- 19 Jun, 2015 40 commits
-
-
Max Mansfield authored
commit c7d373c3 upstream. This patch integrates Cyber Cortex AV boards with the existing ftdi_jtag_quirk in order to use serial port 0 with JTAG which is required by the manufacturers' software. Steps: 2 [ftdi_sio_ids.h] 1. Defined the device PID [ftdi_sio.c] 2. Added a macro declaration to the ids array, in order to enable the jtag quirk for the device. Signed-off-by:
Max Mansfield <max.m.mansfield@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Trond Myklebust authored
commit 7c0af9ff upstream. put_rpccred() can sleep. Fixes: 8f649c37 ("NFSv4: Fix the locking in nfs_inode_reclaim_delegation()") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Michiel vd Garde authored
commit 675af708 upstream. These device ID's are not associated with the cp210x module currently, but should be. This patch allows the devices to operate upon connecting them to the usb bus as intended. Signed-off-by:
Michiel van de Garde <mgparser@gmail.com> Signed-off-by:
-
Jouni Malinen authored
commit 9c1c98a3 upstream. The current minstrel_ht rate control behavior is somewhat optimistic in trying to find optimum TX rate. While this is usually fine for normal Data frames, there are cases where a more conservative set of retry parameters would be beneficial to make the connection more robust. EAPOL frames are critical to the authentication and especially the EAPOL-Key message 4/4 (the last message in the 4-way handshake) is important to get through to the AP. If that message is lost, the only recovery mechanism in many cases is to reassociate with the AP and start from scratch. This can often be avoided by trying to send the frame with more conservative rate and/or with more link layer retries. In most cases, minstrel_ht is currently using the initial EAPOL-Key frames for probing higher rates and this results in only five link layer transmission attempts (one at high(ish) MCS and four at MCS0). While this works with most APs, it looks like there are some deployed APs that may have issues with the EAPOL frames using HT MCS immediately after association. Similarly, there may be issues in cases where the signal strength or radio environment is not good enough to be able to get frames through even at couple of MCS 0 tries. The best approach for this would likely to be to reduce the TX rate for the last rate (3rd rate parameter in the set) to a low basic rate (say, 6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly requires some more effort. For now, we can start with a simple one-liner that forces the minimum rate to be used for EAPOL frames similarly how the TX rate is selected for the IEEE 802.11 Management frames. This does result in a small extra latency added to the cases where the AP would be able to receive the higher rate, but taken into account how small number of EAPOL frames are used, this is likely to be insignificant. A future optimization in the minstrel_ht design can also allow this patch to be reverted to get back to the more optimized initial TX rate. It should also be noted that many drivers that do not use minstrel as the rate control algorithm are already doing similar workarounds by forcing the lowest TX rate to be used for EAPOL frames. Reported-by:
Linus Torvalds <torvalds@linux-foundation.org> Tested-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [lizf: Backported to 3.4: adjust the if statement] Signed-off-by:
-
Johan Hovold authored
commit ca4383a3 upstream. Add missing error handling when registering the tty device at port probe. This avoids trying to remove an uninitialised character device when the port device is removed. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <greg@kroah.com> [lizf: Backported to 3.4: - adjust context - s/goto exit_with_autopm/goto exit] Signed-off-by:
-
Johan Hovold authored
commit 07fdfc5e upstream. Fix return value in probe error path, which could end up returning success (0) on errors. This could in turn lead to use-after-free or double free (e.g. in port_remove) when the port device is removed. Fixes: c706ebdf ("USB: usb-serial: call port_probe and port_remove at the right times") Signed-off-by:
-
Mark Glover authored
