- 31 May, 2014 10 commits
-
-
Soren Brinkmann authored
commit c12d82b8 upstream. Add CONFIG_BLK_DEV_INITRD to the defconfig to support initramfs and initrd. Signed-off-by:
Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefan Richter authored
commit 0ca49345 upstream. Since commit bd972688 "firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8", there is a high chance that firewire-ohci fails to initialize LSI née Agere controllers. https://bugzilla.kernel.org/show_bug.cgi?id=65151 Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more than 10 ms elapse from the reassertion of LPS until the interface is reset. The link shall not assert LReq until the reset is complete." In other words, the link needs to give the PHY at least 10 ms to get the interface operational. With just the msleep(1) in bd972688, the first read_phy_reg() during ohci_enable() may happen before the phy-link interface reset was finished, and fail. Due to the high variability of msleep(n) with small n, this failure was not fully reproducible, and not apparent at all with low CONFIG_HZ setting. On the other hand, Peter can no longer reproduce the issue with FW643 rev8. The read phy reg failures that happened back then may have had an unrelated cause. So, just revert bd972688, except for the valid comment on TSB82AA2 cards. Reported-by: Mikhail Gavrilov Reported-by:
Jay Fenlason <fenlason@redhat.com> Reported-by:
Clemens Ladisch <clemens@ladisch.de> Reported-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Stefan Richter authored
commit 0dbe15f8 upstream. a) Sort device IDs by vendor -- device -- revision. b) Write quirk flags in hexadecimal. This affects the user-visible output of "modinfo firewire-ohci". Since more flags have been added recently, it is now easier to cope with them in hexadecimal represen- tation. Besides, the device-specific combination of quirk flags is shown in hexadecimal in the kernel log too. (And firewire-sbp2 presents its own quirk flags in modinfo as hexadecimals as well.) Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 7dec935a upstream. No reason to allocate tp_module structures for modules that have no tracepoints. This just wastes memory. Fixes: b75ef8b4 "Tracepoint: Dissociate from module mutex" Acked-by:
Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Thomas Graf authored
commit c58dd2dd upstream. All xtables variants suffer from the defect that the copy_to_user() to copy the counters to user memory may fail after the table has already been exchanged and thus exposed. Return an error at this point will result in freeing the already exposed table. Any subsequent packet processing will result in a kernel panic. We can't copy the counters before exposing the new tables as we want provide the counter state after the old table has been unhooked. Therefore convert this into a silent error. Cc: Florian Westphal <fw@strlen.de> Signed-off-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Andrey Vagin authored
commit 223b02d9 upstream. "len" contains sizeof(nf_ct_ext) and size of extensions. In a worst case it can contain all extensions. Bellow you can find sizes for all types of extensions. Their sum is definitely bigger than 256. nf_ct_ext_types[0]->len = 24 nf_ct_ext_types[1]->len = 32 nf_ct_ext_types[2]->len = 24 nf_ct_ext_types[3]->len = 32 nf_ct_ext_types[4]->len = 152 nf_ct_ext_types[5]->len = 2 nf_ct_ext_types[6]->len = 16 nf_ct_ext_types[7]->len = 8 I have seen "len" up to 280 and my host has crashes w/o this patch. The right way to fix this problem is reducing the size of the ecache extension (4) and Florian is going to do this, but these changes will be quite large to be appropriate for a stable tree. Fixes: 5b423f6a (netfilter: nf_conntrack: fix racy timer handling with reliable) Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by:
Andrey Vagin <avagin@openvz.org> Signed-off-by:
-
Roman Pen authored
commit af5040da upstream. trace_block_rq_complete does not take into account that request can be partially completed, so we can get the following incorrect output of blkparser: C R 232 + 240 [0] C R 240 + 232 [0] C R 248 + 224 [0] C R 256 + 216 [0] but should be: C R 232 + 8 [0] C R 240 + 8 [0] C R 248 + 8 [0] C R 256 + 8 [0] Also, the whole output summary statistics of completed requests and final throughput will be incorrect. This patch takes into account real completion size of the request and fixes wrong completion accounting. Signed-off-by:
