The IRQ_* macros need to be made visible via the mach/irqs.h file but
without the additional macros defined in the board-*.h files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

_sdata and __bss_stop are common symbols defined by many architectures
and made available to the kernel via asm-generic/sections.h. Kmemleak
uses these symbols when scanning the data sections.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch adds a comment to the proc-v7.S file for the setting of the
PRRR and NMRR registers. It also sets the PRRR[13:12] bits to 0
(corresponding to the reserved TEX[0]CB encoding 110) to be consistent
with the documentation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The SWP instruction has been deprecated starting with the ARMv6
architecture. On ARMv7 processors with the multiprocessor extensions
(like Cortex-A9), this instruction is disabled by default but it can be
enabled by setting bit 10 in the System Control register. Note that
setting this bit is safe even if the ARMv7 processor has the SWP
instruction enabled by default.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

If a process is interrupted during an If-Then block and a signal is
invoked, the ITSTATE bits must be cleared otherwise the handler would
not run correctly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Joseph S. Myers <joseph@codesourcery.com>

There are additional bits to set for the ARMv7 SMP extensions in the
TTBR registers. The IRGN bits order is counter-intuitive but it allows
software built for the ARMv7 base architecture to run on an
implementation with the MP extensions.
Signed-off-by: Tony Thompson <Anthony.Thompson@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

ARMv7 SMP hardware can handle the TLB maintenance operations
broadcasting in hardware so that the software can avoid the costly IPIs.
This patch adds the necessary checks (the MMFR3 CPUID register) to avoid
the broadcasting if already supported by the hardware.

(this patch is based on the work done by Tony Thompson @ ARM)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

If CONFIG_LEDS is enabled, it makes more sense to toggle one LED per CPU
in SMP systems rather than a single LED for all the CPUs.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Signed-off-by: Colin Tuckley <Colin.Tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch adds a Kconfig option for specifying whether Linux will only
be run in secure mode on the RealView PB1176 platform. Enabling it will
make the secure flash memory block (64MB @ 0x3c000000) available to
Linux.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This is a RealView platform supporting core tiles with ARM11MPCore,
Cortex-A8 or Cortex-A9 (multicore) processors. It has support for MMC,
CompactFlash, PCI-E.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt2sas: fix driver version inconsistency
  [SCSI] 3w-xxxx: scsi_dma_unmap fix
  [SCSI] 3w-9xxx: scsi_dma_unmap fix
  [SCSI] ses: fix problems caused by empty SES provided name
  [SCSI] fc-transport: Close state transition-window during rport deletion.
  [SCSI] initialize max_target_blocked in scsi_alloc_target
  [SCSI] fnic: Add new Cisco PCI-Express FCoE HBA

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Avoid open on possible directories since Samba now rejects them

Small change (mostly formatting) to limit lookup based open calls to
file create only.

After discussion yesteday on samba-technical about the posix lookup
regression,  and looking at a problem with cifs posix open to one
particular Samba version, Jeff and JRA realized that Samba server's
behavior changed in this area (posix open behavior on files vs.
directories).   To make this behavior consistent, JRA just made a
fix to Samba server to alter how it handles open of directories (now
returning the equivalent of EISDIR instead of success). Since we don't
know at lookup time whether the inode is a directory or file (and
thus whether posix open will succeed with most current Samba server),
this change avoids the posix open code on lookup open (just issues
posix open on creates).    This gets the semantic benefits we want
(atomicity, posix byte range locks, improved write semantics on newly
created files) and file create still is fast, and we avoid the problem
that Jeff noticed yesterday with "openat" (and some open directory
calls) of non-cached directories to one version of Samba server, and
will work with future Samba versions (which include the fix jra just
pushed into Samba server).  I confirmed this approach with jra
yesterday and with Shirish today.

Posix open is only called (at lookup time) for file create now.
For opens (rather than creates), because we do not know if it
is a file or directory yet, and current Samba no longer allows
us to do posix open on dirs, we could end up wasting an open call
on what turns out to be a dir. For file opens, we wait to call posix
open till cifs_open.  It could be added here (lookup) in the future
but the performance tradeoff of the extra network request when EISDIR
or EACCES is returned would have to be weighed against the 50%
reduction in network traffic in the other paths.
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
CC: Jeremy Allison <jra@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:

  Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6d33
  Faulting instruction address: 0xc000000000246b80
  Oops: Kernel access of bad area, sig: 11 [#1]
  ....
  [c000000012d436a0] [c0000000001002d0] .kfree+0x120/0x34c (unreliable)
  [c000000012d43730] [c000000000246d60] .pci_release_selected_regions+0x3c/0x68
  [c000000012d437c0] [d000000002d54700] .icom_kref_release+0xf4/0x118 [icom]
  [c000000012d43850] [c000000000232e50] .kref_put+0x74/0x94
  [c000000012d438d0] [d000000002d56c58] .icom_remove+0x40/0xa4 [icom]
  [c000000012d43960] [c000000000249e48] .pci_device_remove+0x50/0x90
  [c000000012d439e0] [c0000000002d68d8] .__device_release_driver+0x94/0xd4
  [c000000012d43a70] [c0000000002d7104] .driver_detach+0xf8/0x12c
  [c000000012d43b00] [c0000000002d549c] .bus_remove_driver+0xbc/0x11c
  [c000000012d43b90] [c0000000002d71dc] .driver_unregister+0x60/0x80
  [c000000012d43c20] [c00000000024a07c] .pci_unregister_driver+0x44/0xe8
  [c000000012d43cb0] [d000000002d56bf4] .icom_exit+0x1c/0x40 [icom]
  [c000000012d43d30] [c000000000095fa8] .SyS_delete_module+0x214/0x2a8
  [c000000012d43e30] [c00000000000852c] syscall_exit+0x0/0x40
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: stable@kernel.org
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
  ALSA: hda - fix audio on HP TX25xx series notebooks
  ALSA: pcsp - fix printk format warning again

* fix/misc:
  ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
  ALSA: pcsp - fix printk format warning again

ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix memory leak in nilfs_ioctl_clean_segments

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  via82cxxx: Add VIA VX855 PCI Device ID
  ide: report timeouts in ide_busy_sleep()
  ide: improve failed opcode reporting
  ide: fix printk() levels in ide_dump_ata[pi]_error()
  ide: fix OOPS during ide-cd error recovery
  ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] fix posix open regression

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
  MIPS: IP32: Fix build error due to uninitialized variable.
  MIPS: Fix sparse warning in incompatiable argument type of clear_user.

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/maple: Add a quirk to disable MSI for IPR on Bimini

* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  video: stop sh_mobile_lcdcfb only if started
  sh: ap325 camera without i2c driver fix

Instead of queuing IPMB messages before channel initialization, just
throw them away.  Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.

Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.

This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* change 'hwif' argument to 'drive'
* report an error on timeout
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.

Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fixes "<3>" in error messages like this one:

hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:

>   hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
>   ide: failed opcode was: unknown
>   hdc: DMA disabled
>   ------------[ cut here ]------------
>   kernel BUG at drivers/ide/ide-io.c:872!

It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances.  Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.

Fixes bug #13345:

	http://bugzilla.kernel.org/show_bug.cgi?id=13345Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:

  commit 8588a2b7
  ("ide: add SH-S202J to ivb_list[]")

We also later added support for more such devices in:

  commit e97564f3
  ("ide: More TSST drives with broken cable detection")

and in:

  commit 3ced5c49
  ("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")

It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.

v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

They are unneeded and as the issue fixed in lmo commit
63f7ec59053e3f850ab67a9938e631bcba64c6ce shows even harmful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

  CC      arch/mips/sgi-ip32/ip32-reset.o
cc1: warnings being treated as errors
arch/mips/sgi-ip32/ip32-reset.c: In function 'debounce':
arch/mips/sgi-ip32/ip32-reset.c:97: error: 'reg_a' is used uninitialized in this function

The issues is old but due to the volatile keyword gcc older than 4.4 did
not warn about this obvious bug.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The type of the second argument of access_ok should be (void __user *).
The unnecessary conversion of the clear_user address argument was causing
sparse to emit warnings on the __chk_user_ptr check.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes a new memory leak problem in garbage collection.  The
problem was brought by the bugfix patch ("nilfs2: fix lock order
reversal in nilfs_clean_segments ioctl").

Thanks to Kentaro Suzuki for finding this problem.
Reported-by: Kentaro Suzuki <k_suzuki@ms.sylc.co.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

* fix/hda:
  ALSA: hda - fix audio on HP TX25xx series notebooks

Fixes https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4121

Taken from https://bugzilla.redhat.com/show_bug.cgi?id=498060Signed-off-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Something in the HW or FW setup is busted and MSIs aren't working with
IPR on Bimini, so until we figure out exaxtly what's up, we quirk them
out
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>