In order to know the reason of link up failure, add supporting ethtool
extended link state. Driver reads the link status code from firmware if
in link down state and converts it to ethtool extended link state.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new file hns3_ethtool.h, and move struct type definitions from
hns3_ethtool.c to hns3_ethtool.h.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST means the input
external clock signal for SerDes is too weak or lost.

ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS means the received signal for
SerDes is too weak because analog loss of signal.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add documentation for two bad signal integrity substates:
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST
ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use a more user friendly netlink error message when a device can't be
enslaved because it has IFF_MASTER, by not referring directly to a
kernel internal flag.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: mcast: fixes for mcast querier state

These three fix querier state dumping. The first patch can be considered
a minor behaviour improvement, it avoids dumping querier state when mcast
snooping is disabled. The second patch was a report of sizeof(0) used
for nested netlink attribute size which should be just 0, and the third
patch accounts for IPv6 querier state size when allocating skb for
notifications.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to account for the IPv6 attributes when dumping querier state.

Fixes: 5e924fe6ccfd ("net: bridge: mcast: dump ipv6 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was a dumb error I made instead of writing nla_total_size(0)
for a nest attribute, I wrote nla_total_size(sizeof(0)).
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 606433fe3e11 ("net: bridge: mcast: dump ipv4 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A minor improvement to avoid dumping mcast ctx querier state if snooping
is disabled for that context (either bridge or vlan).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vijayakannan Ayyathurai says:

====================
net: stmmac: Add ethtool per-queue statistic

Adding generic ethtool per-queue statistic framework to display the
statistics for each rx/tx queue. In future, users can avail it to add
more per-queue specific counters. Number of rx/tx queues displayed is
depending on the available rx/tx queues in that particular MAC config
and this number is limited up to the MTL_MAX_{RX|TX}_QUEUES defined
in the driver.

Ethtool per-queue statistic display will look like below, when users
start adding more counters.

Example - 1:
 q0_tx_statA:
 q0_tx_statB:
 q0_tx_statC:
 |
 q0_tx_statX:
 .
 .
 .
 qMAX_tx_statA:
 qMAX_tx_statB:
 qMAX_tx_statC:
 |
 qMAX_tx_statX:

 q0_rx_statA:
 q0_rx_statB:
 q0_rx_statC:
 |
 q0_rx_statX:
 .
 .
 .
 qMAX_rx_statA:
 qMAX_rx_statB:
 qMAX_rx_statC:
 |
 qMAX_rx_statX:

Example - 2: Ping test using the tx queue 3.

$ tc qdisc add dev enp0s30f4 root mqprio num_tc 2 map 1 0 0 0 0 0 0 0
 0 0 0 0 0 0 0 0 queues 3@0 1@3 hw 0

Statistic before ping:
---------------------
$ ethtool -S enp0s30f4

[ snip ]
     q3_tx_pkt_n: 7916
     q3_tx_irq_n: 316
[ snip ]

$ cat /proc/interrupts

[ snip ]
 143:          0          0          0        316          0          0

         0          0  IR-PCI-MSI 499719-edge      enp0s30f4:tx-3
[ snip ]

$ ping -I enp0s30f4 192.168.1.10 -i 0.01 -c 100 > /dev/null

Statistic after ping:
---------------------
$ ethtool -S enp0s30f4

[ snip ]
     q3_tx_pkt_n: 8016
     q3_tx_irq_n: 320
[ snip ]

$ cat /proc/interrupts

[ snip ]
143:          0          0          0        320          0          0

         0          0  IR-PCI-MSI 499719-edge      enp0s30f4:tx-3
[ snip ]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding ethtool per-queue statistics support to show number of interrupts
generated at DMA tx and DMA rx. All the counters are incremented at
dwmac4_dma_interrupt function.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding generic ethtool per-queue statistic framework to display the
statistics for each rx/tx queue. In future, users can avail it to add
more per-queue specific counters. Number of rx/tx queues displayed is
depending on the available rx/tx queues in that particular MAC config
and this number is limited up to the MTL_MAX_{RX|TX}_QUEUES defined
in the driver.

Ethtool per-queue statistic display will look like below, when users
start adding more counters.

