- 25 Aug, 2017 9 commits
-
-
Takashi Iwai authored
commit a8e800fe upstream. A Senheisser headset requires the typical sample-rate quirk for avoiding spurious errors from inquiring the current sample rate like: usb 1-1: 2:1: cannot get freq at ep 0x4 usb 1-1: 3:1: cannot get freq at ep 0x83 The USB ID 1395:740a has to be added to the entries in snd_usb_get_sample_rate_quirk(). Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1052580Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Mentz authored
commit 7e1d90f6 upstream. commit 4842e98f ("ALSA: seq: Fix race at creating a queue") attempted to fix a race reported by syzkaller. That fix has been described as follows: " When a sequencer queue is created in snd_seq_queue_alloc(),it adds the new queue element to the public list before referencing it. Thus the queue might be deleted before the call of snd_seq_queue_use(), and it results in the use-after-free error, as spotted by syzkaller. The fix is to reference the queue object at the right time. " Even with that fix in place, syzkaller reported a use-after-free error. It specifically pointed to the last instruction "return q->queue" in snd_seq_queue_alloc(). The pointer q is being used after kfree() has been called on it. It turned out that there is still a small window where a race can happen. The window opens at snd_seq_ioctl_create_queue()->snd_seq_queue_alloc()->queue_list_add() and closes at snd_seq_ioctl_create_queue()->queueptr()->snd_use_lock_use(). Between these two calls, a different thread could delete the queue and possibly re-create a different queue in the same location in queue_list. This change prevents this situation by calling snd_use_lock_use() from snd_seq_queue_alloc() prior to calling queue_list_add(). It is then the caller's responsibility to call snd_use_lock_free(&q->use_lock). Fixes: 4842e98f ("ALSA: seq: Fix race at creating a queue") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Daniel Mentz <danielmentz@google.com> Signed-off-by:
-
KT Liao authored
commit 76988690 upstream. Add 2 new IDs (ELAN0609 and ELAN060B) to the list of ACPI IDs that should be handled by the driver. Signed-off-by:
KT Liao <kt.liao@emc.com.tw> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 1874064e upstream. Similar to commit 722c5ac7 ("Input: elan_i2c - add ELAN0605 to the ACPI table"), ELAN0608 should be handled by elan_i2c. This touchpad can be found in Lenovo ideapad 320-14IKB. BugLink: https://bugs.launchpad.net/bugs/1708852Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
megha.dey@linux.intel.com authored
commit 8861249c upstream. It was reported that the sha1 AVX2 function(sha1_transform_avx2) is reading ahead beyond its intended data, and causing a crash if the next block is beyond page boundary: http://marc.info/?l=linux-crypto-vger&m=149373371023377 This patch makes sure that there is no overflow for any buffer length. It passes the tests written by Jan Stancek that revealed this problem: https://github.com/jstancek/sha1-avx2-crash I have re-enabled sha1-avx2 by reverting commit b82ce244 Fixes: b82ce244 ("crypto: sha1-ssse3 - Disable avx2") Originally-by:
Ilya Albrekht <ilya.albrekht@intel.com> Tested-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Megha Dey <megha.dey@linux.intel.com> Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
commit 28389575 upstream. In commit 0f987e25, the source processing has been moved in front of the destination processing, but the error handling path has not been modified accordingly. Free resources in the correct order to avoid some leaks. Fixes: 0f987e25 ("crypto: ixp4xx - Fix false lastlen uninitialised warning") Reported-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Thomas Bogendoerfer authored
commit 40981160 upstream. For 64bit kernels the lmmio_space_offset of the host bridge window isn't set correctly on systems with dino/cujo PCI host bridges. This leads to not assigned memory bars and failing drivers, which need to use these bars. Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Jan Kara authored
