- 17 Oct, 2022 40 commits
-
-
Matti Lehtimäki authored
Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T530) wifi tablet based on the apq8026 platform. Currently supported are accelerometer sensor, hall sensor, internal storage, physical buttons (power & volume), screen (based on simple-framebuffer set up by the bootloader), sdcard, touchscreen and USB. Signed-off-by:
Matti Lehtimäki <matti.lehtimaki@gmail.com> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220927214940.244480-4-matti.lehtimaki@gmail.com
-
Matti Lehtimäki authored
Add binding documentation for Samsung Galaxy Tab 4 10.1 (2014) wifi tablet which is based on Snapdragon 400 (apq8026) SoC. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Matti Lehtimäki authored
The PM8226 provides 8 GPIOs. Add a node to support them. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Acked-by:
-
Luca Weiss authored
All other usages of qcom,spmi-gpio use the gpio@ node name, and this is also validated by the dt binding check. Fix it. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Luca Weiss authored
The name rgb-led is not allowed, multi-led is supposed to be used. <snip>/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dtb: pm8941@1: pwm: 'rgb-led' does not match any of the regexes: '^led@[0-9a-f]$', 'pinctrl-[0-9]+' From schema: <snip>/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml Signed-off-by: -
Luca Weiss authored
The bindings check complains that #address-cells and #size-cells shouldn't be in the smd-edge node. Remove it. Signed-off-by:
-
Luca Weiss authored
Add the interrupt for tsens, based on the information from downstream msm-3.4 dts. Signed-off-by:
-
Luca Weiss authored
Bindings mandate the use of the fallback compatible qcom,tsens-v0_1 for msm8974. Add it to fix the warning. Signed-off-by:
-
Luca Weiss authored
Add the chassis-type property to arm32 Qualcomm watches, phones and tablets. Signed-off-by:
-
Luca Weiss authored
Adjust the name to match the bindings and fix the following validation error: <snip>/arch/arm/boot/dts/qcom-apq8026-huawei-sturgeon.dtb: memory@fc428000: $nodename:0: 'memory@fc428000' does not match '^sram(@.*)?' From schema: <snip>/Documentation/devicetree/bindings/sram/sram.yaml Signed-off-by: -
Dmitry Baryshkov authored
Change DSI PHY node names from custom 'dsi-phy' to the generic 'phy'. Signed-off-by:
-
Dmitry Baryshkov authored
Change DSI PHY node names from custom 'dsi-phy' to the generic 'phy'. Signed-off-by:
-
Krzysztof Kozlowski authored
The TCSR mutex bindings allow device to be described only with address space (so it uses MMIO, not syscon regmap). This seems reasonable, as TCSR mutex is actually a dedicated IO address space, and it also fixes DT schema checks: qcom-msm8974-sony-xperia-rhine-amami.dtb: tcsr-mutex: 'reg' is a required property qcom-msm8974-sony-xperia-rhine-amami.dtb: tcsr-mutex: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by:
-
Krzysztof Kozlowski authored
TCSR syscon node should come with dedicated compatible. Signed-off-by:
-
Krzysztof Kozlowski authored
GPIO controller nodes are named by convention just "gpio", not "gpios". Signed-off-by:
-
Bryan O'Donoghue authored
phy-names has been marked deprecated. Remove it from the msm8974 DSI controller block. Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by:
-
Bryan O'Donoghue authored
phy-names has been marked deprecated. Remove it from the apq8064 DSI controller block. Signed-off-by:
-
Dmitry Baryshkov authored
Signed-off-by:
-
Dmitry Baryshkov authored
On MSM8660 the PMICs are connected using SSBI devices, which do not have any addressing scheme. Drop the unused unit ids from PMIC device nodes. Signed-off-by:
-
Dmitry Baryshkov authored
Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by:
-
Dmitry Baryshkov authored
Declare PM8058 LED devices in the main msm8660 DT file to allow them to be used by other devices. Signed-off-by:
-
Dmitry Baryshkov authored
The separate amba device node doesn't add anything significant to the DT. The OF parsing code already creates amba_device or platform_device depending on the compatibility lists. Drop the amba node and reorder sdcc nodes according to node addresses. Signed-off-by:
-
Dmitry Baryshkov authored
Drop the unused unit id from the gpio-regulator node, there is no addessing scheme in the /regulators node. Signed-off-by:
-
Dmitry Baryshkov authored
Signed-off-by:
-
Dmitry Baryshkov authored
On MSM8960 the PMICs are connected using SSBI devices, which do not have any addressing scheme. Drop the unused unit ids from PMIC device nodes. Signed-off-by:
-
Dmitry Baryshkov authored
Fix the address of the riva-pil node. The first region address is 0x3200800, so the node should also be called riva-pil@3200800. Signed-off-by:
-
Dmitry Baryshkov authored
Signed-off-by:
-
Dmitry Baryshkov authored
On APQ8064 the PMICs are connected using SSBI devices, which do not have any addressing scheme. Drop the unused unit ids from PMIC device nodes. Signed-off-by:
-
Dmitry Baryshkov authored
The separate amba device node doesn't add anything significant to the DT. The OF parsing code already creates amba_device or platform_device depending on the compatibility lists. Drop the amba node and reorder sdcc and sdcc bam nodes according to node addresses. Signed-off-by:
-
Dmitry Baryshkov authored
Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by:
-
Dmitry Baryshkov authored
There are no need to add additional simple-bus nodes just to populate a single pwrseq device. Pull it up one level into /. While we are at it also fix node name replacing underscore with dash. Signed-off-by:
-
Dmitry Baryshkov authored
The 3.3V regulator is not part of the SoC, so pull it from the SoC node. Signed-off-by:
-
Dmitry Baryshkov authored
Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by:
-
Dmitry Baryshkov authored
Rename ext 3p3v regulator node, fixing the 'node has a unit name, but no reg or ranges property' warning. Signed-off-by:
-
Dmitry Baryshkov authored
Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by:
-
Dmitry Baryshkov authored
There are no need to add additional simple-bus nodes just to populate a single pwrseq device. Pull it up one level into /. While we are at it also fix node name replacing underscore with dash. Signed-off-by:
-
Dmitry Baryshkov authored
There are no address-cells for the gpio-leds child nodes, so rename led@1 node to led-user1. Signed-off-by:
-
Dmitry Baryshkov authored
The ext 3.3V regulator is not part of the SoC, so pull it from the SoC node. Signed-off-by:
-
Dmitry Baryshkov authored
Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by:
-
Dmitry Baryshkov authored
Disable HDMI nodes. Individual board can enable them if required. The only APQ8064 board that has working HDMI output is IFC6410, which enables these devices explicitly. Signed-off-by:
-
