- 20 May, 2020 12 commits
-
-
Michael Chan authored
[ Upstream commit bae361c5 ] Improve the slot reset sequence by disabling the device to prevent bad DMAs if slot reset fails. Return the proper result instead of always PCI_ERS_RESULT_RECOVERED to the caller. Fixes: 6316ea6d ("bnxt_en: Enable AER support.") Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Moshe Shemesh authored
[ Upstream commit cece6f43 ] Processing commands by cmd_work_handler() while already in Internal Error State will result in entry leak, since the handler process force completion without doorbell. Forced completion doesn't release the entry and event completion will never arrive, so entry should be released. Fixes: 73dd3a48 ("net/mlx5: Avoid using pending command interface slots") Signed-off-by:
Moshe Shemesh <moshe@mellanox.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Moshe Shemesh authored
[ Upstream commit f3cb3ceb ] mlx5_cmd_flush() will trigger forced completions to all valid command entries. Triggered by an asynch event such as fast teardown it can happen at any stage of the command, including command initialization. It will trigger forced completion and that can lead to completion on an uninitialized command entry. Setting MLX5_CMD_ENT_STATE_PENDING_COMP only after command entry is initialized will ensure force completion is treated only if command entry is initialized. Fixes: 73dd3a48 ("net/mlx5: Avoid using pending command interface slots") Signed-off-by:
-
Michael Chan authored
[ Upstream commit c72cb303 ] The current logic in bnxt_fix_features() will inadvertently turn on both CTAG and STAG VLAN offload if the user tries to disable both. Fix it by checking that the user is trying to enable CTAG or STAG before enabling both. The logic is supposed to enable or disable both CTAG and STAG together. Fixes: 5a9f6b23 ("bnxt_en: Enable and disable RX CTAG and RX STAG VLAN acceleration together.") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit df4953e4 ] syzbot managed to set up sfq so that q->scaled_quantum was zero, triggering an infinite loop in sfq_dequeue() More generally, we must only accept quantum between 1 and 2^18 - 7, meaning scaled_quantum must be in [1, 0x7FFF] range. Otherwise, we also could have a loop in sfq_dequeue() if scaled_quantum happens to be 0x8000, since slot->allot could indefinitely switch between 0 and 0x8000. Fixes: eeaeb068 ("sch_sfq: allow big packets and be fair") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by: syzbot+0251e883fe39e7a0cb0a@syzkaller.appspotmail.com Cc: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8738c85c ] If choke_init() could not allocate q->tab, we would crash later in choke_reset(). BUG: KASAN: null-ptr-deref in memset include/linux/string.h:366 [inline] BUG: KASAN: null-ptr-deref in choke_reset+0x208/0x340 net/sched/sch_choke.c:326 Write of size 8 at addr 0000000000000000 by task syz-executor822/7022 CPU: 1 PID: 7022 Comm: syz-executor822 Not tainted 5.7.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x188/0x20d lib/dump_stack.c:118 __kasan_report.cold+0x5/0x4d mm/kasan/report.c:515 kasan_report+0x33/0x50 mm/kasan/common.c:625 check_memory_region_inline mm/kasan/generic.c:187 [inline] check_memory_region+0x141/0x190 mm/kasan/generic.c:193 memset+0x20/0x40 mm/kasan/common.c:85 memset include/linux/string.h:366 [inline] choke_reset+0x208/0x340 net/sched/sch_choke.c:326 qdisc_reset+0x6b/0x520 net/sched/sch_generic.c:910 dev_deactivate_queue.constprop.0+0x13c/0x240 net/sched/sch_generic.c:1138 netdev_for_each_tx_queue include/linux/netdevice.h:2197 [inline] dev_deactivate_many+0xe2/0xba0 net/sched/sch_generic.c:1195 dev_deactivate+0xf8/0x1c0 net/sched/sch_generic.c:1233 qdisc_graft+0xd25/0x1120 net/sched/sch_api.c:1051 tc_modify_qdisc+0xbab/0x1a00 net/sched/sch_api.c:1670 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5454 netlink_rcv_skb+0x15a/0x410 net/netlink/af_netlink.c:2469 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline] netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329 netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:672 ____sys_sendmsg+0x6bf/0x7e0 net/socket.c:2362 ___sys_sendmsg+0x100/0x170 net/socket.c:2416 __sys_sendmsg+0xec/0x1b0 net/socket.c:2449 do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295 Fixes: 77e62da6 ("sch_choke: drop all packets in queue during reset") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Matt Jolly authored
[ Upstream commit 57c7f2bd ] Add support for Dell Wireless 5816e to drivers/net/usb/qmi_wwan.c Signed-off-by:
