The Qcom SD controller defines the usage of 0xF in data
timeout counter register (0x2E) which is actually a reserved
bit as per specification. This would result in maximum of 21.26 secs
timeout value.

Some SDcard taking more time than 2.67secs (timeout value corresponding
to 0xE) and with that observed data timeout errors.
So increasing the timeout value to max possible timeout.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-3-git-send-email-sartgarg@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Introduce max_timeout_count variable in the sdhci_host structure
and use in timeout calculation. By default its set to 0xE
(max timeout register value as per SDHC spec). But at the same time
vendors drivers can update it if they support different max timeout
register value than 0xE.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628232901-30897-2-git-send-email-sartgarg@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.

During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.

This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.

I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.

Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Print out the contents of the offending tuples when we do print them.
This can make it easier to debug, since these tuples are not exposed to
userspace anywhere else. We are limited to 64 bytes, so keep printing
out the full length in case the tuple is truncated.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-2-sean.anderson@seco.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.

Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is a spelling mistake in a pr_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210728103254.171546-1-colin.king@canonical.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Skip printing a retune error when we scan for a removed card because we
then expect a failed command.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210630041658.7574-1-wsa+renesas@sang-engineering.com
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.

This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard.  Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.

Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard.  Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

After the i.MX conversion to a DT-only platform, the mmc-esdhc-imx.h
header file is no longer used outside the driver, so move its content
to the sdhci-esdhc-imx driver and remove the header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210719193413.3792615-1-festevam@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org

When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org

When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.

Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org

This driver has had problems when handling data errors.  Add fault
injection support so that the abort handling can be easily triggered and
regression-tested.  A hrtimer is used to indicate a data CRC error at
various points during the data transfer.

Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Infinite loops are hard to read and understand because of
hidden main loop condition. Simplify such one in mmc_spi_skip().

Using schedule() to schedule (and be friendly to others)
is discouraged and cond_resched() should be used instead.
Hence, replace schedule() with cond_resched() at the same
time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210623101731.87885-1-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If we find a reset handle when probing the MMCI block,
make sure the reset is de-asserted. It could happen that
a hardware has reset asserted at boot.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Yann Gautier <yann.gautier@foss.st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210630102408.3543024-1-linus.walleij@linaro.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-4-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-3-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095734.3046-2-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add sc7280 SoC specific compatible strings for qcom-sdhci controller.
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1623835207-29462-1-git-send-email-sbhanu@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

'of_property_read_variable_u32_array' function returns number
of elements read on success. This patch updates the condition
check in the driver to overwrite the tap values from DT if exist.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-8-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Modify the data type of the clk_phase array to u32 to make it compatible
with the argument requirement of "of_property_read_variable_u32_array".

Addresses-coverity: ("incompatible_param")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-7-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The division macro DIV_ROUND_CLOSEST takes int values as the argument.
However the code here uses unsigned int values for this, which is
causing the values comparison with 0 as always true. We can use
DIV_ROUND_CLOSEST_ULL instead for the same.

Addresses-coverity: ("result_independent_of_operands")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-6-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.

Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

ZynqMP platform does not perform auto tuning in DDR50 mode. Skip the
same while the card is operating in DDR50 mode.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-4-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Arasan controller supports AUTO CMD12, this patch adds
"SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12" quirk to enable auto cmd12
feature.
By using auto cmd12 we can also avoid following error message
"Got data interrupt even though no data operation in progress"
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-3-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We have this in two places, so let's have a dedicated function. It is
also more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-4-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

I wanted to use it in a wrong way, so document the intended way.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-3-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull powerpc fixes from Michael Ellerman:

 - Fix random crashes on some 32-bit CPUs by adding isync() after
   locking/unlocking KUEP

 - Fix intermittent crashes when loading modules with strict module RWX

 - Fix a section mismatch introduce by a previous fix.