commit f6950344 upstream. These product identifiers (PID) all deal with marine NMEA format data used on motor boats and yachts. We supply the programmed devices to Chetco, for use inside their equipment. The PIDs are a direct copy of our Windows device drivers (FTDI drivers with altered PIDs). Signed-off-by:
Mark Glover <mark@actisense.com> [johan: edit commit message slightly ] Signed-off-by:
-
Alan Stern authored
commit f0c2b681 upstream. When a signal is delivered, the information in the siginfo structure is copied to userspace. Good security practice dicatates that the unused fields in this structure should be initialized to 0 so that random kernel stack data isn't exposed to the user. This patch adds such an initialization to the two places where usbfs raises signals. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Dave Mielke <dave@mielke.cc> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Mathias Nyman authored
commit 6596a926 upstream. Include the high order bit fields for Max scratchpad buffers when calculating how many scratchpad buffers are needed. I'm suprised this hasn't caused more issues, we never allocated more than 32 buffers even if xhci needed more. Either we got lucky and xhci never really used past that area, or then we got enough zeroed dma memory anyway. Should be backported as far back as possible Reported-by:
Tim Chen <tim.c.chen@linux.intel.com> Tested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Paolo Bonzini authored
commit 4ff6f8e6 upstream. This has been broken for a long time: it broke first in 2.6.35, then was almost fixed in 2.6.36 but this one-liner slipped through the cracks. The bug shows up as an infinite loop in Windows 7 (and newer) boot on 32-bit hosts without EPT. Windows uses CMPXCHG8B to write to page tables, which causes a page fault if running without EPT; the emulator is then called from kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are not 0; the common case for this is that the NX bit (bit 63) is 1. Fixes: 6550e1f1 Fixes: 16518d5aReported-by:
Erik Rull <erik.rull@rdsoftware.de> Tested-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Jiri Pirko authored
commit 57e59563 upstream. Currently following race is possible in team: CPU0 CPU1 team_port_del team_upper_dev_unlink priv_flags &= ~IFF_TEAM_PORT team_handle_frame team_port_get_rcu team_port_exists priv_flags & IFF_TEAM_PORT == 0 return NULL (instead of port got from rx_handler_data) netdev_rx_handler_unregister The thing is that the flag is removed before rx_handler is unregistered. If team_handle_frame is called in between, team_port_exists returns 0 and team_port_get_rcu will return NULL. So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister that team_handle_frame will always see valid rx_handler_data pointer. Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Fixes: 3d249d4c ("net: introduce ethernet teaming device") Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
commit 78296c97 upstream. As soon as extract_icmp6_fields() returns, its local storage (automatic variables) is deallocated and can be overwritten. Lets add an additional parameter to make sure storage is valid long enough. While we are at it, adds some const qualifiers. Signed-off-by:
Eric Dumazet <edumazet@google.com> Fixes: b64c9256 ("tproxy: added IPv6 support to the socket match") Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Ryusuke Konishi authored
commit 957ed60b upstream. Each inode of nilfs2 stores a root node of a b-tree, and it turned out to have a memory overrun issue: Each b-tree node of nilfs2 stores a set of key-value pairs and the number of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as a few other "bn_*" members. Since the value of "bn_nchildren" is used for operations on the key-values within the b-tree node, it can cause memory access overrun if a large number is incorrectly set to "bn_nchildren". For instance, nilfs_btree_node_lookup() function determines the range of binary search with it, and too large "bn_nchildren" leads nilfs_btree_node_get_key() in that function to overrun. As for intermediate b-tree nodes, this is prevented by a sanity check performed when each node is read from a drive, however, no sanity check has been done for root nodes stored in inodes. This patch fixes the issue by adding missing sanity check against b-tree root nodes so that it's called when on-memory inodes are read from ifile, inode metadata file. Signed-off-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Takashi Iwai authored
