- 22 Jul, 2020 5 commits
-
-
Zhao Heming authored
update_array_info misses calling module_put when removing cluster bitmap. steps to reproduce: ``` node1 # mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb mdadm: array /dev/md0 started. node1 # lsmod | egrep "dlm|md_|raid1" md_cluster 28672 1 dlm 212992 14 md_cluster configfs 57344 2 dlm raid1 53248 1 md_mod 176128 2 raid1,md_cluster node1 # mdadm -G /dev/md0 -b none node1 # lsmod | egrep "dlm|md_|raid1" md_cluster 28672 1 <== should be zero dlm 212992 9 md_cluster configfs 57344 2 dlm raid1 53248 1 md_mod 176128 2 raid1,md_cluster node1 # mdadm -G /dev/md0 -b clustered node1 # lsmod | egrep "dlm|md_|raid1" md_cluster 28672 2 <== increase dlm 212992 14 md_cluster configfs 57344 2 dlm raid1 53248 1 md_mod 176128 2 raid1,md_cluster node1 # mdadm -G /dev/md0 -b none node1 # mdadm -G /dev/md0 -b clustered node1 # lsmod | egrep "dlm|md_|raid1" md_cluster 28672 3 <== increase dlm 212992 14 md_cluster configfs 57344 2 dlm raid1 53248 1 md_mod 176128 2 raid1,md_cluster ``` Reviewed-by:
NeilBrown <neilb@suse.de> Signed-off-by:
Zhao Heming <heming.zhao@suse.com> Signed-off-by:
Song Liu <songliubraving@fb.com>
-
Zhao Heming authored
When array convert to clustered bitmap, the safe_mode_delay doesn't clean and vice versa. the /sys/block/mdX/md/safe_mode_delay keep original value after changing bitmap type. In safe_delay_store(), the code forbids setting mddev->safemode_delay when array is clustered. So in cluster-md env, the expected safemode_delay value should be 0. Reproducible steps: ``` node1 # mdadm --zero-superblock /dev/sd{b,c,d} node1 # mdadm -C /dev/md0 -b internal -e 1.2 -n 2 -l mirror /dev/sdb /dev/sdc node1 # cat /sys/block/md0/md/safe_mode_delay 0.204 node1 # mdadm -G /dev/md0 -b none node1 # mdadm --grow /dev/md0 --bitmap=clustered node1 # cat /sys/block/md0/md/safe_mode_delay 0.204 <== doesn't change, should ZERO for cluster-md node1 # mdadm --zero-superblock /dev/sd{b,c,d} node1 # mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sdb /dev/sdc node1 # cat /sys/block/md0/md/safe_mode_delay 0.000 node1 # mdadm -G /dev/md0 -b none node1 # cat /sys/block/md0/md/safe_mode_delay 0.000 <== doesn't change, should default value ``` Reviewed-by: -
Yufen Yu authored
Adding a new 'stripe_size' sysfs entry to set and show stripe_size. stripe_size should not be bigger than PAGE_SIZE, and it requires to be multiple of 4096. We can adjust stripe_size by writing value into sysfs entry, likely, set stripe_size as 16KB: echo 16384 > /sys/block/md1/md/stripe_size Show current stripe_size value: cat /sys/block/md1/md/stripe_size For PAGE_SIZE is equal to 4096, 'stripe_size' can just be read. Signed-off-by:Yufen Yu <yuyufen@huawei.com> Signed-off-by:
-
Yufen Yu authored
In RAID5, if issued bio size is bigger than stripe_size, it will be split in the unit of stripe_size and process them one by one. Even for size less then stripe_size, RAID5 also request data from disk at least of stripe_size. Nowdays, stripe_size is equal to the value of PAGE_SIZE. Since filesystem usually issue bio in the unit of 4KB, there is no problem for PAGE_SIZE as 4KB. But, for 64KB PAGE_SIZE, bio from filesystem requests 4KB data while RAID5 issue IO at least stripe_size (64KB) each time. That will waste resource of disk bandwidth and compute xor. To avoding the waste, we want to make stripe_size configurable. This patch just set default stripe_size as 4096. User can also set the value bigger than 4KB for some special requirements, such as we know the issued io size is more than 4KB. To evaluate the new feature, we create raid5 device '/dev/md5' with 4 SSD disk and test it on arm64 machine with 64KB