This is the initial VF PCI driver framework for the new
pds_vdpa VF device, which will work in conjunction with an
auxiliary_bus client of the pds_core driver.  This does the
very basics of registering for the new VF device, setting
up debugfs entries, and registering with devlink.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Virtual Interfaces (VIFs) supported by the DSC's
configuration (vDPA, Eth, RDMA, etc) are reported in the
dev_ident struct and made visible in debugfs.  At this point
only vDPA is supported in this driver so we only setup
devices for that feature.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in the support for doing firmware updates.  Of the two
main banks available, a and b, this updates the one not in
use and then selects it for the next boot.

Example:
    devlink dev flash pci/0000:b2:00.0 \
	    file pensando/dsc_fw_1.63.0-22.tar
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the service routines for submitting and processing
the adminq messages and for handling notifyq events.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set up the basic adminq and notifyq queue structures.  These are
used mostly by the client drivers for feature configuration.
These are essentially the same adminq and notifyq as in the
ionic driver.

Part of this includes querying for device identity and FW
information, so we can make that available to devlink dev info.

  $ devlink dev info pci/0000:b5:00.0
  pci/0000:b5:00.0:
    driver pds_core
    serial_number FLM18420073
    versions:
        fixed:
          asic.id 0x0
          asic.rev 0x0
        running:
          fw 1.51.0-73
        stored:
          fw.goldfw 1.15.9-C-22
          fw.mainfwa 1.60.0-73
          fw.mainfwb 1.60.0-57
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink health reporting on top of our fw watchdog.

Example:
  # devlink health show pci/0000:2b:00.0 reporter fw
  pci/0000:2b:00.0:
    reporter fw
      state healthy error 0 recover 0
  # devlink health diagnose pci/0000:2b:00.0 reporter fw
   Status: healthy State: 1 Generation: 0 Recoveries: 0
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in the periodic health check and the related workqueue,
as well as the handlers for when a FW reset is seen.

The firmware is polled every 5 seconds to be sure that it is
still alive and that the FW generation didn't change.

The alive check looks to see that the PCI bus is still readable
and the fw_status still has the RUNNING bit on.  If not alive,
the driver stops activity and tears things down.  When the FW
recovers and the alive check again succeeds, the driver sets
back up for activity.

The generation check looks at the fw_generation to see if it
has changed, which can happen if the FW crashed and recovered
or was updated in between health checks.  If changed, the
driver counts that as though the alive test failed and forces
the fw_down/fw_up cycle.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The devcmd interface is the basic connection to the device through the
PCI BAR for low level identification and command services.  This does
the early device initialization and finds the identity data, and adds
devcmd routines to be used by later driver bits.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the initial PCI driver framework for the new pds_core device
driver and its family of devices.  This does the very basics of
registering for the new PF PCI device 1dd8:100c, setting up debugfs
entries, and registering with devlink.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
bridge: Add per-{Port, VLAN} neighbor suppression

Background
==========

In order to minimize the flooding of ARP and ND messages in the VXLAN
network, EVPN includes provisions [1] that allow participating VTEPs to
suppress such messages in case they know the MAC-IP binding and can
reply on behalf of the remote host. In Linux, the above is implemented
in the bridge driver using a per-port option called "neigh_suppress"
that was added in kernel version 4.15 [2].

Motivation
==========

Some applications use ARP messages as keepalives between the application
nodes in the network. This works perfectly well when two nodes are
connected to the same VTEP. When a node goes down it will stop
responding to ARP requests and the other node will notice it
immediately.

However, when the two nodes are connected to different VTEPs and
neighbor suppression is enabled, the local VTEP will reply to ARP
requests even after the remote node went down, until certain timers
expire and the EVPN control plane decides to withdraw the MAC/IP
Advertisement route for the address. Therefore, some users would like to
be able to disable neighbor suppression on VLANs where such applications
reside and keep it enabled on the rest.

Implementation
==============

The proposed solution is to allow user space to control neighbor
suppression on a per-{Port, VLAN} basis, in a similar fashion to other
per-port options that gained per-{Port, VLAN} counterparts such as
"mcast_router". This allows users to benefit from the operational
simplicity and scalability associated with shared VXLAN devices (i.e.,
external / collect-metadata mode), while still allowing for per-VLAN/VNI
neighbor suppression control.

