- 15 May, 2015 1 commit
-
-
K. Y. Srinivasan authored
commit 40384e4b upstream. Correctly rollback state if the failure occurs after we have handed over the ownership of the buffer to the host. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
- 04 May, 2015 39 commits
-
-
Gregory CLEMENT authored
commit 61819549 upstream. Level IRQ handlers and edge IRQ handler are managed by tow different sets of registers. But currently the driver uses the same mask for the both registers. It lead to issues with the following scenario: First, an IRQ is requested on a GPIO to be triggered on front. After, this an other IRQ is requested for a GPIO of the same bank but triggered on level. Then the first one will be also setup to be triggered on level. It leads to an interrupt storm. The different kind of handler are already associated with two different irq chip type. With this patch the driver uses a private mask for each one which solves this issue. It has been tested on an Armada XP based board and on an Armada 375 board. For the both boards, with this patch is applied, there is no such interrupt storm when running the previous scenario. This bug was already fixed but in a different way in the legacy version of this driver by Evgeniy Dushistov: 9ece8839 "ARM: orion: Fix for certain sequence of request_irq can cause irq storm". The fact the new version of the gpio drive could be affected had been discussed there: http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012Reported-by:
Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Max Filippov authored
commit 24e94454 upstream. - don't lock lp->lock in the iss_net_timer for the call of iss_net_poll, it will lock it itself; - invert order of lp->lock and opened_lock acquisition in the iss_net_open to make it consistent with iss_net_poll; - replace spin_lock with spin_lock_bh when acquiring locks used in iss_net_timer from non-atomic context; - replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit as the driver doesn't use lp->lock in the hard IRQ context; - replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise lockdep is unhappy about using non-static key. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit 01e84c70 upstream. xtensa actually uses sync_file_range2 implementation, so it should define __NR_sync_file_range2 as other architectures that use that function. That fixes userspace interface (that apparently never worked) and avoids special-casing xtensa in libc implementations. See the thread ending at http://lists.busybox.net/pipermail/uclibc/2015-February/048833.html for more details. Signed-off-by:
-
Max Filippov authored
commit 4949009e upstream. LCD driver is always built for the XTFPGA platform, but its base address is not configurable, and is wrong for ML605/KC705. Its initialization locks up KC705 board hardware. Make the whole driver optional, and its base address and bus width configurable. Implement 4-bit bus access method. Signed-off-by:
-
Lv Zheng authored
commit 2b876010 upstream. ACPICA commit aacf863cfffd46338e268b7415f7435cae93b451 It is reported that on a physically 64-bit addressed machine, 32-bit kernel can trigger crashes in accessing the memory regions that are beyond the 32-bit boundary. The region field's start address should still be 32-bit compliant, but after a calculation (adding some offsets), it may exceed the 32-bit boundary. This case is rare and buggy, but there are real BIOSes leaked with such issues (see References below). This patch fixes this gap by always defining IO addresses as 64-bit, and allows OSPMs to optimize it for a real 32-bit machine to reduce the size of the internal objects. Internal acpi_physical_address usages in the structures that can be fixed by this change include: 1. struct acpi_object_region: acpi_physical_address address; 2. struct acpi_address_range: acpi_physical_address start_address; acpi_physical_address end_address; 3. struct acpi_mem_space_context; acpi_physical_address address; 4. struct acpi_table_desc acpi_physical_address address; See known issues 1 for other usages. Note that acpi_io_address which is used for ACPI_PROCESSOR may also suffer from same problem, so this patch changes it accordingly. For iasl, it will enforce acpi_physical_address as 32-bit to generate 32-bit OSPM compatible tables on 32-bit platforms, we need to define ACPI_32BIT_PHYSICAL_ADDRESS for it in acenv.h. Known issues: 1. Cleanup of mapped virtual address In struct acpi_mem_space_context, acpi_physical_address is used as a virtual address: acpi_physical_address mapped_physical_address; It is better to introduce acpi_virtual_address or use acpi_size instead. This patch doesn't make such a change. Because this should be done along with a change to acpi_os_map_memory()/acpi_os_unmap_memory(). There should be no functional problem to leave this unchanged except that only this structure is enlarged unexpectedly. Link: https://github.com/acpica/acpica/commit/aacf863c Reference: https://bugzilla.kernel.org/show_bug.cgi?id=87971 Reference: https://bugzilla.kernel.org/show_bug.cgi?id=79501Reported-and-tested-by:
Paul Menzel <paulepanter@users.sourceforge.net> Reported-and-tested-by:
Sial Nije <sialnije@gmail.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dave Olson authored
