- 19 Feb, 2015 40 commits
-
-
Ahmed S. Darwish authored
commit 5e7e6e0c upstream. Recent Leaf firmware versions (>= 3.1.557) do not allow to send commands for non-existing channels. If a command is sent for a non-existing channel, the firmware crashes. Reported-by:
Christopher Storah <Christopher.Storah@invetech.com.au> Signed-off-by:
Olivier Sobrie <olivier@sobrie.be> Signed-off-by:
Ahmed S. Darwish <ahmed.darwish@valeo.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Ahmed S. Darwish authored
commit 889b77f7 upstream. Flooding the Kvaser CAN to USB dongle with multiple reads and writes in very high frequency (*), closing the CAN channel while all the transmissions are on (#), opening the device again (@), then sending a small number of packets would make the driver enter an almost infinite loop of: [....] [15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context [15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context [....] _dragging the whole system down_ in the process due to the excessive logging output. Initially, this has caused random panics in the kernel due to a buggy error recovery path. That got fixed in an earlier commit.(%) This patch aims at solving the root cause. --> 16 tx URBs and contexts are allocated per CAN channel per USB device. Such URBs are protected by: a) A simple atomic counter, up to a value of MAX_TX_URBS (16) b) A flag in each URB context, stating if it's free c) The fact that ndo_start_xmit calls are themselves protected by the networking layers higher above After grabbing one of the tx URBs, if the driver noticed that all of them are now taken, it stops the netif transmission queue. Such queue is worken up again only if an acknowedgment was received from the firmware on one of our earlier-sent frames. Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP to the firmware, effectively closing all further communication. In the high traffic case, the atomic counter remains at MAX_TX_URBS, and all the URB contexts remain marked as active. While opening the channel again (@), it cannot send any further frames since no more free tx URB contexts are available. Reset all tx URB contexts upon CAN channel close. (*) 50 parallel instances of `cangen0 -g 0 -ix` (#) `ifconfig can0 down` (@) `ifconfig can0 up` (%) "can: kvaser_usb: Don't free packets when tight on URBs" Signed-off-by:
-
Ahmed S. Darwish authored
commit b442723f upstream. Flooding the Kvaser CAN to USB dongle with multiple reads and writes in high frequency caused seemingly-random panics in the kernel. On further inspection, it seems the driver erroneously freed the to-be-transmitted packet upon getting tight on URBs and returning NETDEV_TX_BUSY, leading to invalid memory writes and double frees at a later point in time. Note: Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY is a driver bug in and out of itself: it means that our start/stop queue flow control is broken. This patch only fixes the (buggy) error handling code; the root cause shall be fixed in a later commit. Acked-by:
-
Oliver Hartkopp authored
commit 9b1087aa upstream. When changing flags in the CAN drivers ctrlmode the provided new content has to be checked whether the bits are allowed to be changed. The bits that are to be changed are given as a bitfield in cm->mask. Therefore checking against cm->flags is wrong as the content can hold any kind of values. The iproute2 tool sets the bits in cm->mask and cm->flags depending on the detected command line options. To be robust against bogus user space applications additionally sanitize the provided flags with the provided mask. Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Johan Hovold authored
commit 6798acaa upstream. Move direct and indirect calls to gpiochip_remove_pin_ranges outside of spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range. Note that the pin ranges are already added outside of the lock. Fixes: 9ef0d6f7 ("gpiolib: call pin removal in chip removal function") Fixes: f23f1516 ("gpiolib: provide provision to register pin ranges") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Johan Hovold authored
commit 5539b3c9 upstream. Memory allocated and references taken by of_gpiochip_add and acpi_gpiochip_add were never released on errors in gpiochip_add (e.g. failure to find free gpio range). Fixes: 391c970c ("of/gpio: add default of_xlate function if device has a node pointer") Fixes: 664e3e5a ("gpio / ACPI: register to ACPI events automatically") Signed-off-by:
-
Mika Westerberg authored
commit 664e3e5a upstream. Instead of asking each driver to register to ACPI events we can just call acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle. The function checks chip->to_irq and if it is set to NULL (a GPIO driver that doesn't do interrupts) the function does nothing. We also add the a new header drivers/gpio/gpiolib.h that is used for functions internal to gpiolib and add ACPI GPIO chip registering functions to that header. Once that is done we can remove call to acpi_gpiochip_register_interrupts() from its only user, pinctrl-baytrail.c Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Jim Lin authored