Matt Jolly <Kangie@footclan.ninja> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Tariq Toukan authored
[ Upstream commit 40e47307 ] When ENOSPC is set the idx is still valid and gets set to the global MLX4_SINK_COUNTER_INDEX. However gcc's static analysis cannot tell that ENOSPC is impossible from mlx4_cmd_imm() and gives this warning: drivers/net/ethernet/mellanox/mlx4/main.c:2552:28: warning: 'idx' may be used uninitialized in this function [-Wmaybe-uninitialized] 2552 | priv->def_counter[port] = idx; Also, when ENOSPC is returned mlx4_allocate_default_counters should not fail. Fixes: 6de5f7f6 ("net/mlx4_core: Allocate default counter per port") Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Scott Dial authored
[ Upstream commit ab046a5d ] MACsec decryption always occurs in a softirq context. Since the FPU may not be usable in the softirq context, the call to decrypt may be scheduled on the cryptd work queue. The cryptd work queue does not provide ordering guarantees. Therefore, preserving order requires masking out ASYNC implementations of gcm(aes). For instance, an Intel CPU with AES-NI makes available the generic-gcm-aesni driver from the aesni_intel module to implement gcm(aes). However, this implementation requires the FPU, so it is not always available to use from a softirq context, and will fallback to the cryptd work queue, which does not preserve frame ordering. With this change, such a system would select gcm_base(ctr(aes-aesni),ghash-generic). While the aes-aesni implementation prefers to use the FPU, it will fallback to the aes-asm implementation if unavailable. By using a synchronous version of gcm(aes), the decryption will complete before returning from crypto_aead_decrypt(). Therefore, the macsec_decrypt_done() callback will be called before returning from macsec_decrypt(). Thus, the order of calls to macsec_post_decrypt() for the frames is preserved. While it's presumable that the pure AES-NI version of gcm(aes) is more performant, the hybrid solution is capable of gigabit speeds on modest hardware. Regardless, preserving the order of frames is paramount for many network protocols (e.g., triggering TCP retries). Within the MACsec driver itself, the replay protection is tripped by the out-of-order frames, and can cause frames to be dropped. This bug has been present in this code since it was added in v4.6, however it may not have been noticed since not all CPUs have FPU offload available. Additionally, the bug manifests as occasional out-of-order packets that are easily misattributed to other network phenomena. When this code was added in v4.6, the crypto/gcm.c code did not restrict selection of the ghash function based on the ASYNC flag. For instance, x86 CPUs with PCLMULQDQ would select the ghash-clmulni driver instead of ghash-generic, which submits to the cryptd work queue if the FPU is busy. However, this bug was was corrected in v4.8 by commit b30bdfa8, and was backported all the way back to the v3.14 stable branch, so this patch should be applicable back to the v4.6 stable branch. Signed-off-by:
Scott Dial <scott@scottdial.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 14695212 ] My intent was to not let users set a zero drop_batch_size, it seems I once again messed with min()/max(). Fixes: 9d18562a ("fq_codel: add batch ability to fq_codel_drop()") Signed-off-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Julia Lawall authored
[ Upstream commit 86530837 ] In this code, it appears that phyter_clocks is a list head, based on the previous list_for_each, and that clock->list is intended to be a list element, given that it has just been initialized in dp83640_clock_init. Accordingly, switch the arguments to list_add_tail, which takes the list head as the second argument. Fixes: cb646e2b ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by:
-
Matt Jolly authored
commit 78d6de3c upstream. Add support for Dell Wireless 5816e to drivers/usb/serial/qcserial.c Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
- 10 May, 2020 19 commits
-
-
Greg Kroah-Hartman authored
-
Thomas Pedersen authored
commit 30b2f0be upstream. commit 08a5bdde ("mac80211: consider QoS Null frames for STA_NULLFUNC_ACKED") Fixed a bug where we failed to take into account a nullfunc frame can be either non-QoS or QoS. It turns out there is at least one more bug in ieee80211_sta_tx_notify(), introduced in commit 7b6ddeaf ("mac80211: use QoS NDP for AP probing"), where we forgot to check for the QoS variant and so assumed the QoS nullfunc frame never went out Fix this by adding a helper ieee80211_is_any_nullfunc() which consolidates the check for non-QoS and QoS nullfunc frames. Replace existing compound conditionals and add a couple more missing checks for QoS variant. Signed-off-by:
Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200114055940.18502-3-thomas@adapt-ip.comSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit 977dfef4 upstream. The commit 3c6fd1f0 ("ALSA: hda: Add driver blacklist") added a new blacklist for the devices that are known to have empty codecs, and one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f). However, it turned out that the very same PCI SSID is used for the previous model that does have the valid HD-audio codecs and the change broke the sound on it. Since the empty codec problem appear on the certain AMD platform (PCI ID 1022:1487), this patch changes the blacklist matching to both PCI ID and SSID using pci_match_id(). Also, the entry that was removed by the previous fix for ASUS ROG Zenigh II is re-added. Link: https://lore.kernel.org/r/20200424061222.19792-1-tiwai@suse.deSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jere Leppänen authored
commit 12dfd78e upstream. When starting shutdown in sctp_sf_do_dupcook_a(), get the value for SHUTDOWN Cumulative TSN Ack from the new association, which is reconstructed from the cookie, instead of the old association, which the peer doesn't have anymore. Otherwise the SHUTDOWN is either ignored or replied to with an ABORT by the peer because CTSN Ack doesn't match the peer's Initial TSN. Fixes: bdf6fa52 ("sctp: handle association restarts when the socket is closed.") Signed-off-by:
Jere Leppänen <jere.leppanen@nokia.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Marcin Nowakowski authored
commit f7a31b5e upstream. All performance counters on I6400 (odd and even) are capable of counting any of the available events, so drop current logic of using the extra bit to determine which counter to use. Signed-off-by:
Marcin Nowakowski <marcin.nowakowski@imgtec.com> Fixes: 4e88a862 ("MIPS: Add cases for CPU_I6400") Fixes: fd716fca ("MIPS: perf: Fix I6400 event numbers") Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15991/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Chuck Lever authored
commit d698c4a0 upstream. The backchannel code uses rpcrdma_recv_buffer_put to add new reps to the free rep list. This also decrements rb_recv_count, which spoofs the receive overrun logic in rpcrdma_buffer_get_rep. Commit 9b06688b ("xprtrdma: Fix additional uses of spin_lock_irqsave(rb_lock)") replaced the original open-coded list_add with a call to rpcrdma_recv_buffer_put(), but then a year later, commit 05c97466 ("xprtrdma: Fix receive buffer accounting") added rep accounting to rpcrdma_recv_buffer_put. It was an oversight to let the backchannel continue to use this function. The fix this, let's combine the "add to free list" logic with rpcrdma_create_rep. Also, do not allocate RPCRDMA_MAX_BC_REQUESTS rpcrdma_reps in rpcrdma_buffer_create and then allocate additional rpcrdma_reps in rpcrdma_bc_setup_reps. Allocating the extra reps during backchannel set-up is sufficient. Fixes: 05c97466 ("xprtrdma: Fix receive buffer accounting") Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Doug Berger authored
[ Upstream commit 3554e54a ] The driver is designed to drop Rx packets and reclaim the buffers when an allocation fails, and the network interface needs to safely handle this packet loss. Therefore, an allocation failure of Rx SKBs is relatively benign. However, the output of the warning message occurs with a high scheduling priority that can cause excessive jitter/latency for other high priority processing. This commit suppresses the warning messages to prevent scheduling problems while retaining the failure count in the statistics of the network interface. Signed-off-by:
Doug Berger <opendmb@gmail.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Doug Berger authored