The user interface is extended with a new "neigh_vlan_suppress" bridge
port option that allows user space to enable per-{Port, VLAN} neighbor
suppression on the bridge port. When enabled, the existing
"neigh_suppress" option has no effect and neighbor suppression is
controlled using a new "neigh_suppress" VLAN option. Example usage:

 # bridge link set dev vxlan0 neigh_vlan_suppress on
 # bridge vlan add vid 10 dev vxlan0
 # bridge vlan set vid 10 dev vxlan0 neigh_suppress on

Testing
=======

Tested using existing bridge selftests. Added a dedicated selftest in
the last patch.

Patchset overview
=================

Patches #1-#5 are preparations.

Patch #6 adds per-{Port, VLAN} neighbor suppression support to the
bridge's data path.

Patches #7-#8 add the required netlink attributes to enable the feature.

Patch #9 adds a selftest.

iproute2 patches can be found here [3].

Changelog
=========

Since RFC [4]:

No changes.

[1] https://www.rfc-editor.org/rfc/rfc7432#section-10
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a42317785c898c0ed46db45a33b0cc71b671bf29
[3] https://github.com/idosch/iproute2/tree/submit/neigh_suppress_v1
[4] https://lore.kernel.org/netdev/20230413095830.2182382-1-idosch@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test cases for bridge neighbor suppression, testing both per-port
and per-{Port, VLAN} neighbor suppression with both ARP and NS packets.

Example truncated output:

 # ./test_bridge_neigh_suppress.sh
 [...]
 Tests passed: 148
 Tests failed:   0
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new bridge port attribute that allows user space to enable
per-{Port, VLAN} neighbor suppression. Example:

 # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
 false
 # bridge link set dev swp1 neigh_vlan_suppress on
 # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
 true
 # bridge link set dev swp1 neigh_vlan_suppress off
 # bridge -d -j -p link show dev swp1 | jq '.[]["neigh_vlan_suppress"]'
 false
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new VLAN attribute that allows user space to set the neighbor
suppression state of the port VLAN. Example:

 # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
 false
 # bridge vlan set vid 10 dev swp1 neigh_suppress on
 # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
 true
 # bridge vlan set vid 10 dev swp1 neigh_suppress off
 # bridge -d -j -p vlan show dev swp1 vid 10 | jq '.[]["vlans"][]["neigh_suppress"]'
 false

 # bridge vlan set vid 10 dev br0 neigh_suppress on
 Error: bridge: Can't set neigh_suppress for non-port vlans.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bridge is not VLAN-aware (i.e., VLAN ID is 0), determine if
neighbor suppression is enabled on a given bridge port solely based on
the existing 'BR_NEIGH_SUPPRESS' flag.

Otherwise, if the bridge is VLAN-aware, first check if per-{Port, VLAN}
neighbor suppression is enabled on the given bridge port using the
'BR_NEIGH_VLAN_SUPPRESS' flag. If so, look up the VLAN and check whether
it has neighbor suppression enabled based on the per-VLAN
'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED' flag.

If the bridge is VLAN-aware, but the bridge port does not have
per-{Port, VLAN} neighbor suppression enabled, then fallback to
determine neighbor suppression based on the 'BR_NEIGH_SUPPRESS' flag.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, there are various places in the bridge data path that check
whether neighbor suppression is enabled on a given bridge port.

As a preparation for per-{Port, VLAN} neighbor suppression, encapsulate
this logic in a function and pass the VLAN ID of the packet as an
argument.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bridge driver gates the neighbor suppression code behind an internal
per-bridge flag called 'BROPT_NEIGH_SUPPRESS_ENABLED'. The flag is set
when at least one bridge port has neighbor suppression enabled.

As a preparation for per-{Port, VLAN} neighbor suppression, make sure
the global flag is also set if per-{Port, VLAN} neighbor suppression is
enabled. That is, when the 'BR_NEIGH_VLAN_SUPPRESS' flag is set on at
least one bridge port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two internal flags that will be used to enable / disable per-{Port,
VLAN} neighbor suppression:

1. 'BR_NEIGH_VLAN_SUPPRESS': A per-port flag used to indicate that
per-{Port, VLAN} neighbor suppression is enabled on the bridge port.
When set, 'BR_NEIGH_SUPPRESS' has no effect.