PAGE_SIZE. 1) We format /dev/md5 with mkfs.ext4 and mount ext4 with default configure on /mnt directory. Then, trying to test it by dbench with command: dbench -D /mnt -t 1000 10. Result show as: 'stripe_size = 64KB' Operation Count AvgLat MaxLat ---------------------------------------- NTCreateX 9805011 0.021 64.728 Close 7202525 0.001 0.120 Rename 415213 0.051 44.681 Unlink 1980066 0.079 93.147 Deltree 240 1.793 6.516 Mkdir 120 0.004 0.007 Qpathinfo 8887512 0.007 37.114 Qfileinfo 1557262 0.001 0.030 Qfsinfo 1629582 0.012 0.152 Sfileinfo 798756 0.040 57.641 Find 3436004 0.019 57.782 WriteX 4887239 0.021 57.638 ReadX 15370483 0.005 37.818 LockX 31934 0.003 0.022 UnlockX 31933 0.001 0.021 Flush 687205 13.302 530.088 Throughput 307.799 MB/sec 10 clients 10 procs max_latency=530.091 ms ------------------------------------------------------- 'stripe_size = 4KB' Operation Count AvgLat MaxLat ---------------------------------------- NTCreateX 11999166 0.021 36.380 Close 8814128 0.001 0.122 Rename 508113 0.051 29.169 Unlink 2423242 0.070 38.141 Deltree 300 1.885 7.155 Mkdir 150 0.004 0.006 Qpathinfo 10875921 0.007 35.485 Qfileinfo 1905837 0.001 0.032 Qfsinfo 1994304 0.012 0.125 Sfileinfo 977450 0.029 26.489 Find 4204952 0.019 9.361 WriteX 5981890 0.019 27.804 ReadX 18809742 0.004 33.491 LockX 39074 0.003 0.025 UnlockX 39074 0.001 0.014 Flush 841022 10.712 458.848 Throughput 376.777 MB/sec 10 clients 10 procs max_latency=458.852 ms ------------------------------------------------------- It show that setting stripe_size as 4KB has higher thoughput, i.e. (376.777 vs 307.799) and has smaller latency than that setting as 64KB. 2) We try to evaluate IO throughput for /dev/md5 by fio with config: [4KB randwrite] direct=1 numjob=2 iodepth=64 ioengine=libaio filename=/dev/md5 bs=4KB rw=randwrite [64KB write] direct=1 numjob=2 iodepth=64 ioengine=libaio filename=/dev/md5 bs=1MB rw=write The result as follow: + + | stripe_size(64KB) | stripe_size(4KB) +----------------------------------------------------+ 4KB randwrite | 15MB/s | 100MB/s +----------------------------------------------------+ 1MB write | 1000MB/s | 700MB/s The result show that when size of io is bigger than 4KB (64KB), 64KB stripe_size has much higher IOPS. But for 4KB randwrite, that means, size of io issued to device are smaller, 4KB stripe_size have better performance. Normally, default value (4096) can get relatively good performance. But if each issued io is bigger than 4096, setting value more than 4096 may get better performance. Here, we just set default stripe_size as 4096, and we will try to support setting different stripe_size by sysfs interface in the following patch. Signed-off-by: -
Yufen Yu authored
Convert macro STRIPE_SIZE, STRIPE_SECTORS and STRIPE_SHIFT to RAID5_STRIPE_SIZE(), RAID5_STRIPE_SECTORS() and RAID5_STRIPE_SHIFT(). This patch is prepare for the following adjustable stripe_size. It will not change any existing functionality. Signed-off-by:
-
- 16 Jul, 2020 7 commits
-
-
Guoqing Jiang authored
We can't guarntee the batched stripe to be set with STRIPE_HANDLE since there are lots of functions could set the flag, such as sync_request, ops_complete_* and end_{read,write}_request etc. Also clear_batch_ready called in handle_stripe ensures the batched list can't continue to be handled by handle_stripe. Signed-off-by:Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by:
-
Guoqing Jiang authored
To make people understand the function well, let's put the comment to the right place. Signed-off-by:
-
Guoqing Jiang authored