commit 70372a75 upstream. When a PCM draining is performed to an empty stream that has been already in PREPARED state, the current code just ignores and leaves as it is, although the drain is supposed to set all such streams to SETUP state. This patch covers that overlooked case. Signed-off-by:
-
Nicolas Saenz Julienne authored
commit 2f97c20e upstream. The gpio_chip operations receive a pointer the gpio_chip struct which is contained in the driver's private struct, yet the container_of call in those functions point to the mfd struct defined in include/linux/mfd/tps65912.h. Signed-off-by:
Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Al Viro authored
commit 0a280962 upstream. X-Coverup: just ask spender Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 0db59e59 upstream. As it is, we have debugfs_remove() racing with symlink traversals. Supply ->evict_inode() and do freeing there - inode will remain pinned until we are done with the symlink body. And rip the idiocy with checking if dentry is positive right after we'd verified debugfs_positive(), which is a stronger check... Signed-off-by:
-
Jay Lan authored
commit 14675592 upstream. The output of KDB 'summary' command should report MemTotal, MemFree and Buffers output in kB. Current codes report in unit of pages. A define of K(x) as is defined in the code, but not used. This patch would apply the define to convert the values to kB. Please include me on Cc on replies. I do not subscribe to linux-kernel. Signed-off-by:
Jay Lan <jlan@sgi.com> Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
Mikulas Patocka authored
commit 22aa66a3 upstream. When the snapshot target is unloaded, snapshot_dtr() waits until pending_exceptions_count drops to zero. Then, it destroys the snapshot. Therefore, the function that decrements pending_exceptions_count should not touch the snapshot structure after the decrement. pending_complete() calls free_pending_exception(), which decrements pending_exceptions_count, and then it performs up_write(&s->lock) and it calls retry_origin_bios() which dereferences s->origin. These two memory accesses to the fields of the snapshot may touch the dm_snapshot struture after it is freed. This patch moves the call to free_pending_exception() to the end of pending_complete(), so that the snapshot will not be destroyed while pending_complete() is in progress. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit 2bec1f4a upstream. The function dm_get_md finds a device mapper device with a given dev_t, increases the reference count and returns the pointer. dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the device, tests that the device doesn't have DMF_DELETING or DMF_FREEING flag, drops _minor_lock and returns pointer to the device. dm_get_md then calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag, otherwise it increments the reference count. There is a possible race condition - after dm_find_md exits and before dm_get is called, there are no locks held, so the device may disappear or DMF_FREEING flag may be set, which results in BUG. To fix this bug, we need to call dm_get while we hold _minor_lock. This patch renames dm_find_md to dm_get_md and changes it so that it calls dm_get while holding the lock. Signed-off-by:
-
Mitko Haralanov authored
commit 18c0b82a upstream. This changeset removes all the code that allows the driver to write to the EEPROM and update the recorded error counters and power on hours. These two stats are unused and writing them exposes a timing risk which could leave the EEPROM in a bad state preventing further normal operation of the HCA. Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Tony Battersby authored
commit 3b524a68 upstream. Fix SCSI generic read() incorrectly returning success after detecting an error. Signed-off-by:
Tony Battersby <tonyb@cybernetics.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Minh Duc Tran authored
fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit. commit f76a610a upstream. In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141 Assert is seen with AMD cpu whenever calling pci_alloc_consistent. [ 29.406183] ------------[ cut here ]------------ [ 29.410505] kernel BUG at lib/iommu-helper.c:13! Signed-off-by:
Minh Tran <minh.tran@emulex.com> Fixes: 6733b39aSigned-off-by:
-
Martin KaFai Lau authored
commit 3b471175 upstream. ipv6_cow_metrics() currently assumes only DST_HOST routes require dynamic metrics allocation from inetpeer. The assumption breaks when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric. Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set() is called after the route is created. This patch creates the metrics array (by calling dst_cow_metrics_generic) in ipv6_cow_metrics(). Test: radvd.conf: interface qemubr0 { AdvLinkMTU 1300; AdvCurHopLimit 30; prefix fd00:face:face:face::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; }; Before: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec fe80::/64 dev eth0 proto kernel metric 256 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec After: [root@qemu1 ~]# ip -6 r show | egrep -v unreachable fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300 fe80::/64 dev eth0 proto kernel metric 256 mtu 1300 default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30 Fixes: 8e2ec639 (ipv6: don't use inetpeer to store metrics for routes.) Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Darrick J. Wong authored
commit 37527b86 upstream. I created a dm-raid1 device backed by a device that supports DISCARD and another device that does NOT support DISCARD with the following dm configuration: # echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo # lsblk -D NAME DISC-ALN DISC-GRAN DISC-MAX DISC-ZERO sda 0 4K 1G 0 `-moo (dm-0) 0 4K 1G 0 sdb 0 0B 0B 0 `-moo (dm-0) 0 4K 1G 0 Notice that the mirror device /dev/mapper/moo advertises DISCARD support even though one of the mirror halves doesn't. If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite loop in do_region() when it tries to issue a DISCARD request to sdb. The problem is that when we call do_region() against sdb, num_sectors is set to zero because q->limits.max_discard_sectors is zero. Therefore, "remaining" never decreases and the loop never terminates. To fix this: before entering the loop, check for the combination of REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up the mirror device. This bug was found by the unfortunate coincidence of pvmove and a discard operation in the RHEL 6.5 kernel; upstream is also affected. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Acked-by:
"Martin K. Petersen" <martin.petersen@oracle.com> Signed-off-by:
-
Mikulas Patocka authored
commit f2ed51ac upstream. It may be possible that a device claims discard support but it rejects discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3 filesystem driven by the ext4 driver. It may also happen if the underlying devices are moved from one disk on another. If discard error happens, we reject the bio with -EOPNOTSUPP, but we do not degrade the array. This patch fixes failed test shell/lvconvert-repair-transient.sh in the lvm2 testsuite if the testsuite is extracted on an ext2 or ext3 filesystem and it is being driven by the ext4 driver. Signed-off-by:
-
Chen Jie authored
commit 164c2406 upstream. sm->offset maybe wrong but magic maybe right, the offset do not have CRC. Badness at c00c7580 [verbose debug info unavailable] NIP: c00c7580 LR: c00c718c CTR: 00000014 REGS: df07bb40 TRAP: 0700 Not tainted (2.6.34.13-WR4.3.0.0_standard) MSR: 00029000 <EE,ME,CE> CR: 22084f84 XER: 00000000 TASK = df84d6e0[908] 'mount' THREAD: df07a000 GPR00: 00000001 df07bbf0 df84d6e0 00000000 00000001 00000000 df07bb58 00000041 GPR08: 00000041 c0638860 00000000 00000010 22084f88 100636c8 df814ff8 00000000 GPR16: df84d6e0 dfa558cc c05adb90 00000048 c0452d30 00000000 000240d0 000040d0 GPR24: 00000014 c05ae734 c05be2e0 00000000 00000001 00000000 00000000 c05ae730 NIP [c00c7580] __alloc_pages_nodemask+0x4d0/0x638 LR [c00c718c] __alloc_pages_nodemask+0xdc/0x638 