In order to avoid synchronization races between tx and rx path, rely on
mt76_connac_skip_fw_pmctrl putting the chip in sleep mode for mt7921 and
mt7663 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In order to avoid synchronization issues between wake and ps works,
cancel ps_work in mt76_connac_pm_wake routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt7615_poll_rx rx napi callback for mt7663.
Do not access device registers in tx/rx napi if the device is not awake.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt7921_poll_rx rx napi callback for mt7921.
Do not access device registers in tx/rx napi if the device is not awake.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add the capability to define a custom rx napi callback for each driver.
This is a preliminary patch to properly support runtime-pm on rx side
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt7615_tx_worker routine as mt76 tx worker callback for
mt7663.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt7921_tx_worker routine as mt76 tx worker callback for
mt7921.
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and
increment/decrement wake counter
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce wake counter and related spinlock in order to synchronize
tx/rx path and fw_pmctrl request.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce a mutex in order to avoid a race between mt7615_mcu_lp_drv_pmctrl and
mt7615_mcu_fw_pmctrl routines since they are run two independent works

Fixes: 1f549009 ("mt76: mt7615: do not request {driver,fw}_own if already granted")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce a mutex in order to avoid a race between mt7921_mcu_drv_pmctrl and
mt7921_mcu_fw_pmctrl routines since they are run two independent works

Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Get rid of leftover mt7921_mcu_add_bss_info routine declaration
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76_connac_mcu_update_arp_filter in mt76_connac module since the
code is shared between mt7615 and mt7921
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix the following sparse warning:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:1425:70:
  warning: Using plain integer as NULL pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since driver no longer handler per-rate tx power setting, we need to
read the power values directly from registers.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Clean up the flow of per-rate txpower limit setting to get rid of
duplicate work since it has already been handled by firmware, and set
proper max_power based on different channels and regdomains.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable to limit per-rate max txpower from DT.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Scan abort should be required for the uncompleted hardware scan
interrupted by wifi reset. Otherwise, it is possible that the scan
request after wifi reset gets error code -EBUSY from mac80211 and
then blocks the reconnectting to the access point.

Fixes: 0c1ce988 ("mt76: mt7921: add wifi reset support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce chip_reset knob in mt7921 debugfs to export a way to users
able to trigger wifi reset, and group the similar operations
previously defined in chip_config in the same knob.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Wake the chip before configuring the mcu log level

Fixes: 1d8efc74 ("mt76: mt7921: introduce Runtime PM support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Dump mcu command code in hex and related prefix to help debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Get rid of init work since firmware loading is already performed in
mt7921_init_hardware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When the EEPROM data is read from flash, it can contain pre-calibration
data, which can save calibration time.

Note that group_cal can save 30% bootup calibration time, and dpd_cal can
save 75% channel switching time.
Tested-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For MT7663, the availability of the patch files is used to detect, which
corresponding firmware is going to be used (AP firmware or STA offload
firmware). If the ROM patch was already applied, it could attempt to
load the wrong firmware (without considering the alternative).
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes hardware wakeup issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>

MT7663 uses different bits for communicating reset commands/status between MCU
and host. Also add an extra initial reset command.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Dump the tx power table saved in offload firmware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce support for rate-txpower compensation for mt7663/mt7921 chipsets.
Rate-txpower limit is specified through dts
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7663 mcu relies on different APIs to configure APIs per-rate power limit
respect to mt7615 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Limits are used to update the channel max_power settings and also passed
to the firmware on channel changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Enable parsing per-rate txpower limits from DT for 11ax chipsets.
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This subnode can be used to set per-rate tx power limits either per
country code / regdomain or globally.
These limits are typically provided by the device manufacturers and are
used to limit sideband emissions and stay within regulatory limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce power-limits node in mt76 binding in order to specify
per-rate power limit values for each 802.11n/802.11ac rate
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

After DMA reset, tx status information for queued frames will never arrive.
Flush the queue to free skbs immediately instead of waiting for a timeout
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In order to avoid memory leaks, clean the dma engine unloading the
module
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

We should use ieee80211_free_txskb() to report skb status avoid wrong
aql accounting after reset.

Cc: stable@vger.kernel.org
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In mt7615_mac_reset_work(), make sure freeing skbs after mt7615_dma_reset().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7915_tx_token_put() should get call before mt76_free_pending_txwi().

Fixes: f285dfb9 ("mt76: mt7915: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7615_tx_token_put() should get call before mt76_free_pending_txwi().

Fixes: a6275e93 ("mt76: mt7615: reset token when mac_reset happens")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix ofdm rate index and ldpc setting in rate setting field of tx
descriptor.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>