- 02 Mar, 2015 18 commits
-
-
Alexander Usyskin authored
commit 663b7ee9 upstream. We might enter the interrupt handler with hw_ready already set, but prior we actually started the reset flow. To soleve this we move the reset release from the interrupt handler to the HW start wait function which is part of the reset sequence. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Alexander Usyskin authored
commit 1ab1e79b upstream. We should mask interrupt set bit when writing back hcsr value in reset bit clean-up. This is refinement for mei: clean reset bit before reset commit b13a65efSigned-off-by:
-
Malcolm Priestley authored
commit 15e1ce33 upstream. A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK but the endpoint otheriwse functions as interrupt. Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Peng Tao authored
commit cb5d04bc upstream. With pgio refactoring in v3.15, .init_read and .init_write can be called with valid pgio->pg_lseg. file layout was fixed at that time by commit c6194271 (pnfs: filelayout: support non page aligned layouts). But the generic helper still needs to be fixed. Signed-off-by:
Peng Tao <tao.peng@primarydata.com> Signed-off-by:
-
Matej Dubovy authored
commit 8f0c304c upstream. Please add support for sub BT chip on the combo card Broadcom 43142A0 (in Lenovo E145), 04ca:2007 /sys/kernel/debug/usb/devices T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=2007 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=28E347EC73BD C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Firmware for 04ca:2007 can be extracted from the latest Lenovo E145 Bluetooth driver for Windows (driver is however described as BCM20702 but contains also firwmare for BCM43142). Search for BCM43142A0_001.001.011.0122.0153.hex within hex files, then it must be converted using hex2hcd utility. Rename file to BCM43142A0-04ca-2007.hcd, then move to /lib/firmware/brcm/. Signed-off-by:
Matej Dubovy <matej.dubovy@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Viresh Kumar authored
commit 6ffae8c0 upstream. In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs to be cleared before calling kobject_put(&policy->kobj) and under cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get() in parallel with it, they can obtain a non-NULL policy from that after kobject_put(&policy->kobj) was executed. Consider this case: Thread A Thread B cpufreq_cpu_get() acquire cpufreq_driver_lock read-per-cpu cpufreq_cpu_data kobject_put(&policy->kobj); kobject_get(&policy->kobj); ... per_cpu(&cpufreq_cpu_data, cpu) = NULL And this will result in a warning like this one: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47 kobject_get+0x41/0x50() Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon ... Call Trace: [<ffffffff81661b14>] dump_stack+0x46/0x58 [<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0 [<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20 [<ffffffff812e16d1>] kobject_get+0x41/0x50 [<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0 [<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0 [<ffffffff810b8cb2>] ? up+0x32/0x50 [<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2 [<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252 [<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0 [<ffffffff81360967>] ? acpi_has_method+0x25/0x40 [<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82 [<ffffffff81089566>] ? move_linked_works+0x66/0x90 [<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7 [<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c [<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22 [<ffffffff8108c910>] process_one_work+0x160/0x410 [<ffffffff8108d05b>] worker_thread+0x11b/0x520 [<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380 [<ffffffff81092421>] kthread+0xe1/0x100 [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0 [<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0 [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0 ---[ end trace 89e66eb9795efdf7 ]--- The actual code flow is as follows: Thread A: Workqueue: kacpi_notify acpi_processor_notify() acpi_processor_ppc_has_changed() cpufreq_update_policy() cpufreq_cpu_get() kobject_get() Thread B: xenbus_thread() xenbus_thread() msg->u.watch.handle->callback() handle_vcpu_hotplug_event() vcpu_hotplug() cpu_down() __cpu_notify(CPU_POST_DEAD..) cpufreq_cpu_callback() __cpufreq_remove_dev_finish() cpufreq_policy_put_kobj() kobject_put() cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data under cpufreq_driver_lock, and once it gets a valid policy it expects it to not be freed until cpufreq_cpu_put() is called. But the race happens when another thread puts the kobject first and updates cpufreq_cpu_data before or later. And so the first thread gets a valid policy structure and before it does kobject_get() on it, the second one has already done kobject_put(). Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that too under locks. Reported-by:
Ethan Zhao <ethan.zhao@oracle.com> Reported-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Stefan Agner authored
commit 5f1437f6 upstream. When the UART is in DMA receive mode (RDMAS set) and one character just arrived while another interrupt is handled (e.g. TX), the RDRF (receiver data register full flag) is set due to the water level of 1. But since the DMA will take care of this character, there is no need to handle it by calling lpuart_prepare_rx. Handling it leads to adding the RX timeout timer twice: [ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable] [ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd [ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback [ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788 [ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t [ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd [ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1 [ 74.373960] LR is at lpuart_int+0x15c/0x3d8 [ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193 [ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c [ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013 [ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210 [ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344 [ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015 [ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230) ... Solve this by only execute the receiver path (lpuart_prepare_rx) if the DMA receive mode (RDMAS) is not set. Also, make sure the flag is cleared on initialization, in case it has been left set. This can be best reproduced using UART as a serial console, then running top while dd'ing data into the terminal. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Stefan Agner authored
commit 4a8588a1 upstream. If the serial port gets closed while a RX transfer is in progress, the timer might fire after the serial port shutdown finished. This leads in a NULL pointer dereference: [ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 7.516590] pgd = 86348000 [ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000 [ 7.526145] Internal error: Oops: 17 [#1] ARM [ 7.530611] Modules linked in: [ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778 [ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree) [ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000 [ 7.553392] PC is at lpuart_timer_func+0x24/0xf8 [ 7.558127] LR is at lpuart_timer_func+0x20/0xf8 [ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113 [ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc [ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998 [ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210 [ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000 [ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015 [ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230) Setup the timer on UART startup which allows to delete the timer unconditionally on shutdown. This also saves the initialization on each transfer. Signed-off-by:
-
Peter Hurley authored
commit 37480a05 upstream. Commit 26df6d13 ("tty: Add EXTPROC support for LINEMODE") allows a process which has opened a pty master to send _any_ signal to the process group of the pty slave. Although potentially exploitable by a malicious program running a setuid program on a pty slave, it's unknown if this exploit currently exists. Limit to signals actually used. Cc: Theodore Ts'o <tytso@mit.edu> Cc: Howard Chu <hyc@symas.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Nicolas Pitre authored
commit 19e3ae6b upstream. The vcs device's poll/fasync support relies on the vt notifier to signal changes to the screen content. Notifier invocations were missing for changes that comes through the selection interface though. Fix that. Tested with BRLTTY 5.2. Signed-off-by:
Nicolas Pitre <nico@linaro.org> Cc: Dave Mielke <dave@mielke.cc> Signed-off-by:
-
Luciano Coelho authored
commit fd66fc1c upstream. When iwl_mvm_power_update_mac() is called, we have already added the mac context, so if this call fails we should remove the mac. Fixes: commit e5e7aa8e ('iwlwifi: mvm: refactor power code') Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com> Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit cd8f4384 upstream. The base address of the scheduler in the device's memory (SRAM) comes from two different sources. The periphery register and the alive notification from the firmware. We have a check in iwl_pcie_tx_start that ensures that they are the same. When we resume from WoWLAN, the firmware may have crashed for whatever reason. In that case, the whole device may be reset which means that the periphery register will hold a meaningless value. When we come to compare trans_pcie->scd_base_addr (which really holds the value we had when we loaded the WoWLAN firmware upon suspend) and the current value of the register, we don't see a match unsurprisingly. Trick the check to avoid a loud yet harmless WARN. Note that when the WoWLAN has crashed, we will see that in iwl_trans_pcie_d3_resume which will let the op_mode know. Once the op_mode is informed that the WowLAN firmware has crashed, it can't do much besides resetting the whole device. Reviewed-by:
-
Luciano Coelho authored
commit 5523d11c upstream. We don't really need to use different mac colors when adding mac contexts, because they're not used anywhere. In fact, the firmware doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401 when we reach that. Remove the color increment to use always zero and avoid reaching 255. Signed-off-by:
-
Alan Stern authored
commit c9919790 upstream. The usb_hcd_unlink_urb() routine in hcd.c contains two possible use-after-free errors. The dev_dbg() statement at the end of the routine dereferences urb and urb->dev even though both structures may have been deallocated. This patch fixes the problem by storing urb->dev in a local variable (avoiding the dereference of urb) and moving the dev_dbg() up before the usb_put_dev() call. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Joe Lawrence <joe.lawrence@stratus.com> Tested-by:
Greg Kroah-Hartman <greg@kroah.com> Signed-off-by:
-
Alan Stern authored
commit 074f9dd5 upstream. Currently the USB stack assumes that all host controller drivers are capable of receiving wakeup requests from downstream devices. However, this isn't true for the isp1760-hcd driver, which means that it isn't safe to do a runtime suspend of any device attached to a root-hub port if the device requires wakeup. This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure and sets the flag in isp1760-hcd. The core is modified to prevent a direct child of the root hub from being put into runtime suspend with wakeup enabled if the flag is set. Signed-off-by:
-
Oliver Neukum authored
commit 7e860a6e upstream. Check the special CDC headers for a plausible minimum length. Another big operating systems ignores such garbage. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Reviewed-by:
Adam Lee <adam8157@gmail.com> Tested-by:
-
Jeff Layton authored
commit 6ffa30d3 upstream. Bruce reported seeing this warning pop when mounting using v4.1: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90 Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014 0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78 0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000 Call Trace: [<ffffffff8186ac78>] dump_stack+0x4c/0x65 [<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0 [<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70 [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90 [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90 [<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0 [<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430 [<ffffffff810d941e>] ? groups_alloc+0x3e/0x130 [<ffffffff810d941e>] groups_alloc+0x3e/0x130 [<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc] [<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc] [<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc] [<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc] [<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4] [<ffffffff810ff970>] ? wait_woken+0xc0/0xc0 [<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4] [<ffffffff810d45bf>] kthread+0x11f/0x140 [<ffffffff810ea815>] ? local_clock+0x15/0x30 [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250 [<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0 [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250 ---[ end trace 675220a11e30f4f2 ]--- nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE, which is just wrong. Fix that by finishing the wait immediately if we've found that the list has something on it. Also, we don't expect this kthread to accept signals, so we should be using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up hung task warnings from the watchdog, so have the schedule_timeout wake up every 60s if there's no callback activity. Reported-by:
"J. Bruce Fields" <bfields@fieldses.org> Signed-off-by:
Jeff Layton <jlayton@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Antti Palosaari authored
commit f1ecc5d1 upstream. w_scan complains about missing symbol rate limits: This dvb driver is *buggy*: the symbol rate limits are undefined - please report to linuxtv.org Chip supports 1 to 7.2 MSymbol/s on DVB-C. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
- 24 Feb, 2015 22 commits
-
-
Dmitry Eremin-Solenikov authored
commit e461894d upstream. StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset by entering the sleep mode. After we have resumed, there is little point in having that bit enabled. Moreover, if this bit is set before reboot, the bootloader can become confused. Thus clear the SMR bit on resume just before clearing the scratchpad (resume address) register. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Marcin Wojtas authored