commit db93facf upstream. This patch is to fix two deadlock cases. Deadlock 1: CPU #1 pinctrl_register-> pinctrl_get -> create_pinctrl (Holding lock pinctrl_maps_mutex) -> get_pinctrl_dev_from_devname (Trying to acquire lock pinctrldev_list_mutex) CPU #0 pinctrl_unregister (Holding lock pinctrldev_list_mutex) -> pinctrl_put ->> pinctrl_free -> pinctrl_dt_free_maps -> pinctrl_unregister_map (Trying to acquire lock pinctrl_maps_mutex) Simply to say CPU#1 is holding lock A and trying to acquire lock B, CPU#0 is holding lock B and trying to acquire lock A. Deadlock 2: CPU #3 pinctrl_register-> pinctrl_get -> create_pinctrl (Holding lock pinctrl_maps_mutex) -> get_pinctrl_dev_from_devname (Trying to acquire lock pinctrldev_list_mutex) CPU #2 pinctrl_unregister (Holding lock pctldev->mutex) -> pinctrl_put ->> pinctrl_free -> pinctrl_dt_free_maps -> pinctrl_unregister_map (Trying to acquire lock pinctrl_maps_mutex) CPU #0 tegra_gpio_request (Holding lock pinctrldev_list_mutex) -> pinctrl_get_device_gpio_range (Trying to acquire lock pctldev->mutex) Simply to say CPU#3 is holding lock A and trying to acquire lock D, CPU#2 is holding lock B and trying to acquire lock A, CPU#0 is holding lock D and trying to acquire lock B. Signed-off-by:
Jim Lin <jilin@nvidia.com> Signed-off-by:
-
Alex Deucher authored
commit 5615f890 upstream. This adds a quirks list to fix stability problems with certain SI boards. bug: https://bugs.freedesktop.org/show_bug.cgi?id=76490Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Chris Wilson authored
commit 226e5ae9 upstream. If CONFIG_DEBUG_MUTEXES is set, the mutex->owner field is only cleared if the mutex debugging is enabled which introduces a race in our mutex_is_locked_by() - i.e. we may inspect the old owner value before it is acquired by the new task. This is the root cause of this error: diff --git a/kernel/locking/mutex-debug.c b/kernel/locking/mutex-debug.c index 5cf6731..3ef3736 100644 --- a/kernel/locking/mutex-debug.c +++ b/kernel/locking/mutex-debug.c @@ -80,13 +80,13 @@ void debug_mutex_unlock(struct mutex *lock) DEBUG_LOCKS_WARN_ON(lock->owner != current); DEBUG_LOCKS_WARN_ON(!lock->wait_list.prev && !lock->wait_list.next); - mutex_clear_owner(lock); } /* * __mutex_slowpath_needs_to_unlock() is explicitly 0 for debug * mutexes so that we can do it here after we've verified state. */ + mutex_clear_owner(lock); atomic_set(&lock->count, 1); } Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87955Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Dmitry Torokhov authored
commit 9333caea upstream. When KBC is in active multiplexing mode the touchpad on this laptop does not work. Reported-by:
Bilal Koc <koc.bilo@googlemail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Sam hung authored
commit 810aa091 upstream. This change allows the driver to recognize newer Elantech touchpads. Signed-off-by:
Yi ju Hong <sam.hung@emc.com.tw> Signed-off-by:
-
Alex Deucher authored
commit 4369a69e upstream. Disable dpm on certain problematic boards rather than disabling dpm for the entire chip family since most boards work fine. https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386534 https://bugzilla.kernel.org/show_bug.cgi?id=83731Signed-off-by:
-
Alex Deucher authored
commit 3a01fd36 upstream. We need to wait for the GPUVM flush to complete. There was some confusion as to how this mechanism was supposed to work. The operation is not atomic. For GPU initiated invalidations you need to read back a VM register to introduce enough latency for the update to complete. v2: drop gart changes v3: just read back rather than polling Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Alex Deucher authored
commit d474ea7e upstream. We need to wait for the GPUVM flush to complete. There was some confusion as to how this mechanism was supposed to work. The operation is not atomic. For GPU initiated invalidations you need to read back a VM register to introduce enough latency for the update to complete. v2: drop gart changes v3: just read back rather than polling Reviewed-by:
-
Alex Deucher authored
commit cbfc35b9 upstream. We need to wait for the GPUVM flush to complete. There was some confusion as to how this mechanism was supposed to work. The operation is not atomic. For GPU initiated invalidations you need to read back a VM register to introduce enough latency for the update to complete. v2: drop gart changes v3: just read back rather than polling Reviewed-by:
-
Srihari Vijayaraghavan authored
commit 148e9a71 upstream. On some laptops, keyboard needs to be reset in order to successfully detect touchpad (e.g., some Gigabyte laptop models with Elantech touchpads). Without resettin keyboard touchpad pretends to be completely dead. Based on the original patch by Mateusz Jończyk this version has been expanded to include DMI based detection & application of the fix automatically on the affected models of laptops. This has been confirmed to fix problem by three users already on three different models of laptops. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81331Signed-off-by:
Srihari Vijayaraghavan <linux.bug.reporting@gmail.com> Acked-by:
Mateusz Jończyk <mat.jonczyk@o2.pl> Tested-by:
Guillaum Bouchard <guillaum.bouchard@gmail.com> Signed-off-by:
-
Sasha Levin authored
commit 6ada1fc0 upstream. An unvalidated user input is multiplied by a constant, which can result in an undefined behaviour for large values. While this is validated later, we should avoid triggering undefined behaviour. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> [jstultz: include trivial milisecond->microsecond correction noticed by Andy] Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
Tobias Jakobi authored
commit 8c38d28b upstream. EXYNOS4_MCT_L_MASK is defined as 0xffffff00, so applying this bitmask produces a number outside the range 0x00 to 0xff, which always results in execution of the default switch statement. Obviously this is wrong and git history shows that the bitmask inversion was incorrectly set during a refactoring of the MCT code. Fix this by putting the inversion at the correct position again. Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Reported-by:
GP Orcullo <kinsamanka@gmail.com> Reviewed-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 237d28db upstream. If the function graph tracer traces a jprobe callback, the system will crash. This can easily be demonstrated by compiling the jprobe sample module that is in the kernel tree, loading it and running the function graph tracer. # modprobe jprobe_example.ko # echo function_graph > /sys/kernel/debug/tracing/current_tracer # ls The first two commands end up in a nice crash after the first fork. (do_fork has a jprobe attached to it, so "ls" just triggers that fork) The problem is caused by the jprobe_return() that all jprobe callbacks must end with. The way jprobes works is that the function a jprobe is attached to has a breakpoint placed at the start of it (or it uses ftrace if fentry is supported). The breakpoint handler (or ftrace callback) will copy the stack frame and change the ip address to return to the jprobe handler instead of the function. The jprobe handler must end with jprobe_return() which swaps the stack and does an int3 (breakpoint). This breakpoint handler will then put back the saved stack frame, simulate the instruction at the beginning of the function it added a breakpoint to, and then continue on. For function tracing to work, it hijakes the return address from the stack frame, and replaces it with a hook function that will trace the end of the call. This hook function will restore the return address of the function call. If the function tracer traces the jprobe handler, the hook function for that handler will not be called, and its saved return address will be used for the next function. This will result in a kernel crash. To solve this, pause function tracing before the jprobe handler is called and unpause it before it returns back to the function it probed. Some other updates: Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the code look a bit cleaner and easier to understand (various tries to fix this bug required this change). Note, if fentry is being used, jprobes will change the ip address before the function graph tracer runs and it will not be able to trace the function that the jprobe is probing. Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.orgAcked-by:
Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Amit Virdi authored
commit 39e60635 upstream. DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This means, the max TRBs that can be submitted for an EP is fixed to 32. Since the request queue for an EP is a linked list, any number of requests can be queued to it by the gadget layer. However, the dwc3 driver must not submit TRBs more than the pool it has created for. This limit wasn't respected when SG was used resulting in submitting more than the max TRBs, eventually leading to non-transfer of the TRBs submitted over the max limit. Root cause: When SG is used, there are two loops iterating to prepare TRBs: - Outer loop over the request_list - Inner loop over the SG list The code was missing break to get out of the outer loop. Fixes: eeb720fb (usb: dwc3: gadget: add support for SG lists) Signed-off-by:
Amit Virdi <amit.virdi@st.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Amit Virdi authored
commit ec512fb8 upstream. When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3 request (dwc3_request). So while preparing TRBs, the 'last' flag should be set only when it is the last TRB being prepared from the last dwc3_request entry. The current implementation uses list_is_last to check if the dwc3_request is the last entry from the request_list. However, list_is_last returns false for the last entry too. This is because, while preparing the first TRB from a request, the function dwc3_prepare_one_trb modifies the request's next and prev pointers while moving the URB to req_queued. Hence, list_is_last always returns false no matter what. The correct way is not to access the modified pointers of dwc3_request but to use list_empty macro instead. Fixes: e5ba5ec8 (usb: dwc3: gadget: fix scatter gather implementation) Signed-off-by:
-
Krzysztof Kozlowski authored
commit 2836766a upstream. Sleep in atomic context happened on Trats2 board after inserting or removing SD card because mmc_gpio_get_cd() was called under spin lock. Fix this by moving card detection earlier, before acquiring spin lock. The mmc_gpio_get_cd() call does not have to be protected by spin lock because it does not access any sdhci internal data. The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After moving it out side of spin lock it could theoretically race with driver removal but still there is no actual protection against manual card eject. Dmesg after inserting SD card: [ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511 [ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1 [ 41.677580] INFO: lockdep is turned off. [ 41.681486] irq event stamp: 61972 [ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c [ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54 [ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8 [ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114 [ 41.716206] Preemption disabled at:[< (null)>] (null) [ 41.721500] [ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883 [ 41.732111] Workqueue: kmmcd mmc_rescan [ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14) [ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc) [ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30) [ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58) [ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4) [ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268) [ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0) [ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78) [ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124) [ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64) [ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4) [ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4) [ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0) [ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104) [ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c) [ 42.038276] mmc0: new high speed SDHC card at address 1234 Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 94144a46 ("mmc: sdhci: add get_cd() implementation") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Johan Hovold authored
commit 32a4bf2e upstream. Use tty kref to release the fake tty in usb_console_setup to avoid use after free if the underlying serial driver has acquired a reference. Note that using the tty destructor release_one_tty requires some more state to be initialised. Fixes: 4a90f09b ("tty: usb-serial krefs") Signed-off-by:
-
Johan Hovold authored
commit d269d443 upstream. The USB console currently allocates a temporary fake tty which is used to pass terminal settings to the underlying serial driver. The tty struct is not fully initialised, something which can lead to a lockdep warning (or worse) if a serial driver tries to acquire a line-discipline reference: usbserial: USB Serial support registered for pl2303 pl2303 1-2.1:1.0: pl2303 converter detected usb 1-2.1: pl2303 converter now attached to ttyUSB0 INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 0 PID: 68 Comm: udevd Tainted: G W 3.18.0-rc5 #10 [<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24) [<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28) [<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004) [<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c) [<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90) [<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58) [<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8) [<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303]) [<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140) [<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4) [<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108) [<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c) [<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114) [<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc) [<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0) [<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c) Exception stack(0xdf4e7f08 to 0xdf4e7f50) 7f00: debc0b80 df4e7f5c 00000000 00000000 debc0b80 be8da96c 7f20: 00000000 00000128 c000fc84 df4e6000 00000000 df4e7f94 00000004 df4e7f50 7f40: c038ebc0 c038d74c 600f0013 ffffffff [<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0) [<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c) [<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48) console [ttyUSB0] enabled Fixes: 36697529 ("tty: Replace ldisc locking with ldisc_sem") Signed-off-by:
-
Songjun Wu authored