Call Trace: [df07bbf0] [c00c718c] __alloc_pages_nodemask+0xdc/0x638 (unreliable) [df07bc90] [c00c7708] __get_free_pages+0x20/0x48 [df07bca0] [c00f4a40] __kmalloc+0x15c/0x1ec [df07bcd0] [c01fc880] jffs2_scan_medium+0xa58/0x14d0 [df07bd70] [c01ff38c] jffs2_do_mount_fs+0x1f4/0x6b4 [df07bdb0] [c020144c] jffs2_do_fill_super+0xa8/0x260 [df07bdd0] [c020230c] jffs2_fill_super+0x104/0x184 [df07be00] [c0335814] get_sb_mtd_aux+0x9c/0xec [df07be20] [c033596c] get_sb_mtd+0x84/0x1e8 [df07be60] [c0201ed0] jffs2_get_sb+0x1c/0x2c [df07be70] [c0103898] vfs_kern_mount+0x78/0x1e8 [df07bea0] [c0103a58] do_kern_mount+0x40/0x100 [df07bec0] [c011fe90] do_mount+0x240/0x890 [df07bf10] [c0120570] sys_mount+0x90/0xd8 [df07bf40] [c00110d8] ret_from_syscall+0x0/0x4 === Exception: c01 at 0xff61a34 LR = 0x100135f0 Instruction dump: 38800005 38600000 48010f41 4bfffe1c 4bfc2d15 4bfffe8c 72e90200 4082fc28 3d20c064 39298860 8809000d 68000001 <0f000000> 2f800000 419efc0c 38000001 mount: mounting /dev/mtdblock3 on /common failed: Input/output error Signed-off-by:
Chen Jie <chenjie6@huawei.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Adrian Knoth authored
commit f0153c3d upstream. RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period sizes of 32-4096, this translates to 4-512 periods. The older RME cards have a variable buffer size but require exactly two periods. This patch enforces nperiods=2 on those cards. Signed-off-by:
Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by:
-
Alex Deucher authored
commit 66c2b84b upstream. Don't restrict it to just eDP panels. Some LVDS bridge chips require this. Fixes blank panels on resume on certain laptops. Noticed by mrnuke on IRC. bug: https://bugs.freedesktop.org/show_bug.cgi?id=42960Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Grazvydas Ignotas authored
commit 9cb12d7b upstream. For whatever reason, generic_access_phys() only remaps one page, but actually allows to access arbitrary size. It's quite easy to trigger large reads, like printing out large structure with gdb, which leads to a crash. Fix it by remapping correct size. Fixes: 28b2ee20 ("access_process_vm device memory infrastructure") Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 3fd7b60f upstream. This patch drops legacy active_ts_list usage within iscsi_target_tq.c code. It was originally used to track the active thread sets during iscsi-target shutdown, and is no longer used by modern upstream code. Two people have reported list corruption using traditional iscsi-target and iser-target with the following backtrace, that appears to be related to iscsi_thread_set->ts_list being used across both active_ts_list and inactive_ts_list. [ 60.782534] ------------[ cut here ]------------ [ 60.782543] WARNING: CPU: 0 PID: 9430 at lib/list_debug.c:53 __list_del_entry+0x63/0xd0() [ 60.782545] list_del corruption, ffff88045b00d180->next is LIST_POISON1 (dead000000100100) [ 60.782546] Modules linked in: ib_srpt tcm_qla2xxx qla2xxx tcm_loop tcm_fc libfc scsi_transport_fc scsi_tgt ib_isert rdma_cm iw_cm ib_addr iscsi_target_mod target_core_pscsi target_core_file target_core_iblock target_core_mod configfs ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables bridge stp llc autofs4 sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ib_ipoib ib_cm ib_uverbs ib_umad mlx4_en mlx4_ib ib_sa ib_mad ib_core mlx4_core dm_mirror dm_region_hash dm_log dm_mod vhost_net macvtap macvlan vhost tun kvm_intel kvm uinput iTCO_wdt iTCO_vendor_support microcode serio_raw pcspkr sb_edac edac_core sg i2c_i801 lpc_ich mfd_core mtip32xx igb i2c_algo_bit i2c_core ptp pps_core ioatdma dca wmi ext3(F) jbd(F) mbcache(F) sd_mod(F) crc_t10dif(F) crct10dif_common(F) ahci(F) libahci(F) isci(F) libsas(F) scsi_transport_sas(F) [last unloaded: speedstep_lib] [ 60.782597] CPU: 0 PID: 9430 Comm: iscsi_ttx Tainted: GF 3.12.19+ #2 [ 60.782598] Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013 [ 60.782599] 0000000000000035 ffff88044de31d08 ffffffff81553ae7 0000000000000035 [ 60.782602] ffff88044de31d58 ffff88044de31d48 ffffffff8104d1cc 0000000000000002 [ 60.782605] ffff88045b00d180 ffff88045b00d0c0 ffff88045b00d0c0 ffff88044de31e58 [ 