We tried to only put the head sh of batch list to handle_list, then the handle_stripe doesn't handle other members in the batch list. However, we still got the calltrace in break_stripe_batch_list. [593764.644269] stripe state: 2003 kernel: [593764.644299] ------------[ cut here ]------------ kernel: [593764.644308] WARNING: CPU: 12 PID: 856 at drivers/md/raid5.c:4625 break_stripe_batch_list+0x203/0x240 [raid456] [...] kernel: [593764.644363] Call Trace: kernel: [593764.644370] handle_stripe+0x907/0x20c0 [raid456] kernel: [593764.644376] ? __wake_up_common_lock+0x89/0xc0 kernel: [593764.644379] handle_active_stripes.isra.57+0x35f/0x570 [raid456] kernel: [593764.644382] ? raid5_wakeup_stripe_thread+0x96/0x1f0 [raid456] kernel: [593764.644385] raid5d+0x480/0x6a0 [raid456] kernel: [593764.644390] ? md_thread+0x11f/0x160 kernel: [593764.644392] md_thread+0x11f/0x160 kernel: [593764.644394] ? wait_woken+0x80/0x80 kernel: [593764.644396] kthread+0xfc/0x130 kernel: [593764.644398] ? find_pers+0x70/0x70 kernel: [593764.644399] ? kthread_create_on_node+0x70/0x70 kernel: [593764.644401] ret_from_fork+0x1f/0x30 As we can see, the stripe was set with STRIPE_ACTIVE and STRIPE_HANDLE, and only handle_stripe could set those flags then return. And since the stipe was already in the batch list, we need to return earlier before set the two flags. And after dig a little about git history especially commit 3664847d ("md/raid5: fix a race condition in stripe batch"), it seems the batched stipe still could be handled by handle_stipe, then handle_stipe needs to return earlier if clear_batch_ready to return true. Signed-off-by:
-
Damien Le Moal authored
Remove the if statement around the call to sysfs_link_rdev() in raid10_start_reshape() to avoid the compilation warning: warning: suggest braces around empty body in an ‘if’ statement when compiling with W=1. Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
Damien Le Moal authored
Remove the if statement around the calls to sysfs_link_rdev() to avoid the compilation warning "suggest braces around empty body in an ‘if’ statement" when compiling with W=1. Also fix function description comments to avoid kdoc format warnings. Signed-off-by:
-
Damien Le Moal authored
Remove the variable offset in r5c_tree_index() to avoid a "set but not used" compilation warning when compiling with W=1. Signed-off-by:
-
Damien Le Moal authored
Remove the if statement around the calls to sysfs_link_rdev() to avoid the compilation warnings: warning: suggest braces around empty body in an ‘if’ statement when compiling with W=1. For the call to sysfs_create_link() generating the same warning, use the err variable to store the function result, avoiding triggering another warning as the function is declared as 'warn_unused_result'. Signed-off-by:
-
- 15 Jul, 2020 8 commits
-
-
Niklas Cassel authored
Add a new max_active zones definition in the sysfs documentation. This definition will be common for all devices utilizing the zoned block device support in the kernel. Export max_active_zones according to this new definition for NVMe Zoned Namespace devices, ZAC ATA devices (which are treated as SCSI devices by the kernel), and ZBC SCSI devices. Add the new max_active_zones member to struct request_queue, rather than as a queue limit, since this property cannot be split across stacking drivers. For SCSI devices, even though max active zones is not part of the ZBC/ZAC spec, export max_active_zones as 0, signifying "no limit". Signed-off-by:
Niklas Cassel <niklas.cassel@wdc.com> Reviewed-by:
Javier González <javier@javigon.com> Reviewed-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Niklas Cassel authored