[ Upstream commit ecaeceb8 ] The driver is designed to drop Rx packets and reclaim the buffers when an allocation fails, and the network interface needs to safely handle this packet loss. Therefore, an allocation failure of Rx SKBs is relatively benign. However, the output of the warning message occurs with a high scheduling priority that can cause excessive jitter/latency for other high priority processing. This commit suppresses the warning messages to prevent scheduling problems while retaining the failure count in the statistics of the network interface. Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 5990cdee ] 0day reports over and over on an powerpc randconfig with clang: lib/mpi/generic_mpih-mul1.c:37:13: error: invalid use of a cast in a inline asm context requiring an l-value: remove the cast or build with -fheinous-gnu-extensions Remove the superfluous casts, which have been done previously for x86 and arm32 in commit dea632ca ("lib/mpi: fix build with clang") and commit 7b7c1df2 ("lib/mpi/longlong.h: fix building with 32-bit x86"). Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://github.com/ClangBuiltLinux/linux/issues/991 Link: https://lore.kernel.org/r/20200413195041.24064-1-natechancellor@gmail.comSigned-off-by:
-
Florian Fainelli authored
[ Upstream commit 6344dbde ] When asking the ARL to read a MAC address, we will get a number of bins returned in a single read. Out of those bins, there can essentially be 3 states: - all bins are full, we have no space left, and we can either replace an existing address or return that full condition - the MAC address was found, then we need to return its bin index and modify that one, and only that one - the MAC address was not found and we have a least one bin free, we use that bin index location then The code would unfortunately fail on all counts. Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by:
-
Jeremie Francois (on alpha) authored
[ Upstream commit e461bc9f ] Sed broke on some strings as it used colon as a separator. I made it more robust by using \001, which is legit POSIX AFAIK. E.g. ./config --set-str CONFIG_USBNET_DEVADDR "de:ad:be:ef:00:01" failed with: sed: -e expression #1, char 55: unknown option to `s' Signed-off-by:
Jeremie Francois (on alpha) <jeremie.francois@gmail.com> Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Ronnie Sahlberg authored
[ Upstream commit fada37f6 ] We use a spinlock while we are reading and accessing the destination address for a server. We need to also use this spinlock to protect when we are modifying this address from reconn_set_ipaddr(). Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
Jeff Layton <jlayton@kernel.org> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Julien Beraud authored
[ Upstream commit 91a2559c ] In fine adjustement mode, which is the current default, the sub-second increment register is the number of nanoseconds that will be added to the clock when the accumulator overflows. At each clock cycle, the value of the addend register is added to the accumulator. Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the frequency of the ptp clock actually is. The adjustment is then done on the addend register, only incrementing every X clock cycles X being the ratio between 50MHz and ptp_clock_rate (addend = 2^32 * 50MHz/ptp_clock_rate). This causes the following issues : - In case the frequency of the ptp clock is inferior or equal to 50MHz, the addend value calculation will overflow and the default addend value will be set to 0, causing the clock to not work at all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32). - The resolution of the timestamping clock is limited to 20ns while it is not needed, thus limiting the accuracy of the timestamping to 20ns. Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate. It will allow to reach the minimum possible frequency for ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the sub-second-increment to a higher value. For instance, for 25MHz, it gives ssinc = 80ns and default_addend = 2^31. It will also allow to use a lower value for sub-second-increment, thus improving the timestamping accuracy with frequencies higher than 100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend = 2^31. v1->v2: - Remove modifications to the calculation of default addend, which broke compatibility with clock frequencies for which 2000000000 / ptp_clk_freq is not an integer. - Modify description according to discussions. Signed-off-by:
Julien Beraud <julien.beraud@orolia.com> Signed-off-by:
-
Xiyu Yang authored
[ Upstream commit 7717cbec ] i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the refcount of the "notif_urb". When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb" becomes invalid, so the refcount should be decreased to keep refcount balanced. The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which forget to decrease the refcnt increased by usb_get_urb(), causing a refcnt leak. Fix this issue by calling usb_put_urb() before the i2400mu_bus_bm_wait_for_ack() returns. Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by:
Xin Tan <tanxin.ctf@gmail.com> Signed-off-by:
-
Sebastian Reichel authored
[ Upstream commit aa781273 ] As mentioned slightly out of patch context in the code, there is no reset routine for the chip. On boards where the chip is supplied by a fixed regulator, it might not even be resetted during (e.g. watchdog) reboot and can be in any state. If the device is probed with VAG enabled, the driver's probe routine will generate a loud pop sound when ANA_POWER is being programmed. Avoid this by properly disabling just the VAG bit and waiting the required power down time. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by:
Fabio Estevam <festivem@gmail.com> Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Tyler Hicks authored
[ Upstream commit b87080ea ] After successfully running the IPC msgque test once, subsequent runs result in a test failure: $ sudo ./run_kselftest.sh TAP version 13 1..1 # selftests: ipc: msgque # Failed to get stats for IPC queue with id 0 # Failed to dump queue: -22 # Bail out! # # Pass 0 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0 not ok 1 selftests: ipc: msgque # exit=1 The dump_queue() function loops through the possible message queue index values using calls to msgctl(kern_id, MSG_STAT, ...) where kern_id represents the index value. The first time the test is ran, the initial index value of 0 is valid and the test is able to complete. The index value of 0 is not valid in subsequent test runs and the loop attempts to try index values of 1, 2, 3, and so on until a valid index value is found that corresponds to the message queue created earlier in the test. The msgctl() syscall returns -1 and sets errno to EINVAL when invalid index values are used. The test failure is caused by incorrectly comparing errno to -EINVAL when cycling through possible index values. Fix invalid test failures on subsequent runs of the msgque test by correctly comparing errno values to a non-negated EINVAL. Fixes: 3a665531 ("selftests: IPC message queue copy feature test") Signed-off-by:
Tyler Hicks <tyhicks@linux.microsoft.com> Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 28535877 ] It should use ad7797_attribute_group in ad7797_info, according to commit ("iio:ad7793: Add support for the ad7796 and ad7797"). Scale is fixed for the ad7796 and not programmable, hence should not have the scale_available attribute. Fixes: fd1a8b91 ("iio:ad7793: Add support for the ad7796 and ad7797") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Alexey Kardashevskiy authored
commit dead1c84 upstream. The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing which reads "assigned-addresses" of every PCI device and initializes the device resources. However if the property is missing or zero sized, then there is no fallback of any kind and the PCI resources remain undiscovered, i.e. pdev->resource[] array remains empty. This adds a fallback which parses the "reg" property in pretty much same way except it marks resources as "unset" which later make Linux assign those resources proper addresses. This has an effect when: 1. a hypervisor failed to assign any resource for a device; 2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try assigning a resource. Neither is likely to happen under PowerVM. Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by:
-
Jia He authored
commit 0b841030 upstream. Ning Bo reported an abnormal 2-second gap when booting Kata container [1]. The unconditional timeout was caused by VSOCK_DEFAULT_CONNECT_TIMEOUT of connecting from the client side. The vhost vsock client tries to connect an initializing virtio vsock server. The abnormal flow looks like: host-userspace vhost vsock guest vsock ============== =========== ============ connect() --------> vhost_transport_send_pkt_work() initializing | vq->private_data==NULL | will not be queued V schedule_timeout(2s) vhost_vsock_start() <--------- device ready set vq->private_data wait for 2s and failed connect() again vq->private_data!=NULL recv connecting pkt Details: 1. Host userspace sends a connect pkt, at that time, guest vsock is under initializing, hence the vhost_vsock_start has not been called. So vq->private_data==NULL, and the pkt is not been queued to send to guest 2. Then it sleeps for 2s 3. After guest vsock finishes initializing, vq->private_data is set 4. When host userspace wakes up after 2s, send connecting pkt again, everything is fine. As suggested by Stefano Garzarella, this fixes it by additional kicking the send_pkt worker in vhost_vsock_start once the virtio device is started. This makes the pending pkt sent again. After this patch, kata-runtime (with vsock enabled) boot time is reduced from 3s to 1s on a ThunderX2 arm64 server. [1] https://github.com/kata-containers/runtime/issues/1917Reported-by:
Ning Bo <n.b@live.com> Suggested-by:
Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:
Jia He <justin.he@arm.com> Link: https://lore.kernel.org/r/20200501043840.186557-1-justin.he@arm.comSigned-off-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
-
- 05 May, 2020 9 commits
-
-
Greg Kroah-Hartman authored
-
Vasily Averin authored
commit 933db733 upstream. qxl_release should not be accesses after qxl_push_*_ring_release() calls: userspace driver can process submitted command quickly, move qxl_release into release_ring, generate interrupt and trigger garbage collector. It can lead to crashes in qxl driver or trigger memory corruption in some kmalloc-192 slab object Gerd Hoffmann proposes to swap the qxl_release_fence_buffer_objects() + qxl_push_{cursor,command}_ring_release() calls to close that race window. cc: stable@vger.kernel.org Fixes: f64122c1 ("drm: add new QXL driver. (v1.4)") Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Link: http://patchwork.freedesktop.org/patch/msgid/fa17b338-66ae-f299-68fe-8d32419d9071@virtuozzo.comSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com> [backported to v4.9-stable] Signed-off-by:
-
Paul Moore authored
commit fb739741 upstream. Fix the SELinux netlink_send hook to properly handle multiple netlink messages in a single sk_buff; each message is parsed and subject to SELinux access control. Prior to this patch, SELinux only inspected the first message in the sk_buff. Cc: stable@vger.kernel.org Reported-by:
Dmitry Vyukov <dvyukov@google.com> Reviewed-by:
Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Andy Shevchenko authored
commit b9f96020 upstream. Under some circumstances, i.e. when test is still running and about to time out and user runs, for example, grep -H . /sys/module/dmatest/parameters/* the iterations parameter is not respected and test is going on and on until user gives echo 0 > /sys/module/dmatest/parameters/run This is not what expected. The history of this bug is interesting. I though that the commit 2d88ce76 ("dmatest: add a 'wait' parameter") is a culprit, but looking closer to the code I think it simple revealed the broken logic from the day one, i.e. in the commit 0a2ff57d ("dmaengine: dmatest: add a maximum number of test iterations") which adds iterations parameter. So, to the point, the conditional of checking the thread to be stopped being first part of conjunction logic prevents to check iterations. Thus, we have to always check both conditions to be able to stop after given iterations. Since it wasn't visible before second commit appeared, I add a respective Fixes tag. Fixes: 2d88ce76 ("dmatest: add a 'wait' parameter") Cc: Dan Williams <dan.j.williams@intel.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.comSigned-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Andreas Gruenbacher authored
commit 7648f939 upstream. nfs3_set_acl keeps track of the acl it allocated locally to determine if an acl needs to be released at the end. This results in a memory leak when the function allocates an acl as well as a default acl. Fix by releasing acls that differ from the acl originally passed into nfs3_set_acl. Fixes: b7fa0554 ("[PATCH] NFS: Add support for NFSv3 ACLs") Reported-by:
Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by:
-
Arnd Bergmann authored
commit 5ce00760 upstream. gcc-10 points out a few instances of suspicious integer arithmetic leading to value truncation: sound/isa/opti9xx/opti92x-ad1848.c: In function 'snd_opti9xx_configure': sound/isa/opti9xx/opti92x-ad1848.c:322:43: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_opti9xx_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow] 322 | (snd_opti9xx_read(chip, reg) & ~(mask)) | ((value) & (mask))) | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~ sound/isa/opti9xx/opti92x-ad1848.c:351:3: note: in expansion of macro 'snd_opti9xx_write_mask' 351 | snd_opti9xx_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff); | ^~~~~~~~~~~~~~~~~~~~~~ sound/isa/opti9xx/miro.c: In function 'snd_miro_configure': sound/isa/opti9xx/miro.c:873:40: error: overflow in conversion from 'int' to 'unsigned