In this commit, we make it possible to send connectionless unicast
messages to any member corresponding to the given member identity,
when there is more than one such member. The sender must use a
TIPC_ADDR_NAME address to achieve this effect.

We also perform load balancing between the destinations, i.e., we
primarily select one which has advertised sufficient send window
to not cause a block/EAGAIN delay, if any. This mechanism is
overlayed on the always present round-robin selection.

Anycast messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We now make it possible to send connectionless unicast messages
within a communication group. To send a message, the sender can use
either a direct port address, aka port identity, or an indirect port
name to be looked up.

This type of messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We introduce an end-to-end flow control mechanism for group broadcast
messages. This ensures that no messages are ever lost because of
destination receive buffer overflow, with minimal impact on performance.
For now, the algorithm is based on the assumption that there is only one
active transmitter at any moment in time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like with any other service, group members' availability can be
subscribed for by connecting to be topology server. However, because
the events arrive via a different socket than the member socket, there
is a real risk that membership events my arrive out of synch with the
actual JOIN/LEAVE action. I.e., it is possible to receive the first
messages from a new member before the corresponding JOIN event arrives,
just as it is possible to receive the last messages from a leaving
member after the LEAVE event has already been received.

Since each member socket is internally also subscribing for membership
events, we now fix this problem by passing those events on to the user
via the member socket. We leverage the already present member synch-
ronization protocol to guarantee correct message/event order. An event
is delivered to the user as an empty message where the two source
addresses identify the new/lost member. Furthermore, we set the MSG_OOB
bit in the message flags to mark it as an event. If the event is an
indication about a member loss we also set the MSG_EOR bit, so it can
be distinguished from a member addition event.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With group communication, it becomes important for a message receiver to
identify not only from which socket (identfied by a node:port tuple) the
message was sent, but also the logical identity (type:instance) of the
sending member.

We fix this by adding a second instance of struct sockaddr_tipc to the
source address area when a message is read. The extra address struct
is filled in with data found in the received message header (type,) and
in the local member representation struct (instance.)
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a preparation for introducing flow control for multicast and datagram
messaging we need a more strictly defined framework than we have now. A
socket must be able keep track of exactly how many and which other
sockets it is allowed to communicate with at any moment, and keep the
necessary state for those.

We therefore introduce a new concept we have named Communication Group.
Sockets can join a group via a new setsockopt() call TIPC_GROUP_JOIN.
The call takes four parameters: 'type' serves as group identifier,
'instance' serves as an logical member identifier, and 'scope' indicates
the visibility of the group (node/cluster/zone). Finally, 'flags' makes
it possible to set certain properties for the member. For now, there is
only one flag, indicating if the creator of the socket wants to receive
a copy of broadcast or multicast messages it is sending via the socket,
and if wants to be eligible as destination for its own anycasts.

A group is closed, i.e., sockets which have not joined a group will
not be able to send messages to or receive messages from members of
the group, and vice versa.

Any member of a group can send multicast ('group broadcast') messages
to all group members, optionally including itself, using the primitive
send(). The messages are received via the recvmsg() primitive. A socket
can only be member of one group at a time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We often see a need for a linked list of destination identities,
sometimes containing a port number, sometimes a node identity, and
sometimes both. The currently defined struct u32_list is not generic
enough to cover all cases, so we extend it to contain two u32 integers
and rename it to struct tipc_dest_list.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We see an increasing need to send multiple single-buffer messages
of TIPC_SYSTEM_IMPORTANCE to different individual destination nodes.
Instead of looping over the send queue and sending each buffer
individually, as we do now, we add a new help function
tipc_node_distr_xmit() to do this.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the following commits we will need to handle multiple incoming and
rejected/returned buffers in the function socket.c::filter_rcv().
As a preparation for this, we generalize the function by handling
buffer queues instead of individual buffers. We also introduce a
help function tipc_skb_reject(), and rename filter_rcv() to
tipc_sk_filter_rcv() in line with other functions in socket.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the coming commits, functions at the socket level will need the
ability to read the availability status of a given node. We therefore
introduce a new function for this purpose, while renaming the existing
static function currently having the wanted name.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The address given to tipc_connect() is not completely sanity checked,
under the assumption that this will be done later in the function
__tipc_sendmsg() when the address is used there.

