- 14 Apr, 2013 40 commits
-
-
Hans Verkuil authored
This prepares the driver for priority and control event handling. This patch also checks for correct streaming ownership and it makes a small improvement to the encoder_cmd ioctls: always zero 'flags' and drop the memset of 'raw' as that is already done by the v4l2 core. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
These formats are supported by the HDPVR, but they were missing in the list. Note that these formats are different from the common PAL/NTSC/SECAM formats since all color channels are transmitted separately and so there is no PAL or NTSC or SECAM color encoding involved. Signed-off-by:
-
Hans Verkuil authored
This was set to 1 << 0 which is the same as V4L2_DV_FL_REDUCED_BLANKING. It should be 1 << 3 instead. Luckily interlaced formats are rarely used, which is why this bug wasn't seen until now. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Eduardo Valentin <edubezval@gmail.com> Tested-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
- check for invalid modulators. - clamp frequency to valid range. Signed-off-by:
-
Hans Verkuil authored
Simplify locking by using the V4L2 core lock mechanism. This allows us to remove all locking from the i2c module. This will also simplify the upcoming conversion to the control framework. Signed-off-by:
-
Hans Verkuil authored
Set bus_info and fill in device_caps. Signed-off-by:
-
Hans Verkuil authored
Also set the v4l2_dev pointer in struct video_device as this was missing. Signed-off-by:
-
Hans Verkuil authored
The audout ioctls are not appropriate for radio transmitters, they apply to video output devices only. Remove them from this driver. Signed-off-by:
-
Hans Verkuil authored
dvb->adapter.priv should also be set to the i2c bus since that's what em28xx_tuner_callback expects. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Hans Verkuil authored
Increase the size of the 'reserved' array to give more room for future extensions. Signed-off-by:
-
Hans Verkuil authored
This ioctl will be extended to return more information than just the name. Signed-off-by:
-
Hans Verkuil authored
That way drivers do not need to fill in the name themselves for bridge address 0. Signed-off-by:
-
Hans Verkuil authored
After using the new VIDIOC_DBG_G_CHIP_NAME ioctl I realized that the matching by name possibility is useless. Just drop it and rename MATCH_SUBDEV_IDX to just MATCH_SUBDEV. The v4l2-dbg utility is much better placed to match by name by just enumerating all bridge and subdev devices until chip_name.name matches. Signed-off-by:
-
Hans Verkuil authored
Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This prevents abuse from both userspace and kernelspace (some bridge drivers abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this ioctl). Signed-off-by:
-
Hans Verkuil authored
The get_rf_strength op in tuner-simple is valid only for the radio mode. But due to the way get_signal in analog_demod_ops was designed it would overwrite the signal value with a bogus value when in TV mode. Pass a pointer to the signal value instead, and when not in radio mode leave it alone in the tuner-simple. This broke in commit 030755bd (tuner-core: call has_signal for both TV and radio) in kernel 3.6. Before that this was working correctly. That commit did the right thing, but what wasn't realized at the time was that tuner-simple should have been updated as well to restrict setting the signal strength to the radio mode only. Signed-off-by:
-
Hans Verkuil authored
The get_afc op in tda9887 is valid only for the radio mode. But due to the way get_afc in analog_demod_ops was designed it would overwrite the afc value with a bogus value when in TV mode. Pass a pointer to the afc value instead, and when not in radio mode leave it alone in the tda9887. This broke a long time ago in 2.6.19 when the get_afc op was introduced. Before that the afc was only set for radio mode in the tda9887. Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: clear reserved space of VBI structure to make sure no garbage is left there Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: remove empty g_parm function Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: remove empty g_audio and s_audio functions and don't set audioset in enum_input Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: return real frequency range in g_tuner and fail in s_tuner for non-zero tuner Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: don't cache frequency in s_frequency/g_frequency but return real one instead Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: remove broken priority handling and use v4l2_fh instead Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: filter audio modes that came from tuner - keep only MONO/STEREO in radio mode Signed-off-by:
-
Ondrej Zary authored
Make saa7134 driver more V4L2 compliant: implement V4L2_CAP_DEVICE_CAPS support and fix all capabilities problems reported by v4l2-compliance. Signed-off-by:
-
Laurent Pinchart authored
Configure the device external clock using the common clock framework instead of a board code callback function. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Laurent Pinchart authored
Enable the regulators when powering the sensor up, and disable them when powering it down. The regulators are mandatory. Boards that don't allow controlling the sensor power lines must provide fixed voltage regulators. Signed-off-by:
-
Laurent Pinchart authored
Replace kzalloc and gpio_request_one by their managed equivalents. Signed-off-by:
-
Laurent Pinchart authored
Replace hardcoded values with #define's. Signed-off-by:
-
Laurent Pinchart authored
The MT9M032 PLL was assumed to be identical to the MT9P031 PLL but differs significantly. Update the registers definitions and PLL limits according to the datasheet. Signed-off-by:
-
Sylwester Nawrocki authored
Make sure the debug level is properly set initially so any debug information is not printed to the kernel log without explicitly enabling it. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
There is no need to check same bit before setting it, since we always end up with a bit set. Remove some of the tests and make set unconditional, in every place where all that needs to be done is just setting a bit. Signed-off-by:
-
Sylwester Nawrocki authored
More appropriate names for the ISP chain data structure. Signed-off-by:
-
Sylwester Nawrocki authored
Instead of incrementing p_region_num field each time we set a bit in the parameter mask calculate the number of bits set only when this information is needed. Signed-off-by:
-
Sylwester Nawrocki authored
Make the sensor subdevs host_data hold a pointer to struct fimc_source_info, which is defined in the driver's public header, rather than a pointer to struct fimc_sensor_info which is specific to exynos4-is media device driver. The purpose of this change is to allow easier reuse of the fimc-lite module in the exynos5-is driver, which should similarly store a pointer to struct fimc_source_info instance in the sensor's subdev host_data. Signed-off-by:
-
Sylwester Nawrocki authored
Get the sensor subdev by walking media graph in both cases: when the device is used as a subdev only and through video node. This allows to not dereference the pipeline->subdevs[] array and makes the module more generic and easier to re-use in other media driver. Signed-off-by:
-
Sylwester Nawrocki authored
Move the sub-device group ID definitions to the driver's public header so they are available to other media drivers that need to share modules found in exynos4-is. Signed-off-by:
-
Sylwester Nawrocki authored
Make sure mem_info[] array is not used uninitialized. This prevents following compiler warning: drivers/media/platform/s5p-mfc/s5p_mfc.c: In function s5p_mfc_probe: drivers/media/platform/s5p-mfc/s5p_mfc.c:1032:33: warning: mem_info[0] may be used uninitialized in this function [-Wuninitialized] drivers/media/platform/s5p-mfc/s5p_mfc.c:1021:15: note: mem_info[0] was declared here drivers/media/platform/s5p-mfc/s5p_mfc.c:1032:33: warning: mem_info[1] may be used uninitialized in this function [-Wuninitialized] drivers/media/platform/s5p-mfc/s5p_mfc.c:1021:15: note: mem_info[1] was declared here Signed-off-by:
-