commit 5fb694f9 upstream. When unloading the module 'g_hid.ko', the urb request will be dequeued and the completion routine will be excuted. If there is no urb packet, the urb request will not be added to the endpoint queue and the completion routine pointer in urb request is NULL. Accessing to this NULL function pointer will cause the Oops issue reported below. Add the code to check if the urb request is in the endpoint queue or not. If the urb request is not in the endpoint queue, a negative error code will be returned. Here is the Oops log: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = dedf0000 [00000000] *pgd=3ede5831, *pte=00000000, *ppte=00000000 Internal error: Oops: 80000007 [#1] ARM Modules linked in: g_hid(-) usb_f_hid libcomposite CPU: 0 PID: 923 Comm: rmmod Not tainted 3.18.0+ #2 Hardware name: Atmel SAMA5 (Device Tree) task: df6b1100 ti: dedf6000 task.ti: dedf6000 PC is at 0x0 LR is at usb_gadget_giveback_request+0xc/0x10 pc : [<00000000>] lr : [<c02ace88>] psr: 60000093 sp : dedf7eb0 ip : df572634 fp : 00000000 r10: 00000000 r9 : df52e210 r8 : 60000013 r7 : df6a9858 r6 : df52e210 r5 : df6a9858 r4 : df572600 r3 : 00000000 r2 : ffffff98 r1 : df572600 r0 : df6a9868 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 3edf0059 DAC: 00000015 Process rmmod (pid: 923, stack limit = 0xdedf6230) Stack: (0xdedf7eb0 to 0xdedf8000) 7ea0: 00000000 c02adbbc df572580 deced608 7ec0: df572600 df6a9868 df572634 c02aed3c df577c00 c01b8608 00000000 df6be27c 7ee0: 00200200 00100100 bf0162f4 c000e544 dedf6000 00000000 00000000 bf010c00 7f00: bf0162cc bf00159c 00000000 df572980 df52e218 00000001 df5729b8 bf0031d0 [..] [<c02ace88>] (usb_gadget_giveback_request) from [<c02adbbc>] (request_complete+0x64/0x88) [<c02adbbc>] (request_complete) from [<c02aed3c>] (usba_ep_dequeue+0x70/0x128) [<c02aed3c>] (usba_ep_dequeue) from [<bf010c00>] (hidg_unbind+0x50/0x7c [usb_f_hid]) [<bf010c00>] (hidg_unbind [usb_f_hid]) from [<bf00159c>] (remove_config.isra.6+0x98/0x9c [libcomposite]) [<bf00159c>] (remove_config.isra.6 [libcomposite]) from [<bf0031d0>] (__composite_unbind+0x34/0x98 [libcomposite]) [<bf0031d0>] (__composite_unbind [libcomposite]) from [<c02acee0>] (usb_gadget_remove_driver+0x50/0x78) [<c02acee0>] (usb_gadget_remove_driver) from [<c02ad570>] (usb_gadget_unregister_driver+0x64/0x94) [<c02ad570>] (usb_gadget_unregister_driver) from [<bf0160c0>] (hidg_cleanup+0x10/0x34 [g_hid]) [<bf0160c0>] (hidg_cleanup [g_hid]) from [<c0056748>] (SyS_delete_module+0x118/0x19c) [<c0056748>] (SyS_delete_module) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30) Code: bad PC value Signed-off-by:
Songjun Wu <songjun.wu@atmel.com> [nicolas.ferre@atmel.com: reworked the commit message] Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 914a3f3b ("USB: add atmel_usba_udc driver") Signed-off-by:
-
Nicholas Bellinger authored
commit 046ba642 upstream. This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(), which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512 byte sector devices), and for hw_max_sectors is a backend driver dependent value. This limit is problematic because Linux initiators have only recently started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger than 4 MB in size. Currently when this happens, the following message will appear on the target resulting in I/Os being returned with non recoverable status: SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192 Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(), and convert the existing hw_max_sectors into a purely informational attribute used to represent the granuality that backend driver and/or subsystem code is splitting I/Os upon. Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw() to deal with the one special iovec limitiation case. v2 changes: - Drop hw_max_sectors check in sbc_parse_cdb() Reported-by:
Lance Gropper <lance.gropper@qosserver.com> Reported-by:
Stefan Priebe <s.priebe@profihost.ag> Cc: Christoph Hellwig <hch@lst.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
-
Alexander Usyskin authored
commit b13a65ef upstream. H_RST bit in H_CSR register may be found lit before reset is started, for example if preceding reset flow hasn't completed. In that case asserting H_RST will be ignored, therefore we need to clean H_RST bit to start a successful reset sequence. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ kamal: backport to 3.13-stable: dev member access ] Signed-off-by:
-
Arseny Solokha authored
commit 56abcab8 upstream. Commit 8dccddbc ("OHCI: final fix for NVIDIA problems (I hope)") introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development board. The code path that was previously specific to NVIDIA controllers had then become taken for all chips. However, the M5237 installed on the board wedges solid when accessing its base+OHCI_FMINTERVAL register, making it impossible to boot any kernel newer than 3.1.8 on this particular and apparently other similar machines. Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237. The patch is suitable for the -next tree as well as all maintained kernels up to 3.2 inclusive. Signed-off-by:
Arseny Solokha <asolokha@kb.kras.ru> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Alan Stern authored