commit d76036ab upstream. audit_remove_watch_rule() drops watch's reference to parent but then continues to work with it. That is not safe as parent can get freed once we drop our reference. The following is a trivial reproducer: mount -o loop image /mnt touch /mnt/file auditctl -w /mnt/file -p wax umount /mnt auditctl -D <crash in fsnotify_destroy_mark()> Grab our own reference in audit_remove_watch_rule() earlier to make sure mark does not get freed under us. Reported-by:
Tony Jones <tonyj@suse.de> Signed-off-by:
Jan Kara <jack@suse.cz> Tested-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Liping Zhang authored
commit 9c3f3794 upstream. If one cpu is doing nf_ct_extend_unregister while another cpu is doing __nf_ct_ext_add_length, then we may hit BUG_ON(t == NULL). Moreover, there's no synchronize_rcu invocation after set nf_ct_ext_types[id] to NULL, so it's possible that we may access invalid pointer. But actually, most of the ct extends are built-in, so the problem listed above will not happen. However, there are two exceptions: NF_CT_EXT_NAT and NF_CT_EXT_SYNPROXY. For _EXT_NAT, the panic will not happen, since adding the nat extend and unregistering the nat extend are located in the same file(nf_nat_core.c), this means that after the nat module is removed, we cannot add the nat extend too. For _EXT_SYNPROXY, synproxy extend may be added by init_conntrack, while synproxy extend unregister will be done by synproxy_core_exit. So after nf_synproxy_core.ko is removed, we may still try to add the synproxy extend, then kernel panic may happen. I know it's very hard to reproduce this issue, but I can play a tricky game to make it happen very easily :) Step 1. Enable SYNPROXY for tcp dport 1234 at FORWARD hook: # iptables -I FORWARD -p tcp --dport 1234 -j SYNPROXY Step 2. Queue the syn packet to the userspace at raw table OUTPUT hook. Also note, in the userspace we only add a 20s' delay, then reinject the syn packet to the kernel: # iptables -t raw -I OUTPUT -p tcp --syn -j NFQUEUE --queue-num 1 Step 3. Using "nc 2.2.2.2 1234" to connect the server. Step 4. Now remove the nf_synproxy_core.ko quickly: # iptables -F FORWARD # rmmod ipt_SYNPROXY # rmmod nf_synproxy_core Step 5. After 20s' delay, the syn packet is reinjected to the kernel. Now you will see the panic like this: kernel BUG at net/netfilter/nf_conntrack_extend.c:91! Call Trace: ? __nf_ct_ext_add_length+0x53/0x3c0 [nf_conntrack] init_conntrack+0x12b/0x600 [nf_conntrack] nf_conntrack_in+0x4cc/0x580 [nf_conntrack] ipv4_conntrack_local+0x48/0x50 [nf_conntrack_ipv4] nf_reinject+0x104/0x270 nfqnl_recv_verdict+0x3e1/0x5f9 [nfnetlink_queue] ? nfqnl_recv_verdict+0x5/0x5f9 [nfnetlink_queue] ? nla_parse+0xa0/0x100 nfnetlink_rcv_msg+0x175/0x6a9 [nfnetlink] [...] One possible solution is to make NF_CT_EXT_SYNPROXY extend built-in, i.e. introduce nf_conntrack_synproxy.c and only do ct extend register and unregister in it, similar to nf_conntrack_timeout.c. But having such a obscure restriction of nf_ct_extend_unregister is not a good idea, so we should invoke synchronize_rcu after set nf_ct_ext_types to NULL, and check the NULL pointer when do __nf_ct_ext_add_length. Then it will be easier if we add new ct extend in the future. Last, we use kfree_rcu to free nf_ct_ext, so rcu_barrier() is unnecessary anymore, remove it too. Signed-off-by:
Liping Zhang <zlpnobody@gmail.com> Acked-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Cc: Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
-
- 16 Aug, 2017 31 commits
-
-
Greg Kroah-Hartman authored
-
Maciej W. Rozycki authored
commit 68fe5568 upstream. Fix a commit 3021773c ("MIPS: DEC: Avoid la pseudo-instruction in delay slots") regression and remove assembly errors: arch/mips/dec/int-handler.S: Assembler messages: arch/mips/dec/int-handler.S:162: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:163: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:229: Error: Macro used $at after ".set noat" arch/mips/dec/int-handler.S:230: Error: Macro used $at after ".set noat" triggering with with the CPU_DADDI_WORKAROUNDS option set and the DADDIU instruction. This is because with that option in place the instruction becomes a macro, which expands to an LI/DADDU (or actually ADDIU/DADDU) sequence that uses $at as a temporary register. With CPU_DADDI_WORKAROUNDS we only support `-msym32' compilation though, and this is already enforced in arch/mips/Makefile, so choose the 32-bit expansion variant for the supported configurations and then replace the 64-bit variant with #error just in case. Fixes: 3021773c ("MIPS: DEC: Avoid la pseudo-instruction in delay slots") Signed-off-by:
Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16893/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Neil Armstrong authored
commit 34e61801 upstream. GPIODV_18 entry was missing in the original driver push. Fixes: 468c234f ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC") Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
Jerome Brunet <jbrunet@baylibre.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Thomas Gleixner authored
commit 3fa53ec2 upstream. The irq chip callbacks irq_request/release_resources() have absolutely no business with masking and unmasking the irq. The core code unmasks the interrupt after complete setup and masks it before invoking irq_release_resources(). The unmask is actually harmful as it happens before the interrupt is completely initialized in __setup_irq(). Remove it. Fixes: f6a8249f ("pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs") Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Kukjin Kim <kgene@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-gpio@vger.kernel.org Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by:
-
Masahiro Yamada authored
commit 1bd303dc upstream. The pingroups dump of debugfs hits WARN_ON() in pinctrl_groups_show(). Filling non-existing ports with '-1' turned out a bad idea. Fixes: 336306ee ("pinctrl: uniphier: add UniPhier PH1-LD20 pinctrl driver") Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Masahiro Yamada authored
commit 9592bc25 upstream. The pingroups dump of debugfs hits WARN_ON() in pinctrl_groups_show(). Filling non-existing ports with '-1' turned out a bad idea. Fixes: 70f2f9c4 ("pinctrl: uniphier: add UniPhier PH1-LD11 pinctrl driver") Signed-off-by:
-
Andy Shevchenko authored
commit 5d996132 upstream. UART pin lists consist GPIO numbers which is simply wrong. Replace it by pin numbers. Fixes: 4e80c8f5 ("pinctrl: intel: Add Intel Merrifield pin controller support") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Icenowy Zheng authored
commit d81ece74 upstream. The PH16 pin has a function with mux id 0x5, which is the DET pin of the "sim" (smart card reader) IP block. This function is missing in old versions of A10/A20 SoCs' datasheets and user manuals, so it's also missing in the old drivers. The newest A10 Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and it's discovered during implementing R40 pinctrl driver. Add it to the driver. As we now merged A20 pinctrl driver to the A10 one, we need to only fix the A10 driver now. Fixes: f2821b1c ("pinctrl: sunxi: Move Allwinner A10 pinctrl driver to a driver of its own") Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Reviewed-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Christoph Hellwig authored
commit 8a9d6e96 upstream. The blocklayout code does not compile cleanly for a 32-bit sector_t, and also has no reliable checks for devices sizes, which makes it unsafe to use with a kernel that doesn't support large block devices. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reported-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Stefan-Gabriel Mirea authored
commit d466d3c1 upstream. In order to select the alternate voltage reference pair (VALTH/VALTL), the right value for the REFSEL field in the ADCx_CFG register is "01", leading to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1]. [1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf Fixes: a7754276 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver") Signed-off-by:
Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Sandeep Singh authored
commit e788787e upstream. Certain HP keyboards would keep inputting a character automatically which is the wake-up key after S3 resume On some AMD platforms USB host fails to respond (by holding resume-K) to USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures that resume is signaled for at least 20 ms (TDRSMDN), which is defined in USB 2.0 spec. The result is that the keyboard is out of function. In SNPS USB design, the host responds to the resume request only after system gets back to S0 and the host gets to functional after the internal HW restore operation that is more than 1 second after the initial resume request from the USB device. As a workaround for specific keyboard ID(HP Keyboards), applying port reset after resume when the keyboard is plugged in. Signed-off-by:
Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Reviewed-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 7496cfe5 upstream. Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to connect to Realtek r8153. The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk can make it work. Since another r8153 dongle at my hand does not have the issue, so add the quirk to the Genesys Logic hub instead. Signed-off-by:
-
Bin Liu authored
commit 2eac1362 upstream. While unlink an urb, if the urb has been programmed in the controller, the controller driver might do some hw related actions to tear down the urb. Currently usb_hcd_flush_endpoint() passes each urb from the head of the endpoint's urb_list to the controller driver, which could make the controller driver think each urb has been programmed and take the unnecessary actions for each urb. This patch changes the behavior in usb_hcd_flush_endpoint() to pass the urbs from the tail of the list, to avoid any unnecessary actions in an controller driver. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Alan Stern authored
commit 94c43b98 upstream. Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4c ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by:
Zdenek Kabelac <zkabelac@redhat.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Yoshihiro Shimoda authored
commit 2acecd58 upstream. The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit. If the bit sets to 1, the VBUS drive is controlled by phy related registers (called "UCOM Registers" on the manual). Since R-Car Gen3 environment will control VBUS by phy-rcar-gen3-usb2 driver, the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes the register's value. Otherwise, even if the ID pin indicates to peripheral, the R-Car will output USBn_PWEN to 1 when a host driver is running. Fixes: de18757e ("usb: renesas_usbhs: add R-Car Gen3 power control" Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
commit aca5b9eb upstream. According to the gadget.h, a "complete" function will always be called with interrupts disabled. However, sometimes usb3_request_done() function is called with interrupts enabled. So, this function should be held by spin_lock_irqsave() to disable interruption. Also, this driver has to call spin_unlock() to avoid spinlock recursion by this driver before calling usb_gadget_giveback_request(). Reported-by:
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Tested-by:
-
Alan Swanson authored
commit 89f23d51 upstream. Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by:
Alan Swanson <reiver@improbability.net> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Ian Abbott authored
commit cef98864 upstream. Comedi's read and write file operation handlers (`comedi_read()` and `comedi_write()`) currently call `copy_to_user()` or `copy_from_user()` whilst in the `TASK_INTERRUPTIBLE` state, which falls foul of the `might_fault()` checks when enabled. Fix it by setting the current task state back to `TASK_RUNNING` a bit earlier before calling these functions. Reported-by:
Piotr Gregor <piotrgregor@rsyncme.org> Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Akinobu Mita authored
commit a3507e48 upstream. The TSL2563 driver provides three iio channels, two of which are raw ADC channels (channel 0 and channel 1) in the device and the remaining one is calculated by the two. The ADC channel 0 only supports programmable interrupt with threshold settings and this driver supports the event but the generated event code does not contain the corresponding iio channel type. This is going to change userspace ABI. Hopefully fixing this to be what it should always have been won't break any userspace code. Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit e59e1898 upstream. After probe we would put the device in normal mode, after a runtime suspend-resume we would put it back in normal mode. But for a regular suspend-resume we would only put it back in normal mode if triggers or events have been requested. This is not consistent and breaks reading raw values after a suspend-resume. This commit changes the regular resume path to also unconditionally put the device back in normal mode, fixing reading of raw values not working after a regular suspend-resume cycle. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Arnd Bergmann authored