2. 'BR_VLFLAG_NEIGH_SUPPRESS_ENABLED': A per-VLAN flag used to indicate
that neighbor suppression is enabled on the given VLAN.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which will require br_flood() to potentially suppress ARP /
NS packets on a per-{Port, VLAN} basis.

As a preparation, pass the VLAN ID of the packet as another argument to
br_flood().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bridge does not flood ARP / NS packets for which a reply was sent to
bridge ports that have neighbor suppression enabled.

Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which is going to make it more expensive to check whether
neighbor suppression is enabled since a VLAN lookup will be required.

Therefore, instead of unnecessarily performing this lookup for every
packet, only perform it for ARP / NS packets for which a reply was sent.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Emeel Hakim says:

====================
Support MACsec VLAN

This patch series introduces support for hardware (HW) offload MACsec
devices with VLAN configuration. The patches address both scenarios
where the VLAN header is both the inner and outer header for MACsec.

The changes include:

1. Adding MACsec offload operation for VLAN.
2. Considering VLAN when accessing MACsec net device.
3. Currently offloading MACsec when it's configured over VLAN with
current MACsec TX steering rules would wrongly insert the MACsec sec tag
after inserting the VLAN header. This resulted in an ETHERNET | SECTAG |
VLAN packet when ETHERNET | VLAN | SECTAG is configured. The patche
handles this issue when configuring steering rules.
4. Adding MACsec rx_handler change support in case of a marked skb and a
mismatch on the dst MAC address.

Please review these changes and let me know if you have any feedback or
concerns.

Updates since v1:
- Consult vlan_features when adding NETIF_F_HW_MACSEC.
- Allow grep for the functions.
- Add helper function to get the macsec operation to allow the compiler
  to make some choice.

Updates since v2:
- Don't use macros to allow direct navigattion from mdo functions to its
  implementation.
- Make the vlan_get_macsec_ops argument a const.
- Check if the specific mdo function is available before calling it.
- Enable NETIF_F_HW_MACSEC by default when the lower device has it enabled
  and in case the lower device currently has NETIF_F_HW_MACSEC but disabled
  let the new vlan device also have it disabled.

Updates since v3:
- Split patch ("vlan: Add MACsec offload operations for VLAN interface")
  to prevent mixing generic vlan code changes with driver changes.
- Add mdo_open, stop and stats to support drivers which have those.
- Don't fail if macsec offload operations are available but a specific
  function is not, to support drivers which does not implement all
  macsec offload operations.
- Don't call find_rx_sc twice in the same loop, instead save the result
  in a parameter and re-use it.
- Completely remove _BUILD_VLAN_MACSEC_MDO macro, to prevent returning
  from a macro.
- Reorder the functions inside struct macsec_ops to match the struct
  decleration.

 Updates since v4:
 - Change subject line of ("macsec: Add MACsec rx_handler change support") and adapt commit message.
 - Don't separate the new check in patch ("macsec: Add MACsec rx_handler change support")
   from the previous if/else if.
 - Drop"_found" from the parameter naming "rx_sc_found" and move the definition to
   the relevant block.
 - Remove "{}" since not needed around a single line.

 Updates since v5:
 - Consider promiscuous mode case.

 Updates since v6:
 - Use IS_ENABLED instead of checking for ifdef.
 - Don't add inline keywork in c files, let the compiler make its own decisions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Offloading device drivers will mark offloaded MACsec SKBs with the
corresponding SCI in the skb_metadata_dst so the macsec rx handler will
know to which interface to divert those skbs, in case of a marked skb
and a mismatch on the dst MAC address, divert the skb to the macsec
net_device where the macsec rx_handler will be called to consider cases
where relying solely on the dst MAC address is insufficient.

One such instance is when using MACsec with a VLAN as an inner
header, where the packet structure is ETHERNET | SECTAG | VLAN.
In such a scenario, the dst MAC address in the ethernet header
will correspond to the VLAN MAC address, resulting in a mismatch.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offloading MACsec when its configured over VLAN with current MACsec
TX steering rules will wrongly insert MACsec sec tag after inserting
the VLAN header leading to a ETHERNET | SECTAG | VLAN packet when
ETHERNET | VLAN | SECTAG is configured.

The above issue is due to adding the SECTAG by HW which is a later
stage compared to the VLAN header insertion stage.