commit 6d89252a upstream. Commit c3ee9b76 (EHCI: improved logic for isochronous scheduling) introduced the idea of using ehci->last_iso_frame as the origin (or base) for the circular calculations involved in modifying the isochronous schedule. However, the new code it added used ehci->last_iso_frame before the value was properly initialized. This patch rectifies the mistake by moving the initialization lines earlier in iso_stream_schedule(). This fixes Bugzilla #72891. Signed-off-by:
Joe Bryant <tenminjoe@yahoo.com> Tested-by:
Martin Long <martin@longhome.co.uk> Signed-off-by:
-
Reinhard Speyerer authored
commit d80c0d14 upstream. As has been discussed in the thread starting with https://lkml.kernel.org/g/549748e9.d+SiJzqu50f1r4lSAL043YSc@arcor.de Sierra Wireless MC73xx devices with USB VID/PID 0x1199:0x68c0 require the option_send_setup() code to be used on the USB interface for the AT port to make unsolicited response codes work correctly. Move these devices from the qcserial driver where they have been added by commit 70a3615f ("usb: qcserial: add Sierra Wireless MC73xx") to the option driver and add a MC73xx-specific blacklist to ensure that 1. the sendsetup code is not used for the DIAG/DM and NMEA interfaces 2. the option driver does not attach to the QMI/network interfaces Signed-off-by:
Reinhard Speyerer <rspmn@arcor.de> Signed-off-by:
-
David Peterson authored
commit 1ae78a48 upstream. Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks devices. Signed-off-by:
David Peterson <david.peterson@cel.com> Signed-off-by:
-
Trond Myklebust authored
commit 1fc0703a upstream. Currently, our trunking code will check for session trunking, but will fail to detect client id trunking. This is a problem, because it means that the client will fail to recognise that the two connections represent shared state, even if they do not permit a shared session. By removing the check for the server minor id, and only checking the major id, we will end up doing the right thing in both cases: we close down the new nfs_client and fall back to using the existing one. Fixes: 05f4c350 ("NFS: Discover NFSv4 server trunking when mounting") Cc: Chuck Lever <chuck.lever@oracle.com> Tested-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Trond Myklebust authored
commit 06bed7d1 upstream. This commit fixes a race whereby nlmclnt_init() first starts the lockd daemon, and then calls nlm_bind_host() with the expectation that nlmsvc_timeout has already been initialised. Unfortunately, there is no no synchronisation between lockd() and lockd_up() to guarantee that this is the case. Fix is to move the initialisation of nlmsvc_timeout into lockd_create_svc Fixes: 9a1b6bf8 ("LOCKD: Don't call utsname()->nodename...") Cc: Bruce Fields <bfields@fieldses.org> Signed-off-by:
-
Lennart Sorensen authored
commit 572b24e6 upstream. The switch statement of the possible list of SYSCLK1 frequencies is missing a 0 in 4 out of the 7 frequencies. Fixes: fa6d79d2 ("ARM: OMAP: Add initialisation for the real-time counter") Signed-off-by:
Len Sorensen <lsorense@csclub.uwaterloo.ca> Reviewed-by:
Lokesh Vutla <lokeshvutla@ti.com> Acked-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Johan Hovold authored
commit b5122236 upstream. Fix null-pointer dereference during probe if the interface-status completion handler is called before the individual ports have been set up. Fixes: f79b2d0f ("USB: keyspan: fix NULL-pointer dereferences and memory leaks") Reported-by:
Richard <richjunk@pacbell.net> Tested-by:
-
Preston Fick authored
commit 90441b4d upstream. Fixing typo for MeshConnect IDs. The original PID (0x8875) is not in production and is not needed. Instead it has been changed to the official production PID (0x8857). Signed-off-by:
Preston Fick <pffick@gmail.com> Signed-off-by:
-
Fabio Estevam authored
commit 7a87e9cb upstream. From Documentation/devicetree/bindings/clock/imx25-clock.txt: cspi1_ipg 78 cspi2_ipg 79 cspi3_ipg 80 , so fix the SPI1 clocks accordingly to avoid a kernel hang when trying to access SPI1. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Gary Bisson authored
commit 81ef4479 upstream. The post dividers do not work on i.MX6Q rev T0 1.0 so they must be fixed to 1. As the table index was wrong, a divider a of 4 could still be requested which implied the clock not to be set properly. This is the root cause of the HDMI not working at high resolution on rev T0 1.0 of the SoC. Signed-off-by:
Gary Bisson <bisson.gary@gmail.com> Signed-off-by:
-
Bo Shen authored
commit 6785a103 upstream. When receive data, the RXRDY in status register set by hardware after a new packet has been stored in the endpoint FIFO. When it is copied from FIFO, this bit is cleared which make the FIFO can be accessed again. In the receive_data() function, this bit RXRDY has been cleared. So, after the receive_data() function return, this bit should not be cleared again, or else it may cause the accessing FIFO corrupt, which will make the data loss. Fixes: 914a3f3b (USB: add atmel_usba_udc driver) Acked-by:
Bo Shen <voice.shen@atmel.com> Signed-off-by:
-
