Remove one additional line and add two new. All are reported by checkpatch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch fixes the kernel doc warnings in the driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch provides workaround in the gpio driver
for Zynq and ZynqMP Platforms by reading pin value
of EMIO banks through DATA register as it was unable
to read the value of it from DATA_RO register.
Signed-off-by: Swapna Manupati <swapnam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for suspend resume. Now that we can lose context across
a suspend/ resume cycle. Add support for the context restore.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds support for TPS68470 GPIOs.
There are 7 GPIOs and a few sensor related GPIOs.
These GPIOs can be requested and configured as
appropriate.

The GPIOs are also provided with descriptive names.
However, the typical use case is that the OS GPIO
driver will interact with TPS68470 GPIO driver
to configure these GPIOs, as requested by the
platform firmware.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently davinci_gpio_irq_setup return value is ignored. Handle the
return value appropriately.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The patch adds keystone-k2g compatible, specific properties and
an example. The patch also adds the details of supported SoCs
for each compatible.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Rapid General-Purpose Input and Output with 2 Ports (RGPIO2P)
on MX7ULP is similar to GPIO on Vibrid. But unlike Vibrid, the
RGPIO2P has an extra Port Data Direction Register (PDDR) used
to configure the individual port pins for input or output.

We introduce a bool have_paddr with fsl_gpio_soc_data data
to distinguish this differences. And we support getting the output
status by checking the GPIO direction in PDDR.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

platform_get_irq() returns an error code, but the gpio-msic driver
ignores it and always returns -EINVAL. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.

Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af

Print and propagate the return value of platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

omap_gpio_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

From the datasheet, the GPIO interface is identical to IT8728 (same
description), so just add it to the same case as the other chip.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In most of the cases, integers in this file can't be negative, so the
type can be more restricted for clarity.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix a couple of checkpatch warnings, such as complaints about bare
unsigned being used (instead of unsigned int) and missing blank lines
after declarations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Rather than manually compute the size of an array, pass the number and
element size to kcalloc().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

of_device_get_match_data() can never return NULL, therefore the check
for NULL values is unnecessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The cell count for GPIO specifiers can never be negative, so make the
field unsigned.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a section about the various parts of the GPIO subsystem to the
driver API documentation. Note that this isn't exhaustive documentation,
but rather focusses on pulling in the kerneldoc from various sources, in
order to improve coverage of kerneldoc processing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix up some references to parameters to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix up a parameter description to match the code and fix markup for a
constant to prettify output.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add missing descriptions for some parameters to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add descriptions for missing fields and fix up some parameter references
to match the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some kerneldoc has become stale or wasn't quite correct from the outset.
Fix up the most serious issues to silence warnings when building the
documentation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of using platform_get_resource() and getting the interrupts from
the resource, use platform_get_irq() which is slightly easier to use and
covers some special cases that the former doesn't.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use platform_irq_count() instead of open-coding the same code sequence.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In case of devm_clk_get failure use dev_err instead of printk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use the devm version of gpiochip_add_data and pass on the
return value. This avoids memory leak due to gpiochip_add_data
in case the driver is unbound.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This structure is only used to copy into another structure, so declare
it as const.

This issue was detected using Coccinelle and the following semantic patch:

@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };

@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct gpio_chip i = { ... };

In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:

before:
   text    data     bss     dec     hex filename
   1954     600       0    2554     9fa drivers/gpio/gpio-altera-a10sr.o

after:
   text    data     bss     dec     hex filename
   1655     512       0    2167     877 drivers/gpio/gpio-altera-a10sr.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Rapid General-Purpose Input and Output with 2 Ports (RGPIO2P)
on MX7ULP is similar to GPIO on Vibrid, except it has an extra
Port Data Direction Register (PDDR) used to configure the individual
port pins for input or output.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Errors from enable_irq_wake() in gpio_set_wake_irq() were silently ignored.
Thus led to the problem that gpio_set_wake_irq() always returned
successfully, even if enable_irq_wake() returned an error.
Signed-off-by: Philipp Rosenberger <p.rosenberger@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add fallback compatibility string for R-Car Gen 1, 2 and 3.