60.782607] Call Trace: [ 60.782611] [<ffffffff81553ae7>] dump_stack+0x49/0x62 [ 60.782615] [<ffffffff8104d1cc>] warn_slowpath_common+0x8c/0xc0 [ 60.782618] [<ffffffff8104d2b6>] warn_slowpath_fmt+0x46/0x50 [ 60.782620] [<ffffffff81280933>] __list_del_entry+0x63/0xd0 [ 60.782622] [<ffffffff812809b1>] list_del+0x11/0x40 [ 60.782630] [<ffffffffa06e7cf9>] iscsi_del_ts_from_active_list+0x29/0x50 [iscsi_target_mod] [ 60.782635] [<ffffffffa06e87b1>] iscsi_tx_thread_pre_handler+0xa1/0x180 [iscsi_target_mod] [ 60.782642] [<ffffffffa06fb9ae>] iscsi_target_tx_thread+0x4e/0x220 [iscsi_target_mod] [ 60.782647] [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod] [ 60.782652] [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod] [ 60.782655] [<ffffffff8106f99e>] kthread+0xce/0xe0 [ 60.782657] [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70 [ 60.782660] [<ffffffff8156026c>] ret_from_fork+0x7c/0xb0 [ 60.782662] [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70 [ 60.782663] ---[ end trace 9662f4a661d33965 ]--- Since this code is no longer used, go ahead and drop the problematic usage all-together. Reported-by:
Gavin Guo <gavin.guo@canonical.com> Reported-by:
Moussa Ba <moussaba@micron.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Roman Gushchin authored
commit 8138a67a upstream. I noticed that "allowed" can easily overflow by falling below 0, because (total_vm / 32) can be larger than "allowed". The problem occurs in OVERCOMMIT_NONE mode. In this case, a huge allocation can success and overcommit the system (despite OVERCOMMIT_NONE mode). All subsequent allocations will fall (system-wide), so system become unusable. The problem was masked out by commit c9b1d098 ("mm: limit growth of 3% hardcoded other user reserve"), but it's easy to reproduce it on older kernels: 1) set overcommit_memory sysctl to 2 2) mmap() large file multiple times (with VM_SHARED flag) 3) try to malloc() large amount of memory It also can be reproduced on newer kernels, but miss-configured sysctl_user_reserve_kbytes is required. Fix this issue by switching to signed arithmetic here. Signed-off-by:
Roman Gushchin <klamm@yandex-team.ru> Cc: Andrew Shewmaker <agshew@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Roman Gushchin authored
commit 5703b087 upstream. I noticed, that "allowed" can easily overflow by falling below 0, because (total_vm / 32) can be larger than "allowed". The problem occurs in OVERCOMMIT_NONE mode. In this case, a huge allocation can success and overcommit the system (despite OVERCOMMIT_NONE mode). All subsequent allocations will fall (system-wide), so system become unusable. The problem was masked out by commit c9b1d098 ("mm: limit growth of 3% hardcoded other user reserve"), but it's easy to reproduce it on older kernels: 1) set overcommit_memory sysctl to 2 2) mmap() large file multiple times (with VM_SHARED flag) 3) try to malloc() large amount of memory It also can be reproduced on newer kernels, but miss-configured sysctl_user_reserve_kbytes is required. Fix this issue by switching to signed arithmetic here. [akpm@linux-foundation.org: use min_t] Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Naoya Horiguchi authored
commit 9fbc1f63 upstream. If __unmap_hugepage_range() tries to unmap the address range over which hugepage migration is on the way, we get the wrong page because pte_page() doesn't work for migration entries. This patch simply clears the pte for migration entries as we do for hwpoison entries. Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Steve Capper <steve.capper@linaro.org> Signed-off-by:
-
Naoya Horiguchi authored
commit a8bda28d upstream. There is a race condition between hugepage migration and change_protection(), where hugetlb_change_protection() doesn't care about migration entries and wrongly overwrites them. That causes unexpected results like kernel crash. HWPoison entries also can cause the same problem. This patch adds is_hugetlb_entry_(migration|hwpoisoned) check in this function to do proper actions. Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
-
Naoya Horiguchi authored