Add a new max_open_zones definition in the sysfs documentation. This definition will be common for all devices utilizing the zoned block device support in the kernel. Export max open zones according to this new definition for NVMe Zoned Namespace devices, ZAC ATA devices (which are treated as SCSI devices by the kernel), and ZBC SCSI devices. Add the new max_open_zones member to struct request_queue, rather than as a queue limit, since this property cannot be split across stacking drivers. Signed-off-by:
-
Jens Axboe authored
Merge branch 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-5.9/drivers Pull MD fixes from Song. * 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md: md-cluster: fix wild pointer of unlock_all_bitmaps() md/raid5-cache: clear MD_SB_CHANGE_PENDING before flushing stripes md: fix deadlock causing by sysfs_notify md: improve io stats accounting md: raid0/linear: fix dereference before null check on pointer mddev
-
Gustavo A. R. Silva authored
Make use of the struct_size() helper instead of an open-coded version in order to avoid any potential type mistakes. Also, remove unnecessary variable _datasize_. This code was detected with the help of Coccinelle and, audited and fixed manually. Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
Stefan Haberland <sth@linux.ibm.com> Signed-off-by:
-
Stefan Haberland authored
During initialization of the DASD DIAG driver a request is issued that has a bio structure that resides on the stack. With virtually mapped kernel stacks this bio address might be in virtual storage which is unsuitable for usage with the diag250 call. In this case the device can not be set online using the DIAG discipline and fails with -EOPNOTSUP. In the system journal the following error message is presented: dasd: X.X.XXXX Setting the DASD online with discipline DIAG failed with rc=-95 Fix by allocating the bio structure instead of having it on the stack. Fixes: ce3dc447 ("s390: add support for virtually mapped kernel stacks") Signed-off-by:
Peter Oberparleiter <oberpar@linux.ibm.com> Cc: stable@vger.kernel.org #4.20 Signed-off-by:
-
Zhao Heming authored
reproduction steps: ``` node1 # mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb node2 # mdadm -A /dev/md0 /dev/sda /dev/sdb node1 # mdadm -G /dev/md0 -b none mdadm: failed to remove clustered bitmap. node1 # mdadm -S --scan ^C <==== mdadm hung & kernel crash ``` kernel stack: ``` [ 335.230657] general protection fault: 0000 [#1] SMP NOPTI [...] [ 335.230848] Call Trace: [ 335.230873] ? unlock_all_bitmaps+0x5/0x70 [md_cluster] [ 335.230886] unlock_all_bitmaps+0x3d/0x70 [md_cluster] [ 335.230899] leave+0x10f/0x190 [md_cluster] [ 335.230932] ? md_super_wait+0x93/0xa0 [md_mod] [ 335.230947] ? leave+0x5/0x190 [md_cluster] [ 335.230973] md_cluster_stop+0x1a/0x30 [md_mod] [ 335.230999] md_bitmap_free+0x142/0x150 [md_mod] [ 335.231013] ? _cond_resched+0x15/0x40 [ 335.231025] ? mutex_lock+0xe/0x30 [ 335.231056] __md_stop+0x1c/0xa0 [md_mod] [ 335.231083] do_md_stop+0x160/0x580 [md_mod] [ 335.231119] ? 0xffffffffc05fb078 [ 335.231148] md_ioctl+0xa04/0x1930 [md_mod] [ 335.231165] ? filename_lookup+0xf2/0x190 [ 335.231179] blkdev_ioctl+0x93c/0xa10 [ 335.231205] ? _cond_resched+0x15/0x40 [ 335.231214] ? __check_object_size+0xd4/0x1a0 [ 335.231224] block_ioctl+0x39/0x40 [ 335.231243] do_vfs_ioctl+0xa0/0x680 [ 335.231253] ksys_ioctl+0x70/0x80 [ 335.231261] __x64_sys_ioctl+0x16/0x20 [ 335.231271] do_syscall_64+0x65/0x1f0 [ 335.231278] entry_SYSCALL_64_after_hwframe+0x44/0xa9 ``` Signed-off-by:
-
Song Liu authored
In recovery, if we process too much data, raid5-cache may set MD_SB_CHANGE_PENDING, which causes spinning in handle_stripe(). Fix this issue by clearing the bit before flushing data only stripes. This issue was initially discussed in [1]. [1] https://www.spinics.net/lists/raid/msg64409.htmlSigned-off-by:
-
Junxiao Bi authored
The following deadlock was captured. The first process is holding 'kernfs_mutex' and hung by io. The io was staging in 'r1conf.pending_bio_list' of raid1 device, this pending bio list would be flushed by second process 'md127_raid1', but it was hung by 'kernfs_mutex'. Using sysfs_notify_dirent_safe() to replace sysfs_notify() can fix it. There were other sysfs_notify() invoked from io path, removed all of them. PID: 40430 TASK: ffff8ee9c8c65c40 CPU: 29 COMMAND: "probe_file" #0 [ffffb87c4df37260] __schedule at ffffffff9a8678ec #1 [ffffb87c4df372f8] schedule at ffffffff9a867f06 #2 [ffffb87c4df37310] io_schedule at ffffffff9a0c73e6 #3 [ffffb87c4df37328] __dta___xfs_iunpin_wait_3443 at ffffffffc03a4057 [xfs] #4 [ffffb87c4df373a0] xfs_iunpin_wait at ffffffffc03a6c79 [xfs] #5 [ffffb87c4df373b0] __dta_xfs_reclaim_inode_3357 at ffffffffc039a46c [xfs] #6 [ffffb87c4df37400] xfs_reclaim_inodes_ag at ffffffffc039a8b6 [xfs] #7 [ffffb87c4df37590] xfs_reclaim_inodes_nr at ffffffffc039bb33 [xfs] #8 [ffffb87c4df375b0] xfs_fs_free_cached_objects at ffffffffc03af0e9 [xfs] #9 [ffffb87c4df375c0] super_cache_scan at ffffffff9a287ec7 #10 [ffffb87c4df37618] shrink_slab at ffffffff9a1efd93 #11 [ffffb87c4df37700] shrink_node at ffffffff9a1f5968 #12 [ffffb87c4df37788] do_try_to_free_pages at ffffffff9a1f5ea2 #13 [ffffb87c4df377f0] try_to_free_mem_cgroup_pages at ffffffff9a1f6445 #14 [ffffb87c4df37880] try_charge at ffffffff9a26cc5f #15 [ffffb87c4df37920] memcg_kmem_charge_memcg at ffffffff9a270f6a #16 [ffffb87c4df37958] new_slab at ffffffff9a251430 #17 [ffffb87c4df379c0] ___slab_alloc at ffffffff9a251c85 #18 [ffffb87c4df37a80] __slab_alloc at ffffffff9a25635d #19 [ffffb87c4df37ac0] kmem_cache_alloc at ffffffff9a251f89 #20 [ffffb87c4df37b00] alloc_inode at ffffffff9a2a2b10 #21 [ffffb87c4df37b20] iget_locked at ffffffff9a2a4854 #22 [ffffb87c4df37b60] kernfs_get_inode at ffffffff9a311377 #23 [ffffb87c4df37b80] kernfs_iop_lookup at ffffffff9a311e2b #24 [ffffb87c4df37ba8] lookup_slow at ffffffff9a290118 #25 [ffffb87c4df37c10] walk_component at ffffffff9a291e83 #26 [ffffb87c4df37c78] path_lookupat at ffffffff9a293619 #27 [ffffb87c4df37cd8] filename_lookup at ffffffff9a2953af #28 [ffffb87c4df37de8] user_path_at_empty at ffffffff9a295566 #29 [ffffb87c4df37e10] vfs_statx at ffffffff9a289787 #30 [ffffb87c4df37e70] SYSC_newlstat at ffffffff9a289d5d #31 [ffffb87c4df37f18] sys_newlstat at ffffffff9a28a60e #32 [ffffb87c4df37f28] do_syscall_64 at ffffffff9a003949 #33 [ffffb87c4df37f50] entry_SYSCALL_64_after_hwframe at ffffffff9aa001ad RIP: 00007f617a5f2905 RSP: 00007f607334f838 RFLAGS: 00000246 RAX: ffffffffffffffda RBX: 00007f6064044b20 RCX: 00007f617a5f2905 RDX: 00007f6064044b20 RSI: 00007f6064044b20 RDI: 00007f6064005890 RBP: 00007f6064044aa0 R8: 0000000000000030 R9: 000000000000011c R10: 0000000000000013 R11: 0000000000000246 R12: 00007f606417e6d0 R13: 00007f6064044aa0 R14: 00007f6064044b10 R15: 00000000ffffffff ORIG_RAX: 0000000000000006 CS: 0033 SS: 002b PID: 927 TASK: ffff8f15ac5dbd80 CPU: 42 COMMAND: "md127_raid1" #0 [ffffb87c4df07b28] __schedule at ffffffff9a8678ec #1 [ffffb87c4df07bc0] schedule at ffffffff9a867f06 #2 [ffffb87c4df07bd8] schedule_preempt_disabled at ffffffff9a86825e #3 [ffffb87c4df07be8] __mutex_lock at ffffffff9a869bcc #4 [ffffb87c4df07ca0] __mutex_lock_slowpath at ffffffff9a86a013 #5 [ffffb87c4df07cb0] mutex_lock at ffffffff9a86a04f #6 [ffffb87c4df07cc8] kernfs_find_and_get_ns at ffffffff9a311d83 #7 [ffffb87c4df07cf0] sysfs_notify at ffffffff9a314b3a #8 [ffffb87c4df07d18] md_update_sb at ffffffff9a688696 #9 [ffffb87c4df07d98] md_update_sb at ffffffff9a6886d5 #10 [ffffb87c4df07da8] md_check_recovery at ffffffff9a68ad9c #11 [ffffb87c4df07dd0] raid1d at ffffffffc01f0375 [raid1] #12 [ffffb87c4df07ea0] md_thread at ffffffff9a680348 #13 [ffffb87c4df07f08] kthread at ffffffff9a0b8005 #14 [ffffb87c4df07f50] ret_from_fork at ffffffff9aa00344 Signed-off-by:Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