Thanks to Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo
Opsfelder Araújo, Nathan Chancellor, and Stan Johnson.

h# -----BEGIN PGP SIGNATURE-----

* tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Fix set_memory_*() against concurrent accesses
  powerpc/32s: Fix random crashes by adding isync() after locking/unlocking KUEP
  powerpc/xive: Do not mark xive_request_ipi() as __init

Pull clk driver fixes from Stephen Boyd:

 - Make the regulator state match the GDSC power domain state at boot on
   Qualcomm SoCs so that the regulator isn't turned off inadvertently.

 - Fix earlycon on i.MX6Q SoCs

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: gdsc: Ensure regulator init state matches GDSC state
  clk: imx6q: fix uart earlycon unwork

Pull char/misc driver fixes from Greg KH:
 "Here are some small driver fixes for 5.14-rc7.

  They consist of:

   - revert for an interconnect patch that was found to have problems

   - ipack tpci200 driver fixes for reported problems

   - slimbus messaging and ngd fixes for reported problems

  All are small and have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ipack: tpci200: fix memory leak in the tpci200_register
  ipack: tpci200: fix many double free issues in tpci200_pci_probe
  slimbus: ngd: reset dma setup during runtime pm
  slimbus: ngd: set correct device for pm
  slimbus: messaging: check for valid transaction id
  slimbus: messaging: start transaction ids from 1 instead of zero
  Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"

Pull USB fix from Greg KH:
 "Here is a single USB typec tcpm fix for a reported problem for
  5.14-rc7. It showed up in 5.13 and resolves an issue that Hans found.
  It has been in linux-next this week with no reported problems"

* tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: tcpm: Fix VDMs sometimes not being forwarded to alt-mode drivers

Pull RISC-V fixes from Palmer Dabbelt:

 - fix the sifive-l2-cache device tree bindings for json-schema
   compatibility. This does not change the intended behavior of the
   binding.

 - avoid improperly freeing necessary resources during early boot.

* tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fix a number of free'd resources in init_resources()
  dt-bindings: sifive-l2-cache: Fix 'select' matching

Pull s390 fix from Vasily Gorbik:

 - fix use after free of zpci_dev in pci code

* tag 's390-5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pci: fix use after free of zpci_dev

Pull mandatory file locking deprecation warning from Jeff Layton:
 "As discussed on the list, this patch just adds a new warning for folks
  who still have mandatory locking enabled and actually mount with '-o
  mand'. I'd like to get this in for v5.14 so we can push this out into
  stable kernels and hopefully reach folks who have mounts with -o mand.

  For now, I'm operating under the assumption that we'll fully remove
  this support in v5.15, but we can move that out if any legitimate
  users of this facility speak up between now and then"

* tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
  fs: warn about impending deprecation of mandatory locks

Pull block fixes from Jens Axboe:
 "Three fixes from Ming Lei that should go into 5.14:

   - Fix for a kernel panic when iterating over tags for some cases
     where a flush request is present, a regression in this cycle.

   - Request timeout fix

   - Fix flush request checking"

* tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
  blk-mq: fix is_flush_rq
  blk-mq: fix kernel panic during iterating over flush request
  blk-mq: don't grab rq's refcount in blk_mq_check_expired()

Pull io_uring fixes from Jens Axboe:
 "A few small fixes that should go into this release:

   - Fix never re-assigning an initial error value for io_uring_enter()
     for SQPOLL, if asked to do nothing

   - Fix xa_alloc_cycle() return value checking, for cases where we have
     wrapped around

   - Fix for a ctx pin issue introduced in this cycle (Pavel)"

* tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
  io_uring: fix xa_alloc_cycle() error return value check
  io_uring: pin ctx on fallback execution
  io_uring: only assign io_uring_enter() SQPOLL error in actual error case

We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.

Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>

We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.

Cc: stable@vger.kernel.org
Fixes: 61cf9370 ("io_uring: Convert personality_idr to XArray")
Signed-off-by: Jens Axboe <axboe@kernel.dk>