commit 0f792cf9 upstream. When running the test which causes the race as shown in the previous patch, we can hit the BUG "get_page() on refcount 0 page" in hugetlb_fault(). This race happens when pte turns into migration entry just after the first check of is_hugetlb_entry_migration() in hugetlb_fault() passed with false. To fix this, we need to check pte_present() again after huge_ptep_get(). This patch also reorders taking ptl and doing pte_page(), because pte_page() should be done in ptl. Due to this reordering, we need use trylock_page() in page != pagecache_page case to respect locking order. Fixes: 66aebce7 ("hugetlb: fix race condition in hugetlb_fault()") Signed-off-by:
-
Mikulas Patocka authored
commit d4d4eda2 upstream. On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the speedstep-smi driver sometimes loads and sometimes doesn't load with "change to state X failed" message. The hardware sometimes refuses to change frequency and in this case, we need to retry later. I found out that we need to enable interrupts while waiting. When we enable interrupts, the hardware blockage that prevents frequency transition resolves and the transition is possible. With disabled interrupts, the blockage doesn't resolve (no matter how long do we wait). The exact reasons for this hardware behavior are unknown. This patch enables interrupts in the function speedstep_set_state that can be called with disabled interrupts. However, this function is called with disabled interrupts only from speedstep_get_freqs, so it shouldn't cause any problem. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Trond Myklebust authored
commit d8ba1f97 upstream. If the call to decode_rc_list() fails due to a memory allocation error, then we need to truncate the array size to ensure that we only call kfree() on those pointer that were allocated. Reported-by:
David Ramos <daramos@stanford.edu> Fixes: 4aece6a1 ("nfs41: cb_sequence xdr implementation") Signed-off-by:
-
Jan Kara authored
commit 6ee8e25f upstream. Commit e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") broke handling of renames in audit. Audit code wants to update inode number of an inode corresponding to watched name in a directory. When something gets renamed into a directory to a watched name, inotify previously passed moved inode to audit code however new fsnotify code passes directory inode where the change happened. That confuses audit and it starts watching parent directory instead of a file in a directory. This can be observed for example by doing: cd /tmp touch foo bar auditctl -w /tmp/foo touch foo mv bar foo touch foo In audit log we see events like: type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1 ... type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE ... and that's it - we see event for the first touch after creating the audit rule, we see events for rename but we don't see any event for the last touch. However we start seeing events for unrelated stuff happening in /tmp. Fix the problem by passing moved inode as data in the FS_MOVED_FROM and FS_MOVED_TO events instead of the directory where the change happens. This doesn't introduce any new problems because noone besides audit_watch.c cares about the passed value: fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events. fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all. fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH. kernel/audit_tree.c doesn't care about passed 'data' at all. kernel/audit_watch.c expects moved inode as 'data'. Fixes: e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
-
Dan Carpenter authored
commit e4940626 upstream. The problem here is that we check: if (dev >= SNDRV_CARDS) Then we increment "dev". if (!joystick_port[dev++]) Then we use it as an offset into a array with SNDRV_CARDS elements. if (!request_region(joystick_port[dev], 8, "Riptide gameport")) { This has 3 effects: 1) If you use the module option to specify the joystick port then it has to be shifted one space over. 2) The wrong error message will be printed on failure if you have over 32 cards. 3) Static checkers will correctly complain that are off by one. Fixes: db1005ec ('ALSA: riptide - Fix joystick resource handling') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