commit 105967ad upstream. gcc-7 points out an older regression: drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw': drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] The original code had 'unsigned short' here, but incorrectly got converted to 'bool'. This reverts the regression and uses a normal type instead. Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.") Signed-off-by:
-
Rafael J. Wysocki authored
commit cd5a6a4f upstream. Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Bin Liu authored
commit 45d73860 upstream. commit 68fe05e2 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Signed-off-by:
-
Greg Kroah-Hartman authored
commit 3b6bcd3d upstream. This adds a new ATEN device id for a new pl2303-based device. Reported-by:
Peter Kuo <PeterKuo@aten.com.tw> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Stefan Triller authored
commit 9585e340 upstream. The German Telekom offers a ZigBee USB Stick under the brand name Qivicon for their SmartHome Home Base in its 1. Generation. The productId is not known by the according kernel module, this patch adds support for it. Signed-off-by:
Stefan Triller <github@stefantriller.de> Reviewed-by:
Frans Klaver <fransklaver@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hector Martin authored
commit fd1b8668 upstream. Add device id for D-Link DWM-222. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Maarten Lankhorst authored
commit 5279fc77 upstream. bdw_load_gamma_lut is writing beyond the array to the maximum value. The intend of the function is to clamp values > 1 to 1, so write the intended color to the max register. This fixes the following KASAN warning: [ 197.020857] [IGT] kms_pipe_color: executing [ 197.063434] [IGT] kms_pipe_color: starting subtest ctm-0-25-pipe0 [ 197.078989] ================================================================== [ 197.079127] BUG: KASAN: slab-out-of-bounds in bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079188] Read of size 2 at addr ffff8800d38db150 by task kms_pipe_color/1839 [ 197.079208] CPU: 2 PID: 1839 Comm: kms_pipe_color Tainted: G U 4.13.0-rc1-patser+ #5211 [ 197.079215] Hardware name: NUC5i7RYB, BIOS RYBDWi35.86A.0246.2015.0309.1355 03/09/2015 [ 197.079220] Call Trace: [ 197.079230] dump_stack+0x68/0x9e [ 197.079239] print_address_description+0x6f/0x250 [ 197.079251] kasan_report+0x216/0x370 [ 197.079374] ? bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079451] ? gen8_write16+0x4e0/0x4e0 [i915] [ 197.079460] __asan_report_load2_noabort+0x14/0x20 [ 197.079535] bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079612] broadwell_load_luts+0x1df/0x550 [i915] [ 197.079690] intel_color_load_luts+0x7b/0x80 [i915] [ 197.079764] intel_begin_crtc_commit+0x138/0x760 [i915] [ 197.079783] drm_atomic_helper_commit_planes_on_crtc+0x1a3/0x820 [drm_kms_helper] [ 197.079859] ? intel_pre_plane_update+0x571/0x580 [i915] [ 197.079937] intel_update_crtc+0x238/0x330 [i915] [ 197.080016] intel_update_crtcs+0x10f/0x210 [i915] [ 197.080092] intel_atomic_commit_tail+0x1552/0x3340 [i915] [ 197.080101] ? _raw_spin_unlock+0x3c/0x40 [ 197.080110] ? __queue_work+0xb40/0xbf0 [ 197.080188] ? skl_update_crtcs+0xc00/0xc00 [i915] [ 197.080195] ? trace_hardirqs_on+0xd/0x10 [ 197.080269] ? intel_atomic_commit_ready+0x128/0x13c [i915] [ 197.080329] ? __i915_sw_fence_complete+0x5b8/0x6d0 [i915] [ 197.080336] ? debug_object_activate+0x39e/0x580 [ 197.080397] ? i915_sw_fence_await+0x30/0x30 [i915] [ 197.080409] ? __might_sleep+0x15b/0x180 [ 197.080483] intel_atomic_commit+0x944/0xa70 [i915] [ 197.080490] ? refcount_dec_and_test+0x11/0x20 [ 197.080567] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080597] ? drm_atomic_crtc_set_property+0x303/0x580 [drm] [ 197.080674] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080704] drm_atomic_commit+0xd7/0xe0 [drm] [ 197.080722] drm_atomic_helper_crtc_set_property+0xec/0x130 [drm_kms_helper] [ 197.080749] drm_mode_crtc_set_obj_prop+0x7d/0xb0 [drm] [ 