commit f7e9e358 upstream. This problem appears to have been introduced in 2.6.29 by commit 93197a36 "Rewrite sysfs processor cache info code". This caused lscpu to error out on at least e500v2 devices, eg: error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory Some embedded powerpc systems use cache-size in DTS for the unified L2 cache size, not d-cache-size, so we need to allow for both DTS names. Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle this. Fixes: 93197a36 ("powerpc: Rewrite sysfs processor cache info code") Signed-off-by:
Dave Olson <olson@cumulusnetworks.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Alexander Ploumistos authored
commit 2eeff0b4 upstream. Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so that the device can load the ath3k firmware and re-enumerate itself as an AR3011 device. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04f2 ProdID=aff1 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Alexander Ploumistos <alexpl@fedoraproject.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Nicholas Bellinger authored
commit c8e63985 upstream. This patch fixes a bug for COMPARE_AND_WRITE handling with fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC. It adds the missing allocation for cmd->t_bidi_data_sg within transport_generic_new_cmd() that is used by COMPARE_AND_WRITE for the initial READ payload, even if the fabric is already providing a pre-allocated buffer for cmd->t_data_sg. Also, fix zero-length COMPARE_AND_WRITE handling within the compare_and_write_callback() and target_complete_ok_work() to queue the response, skipping the initial READ. This fixes COMPARE_AND_WRITE emulation with loopback, vhost, and xen-backend fabric drivers using SG_TO_MEM_NOALLOC. Reported-by:
Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
K. Y. Srinivasan authored
commit 8de58074 upstream. We may exit this function without properly freeing up the maapings we may have acquired. Fix the bug. Signed-off-by:
Long Li <longli@microsoft.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Brian Norris authored
commit 299d0c5b upstream. The comparison from the previous line seems to have been erroneously (partially) copied-and-pasted onto the next. The second line should be checking req.bytes, not req.lnum. Coverity CID #139400 Signed-off-by:
Brian Norris <computersforpeace@gmail.com> [rw: Fixed comparison] Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Brian Norris authored
commit f16db807 upstream. In some of the 'out_not_moved' error paths, lnum may be used uninitialized. Don't ignore the warning; let's fix it. This uninitialized variable doesn't have much visible effect in the end, since we just schedule the PEB for erasure, and its LEB number doesn't really matter (it just gets printed in debug messages). But let's get it straight anyway. Coverity CID #113449 Signed-off-by:
-
Brian Norris authored
commit d74adbdb upstream. If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the PEB->LEB mapping. Caught by Coverity, CID #711212. Signed-off-by:
-
Brian Norris authored
commit 8eef7d70 upstream. We are completely discarding the earlier value of 'bitflips', which could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the bitwise OR of header and data 'bitflip' statuses instead. Coverity CID #1226856 Signed-off-by:
-
Thomas D authored
commit f82263c6 upstream. Since commit ee0778a3 ("tools/power: turbostat: make Makefile a bit more capable") turbostat's Makefile is using [...] BUILD_OUTPUT := $(PWD) [...] which obviously causes trouble when building "turbostat" with make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat because GNU make does not update nor guarantee that $PWD is set. This patch changes the Makefile to use $CURDIR instead, which GNU make guarantees to set and update (i.e. when using "make -C ...") and also adds support for the O= option (see "make help" in your root of your kernel source tree for more details). Link: https://bugs.gentoo.org/show_bug.cgi?id=533918 Fixes: ee0778a3 ("tools/power: turbostat: make Makefile a bit more capable") Signed-off-by:
Thomas D. <whissi@whissi.de> Cc: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by:
Len Brown <len.brown@intel.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit c5e69192 upstream. When a event PADDING is hit (a deleted event that is still in the ring buffer), translate_data() sets the length of the padding and also updates the data pointer which is passed back to the caller. This is unneeded because the caller also updates the data pointer with the passed back length. translate_data() should not update the pointer, only set the length. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lkml.kernel.org/r/20150324135923.461431960@goodmis.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Anton Blanchard authored
commit 9a5cbce4 upstream. We cap 32bit userspace backtraces to PERF_MAX_STACK_DEPTH (currently 127), but we forgot to do the same for 64bit backtraces. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Lukas Czerner authored