However, the latter functon will in the next commits serve as caller
to several other send functions, so we want to move the corresponding
sanity check there to the beginning of that function, before we possibly
need to grab the address stored by tipc_connect(). We must therefore
be able to trust that this address already has been thoroughly checked.

We do this in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As preparation for introducing communication groups, we add the ability
to issue topology subscriptions and receive topology events from kernel
space. This will make it possible for group member sockets to keep track
of other group members.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The module clock is used for two purposes:
  - Wake-on-LAN (WoL), which is optional,
  - gPTP Timer Increment (GTI) configuration, which is mandatory.

As the clock is needed for GTI configuration anyway, WoL is always
available.  Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rafał Miłecki says:

====================
net: support bgmac with B50212E B1 PHY

I got a report that a board with BCM47189 SoC and B50212E B1 PHY doesn't
work well some devices as there is massive ping loss. After analyzing
PHY state it has appeared that is runs in slave mode and doesn't auto
switch to master properly when needed.

This patchset fixes this by:
1) Adding new flag support to the PHY driver for setting master mode
2) Modifying bgmac to request master mode for reported hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.

So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.

So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LM
http://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.

This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the underlying master ever changes its L2 (e.g. bonding device),
then make sure that the IPvlan slaves always emit packets with the
current L2 of the master instead of the stale mac addr which was
copied during the device creation. The problem can be seen with
following script -

  #!/bin/bash
  # Create a vEth pair
  ip link add dev veth0 type veth peer name veth1
  ip link set veth0 up
  ip link set veth1 up
  ip link show veth0
  ip link show veth1
  # Create an IPvlan device on one end of this vEth pair.
  ip link add link veth0 dev ipvl0 type ipvlan mode l2
  ip link show ipvl0
  # Change the mac-address of the vEth master.
  ip link set veth0 address 02:11:22:33:44:55

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
sched: act: ife: UAPI checks and performance tweaks

this patch series contains at first a patch which adds a check for
IFE_ENCODE and IFE_DECODE when a ife act gets created or updated and adding
handling of these cases only inside the act callback only.

The second patch use per-cpu counters and move the spinlock around so that
the spinlock is less being held in act callback.

The last patch use rcu for update parameters and also move the spinlock for
the same purpose as in patch 2.

Notes:
 - There is still a spinlock around for protecting the metalist and a
   rw-lock for another list. Should be migrated to a rcu list, ife
   possible.

 - I use still dereference in dump callback, so I think what I didn't
   got was what happened when rcu_assign_pointer will do when rcu read
   lock is held. I suppose the pointer will be updated, then we don't
   have any issue here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the parameter updating via RCU and not protected by a
spinlock anymore. This reduce the time that the spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch migrates the current counter handling which is protected by a
spinlock to a per-cpu counter handling. This reduce the time where the
spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the check of the two possible ife handlings encode
and decode to the init callback. The decode value is for usability
aspect and used in userspace code only. The current code offers encode
else decode only. This patch avoids any other option than this.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roman Mashak says:

====================
net: sched: Fix IFE meta modules loading

Adjust module alias names of IFE meta modules and fix the bug that
prevented auto-loading IFE modules in run-time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Macro __stringify_1() can stringify a macro argument, however IFE_META_*
are enums, so they never expand, however request_module expects an integer
in IFE module name, so as a result it always fails to auto-load.

Fixes: ef6980b6 ("introduce IFE action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make style of module alias name consistent with other subsystems in kernel,
for example net devices.