In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.

We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.

For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.

Also deprecate renesas,gpio-rcar as its name is more generic than its
implementation.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In header files, static inline is more commonly used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio_to_irq() API expected to be used by GPIO consumers and
not drivers and there are no guarantee that its gpiolib implementation
is irq safe.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio_to_irq() API expected to be used by GPIO consumers and
not drivers and there are no guarantee that its gpiolib implementation
is irq safe.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now IRQ mappings are always created for all (allowed) GPIOs in gpiochip in
gpiochip_irqchip_add_key() which goes against the idea of SPARSE_IRQ and,
as result, leads to:
 - increasing of memory consumption for IRQ descriptors most of which will
never ever be used (espessially on platform with a high number of GPIOs).
(sizeof(struct irq_desc) == 256 on my tested platforms)
 - imposibility to use GPIO irqchip APIs by gpio drivers when HW implements
GPIO IRQ functionality as IRQ crossbar/router which has only limited
number of IRQ outputs (example from [1], all GPIOs can be mapped on only 8
IRQs).

Hence, remove static IRQ mapping code from gpiochip_irqchip_add_key() and
instead replace irq_find_mapping() with irq_create_mapping() in
gpiochip_to_irq(). Also add additional gpiochip_irqchip_irq_valid() calls
in gpiochip_to_irq() and gpiochip_irq_map().

After this change gpio2irq mapping will happen the following way when GPIO
irqchip APIs are used by gpio driver:
 - IRQ mappings will be created statically if driver passes first_irq>0
vlaue in gpiochip_irqchip_add_key().
 - IRQ mappings will be created dynamically from gpio_to_irq() or
of_irq_get().

Tested on am335x-evm and dra72-evm-revc.
- dra72-evm-revc: number of created irq mappings decreased from 402 -> 135
  Mem savings 267*256 = 68352 (66kB)
- am335x-evm: number of created irq mappings decreased from 188 -> 63
  Mem savings 125*256 = 32000 (31kB)

[1] https://lkml.org/lkml/2017/6/15/428Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Before querying a GPIO to determine its direction, the GPIO should be
formally requested.  This allows the GPIO driver to block access to
unavailable GPIOs, which makes it easier for some drivers to support
sparse GPIO maps.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

i2c_smbus commands handle the correct byte order for smbus transactions
internally. This will currently result in incorrect operation on big
endian systems.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes:

   - compressed boot: Ignore a generated .c file

   - VDSO: Fix a register clobber list

   - DECstation: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression

   - Octeon: Fix recent cleanups that cleaned away a bit too much thus
     breaking the arch side of the EDAC and USB drivers.

   - uasm: Fix duplicate const in "const struct foo const bar[]" which
     GCC 7.1 no longer accepts.

   - Fix race on setting and getting cpu_online_mask

   - Fix preemption issue. To do so cleanly introduce macro to get the
     size of L3 cache line.

   - Revert include cleanup that sometimes results in build error

   - MicroMIPS uses bit 0 of the PC to indicate microMIPS mode. Make
     sure this bit is set for kernel entry as well.

   - Prevent configuring the kernel for both microMIPS and MT. There are
     no such CPUs currently and thus the combination is unsupported and
     results in build errors.

  This has been sitting in linux-next for a few days and has survived
  automated testing by Imagination's test farm. No known regressions
  pending except a number of issues that crept up due to lots of people
  switching to GCC 7.1"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Set ISA bit in entry-y for microMIPS kernels
  MIPS: Prevent building MT support for microMIPS kernels
  MIPS: PCI: Fix smp_processor_id() in preemptible
  MIPS: Introduce cpu_tcache_line_size
  MIPS: DEC: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression
  MIPS: VDSO: Fix clobber lists in fallback code paths
  Revert "MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>."
  MIPS: OCTEON: Fix USB platform code breakage.
  MIPS: Octeon: Fix broken EDAC driver.
  MIPS: gitignore: ignore generated .c files
  MIPS: Fix race on setting and getting cpu_online_mask
  MIPS: mm: remove duplicate "const" qualifier on insn_table