Roman Pen <r.peniaev@gmail.com> CC: Steven Rostedt <rostedt@goodmis.org> CC: Frederic Weisbecker <fweisbec@gmail.com> CC: Ingo Molnar <mingo@redhat.com> CC: linux-kernel@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Dan Carpenter authored
commit 3de22601 upstream. pthru32->dataxferlen comes from the user so we need to check that it's not too large so we don't overflow the buffer. Reported-by:
Nico Golde <nico@ngolde.de> Reported-by:
Fabian Yamaguchi <fabs@goesec.de> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Sumit Saxena <sumit.saxena@lsi.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
James Bottomley authored
commit f2495e22 upstream. In the highly unusual case where two threads are running concurrently through the scanning code scanning the same target, we run into the situation where one may allocate the target while the other is still using it. In this case, because the reap checks for STARGET_CREATED and kills the target without reference counting, the second thread will do the wrong thing on reap. Fix this by reference counting even creates and doing the STARGET_CREATED check in the final put. Tested-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
James Bottomley authored
commit e63ed0d7 upstream. This patch eliminates the reap_ref and replaces it with a proper kref. On last put of this kref, the target is removed from visibility in sysfs. The final call to scsi_target_reap() for the device is done from __scsi_remove_device() and only if the device was made visible. This ensures that the target disappears as soon as the last device is gone rather than waiting until final release of the device (which is often too long). Reviewed-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
-
- 13 May, 2014 30 commits
-
-
Greg Kroah-Hartman authored
-
Vineet Gupta authored
commit 8aa9e85a upstream. There was a very small race window where resume to kernel mode from a Exception Path (or pure kernel mode which is true for most of ARC exceptions anyways), was not disabling interrupts in restore_regs, clobbering the exception regs Anton found the culprit call flow (after many sleepless nights) | 1. we got a Trap from user land | 2. started to service it. | 3. While doing some stuff on user-land memory (I think it is padzero()), | we got a DataTlbMiss | 4. On return from it we are taking "resume_kernel_mode" path | 5. NEED_RESHED is not set, so we go to "return from exception" path in | restore regs. | 6. there seems to be IRQ happening Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Cc: Anton Kolesov <Anton.Kolesov@synopsys.com> Cc: Francois Bedard <Francois.Bedard@synopsys.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Gerd Hoffmann authored
commit 2f1e8007 upstream. cirrus kms driver lacks power management support, thus the vga display doesn't work any more after S3 resume. Fix this by adding suspend and resume functions. Also make the mode_set function unblank the screen. Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Hans de Goede authored
commit 27a38856 upstream. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Hans de Goede authored
commit 46a2986e upstream. We expect that all the Haswell series will need such quirks, sigh. The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad, with the same min/max issue. The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation. The X1 and T431s share a PnPID with the T540p, but the reported ranges are closer to those of the T440s. HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me, S1 Yoga and X1 are written by Benjamin Tissoires. Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the X240, X1 uses the same touchpad as the T440. Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Jeff Layton authored
commit 679b033d upstream. We had a Fedora ABRT report with a stack trace like this: kernel BUG at net/sunrpc/svc.c:550! invalid opcode: 0000 [#1] SMP [...] CPU: 2 PID: 913 Comm: rpc.nfsd Not tainted 3.13.6-200.fc20.x86_64 #1 Hardware name: Hewlett-Packard HP ProBook 4740s/1846, BIOS 68IRR Ver. F.40 01/29/2013 task: ffff880146b00000 ti: ffff88003f9b8000 task.ti: ffff88003f9b8000 RIP: 0010:[<ffffffffa0305fa8>] [<ffffffffa0305fa8>] svc_destroy+0x128/0x130 [sunrpc] RSP: 0018:ffff88003f9b9de0 EFLAGS: 00010206 RAX: ffff88003f829628 RBX: ffff88003f829600 RCX: 00000000000041ee RDX: 0000000000000000 RSI: 0000000000000286 RDI: 0000000000000286 RBP: ffff88003f9b9de8 R08: 0000000000017360 R09: ffff88014fa97360 R10: ffffffff8114ce57 R11: ffffea00051c9c00 R12: ffff88003f829600 R13: 00000000ffffff9e R14: ffffffff81cc7cc0 R15: 0000000000000000 FS: 00007f4fde284840(0000) GS:ffff88014fa80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f4fdf5192f8 