Fixes: 084e2f65 ("Support to encoding decoding skb mark on IFE action")
Fixes: 200e10f4 ("Support to encoding decoding skb prio on IFE action")
Fixes: 408fbc22 ("net sched ife action: Introduce skb tcindex metadata encap decap")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete unused channel variables in vxge-traffic.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This file contains unnecessary whitespaces as newlines, remove them,
found by looking at what struct tc_mirred looks like.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When af_mpls is built-in but the tunnel support is a module,
we get a link failure:

net/mpls/af_mpls.o: In function `mpls_init':
af_mpls.c:(.init.text+0xdc): undefined reference to `ip_tunnel_encap_add_ops'

This adds a Kconfig statement to prevent the broken
configuration and force mpls to be a module as well in
this case.

Fixes: bdc47641 ("ip_tunnel: add mpls over gre support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Amine Kherbouche <amine.kherbouche@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: ib_query_gid() patches

triggered by Parav Pandit here are 2 cleanup patches for usage of
ib_query_gid() in the smc-code.

Thanks, Ursula

v2 changes advised by Parav Pandit:
   extra check is_vlan_dev() in patch 2/2
   "RoCE" spelling
   added "Reported-by"
   added "Reviewed-by"
   added "Fixes"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For RoCEs ib_query_gid() takes a reference count on the net_device.
This reference count must be decreased by the caller.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Fixes: 0cfdd8f9 ("smc: connection and link group creation")
Signed-off-by: David S. Miller <davem@davemloft.net>

SMC should not open code the function pointer get_netdev of the
IB device. Replacing ib_query_gid(..., NULL) with
ib_query_gid(..., gid_attr) allows access to the netdev.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Suggested-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Enable ACB for bcm_sf2 and bcmsysport

This patch series enables Broadcom's Advanced Congestion Buffering mechanism
which requires cooperation between the CPU/Management Ethernet MAC controller
and the switch.

I took the notifier approach because ultimately the information we need to
carry to the master network device is DSA specific and I saw little room for
generalizing beyond what DSA requires. Chances are that this is highly specific
to the Broadcom HW as I don't know of any HW out there that supports something
nearly similar for similar or identical needs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have established the queue mapping between the switch port
egress queues and the SYSTEMPORT egress queues, we can turn on Advanced
Congestion Buffering (ACB) at the SYSTEMPORT level. This enables the
Ethernet MAC controller to get out of band flow control information
directly from the switch port and queue that it monitors such that its
internal TDMA can be appropriately backpressured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.

This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Establish a queue mapping between the DSA slave network device queues
created that correspond to switch port queues, and the transmit queue
that SYSTEMPORT manages.

We need to configure the SYSTEMPORT transmit queue with the switch port number
and switch port queue number in order for the switch and SYSTEMPORT hardware to
utilize the out of band congestion notification. This hardware mechanism works
by looking at the switch port egress queue and determines whether there is
enough buffers for this queue, with that class of service for a successful
transmission and if not, backpressures the SYSTEMPORT queue that is being used.

For this to work, we implement a notifier which looks at the
DSA_PORT_REGISTER event.  When DSA network devices are registered, the
framework calls the DSA notifiers when that happens, extracts the number
of queues for these devices and their associated port number, remembers
that in the driver private structure and linearly maps those queues to
TX rings/queues that we manage.

This scheme works because DSA slave network deviecs always transmit
through SYSTEMPORT so when DSA slave network devices are
destroyed/brought down, the corresponding SYSTEMPORT queues are no
longer used. Also, by design of the DSA framework, the master network
device (SYSTEMPORT) is registered first.

For faster lookups we use an array of up to DSA_MAX_PORTS * number of
queues per port, and then map pointers to bcm_sysport_tx_ring such that
our ndo_select_queue() implementation can just index into that array to
locate the corresponding ring index.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.

This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit df1ec1b9.

It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove three inline helpers that are no longer needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable old_flags is being assigned but is never read; it is redundant
and can be removed.

Cleans up clang warning: Value stored to 'old_flags' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>