Detect such a case and adjust TX steering rules to insert the
SECTAG in the correct place by using reformat_param_0 field in
the packet reformat to indicate the offset of SECTAG from end of
the MAC header to account for VLANs in granularity of 4Bytes.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MACsec device may have a VLAN device on top of it.
Detect MACsec state correctly under this condition,
and return the correct net device accordingly.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable MACsec offload feature over VLAN by adding NETIF_F_HW_MACSEC
to the device vlan_features.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for MACsec offload operations for VLAN driver
to allow offloading MACsec when VLAN's real device supports
Macsec offload by forwarding the offload request to it.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fix a plenty of flexible-array-nested warnings

Paolo noticed a compile warning in SCTP,

../net/sctp/stream_sched_fc.c: note: in included file (through ../include/net/sctp/sctp.h):
../include/net/sctp/structs.h:335:41: warning: array of flexible structures

But not only this, there are actually quite a lot of such warnings in
some SCTP structs. This patchset fixes most of warnings by deleting
these nested flexible array members.

After this patchset, there are still some warnings left:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  ./include/net/sctp/structs.h:1145:41: warning: nested flexible array
  ./include/uapi/linux/sctp.h:641:34: warning: nested flexible array
  ./include/uapi/linux/sctp.h:643:34: warning: nested flexible array
  ./include/uapi/linux/sctp.h:644:33: warning: nested flexible array
  ./include/uapi/linux/sctp.h:650:40: warning: nested flexible array
  ./include/uapi/linux/sctp.h:653:39: warning: nested flexible array

the 1st is caused by __data[] in struct ip_options, not in SCTP;
the others are in uapi, and we should not touch them.

Note that instead of completely deleting it, we just leave it as a
comment in the struct, signalling to the reader that we do expect
such variable parameters over there, as Marcelo suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array payload[] from the structure
sctp_datahdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/socket.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:230:29: warning: nested flexible array

This member is not even used anywhere.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array hmac[] from the structure
sctp_authhdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/auth.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:735:29: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array peer_init[] from the structure
sctp_cookie to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/sm_make_chunk.c: note: in included file (through include/net/sctp/sctp.h):
  ./include/net/sctp/structs.h:1588:28: warning: nested flexible array
  ./include/net/sctp/structs.h:343:28: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array variable[] from the structure
sctp_sackhdr and sctp_errhdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/sm_statefuns.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:451:28: warning: nested flexible array
  ./include/linux/sctp.h:393:29: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array skip[] from the structure
sctp_ifwdtsn/fwdtsn_hdr to avoid some sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/stream_interleave.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:611:32: warning: nested flexible array
  ./include/linux/sctp.h:628:33: warning: nested flexible array
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch deletes the flexible-array params[] from the structure
sctp_inithdr, sctp_addiphdr and sctp_reconf_chunk to avoid some
sparse warnings:

  # make C=2 CF="-Wflexible-array-nested" M=./net/sctp/
  net/sctp/input.c: note: in included file (through include/net/sctp/structs.h, include/net/sctp/sctp.h):
  ./include/linux/sctp.h:278:29: warning: nested flexible array
  ./include/linux/sctp.h:675:30: warning: nested flexible array

This warning is reported if a structure having a flexible array
member is included by other structures.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes Berg says:

====================
net: extend drop reasons

Here's v4 of the extended drop reasons, with fixes to kernel-doc
and checkpatch.
====================

Link: https://lore.kernel.org/r/20230419125254.20789-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It can be really hard to analyse or debug why packets are
going missing in mac80211, so add the needed infrastructure
to use use the new per-subsystem drop reasons.

We actually use two drop reason subsystems here because of
the different handling of frames that are dropped but still
go to monitor for old versions of hostapd, and those that
are just completely unusable (e.g. crypto failed.)

Annotate a few reasons here just to illustrate this, we'll
need to go through and annotate more of them later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend drop reasons to make them usable by subsystems
other than core by reserving the high 16 bits for a
new subsystem ID, of which 0 of course is used for the
existing reasons immediately.

To still be able to have string reasons, restructure
that code a bit to make the loopup under RCU, the only
user of this (right now) is drop_monitor.