commit a39128bc upstream. According to erratum 'ERR-7878951' Armada 38x SDHCI controller has different capabilities than the ones shown in its registers: - it doesn't support the voltage switching: it can work either with 3.3V or 1.8V supply - it doesn't support the SDR104 mode - SDR50 mode doesn't need tuning The SDHCI_QUIRK_MISSING_CAPS quirk is used for updating the capabilities accordingly. [gregory.clement@free-electrons.com: port from 3.10] Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Gregory CLEMENT authored
commit d4b803c5 upstream. According to erratum 'FE-2946959' both SDR50 and DDR50 modes require specific clock adjustments in SDIO3 Configuration register. However, this register was not part of the device tree binding. Even if the binding can (and will) be extended we still need handling the case where this register was not available. In this case we use the SDHCI_QUIRK_MISSING_CAPS quirk remove them from the capabilities. This commit is based on the work done by Marcin Wojtas<mw@semihalf.com> Fixes: 5491ce3f ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Signed-off-by:
-
Jisheng Zhang authored
commit 14460dba upstream. Current code checks "clk_delay_cycles > 0" to know whether the optional "mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't touch clk_delay_cycles if the property is not set. And type of clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a random value. This patch fix this problem by check the return value of of_property_read_u32() to know whether the optional clk-delay-cycles is set or not. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Ian Abbott authored
commit 42b8ce6f upstream. `do_cmd_ioctl()` in "comedi_fops.c" handles the `COMEDI_CMD` ioctl. This returns `-EAGAIN` if it has copied a modified `struct comedi_cmd` back to user-space. (This occurs when the low-level Comedi driver's `do_cmdtest()` handler returns non-zero to indicate a problem with the contents of the `struct comedi_cmd`, or when the `struct comedi_cmd` has the `CMDF_BOGUS` flag set.) `compat_cmd()` in "comedi_compat32.c" handles the 32-bit compatible version of the `COMEDI_CMD` ioctl. Currently, it never copies a 32-bit compatible version of `struct comedi_cmd` back to user-space, which is at odds with the way the regular `COMEDI_CMD` ioctl is handled. To fix it, change `compat_cmd()` to copy a 32-bit compatible version of the `struct comedi_cmd` back to user-space when the main ioctl handler returns `-EAGAIN`. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Reviewed-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 24727b45 upstream. Driver forgot to unregister power supply if request_threaded_irq() failed in probe(). In such case the memory associated with power supply leaked. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: a830d28b ("power_supply: Enable battery-charger for 88pm860x") Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
-
Jisheng Zhang authored
commit 3bb10f60 upstream. This patch is to fix a race condition that may cause an unhandled irq, which results in big sdhci interrupt numbers and endless "mmc1: got irq while runtime suspended" msgs before v3.15. Consider following scenario: CPU0 CPU1 sdhci_pxav3_runtime_suspend() spin_lock_irqsave(&host->lock, flags); sdhci_irq() spining on the &host->lock host->runtime_suspended = true; spin_unlock_irqrestore(&host->lock, flags); get the &host->lock runtime_suspended is true now return IRQ_NONE; Fix this race by using the core sdhci.c supplied sdhci_runtime_suspend_host() in runtime suspend hook which will disable card interrupts. We also use the sdhci_runtime_resume_host() in the runtime resume hook accordingly. Signed-off-by:
-
Sebastian Hesselbarth authored
commit 20d5a703 upstream. NULL-checking a struct clk it not only wrong but also not required as for PXAv3 driver the corresponding clock is mandatory. Remove the checks from sdhci_pxav3_runtime_{suspend,resume}. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by:
-
Soren Brinkmann authored
commit 3dccfecd upstream. The CPU_2X clock does not have a classical in-kernel user, but is, amongst other things, required for OCM and debug access. Make sure this clock is not mistakenly disabled during boot up by enabling it in the platform's clock driver. Fixes: 0ee52b15 'clk: zynq: Add clock controller driver' Signed-off-by:
Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Marcel Holtmann authored
