose this workqueue via sysfs which
is harmless and can be useful for debug.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>

The caller might not want this overhead.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.

"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Consistently use types from linux/types.h to fix the following
rdma/mlx5-abi.h userspace compilation errors:

/usr/include/rdma/mlx5-abi.h:69:25: error: 'u64' undeclared here (not in a function)
  MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
/usr/include/rdma/mlx5-abi.h:69:29: error: expected ',' or '}' before numeric constant
  MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,

Include <linux/if_ether.h> to fix the following rdma/mlx5-abi.h
userspace compilation error:

/usr/include/rdma/mlx5-abi.h:286:12: error: 'ETH_ALEN' undeclared here (not in a function)
  __u8 dmac[ETH_ALEN];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Avoid that the following error message is reported on the console
while loading an RDMA driver with I/O MMU support enabled:

DMAR: Allocating domain for mlx5_0 failed

Ensure that DMA mapping operations that use to_pci_dev() to
access to struct pci_dev see the correct PCI device. E.g. the s390
and powerpc DMA mapping operations use to_pci_dev() even with I/O
MMU support disabled.

This patch preserves the following changes of the DMA mapping updates
patch series:
- Introduction of dma_virt_ops.
- Removal of ib_device.dma_ops.
- Removal of struct ib_dma_mapping_ops.
- Removal of an if-statement from each ib_dma_*() operation.
- IB HW drivers no longer set dma_device directly.
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Parav Pandit <parav@mellanox.com>
Fixes: commit 99db9494 ("IB/core: Remove ib_device.dma_device")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: parav@mellanox.com
Tested-by: parav@mellanox.com
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

All Soft-RoCE (rxe) is handled now in rdma-core user space library,
so the documentation. The patch below updates the documentation
link to that new location.
Reported-by: Josh Beavers <josh.beavers@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We want to return zero on success or negative error codes.  The type
should be int and not u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

"goto err;" has it's own kfree_skb() call so it's a double free.  We
only need to free on the "goto exit;" path.

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Restore device state when ethernet link changes to active.
Acked-by: George Zhang <georgezhang@vmware.com>
Acked-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Bryan Tan <bryantan@vmware.com>
Signed-off-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Moved the header page count to a macro.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Tested-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Removed the unused nreq and redundant index variables.
Moved hardcoded async and cq ring pages number to macro.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Tested-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When vmalloc_user is used to create memory that is supposed to be mmap'd
to user space, it is necessary for the mmap cookie (eg the offset) to be
aligned to SHMLBA.

This creates a situation where all virtual mappings of the same physical
page share the same virtual cache index and guarantees VIPT coherence.
Otherwise the cache is non-coherent and the kernel will not see writes
by userspace when reading the shared page (or vice-versa).
Reported-by: Josh Beavers <josh.beavers@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We need to make sure that the cq work item does not
run when we are destroying the cq. Unlike flush_work,
cancel_work_sync protects against self-requeue of the
work item (which we can do in ib_cq_poll_work).
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>--
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Netdev notification events are de-registered only when all
client iwdev instances are removed. If a single client is closed
and re-opened, netdev events could arrive even before the Control
Queue-Pair (CQP) is created, causing a NULL pointer dereference crash
in i40iw_get_cqp_request. Fix this by allowing netdev event
notification only after we have reached the INET_NOTIFIER state with
respect to device initialization.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check.  The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.

I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there.  I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.

Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more powerpc fixes from Michael Ellerman:
 "A couple of minor powerpc fixes for 4.11:

   - wire up statx() syscall

   - don't print a warning on memory hotplug when HPT resizing isn't
     available

  Thanks to: David Gibson, Chandan Rajendra"

* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Don't give a warning when HPT resizing isn't available
  powerpc: Wire up statx() syscall

Pull parisc fixes from Helge Deller:

 - Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
   modules with CONFIG_MODVERSIONS.

 - Dave Anglin optimized the cache flushing for vmap ranges.