-
- 14 Jul, 2020 2 commits
-
-
Artur Paszkiewicz authored
Use generic io accounting functions to manage io stats. There was an attempt to do this earlier in commit 18c0b223 ("md: use generic io stats accounting functions to simplify io stat accounting"), but it did not include a call to generic_end_io_acct() and caused issues with tracking in-flight IOs, so it was later removed in commit 74672d06 ("md: fix md io stats accounting broken"). This patch attempts to fix this by using both disk_start_io_acct() and disk_end_io_acct(). To make it possible, a struct md_io is allocated for every new md bio, which includes the io start_time. A new mempool is introduced for this purpose. We override bio->bi_end_io with our own callback and call disk_start_io_acct() before passing the bio to md_handle_request(). When it completes, we call disk_end_io_acct() and the original bi_end_io callback. This adds correct statistics about in-flight IOs and IO processing time, interpreted e.g. in iostat as await, svctm, aqu-sz and %util. It also fixes a situation where too many IOs where reported if a bio was re-submitted to the mddev, because io accounting is now performed only on newly arriving bios. Acked-by:
Artur Paszkiewicz <artur.paszkiewicz@intel.com> Signed-off-by:
-
Colin Ian King authored
Pointer mddev is being dereferenced with a test_bit call before mddev is being null checked, this may cause a null pointer dereference. Fix this by moving the null pointer checks to sanity check mddev before it is dereferenced. Addresses-Coverity: ("Dereference before null check") Fixes: 62f7b198 ("md raid0/linear: Mark array as 'broken' and fail BIOs if a member is gone") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Guilherme G. Piccoli <gpiccoli@canonical.com> Signed-off-by:
-
- 11 Jul, 2020 1 commit
-
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script bellow. It has been compile tested. This also aligns code with what is in use in '/rsxx/dma.c' @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
- 10 Jul, 2020 1 commit
-
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "Below is the current large chunk we have in the nvme tree for 5.9: - ZNS support (Aravind, Keith, Matias, Niklas) - misc cleanups and optimizations (Baolin, Chaitanya, David, Dongli, Max, Sagi)" * 'nvme-5.9' of git://git.infradead.org/nvme: (28 commits) nvme: remove ns->disk checks nvme-pci: use standard block status symbolic names nvme-pci: use the consistent return type of nvme_pci_iod_alloc_size() nvme-pci: add a blank line after declarations nvme-pci: fix some comments issues nvme-pci: remove redundant segment validation nvme: document quirked Intel models nvme: expose reconnect_delay and ctrl_loss_tmo via sysfs nvme: support for zoned namespaces nvme: support for multiple Command Sets Supported and Effects log pages nvme: implement multiple I/O Command Set support null_blk: introduce zone capacity for zoned device block: add capacity field to zone descriptors nvme: use USEC_PER_SEC instead of magic numbers nvmet-tcp: simplify nvmet_process_resp_list nvme-tcp: optimize network stack with setting msg flags according to batch size nvme-tcp: leverage request plugging nvme-tcp: have queue prod/cons send list become a llist nvme-fcloop: verify wwnn and wwpn format nvmet: use unsigned type for u64 ...