commit d049f4e5 upstream. The Dynex/Insignia USB dongles are Broadcom BCM20702B0 based and require firmware update before operation. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=19ff ProdID=0239 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Since this is an unsual USB vendor ID (0x19ff), these dongles are added via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for mainstream Broadcom based dongles. The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex which needs to be converted using hex2hcd utility and then installed as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully operational. Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=2000 lmp_ver=06 lmp_subver=410e Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=222d lmp_ver=06 lmp_subver=410e With this firmware the device reports support for connectionless slave broadcast (master and slave) feature used by 3D Glasses and TVs. < HCI Command: Read Local Extended Features (0x04|0x0004) plen 1 Page: 2 > HCI Event: Command Complete (0x0e) plen 14 Read Local Extended Features (0x04|0x0004) ncmd 1 Status: Success (0x00) Page: 2/2 Features: 0x0f 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Connectionless Slave Broadcast - Master Connectionless Slave Broadcast - Slave Synchronization Train Synchronization Scan However there are some flaws with this feature. The Set Event Mask Page 2 command is actually not supported and with that all connectionless slave broadcast events are always enabled. < HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8 Mask: 0x00000000000f0000 Synchronization Train Received Connectionless Slave Broadcast Receive Connectionless Slave Broadcast Timeout Truncated Page Complete > HCI Event: Command Complete (0x0e) plen 4 Set Event Mask Page 2 (0x03|0x0063) ncmd 1 Status: Unknown HCI Command (0x01) In addition the Synchronization Train Received event is actually broken on this controller. It mixes up the order of parameters. According to the Bluetooth Core specification the fields are like this: struct hci_ev_sync_train_received { __u8 status; bdaddr_t bdaddr; __le32 offset; __u8 map[10]; __u8 lt_addr; __le32 instant; __le16 interval; __u8 service_data; } __packed; This controller however sends the service_data as 5th parameter instead of having it as last parameter. struct hci_ev_sync_train_received { __u8 status; bdaddr_t bdaddr; __le32 offset; __u8 map[10]; __u8 service_data; __u8 lt_addr; __le32 instant; __le16 interval; } __packed; So anybody trying to use this hardware for utilizing connectionless slave broadcast receivers (aka 3D Glasses), be warned about this shortcoming. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Heinrich Siebmanns authored
commit 6029ddc2 upstream. This requires the flag BTUSB_BCM_PATCHRAM to work. Relevant details from /sys/kernel/debug/usb/devices for my device: T: Bus=03 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e031 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=3859F9CD2AEE C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) The firmware was extracted from a Windows 7 32-bit installation and converted from 'hex' to 'hcd' for use in Linux. The firmware is named "BCM20702A0_001.001.024.0156.0204.hex" and is located in "%SYSTEMROOT%\system32\drivers\" (md5 d126e6c4e0e669d76c38cf9377f76b7f) (sha1 145d1850b2785a953233b409e7ff77786927c7d2) The firmware file is also available as a download at http://support.ts.fujitsu.com/Download/ contained in "FTS_WIDCOMMBluetoothSoftware_6309000_1072149.zip" Search for the file Win32/bcbtums-win7x86-brcm.inf in the archive, look for the vendor and product ID of your adapter, see the section 'devices' in that file to find out what device name it uses. See the device entry in the inf file (in my case it was 'RAMUSBE031') to find out which hex file you need to convert to hcd for upload 'hcd' file should be placed at "brcm/BCM20702A0-0489-e031.hcd" inside the firmware directory (e.g. "/lib/firmware") Signed-off-by:
Heinrich Siebmanns <harv@gmx.de> Signed-off-by:
-
Fabio K authored
commit a86c02ea upstream. This variant requires the flag BTUSB_BCM_PATCHRAM to work. Relevant details from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3404 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=240A646F1XXX C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) The firmware was extracted from a Windows 8.1 64-bit installation and converted from 'hex' to 'hcd' for use in Linux. Under Windows it also identifies itself as BCM20702A0, but the firmware is named "BCM20702A1_001.002.014.1315.1356.hex" and is located in "%SYSTEMROOT%\system32\drivers\" (md5 67cf6bfdae61c4bb819a66da984f7913) (sha1 5f74cc6a9a3bf19ee0f8c3d01e4be34c609b188f) The same firmware file is also available as a download at http://www.asrock.com/mb/Intel/Z87E-ITX/?cat=Download&os=All marked as "Bluetooth driver ver:12.0.0.7820" 'hcd' file should be placed at "brcm/BCM20702A0-13d3-3404.hcd" inside the firmware directory (e.g. "/lib/firmware") Signed-off-by:
Fabio K <healthkit@gmail.com> Signed-off-by:
-
Lennart Sorensen authored
commit a6f03312 upstream. Added the USB serial console device ID for Siemens Ruggedcom devices which have a USB port for their serial console. Signed-off-by:
Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Michel Dänzer authored
commit 16b036af upstream. If the image size would ever read as 0, pci_get_rom_size() could keep processing the same image over and over again. Exit the loop if we ever read a length of zero. This fixes a soft lockup on boot when the radeon driver calls pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card. [bhelgaas: changelog, reference] Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973Reported-by:
Federico <federicotg@gmail.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Hans de Goede authored
commit 4690555e upstream. Since kernel 3.14 the backlight control has been broken on various Samsung Atom based netbooks. This has been bisected and this problem happens since commit b35684b8 ("drm/i915: do full backlight setup at enable time") This has been reported and discussed in detail here: http://lists.freedesktop.org/archives/intel-gfx/2014-July/049395.html Unfortunately no-one has been able to fix this. This only affects Samsung Atom netbooks, and the Linux kernel and the BIOS of those laptops have never worked well together. All affected laptops already have a quirk to avoid using the standard acpi-video interface and instead use the samsung specific SABI interface which samsung-laptop uses. It seems that recent fixes to the i915 driver have also broken backlight control through the SABI interface. The intel_backlight driver OTOH works fine, and also allows for finer grained backlight control. So add a new use_native_backlight quirk, and replace the broken_acpi_video quirk with this quirk for affected models. This new quirk disables acpi-video as before and also stops samsung-laptop from registering the SABI based samsung_laptop backlight interface, leaving only the working intel_backlight interface. This commit enables this new quirk for 3 models which are known to be affected, chances are that it needs to be used on other models too. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1094948 # N145P BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1115713 # N250P Reported-by: Bertrik Sikken <bertrik@sikken.nl> # N150P Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
David Hildenbrand authored
commit 428d53be upstream. We have to delete the allocated interrupt info if __inject_vm() fails. Otherwise user space can keep flooding kvm with floating interrupts and provoke more and more memory leaks. Reported-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Reviewed-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
-
David Hildenbrand authored
commit 0ac96caf upstream. The hrtimer that handles the wait with enabled timer interrupts should not be disturbed by changes of the host time. This patch changes our hrtimer to be based on a monotonic clock. Signed-off-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
-
David Sterba authored
commit 5efa0490 upstream. This has been confusing people for too long, the message is really just informative. Signed-off-by:
David Sterba <dsterba@suse.cz> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Dave Chinner authored
commit 3443a3bc upstream. When the superblock is modified in a transaction, the commonly modified fields are not actually copied to the superblock buffer to avoid the buffer lock becoming a serialisation point. However, there are some other operations that modify the superblock fields within the transaction that don't directly log to the superblock but rely on the changes to be applied during the transaction commit (to minimise the buffer lock hold time). When we do this, we fail to mark the buffer log item as being a superblock buffer and that can lead to the buffer not being marked with the corect type in the log and hence causing recovery issues. Fix it by setting the type correctly, similar to xfs_mod_sb()... Tested-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Dave Chinner authored
commit fe22d552 upstream. Conversion from local to extent format does not set the buffer type correctly on the new extent buffer when a symlink data is moved out of line. Fix the symlink code and leave a comment in the generic bmap code reminding us that the format-specific data copy needs to set the destination buffer type appropriately. Tested-by:
-
Dave Chinner authored
commit f19b872b upstream. This leads to log recovery throwing errors like: XFS (md0): Mounting V5 Filesystem XFS (md0): Starting recovery (logdev: internal) XFS (md0): Unknown buffer type 0! XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1 ffff8800ffc53800: 58 41 47 49 ..... Which is the AGI buffer magic number. Ensure that we set the type appropriately in both unlink list addition and removal. Tested-by:
-
Dave Chinner authored
commit 0d612fb5 upstream. Jan Kara reported that log recovery was finding buffers with invalid types in them. This should not happen, and indicates a bug in the logging of buffers. To catch this, add asserts to the buffer formatting code to ensure that the buffer type is in range when the transaction is committed. We don't set a type on buffers being marked stale - they are not going to get replayed, the format item exists only for recovery to be able to prevent replay of the buffer, so the type does not matter. Hence that needs special casing here. Reported-by:
-