commit e12fb972 upstream. Previously commit 14ece102 added a support for for syncing parent directory of newly created inodes to make sure that the inode is not lost after a power failure in no-journal mode. However this does not work in majority of cases, namely: - if the directory has inline data - if the directory is already indexed - if the directory already has at least one block and: - the new entry fits into it - or we've successfully converted it to indexed So in those cases we might lose the inode entirely even after fsync in the no-journal mode. This also includes ext2 default mode obviously. I've noticed this while running xfstest generic/321 and even though the test should fail (we need to run fsck after a crash in no-journal mode) I could not find a newly created entries even when if it was fsynced before. Fix this by adjusting the ext4_add_entry() successful exit paths to set the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the parent directory as well. Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com> Signed-off-by:
-
Arun Chandran authored
commit 1915e2ad upstream. Building a kernel with CPU_BIG_ENDIAN fails if there are stale objects from a !CPU_BIG_ENDIAN build. Due to a missing FORCE prerequisite on an if_changed rule in the VDSO Makefile, we attempt to link a stale LE object into the new BE kernel. According to Documentation/kbuild/makefiles.txt, FORCE is required for if_changed rules and forgetting it is a common mistake, so fix it by 'Forcing' the build of vdso. This patch fixes build errors like these: arch/arm64/kernel/vdso/note.o: compiled for a little endian system and target is big endian failed to merge target specific data of file arch/arm64/kernel/vdso/note.o arch/arm64/kernel/vdso/sigreturn.o: compiled for a little endian system and target is big endian failed to merge target specific data of file arch/arm64/kernel/vdso/sigreturn.o Tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Arun Chandran <achandran@mvista.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Marek Vasut authored
commit 9374e7d2 upstream. Add new ID for ASUS N10 WiFi dongle. Signed-off-by:
Marek Vasut <marex@denx.de> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Larry Finger authored
commit 2f92b314 upstream. USB ID 2001:330d is used for a D-Link DWA-131. Signed-off-by:
-
Oleg Nesterov authored
commit b72c1869 upstream. ptrace_resume() is called when the tracee is still __TASK_TRACED. We set tracee->exit_code and then wake_up_state() changes tracee->state. If the tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T) wrongly looks like another report from tracee. This confuses debugger, and since wait_task_stopped() clears ->exit_code the tracee can miss a signal. Test-case: #include <stdio.h> #include <unistd.h> #include <sys/wait.h> #include <sys/ptrace.h> #include <pthread.h> #include <assert.h> int pid; void *waiter(void *arg) { int stat; for (;;) { assert(pid == wait(&stat)); assert(WIFSTOPPED(stat)); if (WSTOPSIG(stat) == SIGHUP) continue; assert(WSTOPSIG(stat) == SIGCONT); printf("ERR! extra/wrong report:%x\n", stat); } } int main(void) { pthread_t thread; pid = fork(); if (!pid) { assert(ptrace(PTRACE_TRACEME, 0,0,0) == 0); for (;;) kill(getpid(), SIGHUP); } assert(pthread_create(&thread, NULL, waiter, NULL) == 0); for (;;) ptrace(PTRACE_CONT, pid, 0, SIGCONT); return 0; } Note for stable: the bug is very old, but without 9899d11f "ptrace: ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix should use lock_task_sighand(child). Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Reported-by:
Pavel Labath <labath@google.com> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Michael Davidson authored
commit a87938b2 upstream. With CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE enabled, and a normal top-down address allocation strategy, load_elf_binary() will attempt to map a PIE binary into an address range immediately below mm->mmap_base. Unfortunately, load_elf_ binary() does not take account of the need to allocate sufficient space for the entire binary which means that, while the first PT_LOAD segment is mapped below mm->mmap_base, the subsequent PT_LOAD segment(s) end up being mapped above mm->mmap_base into the are that is supposed to be the "gap" between the stack and the binary. Since the size of the "gap" on x86_64 is only guaranteed to be 128MB this means that binaries with large data segments > 128MB can end up mapping part of their data segment over their stack resulting in corruption of the stack (and the data segment once the binary starts to run). Any PIE binary with a data segment > 128MB is vulnerable to this although address randomization means that the actual gap between the stack and the end of the binary is normally greater than 128MB. The larger the data segment of the binary the higher the probability of failure. Fix this by calculating the total size of the binary in the same way as load_elf_interp(). Signed-off-by:
Michael Davidson <md@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Kees Cook <keescook@chromium.org> Signed-off-by:
-
Ulrik De Bie authored
commit bd884149 upstream. On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each time set_rate is done. In order to fix this, we will verify the firmware version, and if it matches the one in those laptops, the set_rate function is overloaded with a function elantech_set_rate_restore_reg_07 that performs the set_rate with the original function, followed by a restore of reg_07 (the register that sets the absolute mode on elantech v4 hardware). Also the ASUS TP500LN and X750JN firmware version, capabilities, and button constellation is added to elantech.c Reported-and-tested-by:
George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by:
Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Michael Gernoth authored
commit 91bf0c2d upstream. The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read acquire the emu_lock before accessing the FPGA. The function used to access the FPGA (snd_emu1010_fpga_read) also tries to take the emu_lock which causes a deadlock. Remove the outer locking in the proc-functions (guarding only the already safe fpga read) to prevent this deadlock. [removed superfluous flags variables too -- tiwai] Signed-off-by:
Michael Gernoth <michael@gernoth.net> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Felipe Balbi authored
commit bbc78c07 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Felipe Balbi authored
commit 74bd7b69 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit 08debfb1 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit b9e45188 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Felipe Balbi authored
commit 8c0ae657 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit 7a606ac2 upstream. While this driver was already using a 50ms resume timeout, let's make sure everybody uses the same macro so it's easy to fix later should anything go wrong. It also gives a more "stable" expectation to Linux users. Signed-off-by:
-
Felipe Balbi authored
commit 7e136bb7 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit b8fb6f79 upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit 595227db upstream. Make sure we're using the new macro, so our resume signaling will always pass certification. Signed-off-by:
-
Felipe Balbi authored
commit 62f0342d upstream. Every USB Host controller should use this new macro to define for how long resume signalling should be driven on the bus. Currently, almost every single USB controller is using a 20ms timeout for resume signalling. That's problematic for two reasons: a) sometimes that 20ms timer expires a little before 20ms, which makes us fail certification b) some (many) devices actually need more than 20ms resume signalling. Sure, in case of (b) we can state that the device is against the USB spec, but the fact is that we have no control over which device the certification lab will use. We also have no control over which host they will use. Most likely they'll be using a Windows PC which, again, we have no control over how that USB stack is written and how long resume signalling they are using. At the end of the day, we must make sure Linux passes electrical compliance when working as Host or as Device and currently we don't pass compliance as host because we're driving resume signallig for exactly 20ms and that confuses certification test setup resulting in Certification failure. Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Axel Lin authored
commit 869aee0f upstream. The res parameter passed to devm_usb_phy_match() is the location where the pointer to the usb_phy is stored, hence it needs to be dereferenced before comparing to the match data in order to find the correct match. Fixes: 410219dc ("usb: otg: utils: devres: Add API's to associate a device with the phy") Signed-off-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Sebastian Hesselbarth authored
commit a74cd13b upstream. Fix Dove's register addresses of uart2 and uart3 nodes that seem to be broken since ages due to a copy-and-paste error. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by:
-
Charles Keepax authored
commit 4e330ae4 upstream. There are two PMICs on Cragganmore, currently one dynamically assign its IRQ base and the other uses a fixed base. It is possible for the statically assigned PMIC to fail if its IRQ is taken by the dynamically assigned one. Fix this by statically assigning both the IRQ bases. Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Kukjin Kim <kgene@kernel.org> Signed-off-by:
-
Andrey Ryabinin authored
commit 8defb336 upstream. Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel split this is not so, because 2*TASK_SIZE overflows 32 bits, so the actual value of ELF_ET_DYN_BASE is: (2 * TASK_SIZE / 3) = 0x2a000000 When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address. On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000] for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled as it fails to map shadow memory. Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries has a high chance of loading somewhere in between [0x2a000000 - 0x40000000] even if ASLR enabled. This makes ASan with PIE absolutely incompatible. Fix overflow by dividing TASK_SIZE prior to multiplying. After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y): (TASK_SIZE / 3 * 2) = 0x7f555554 [1] https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerAlgorithm#MappingSigned-off-by:
Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by:
Maria Guseva <m.guseva@samsung.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Krzysztof Kozlowski authored
commit a7117f81 upstream. Driver forgot to unregister charger power supply if registering of battery supply failed in probe(). In such case the memory associated with power supply leaked. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 98a27664 ("power_supply: Add new lp8788 charger driver") Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
-