-
- 08 Jul, 2020 16 commits
-
-
Christoph Hellwig authored
By the time a namespace is added to ctrl->namespaces list and thus can be looked up ns->disk has been assigned, and it it never cleared. Remove all the checks for ns->disk being NULL. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Keith Busch <kbusch@kernel.org> Reviewed-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
-
Baolin Wang authored
Signed-off-by:
Baolin Wang <baolin.wang@linux.alibaba.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
-
Baolin Wang authored
The nvme_pci_iod_alloc_size() should return 'size_t' type to be consistent with the sizeof return value. Signed-off-by:
-
Baolin Wang authored
Add a blank line after declarations to make code more readable. Signed-off-by:
-
Baolin Wang authored
Fix comment typos and remove whitespaces before tabs to cleanup checkpatch errors. Signed-off-by:
-
Baolin Wang authored
We've validated the segment counts before calling nvme_map_data(), so there is no need to validate again in nvme_pci_use_sgls(, which is only called from nvme_map_data(). Signed-off-by:
-
David Fugate authored
Documented model names of Intel SSDs requiring quirks. Signed-off-by:
David Fugate <david.fugate@linux.intel.com> Signed-off-by:
-
Sagi Grimberg authored
This is useful information, and moreover its it's useful to be able to alter these parameters per controller after it has been established. Signed-off-by:
-
Keith Busch authored
Add support for NVM Express Zoned Namespaces (ZNS) Command Set defined in NVM Express TP4053. Zoned namespaces are discovered based on their Command Set Identifier reported in the namespaces Namespace Identification Descriptor list. A successfully discovered Zoned Namespace will be registered with the block layer as a host managed zoned block device with Zone Append command support. A namespace that does not support append is not supported by the driver. Reviewed-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
Javier González <javier.gonz@samsung.com> Reviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Hans Holmberg <hans.holmberg@wdc.com> Signed-off-by:
Dmitry Fomichev <dmitry.fomichev@wdc.com> Signed-off-by:
Ajay Joshi <ajay.joshi@wdc.com> Signed-off-by:
Aravind Ramesh <aravind.ramesh@wdc.com> Signed-off-by:
Matias Bjørling <matias.bjorling@wdc.com> Signed-off-by:
Keith Busch <keith.busch@wdc.com> Signed-off-by:
-
Keith Busch authored
The Commands Supported and Effects log page was extended with a CSI field that enables the host to query the log page for each command set supported. Retrieve this log page for each command set that an attached namespace supports, and save a pointer to that log in the namespace head. Reviewed-by:
Daniel Wagner <dwagner@suse.de> Signed-off-by:
-
Niklas Cassel authored
Implements support for multiple I/O Command Sets. NVMe TP 4056 introduces a method to enumerate multiple command sets per namespace. If the command set is exposed, this method for enumeration will be used instead of the traditional method that uses the CC.CSS register command set register for command set identification. For namespaces where the Command Set Identifier is not supported or recognized, the specific namespace will not be created. Reviewed-by:
-
Aravind Ramesh authored
Allow emulation of a zoned device with a per zone capacity smaller than the zone size as as defined in the Zoned Namespace (ZNS) Command Set specification. The zone capacity defaults to the zone size if not specified and must be smaller than the zone size otherwise. Reviewed-by:
-
Matias Bjørling authored
In the zoned storage model, the sectors within a zone are typically all writeable. With the introduction of the Zoned Namespace (ZNS) Command Set in the NVM Express organization, the model was extended to have a specific writeable capacity. Extend the zone descriptor data structure with a zone capacity field to indicate to the user how many sectors in a zone are writeable. Introduce backward compatibility in the zone report ioctl by extending the zone report header data structure with a flags field to indicate if the capacity field is available. Reviewed-by:
-
Baolin Wang authored
Use USEC_PER_SEC instead of magic numbers to make code more readable. Reviewed-by:
-
Sagi Grimberg authored
We can make it shorter and simpler without some redundant checks. Signed-off-by:
-
Sagi Grimberg authored
If we have a long list of request to send, signal the network stack that more is coming (MSG_MORE). If we have nothing else, signal MSG_EOR. Signed-off-by:
Mark Wunderlich <mark.wunderlich@intel.com> Signed-off-by:
-