 - Arvind Yadav provided a fix for a potential NULL pointer dereference
   in the parisc perf code (and some code cleanups).

 - I wired up the new statx system call, fixed some compiler warnings
   with the access_ok() macro and fixed shutdown code to really halt a
   system at shutdown instead of crashing & rebooting.

* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix system shutdown halt
  parisc: perf: Fix potential NULL pointer dereference
  parisc: Avoid compiler warnings with access_ok()
  parisc: Wire up statx system call
  parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
  parisc: support R_PARISC_SECREL32 relocation in modules

Pull SCSI target fixes from Nicholas Bellinger:
 "The bulk of the changes are in qla2xxx target driver code to address
  various issues found during Cavium/QLogic's internal testing (stable
  CC's included), along with a few other stability and smaller
  miscellaneous improvements.

  There are also a couple of different patch sets from Mike Christie,
  which have been a result of his work to use target-core ALUA logic
  together with tcm-user backend driver.

  Finally, a patch to address some long standing issues with
  pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
  which will make folks using physical (or virtual) magnetic tape happy"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
  qla2xxx: Update driver version to 9.00.00.00-k
  qla2xxx: Fix delayed response to command for loop mode/direct connect.
  qla2xxx: Change scsi host lookup method.
  qla2xxx: Add DebugFS node to display Port Database
  qla2xxx: Use IOCB interface to submit non-critical MBX.
  qla2xxx: Add async new target notification
  qla2xxx: Export DIF stats via debugfs
  qla2xxx: Improve T10-DIF/PI handling in driver.
  qla2xxx: Allow relogin to proceed if remote login did not finish
  qla2xxx: Fix sess_lock & hardware_lock lock order problem.
  qla2xxx: Fix inadequate lock protection for ABTS.
  qla2xxx: Fix request queue corruption.
  qla2xxx: Fix memory leak for abts processing
  qla2xxx: Allow vref count to timeout on vport delete.
  tcmu: Convert cmd_time_out into backend device attribute
  tcmu: make cmd timeout configurable
  tcmu: add helper to check if dev was configured
  target: fix race during implicit transition work flushes
  target: allow userspace to set state to transitioning
  target: fix ALUA transition timeout handling
  ...

Pull device-dax fixes from Dan Williams:
 "The device-dax driver was not being careful to handle falling back to
  smaller fault-granularity sizes.

  The driver already fails fault attempts that are smaller than the
  device's alignment, but it also needs to handle the cases where a
  larger page mapping could be established. For simplicity of the
  immediate fix the implementation just signals VM_FAULT_FALLBACK until
  fault-size == device-alignment.

  One fix is for -stable to address pmd-to-pte fallback from the
  original implementation, another fix is for the new (introduced in
  4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
  ride.

  These have received a build success notification from the kbuild
  robot"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix debug output typo
  device-dax: fix pud fault fallback handling
  device-dax: fix pmd/pte fault fallback handling

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.

Following commands are being routed through IOCB interface

- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Add routines to support T10 DIF tag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.

Use hardware_lock only for error response in this case.

Path1
       CPU0                    CPU1
       ----                    ----
  lock(&(&ha->tgt.sess_lock)->rlock);
                               lock(&(&ha->hardware_lock)->rlock);
                               lock(&(&ha->tgt.sess_lock)->rlock);
  lock(&(&ha->hardware_lock)->rlock);

Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0

Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.

In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute.  Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.

Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds.  Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.

Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull OpenRISC fixes from Stafford Horne:
 "OpenRISC fixes for build issues that were exposed by kbuild robots
  after 4.11 merge. All from allmodconfig builds. This includes:

   - bug in the handling of 8-byte get_user() calls

   - module build failure due to multile missing symbol exports"

* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
  openrisc: Export symbols needed by modules
  openrisc: fix issue handling 8 byte get_user calls
  openrisc: xchg: fix `computed is not used` warning

This fixes the following races:

1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:

if (!explicit &&
        atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
           ALUA_ACCESS_STATE_TRANSITION) {

and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.

2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.

To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.

Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>