Link: https://lore.kernel.org/netdev/00659771ed54353f92027702c5bbb84702da62ce.camel@sipsolutions.netSigned-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This will, after the next patch, hold only the core
drop reasons and minimal infrastructure. Fix a small
kernel-doc issue while at it, to avoid the move
triggering a checker.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ICMPv6 error packets are not sent to the anycast destinations and this
prevents things like traceroute from working. So create a setting similar
to ECHO when dealing with Anycast sources (icmpv6_echo_ignore_anycast).
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230419013238.2691167-1-maheshb@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
ethtool mm API consolidation

This series consolidates the behavior of the 2 drivers that implement
the ethtool MAC Merge layer by making NXP ENETC commit its preemptible
traffic classes to hardware only when MM TX is active (same as Ocelot).

Then, after resolving an issue with the ENETC driver, it restricts user
space from entering 2 states which don't make sense:

- pmac-enabled off tx-enabled on  verify-enabled *
- pmac-enabled *   tx-enabled off verify-enabled on

Then, it introduces a selftest (ethtool_mm.sh) which puts everything
together and tests all valid configurations known to me.

This is simultaneously the v2 of "[PATCH net-next 0/2] ethtool mm API
improvements":
https://lore.kernel.org/netdev/20230415173454.3970647-1-vladimir.oltean@nxp.com/
which had caused some problems to openlldp. Those were solved in the
meantime, see:
https://github.com/intel/openlldp/commit/11171b474f6f3cbccac5d608b7f26b32ff72c651

and of "[RFC PATCH net-next] selftests: forwarding: add a test for MAC
Merge layer":
https://lore.kernel.org/netdev/20230210221243.228932-1-vladimir.oltean@nxp.com/
====================

Link: https://lore.kernel.org/r/20230418111459.811553-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The MAC Merge layer (IEEE 802.3-2018 clause 99) does all the heavy
lifting for Frame Preemption (IEEE 802.1Q-2018 clause 6.7.2), a TSN
feature for minimizing latency.

Preemptible traffic is different on the wire from normal traffic in
incompatible ways. If we send a preemptible packet and the link partner
doesn't support preemption, it will drop it as an error frame and we
will never know. The MAC Merge layer has a control plane of its own,
which can be manipulated (using ethtool) in order to negotiate this
capability with the link partner (through LLDP).

Actually the TLV format for LLDP solves this problem only partly,
because both partners only advertise:
- if they support preemption (RX and TX)
- if they have enabled preemption (TX)
so we cannot tell the link partner what to do - we cannot force it to
enable reception of our preemptible packets.

That is fully solved by the verification feature, where the local device
generates some small probe frames which look like preemptible frames
with no useful content, and the link partner is obliged to respond to
them if it supports the standard. If the verification times out, we know
that preemption isn't active in our TX direction on the link.

Having clarified the definition, this selftest exercises the manual
(ethtool) configuration path of 2 link partners (with and without
verification), and the LLDP code path, using the openlldp project.

The test also verifies the TX activity of the MAC Merge layer by
sending traffic through a traffic class configured as preemptible
(using mqprio). There isn't a good way to make this really portable
(user space cannot find out how many traffic classes there are for
a device), but I chose num_tc 4 here, that should work reasonably well.
I also know that some devices (stmmac) only permit TXQ0 to be
preemptible, so this is why PREEMPTIBLE_PRIO was strategically chosen
as 0. Even if other hardware is more configurable, this test should
cover the baseline.

This is not really a "forwarding" selftest, but I put it near the other
"ethtool" selftests.

$ ./ethtool_mm.sh eno0 swp0
TEST: Manual configuration with verification: eno0 to swp0          [ OK ]
TEST: Manual configuration with verification: swp0 to eno0          [ OK ]
TEST: Manual configuration without verification: eno0 to swp0       [ OK ]
TEST: Manual configuration without verification: swp0 to eno0       [ OK ]
TEST: Manual configuration with failed verification: eno0 to swp0   [ OK ]
TEST: Manual configuration with failed verification: swp0 to eno0   [ OK ]
TEST: LLDP                                                          [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Counters for the MAC Merge layer and preemptible MAC have standardized
so far on using structured ethtool stats as opposed to the driver
specific names and meanings.

Benefit from that rare opportunity and introduce a helper to lib.sh for
querying standardized counters, in the hope that these will take off for
other uses as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>