char' changes value from '(int)snd_miro_read(chip, 3) & -256 | 240' to '240' [-Werror=overflow] 873 | (snd_miro_read(chip, reg) & ~(mask)) | ((value) & (mask))) | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~ sound/isa/opti9xx/miro.c:1010:3: note: in expansion of macro 'snd_miro_write_mask' 1010 | snd_miro_write_mask(chip, OPTi9XX_MC_REG(3), 0xf0, 0xff); | ^~~~~~~~~~~~~~~~~~~ These are all harmless here as only the low 8 bit are passed down anyway. Change the macros to inline functions to make the code more readable and also avoid the warning. Strictly speaking those functions also need locking to make the read/write pair atomic, but it seems unlikely that anyone would still run into that issue. Fixes: 1841f613 ("[ALSA] Add snd-miro driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200429190216.85919-1-arnd@arndb.deSigned-off-by:
-
Suravee Suthikulpanit authored
commit b74aa02d upstream. Currently, system fails to boot because the legacy interrupt remapping mode does not enable 128-bit IRTE (GA), which is required for x2APIC support. Fix by using AMD_IOMMU_GUEST_IR_LEGACY_GA mode when booting with kernel option amd_iommu_intr=legacy instead. The initialization logic will check GASup and automatically fallback to using AMD_IOMMU_GUEST_IR_LEGACY if GA mode is not supported. Fixes: 3928aa3f ("iommu/amd: Detect and enable guest vAPIC support") Signed-off-by:
Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Link: https://lore.kernel.org/r/1587562202-14183-1-git-send-email-suravee.suthikulpanit@amd.comSigned-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Sean Christopherson authored
commit 5cbf3264 upstream. Use follow_pfn() to get the PFN of a PFNMAP VMA instead of assuming that vma->vm_pgoff holds the base PFN of the VMA. This fixes a bug where attempting to do VFIO_IOMMU_MAP_DMA on an arbitrary PFNMAP'd region of memory calculates garbage for the PFN. Hilariously, this only got detected because the first "PFN" calculated by vaddr_get_pfn() is PFN 0 (vma->vm_pgoff==0), and iommu_iova_to_phys() uses PA==0 as an error, which triggers a WARN in vfio_unmap_unpin() because the translation "failed". PFN 0 is now unconditionally reserved on x86 in order to mitigate L1TF, which causes is_invalid_reserved_pfn() to return true and in turns results in vaddr_get_pfn() returning success for PFN 0. Eventually the bogus calculation runs into PFNs that aren't reserved and leads to failure in vfio_pin_map_dma(). The subsequent call to vfio_remove_dma() attempts to unmap PFN 0 and WARNs. WARNING: CPU: 8 PID: 5130 at drivers/vfio/vfio_iommu_type1.c:750 vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1] Modules linked in: vfio_pci vfio_virqfd vfio_iommu_type1 vfio ... CPU: 8 PID: 5130 Comm: sgx Tainted: G W 5.6.0-rc5-705d787c7fee-vfio+ #3 Hardware name: Intel Corporation Mehlow UP Server Platform/Moss Beach Server, BIOS CNLSE2R1.D00.X119.B49.1803010910 03/01/2018 RIP: 0010:vfio_unmap_unpin+0x2e1/0x310 [vfio_iommu_type1] Code: <0f> 0b 49 81 c5 00 10 00 00 e9 c5 fe ff ff bb 00 10 00 00 e9 3d fe RSP: 0018:ffffbeb5039ebda8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff9a55cbf8d480 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff9a52b771c200 RBP: 0000000000000000 R08: 0000000000000040 R09: 00000000fffffff2 R10: 0000000000000001 R11: ffff9a51fa896000 R12: 0000000184010000 R13: 0000000184000000 R14: 0000000000010000 R15: ffff9a55cb66ea08 FS: 00007f15d3830b40(0000) GS:ffff9a55d5600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000561cf39429e0 CR3: 000000084f75f005 CR4: 00000000003626e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: vfio_remove_dma+0x17/0x70 [vfio_iommu_type1] vfio_iommu_type1_ioctl+0x9e3/0xa7b [vfio_iommu_type1] ksys_ioctl+0x92/0xb0 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x4c/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f15d04c75d7 Code: <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 f7 d8 64 89 01 48 Fixes: 73fa0d10 ("vfio: Type1 IOMMU implementation") Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Alaa Hleihel authored
commit c08cfb2d upstream. Initialize ib_spec on the stack before using it, otherwise we will have garbage values that will break creating default rules with invalid parsing error. Fixes: a37a1a42 ("IB/mlx4: Add mechanism to support flow steering over IB links") Link: https://lore.kernel.org/r/20200413132235.930642-1-leon@kernel.orgSigned-off-by:
Alaa Hleihel <alaa@mellanox.com> Reviewed-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