197.080775] drm_mode_obj_set_property_ioctl+0x50b/0x5d0 [drm] [ 197.080783] ? __might_fault+0x104/0x180 [ 197.080809] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080838] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080861] drm_ioctl_kernel+0x154/0x1a0 [drm] [ 197.080885] drm_ioctl+0x624/0x8f0 [drm] [ 197.080910] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080934] ? drm_getunique+0x210/0x210 [drm] [ 197.080943] ? __handle_mm_fault+0x1bd0/0x1ce0 [ 197.080949] ? lock_downgrade+0x610/0x610 [ 197.080957] ? __lru_cache_add+0x15a/0x180 [ 197.080967] do_vfs_ioctl+0xd92/0xe40 [ 197.080975] ? ioctl_preallocate+0x1b0/0x1b0 [ 197.080982] ? selinux_capable+0x20/0x20 [ 197.080991] ? __do_page_fault+0x7b7/0x9a0 [ 197.080997] ? lock_downgrade+0x5bb/0x610 [ 197.081007] ? security_file_ioctl+0x57/0x90 [ 197.081016] SyS_ioctl+0x4e/0x80 [ 197.081024] entry_SYSCALL_64_fastpath+0x18/0xad [ 197.081030] RIP: 0033:0x7f61f287a987 [ 197.081035] RSP: 002b:00007fff7d44d188 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 197.081043] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f61f287a987 [ 197.081048] RDX: 00007fff7d44d1c0 RSI: 00000000c01864ba RDI: 0000000000000003 [ 197.081053] RBP: 00007f61f2b3eb00 R08: 0000000000000059 R09: 0000000000000000 [ 197.081058] R10: 0000002ea5c4a290 R11: 0000000000000246 R12: 00007f61f2b3eb58 [ 197.081063] R13: 0000000000001010 R14: 00007f61f2b3eb58 R15: 0000000000002702 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101659Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reported-by:
Martin Peres <martin.peres@linux.intel.com> Cc: Martin Peres <martin.peres@linux.intel.com> Fixes: 82cf435b ("drm/i915: Implement color management on bdw/skl/bxt/kbl") Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Kiran S Kumar <kiran.s.kumar@intel.com> Cc: Kausal Malladi <kausalmalladi@gmail.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20170724091431.24251-1-maarten.lankhorst@linux.intel.comReviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> (cherry picked from commit 09a92bc8) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Wladimir J. van der Laan authored
commit d6f756e0 upstream. A relocation pointing to the last four bytes of a buffer can legitimately happen in the case of small vertex buffers. Signed-off-by:
Wladimir J. van der Laan <laanwj@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Weston Andros Adamson authored
commit 1feb2616 upstream. The client was freeing the nfs4_ff_layout_ds, but not the contained nfs4_ff_ds_version array. Signed-off-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
-
Haibo Chen authored
commit 92ddd959 upstream. Change the default err value to -EINVAL, make sure the card only has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage setting when select hs400es mode. Fixes: commit 1720d354 ("mmc: core: switch to 1V8 or 1V2 for hs400es mode") Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Miquel Raynal authored
commit f7f8c175 upstream. When using soft ecc, if no ooblayout is given, the core automatically uses one of the nand_ooblayout_{sp,lp}*() functions to determine the layout inside the out of band data. Until kernel version 4.6, struct nand_ecclayout was used for that purpose. During the migration from 4.6 to 4.7, an error shown up in the small page layout, in the case oob section is only 8 bytes long. The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4) as free bytes, one byte (5) for bad block marker and finally two bytes (6, 7) as free bytes, as shown there: [linux-4.6] drivers/mtd/nand/nand_base.c:52 static struct nand_ecclayout nand_oob_8 = { .eccbytes = 3, .eccpos = {0, 1, 2}, .oobfree = { {.offset = 3, .length = 2}, {.offset = 6, .length = 2} } }; This fixes the current implementation which is incoherent. It references bit 3 at the same time as an ecc byte and a free byte. Furthermore, it is clear with the previous implementation that there is only one ecc section with 8 bytes oob sections. We shall return -ERANGE in the nand_ooblayout_ecc_sp() function when asked for the second section. Signed-off-by:
Miquel Raynal <miquel.raynal@free-electrons.com> Fixes: 41b207a7 ("mtd: nand: implement the default mtd_ooblayout_ops") Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