CR3: 00000000a569a000 CR4: 00000000001407e0 Stack: ffff88003f792300 ffff88003f9b9e18 ffffffffa02de02a 0000000000000000 ffffffff81cc7cc0 ffff88003f9cb000 0000000000000008 ffff88003f9b9e60 ffffffffa033bb35 ffffffff8131c86c ffff88003f9cb000 ffff8800a5715008 Call Trace: [<ffffffffa02de02a>] lockd_up+0xaa/0x330 [lockd] [<ffffffffa033bb35>] nfsd_svc+0x1b5/0x2f0 [nfsd] [<ffffffff8131c86c>] ? simple_strtoull+0x2c/0x50 [<ffffffffa033c630>] ? write_pool_threads+0x280/0x280 [nfsd] [<ffffffffa033c6bb>] write_threads+0x8b/0xf0 [nfsd] [<ffffffff8114efa4>] ? __get_free_pages+0x14/0x50 [<ffffffff8114eff6>] ? get_zeroed_page+0x16/0x20 [<ffffffff811dec51>] ? simple_transaction_get+0xb1/0xd0 [<ffffffffa033c098>] nfsctl_transaction_write+0x48/0x80 [nfsd] [<ffffffff811b8b34>] vfs_write+0xb4/0x1f0 [<ffffffff811c3f99>] ? putname+0x29/0x40 [<ffffffff811b9569>] SyS_write+0x49/0xa0 [<ffffffff810fc2a6>] ? __audit_syscall_exit+0x1f6/0x2a0 [<ffffffff816962e9>] system_call_fastpath+0x16/0x1b Code: 31 c0 e8 82 db 37 e1 e9 2a ff ff ff 48 8b 07 8b 57 14 48 c7 c7 d5 c6 31 a0 48 8b 70 20 31 c0 e8 65 db 37 e1 e9 f4 fe ff ff 0f 0b <0f> 0b 66 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 RIP [<ffffffffa0305fa8>] svc_destroy+0x128/0x130 [sunrpc] RSP <ffff88003f9b9de0> Evidently, we created some lockd sockets and then failed to create others. make_socks then returned an error and we tried to tear down the svc, but svc->sv_permsocks was not empty so we ended up tripping over the BUG() in svc_destroy(). Fix this by ensuring that we tear down any live sockets we created when socket creation is going to return an error. Fixes: 786185b5 (SUNRPC: move per-net operations from...) Reported-by:
Raphos <raphoszap@laposte.net> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Reviewed-by:
Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit fe76cd88 upstream. If unable to ensure_next_mapping() we must add the current bio, which was removed from the @bios list via bio_list_pop, back to the deferred_bios list before all the remaining @bios. Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Acked-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit a9d45396 upstream. The persistent-data library used by dm-thin, dm-cache, etc is transactional. If anything goes wrong, such as an io error when writing new metadata or a power failure, then we roll back to the last transaction. Atomicity when committing a transaction is achieved by: a) Never overwriting data from the previous transaction. b) Writing the superblock last, after all other metadata has hit the disk. This commit and the following commit ("dm: take care to copy the space map roots before locking the superblock") fix a bug associated with (b). When committing it was possible for the superblock to still be written in spite of an io error occurring during the preceeding metadata flush. With these commits we're careful not to take the write lock out on the superblock until after the metadata flush has completed. Change the transaction manager's semantics for dm_tm_commit() to assume all data has been flushed _before_ the single superblock that is passed in. As a prerequisite, split the block manager's block unlocking and flushing by simplifying dm_bm_flush_and_unlock() to dm_bm_flush(). Now the unlocking must be done separately. This issue was discovered by forcing io errors at the crucial time using dm-flakey. Signed-off-by:
-
Giacomo Comes authored
commit 10b6ee4a upstream. The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port. The call intel_crt_init freeze the machine, so skip such call. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559 Signed-off-by: Giacomo Comes <comes at naic.edu> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Dan Carpenter authored
commit b4c23305 upstream. We always put a NUL terminator one space past the end of the "vendor" buffer. Walter Harms also pointed out that this should just use kstrndup(). Fixes: 7d17c02a ('mtd: Add new SmartMedia/xD FTL') Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit c69dbbf3 upstream. Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR" which is NULL and not a valid register. Fixes: 8bff82cb ('mtd: add nand support for w90p910 (v2)') Signed-off-by:
-
Herve Codina authored
commit 90445ff6 upstream. Crash detected on sam5d35 and its pmecc nand ecc controller. The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc (nand_base.c) when we write a sub page. chip->ecc.hwctl function is not set when we are using PMECC controller. As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in order to disable sub page access in nand_write_page. Signed-off-by:
Herve Codina <Herve.CODINA@celad.com> Acked-by:
Josh Wu <josh.wu@atmel.com> Signed-off-by:
-
Mikulas Patocka authored
commit 6b0df682 upstream. The functions for data copying copyarea_foreward_8bpp and copyarea_backward_8bpp are buggy, they produce screen corruption. This patch fixes the functions and moves the logic to one function "copyarea_8bpp". For simplicity, the function only handles copying that is aligned on 8 pixes. If we copy an unaligned area, generic function cfb_copyarea is used. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Marek Vasut authored
commit a585f87c upstream. The scenario here is that someone calls enable_irq_wake() from somewhere in the code. This will result in the lockdep producing a backtrace as can be seen below. In my case, this problem is triggered when using the wl1271 (TI WlCore) driver found in drivers/net/wireless/ti/ . The problem cause is rather obvious from the backtrace, but let's outline the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(), which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq() calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not marked as recursive, lockdep will spew the stuff below. We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to fix the spew. ============================================= [ INFO: possible recursive locking detected ] 3.10.33-00012-gf06b763-dirty #61 Not tainted --------------------------------------------- kworker/0:1/18 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 3 locks held by kworker/0:1/18: #0: (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4 #1: ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4 #2: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 stack backtrace: CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61 Workqueue: events request_firmware_work_func [<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14) [<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64) [<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104) [<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44) [<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58) [<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4) [<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394) [<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0) [<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34) wlcore: loaded Signed-off-by:
Marek Vasut <marex@denx.de> Acked-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Colin Ian King authored
commit 328e203f upstream. static code analysis from cppcheck reports: [drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]: (error) Uninitialized variable: packet_beacon packet_beacon is not initialized and hence packet_beacon contains garbage from the stack, so set it to false. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Larry Finger authored
commit 5f918699 upstream. Beginning with kernel 3.13, this driver fails on some systems. The problem was bisected to: Commit 1bf4bbb4 Author: Felix Fietkau <nbd@openwrt.org> Title: mac80211: send control port protocol frames to the VO queue There is noting wrong with the above commit. The regression occurs because V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to modify the rtl8192se routine that sets the correct transmit queue. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541Reported-by:
Alex Miller <almiller_1@yahoo.co.uk> Tested-by:
-
Larry Finger authored
commit 2610decd upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8192se. Signed-off-by:
-
Larry Finger authored
commit a53268be upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8192cu. Signed-off-by:
-
Larry Finger authored
commit 6b639271 upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8188ee. Signed-off-by:
-
Larry Finger authored
commit bfc1010c upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8723ae. Signed-off-by:
-
Jeff Layton authored
commit 4991a628 upstream. A fl->fl_break_time of 0 has a special meaning to the lease break code that basically means "never break the lease". knfsd uses this to ensure that leases don't disappear out from under it. Unfortunately, the code in __break_lease can end up passing this value to wait_event_interruptible as a timeout, which prevents it from going to sleep at all. This causes __break_lease to spin in a tight loop and causes soft lockups. Fix this by ensuring that we pass a minimum value of 1 as a timeout instead. Cc: J. Bruce Fields <bfields@fieldses.org> Reported-by:
Terry Barnaby <terry1@beam.ltd.uk> Signed-off-by:
-
Felix Fietkau authored
commit 764152ff upstream. Their power value is initialized to zero. This patch fixes an issue where the configured power drops to the minimum value when AP_VLAN interfaces are created/removed. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
commit 115b943a upstream. Jouni reported that when doing off-channel transmissions mixed with on-channel transmissions, the on-channel ones ended up on the off-channel in some cases. The reason for that is that during the refactoring of the off- channel code, I lost the part that stopped all activity and as a consequence the on-channel frames (including data frames) were no longer queued but would be transmitted on the temporary channel. Fix this by simply restoring the lost activity stop call. Fixes: 2eb278e0 ("mac80211: unify SW/offload remain-on-channel") Reported-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
-
Michael Braun authored
commit 112c44b2 upstream. commit de74a1d9 "mac80211: fix WPA with VLAN on AP side with ps-sta" fixed an issue where queued multicast packets would be sent out encrypted with the key of an other bss. commit "7cbf9d01" "mac80211: fix oops on mesh PS broadcast forwarding" essentially reverted it, because vif.type cannot be AP_VLAN due to the check to vif.type in ieee80211_get_buffered_bc before. As the later commit intended to fix the MESH case, fix it by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN. Fixes: 7cbf9d01 ("mac80211: fix oops on mesh PS broadcast forwarding") Signed-off-by:
Michael Braun <michael-dev@fami-braun.de> Signed-off-by:
-
Emmanuel Grumbach authored
commit 82e5a649 upstream. There is a flow in which we send the host command in SYNC mode, but we don't take priv->mutex. Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Dan Williams authored
commit 8a4aeec8 upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by:
Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Rafał Miłecki authored
commit 12cd43c6 upstream. Register B43_MMIO_PSM_PHY_HDR is 16 bit one, so accessing it with 32b functions isn't safe. On my machine it causes delayed (!) CPU exception: Disabling lock debugging due to kernel taint mce: [Hardware Error]: CPU 0: Machine Check Exception: 4 Bank 4: b200000000070f0f mce: [Hardware Error]: TSC 164083803dc mce: [Hardware Error]: PROCESSOR 2:20fc2 TIME 1396650505 SOCKET 0 APIC 0 microcode 0 mce: [Hardware Error]: Run the above through 'mcelog --ascii' mce: [Hardware Error]: Machine check: Processor context corrupt Kernel panic - not syncing: Fatal machine check on current CPU Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Acked-by:
-
Mikulas Patocka authored
commit 43751a1b upstream. This patch fixes the hardware cursor on mach64 when font width is not a multiple of 8 pixels. If you load such a font, the cursor is expanded to the next 8-byte boundary and a part of the next character after the cursor is not visible. For example, when you load a font with 12-pixel width, the cursor width is 16 pixels and when the cursor is displayed, 4 pixels of the next character are not visible. The reason is this: atyfb_cursor is called with proper parameters to load an image that is 12-pixel wide. However, the number is aligned on the next 8-pixel boundary on the line "unsigned int width = (cursor->image.width + 7) >> 3;" and the whole function acts as it is was loading a 16-pixel image. This patch fixes it so that the value written to the framebuffer is padded with 0xaaaa (the transparent pattern) when the image size it not a multiple of 8 pixels. The transparent pattern causes that the cursor will not interfere with the next character. Signed-off-by:
-
Mikulas Patocka authored
commit c29dd869 upstream. This patch fixes mach64 to use unaligned access to the font bitmap. This fixes unaligned access warning on sparc64 when 14x8 font is loaded. On x86(64), unaligned access is handled in hardware, so both functions le32_to_cpup and get_unaligned_le32 perform the same operation. On RISC machines, unaligned access is not handled in hardware, so we better use get_unaligned_le32 to avoid the unaligned trap and warning. Signed-off-by:
-
Mikulas Patocka authored
commit a772d473 upstream. When X11 is running and the user switches back to console, the card modifies the content of registers M_MACCESS and M_PITCH in periodic intervals. This patch fixes it by restoring the content of these registers before issuing any accelerator command. Signed-off-by:
-