Example:
 q0_tx_statA:
 q0_tx_statB:
 q0_tx_statC:
 |
 q0_tx_statX:
 .
 .
 .
 qMAX_tx_statA:
 qMAX_tx_statB:
 qMAX_tx_statC:
 |
 qMAX_tx_statX:

 q0_rx_statA:
 q0_rx_statB:
 q0_rx_statC:
 |
 q0_rx_statX:
 .
 .
 .
 qMAX_rx_statA:
 qMAX_rx_statB:
 qMAX_rx_statC:
 |
 qMAX_rx_statX:

In addition, this patch has the support on displaying the number of
packets received and transmitted per queue.
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA channel status "Transmit buffer unavailable(TBU)" bit is not
considered as a successful dma tx. Hence, it should not affect
all the irq count statistic.

Fixes: 1103d3a5 ("net: stmmac: dwmac4: Also use TBU interrupt to clean TX path")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sja1105 driver's initialization and teardown sequence is a chaotic
mess that has gathered a lot of cruft over time. It works because there
is no strict dependency between the functions, but it could be improved.

The basic principle that teardown should be the exact reverse of setup
is obviously not held. We have initialization steps (sja1105_tas_setup,
sja1105_flower_setup) in the probe method that are torn down in the DSA
.teardown method instead of driver unbind time.

We also have code after the dsa_register_switch() call, which implicitly
means after the .setup() method has finished, which is pretty unusual.

Also, sja1105_teardown() has calls set up in a different order than the
error path of sja1105_setup(): see the reversed ordering between
sja1105_ptp_clock_unregister and sja1105_mdiobus_unregister.

Also, sja1105_static_config_load() is called towards the end of
sja1105_setup(), but sja1105_static_config_free() is also towards the
end of the error path and teardown path. The static_config_load() call
should be earlier.

Also, making and breaking the connections between struct sja1105_port
and struct dsa_port could be refactored into dedicated functions, makes
the code easier to follow.

We move some code from the DSA .setup() method into the probe method,
like the device tree parsing, and we move some code from the probe
method into the DSA .setup() method to be symmetric with its placement
in the DSA .teardown() method, which is nice because the unbind function
has a single call to dsa_unregister_switch(). Example of the latter type
of code movement are the connections between ports mentioned above, they
are now in the .setup() method.

Finally, due to fact that the kthread_init_worker() call is no longer
in sja1105_probe() - located towards the bottom of the file - but in
sja1105_setup() - located much higher - there is an inverse ordering
with the worker function declaration, sja1105_port_deferred_xmit. To
avoid that, the entire sja1105_setup() and sja1105_teardown() functions
are moved towards the bottom of the file.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the function to reflect what it's doing. Also add a description
of the register values as kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Convert ocelot to phylink

The ocelot switchdev and felix dsa drivers are interesting because they
target the same class of hardware switches but used in different modes.

Colin has an interesting use case where he wants to use a hardware
switch supported by the ocelot switchdev driver with the felix dsa
driver.

So far, the existing hardware revisions were similar between the ocelot
and felix drivers, but not completely identical. With identical hardware,
it is absurd that the felix driver uses phylink while the ocelot driver
uses phylib - this should not be one of the differences between the
switchdev and dsa driver, and we could eliminate it.

Colin will need the common phylink support in ocelot and felix when
adding a phylink_pcs driver for the PCS1G block inside VSC7514, which
will make the felix driver work with either the NXP or the Microchip PCS.

As usual, Alex, Horatiu, sorry for bugging you, but it would be
appreciated if you could give this a quick run on actual VSC7514
hardware (which I don't have) to make sure I'm not introducing any
breakage.
====================

Fixes: 0f06a678 ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: David S. Miller <davem@davemloft.net>

The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.

This is a large patch and hard to break up, but it does the following:

The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.

The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
  write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
  changes actually break the link and must be avoided.

The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
  instantiations and placed in ocelot_net.c which is built only for the
  ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
  switchdev driver and the felix DSA driver (they are put in the common
  lib).

One by one, the registers written by ocelot_adjust_link are:

DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
                   register since its out-of-reset value was fine and
                   did not need changing. The write is moved to the
                   common ocelot_phylink_mac_link_up and on felix it is
                   guarded by a quirk bit that makes the written value
                   identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
                  touched this. felix_phylink_mac_link_{up,down} also
                  do. We go with what felix does and put it in
                  ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
                write this, but to different values. Move to the common
                ocelot_phylink_mac_link_up and make sure via the quirk
                that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
                  did not. Runtime invariant, speed does not matter since
                  PFC is disabled via the RX_PFC_ENA bits which are cleared.
                  Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
                                 felix_phylink_mac_link_{up,down} wrote
                                 this. Ocelot also wrote this register
                                 from ocelot_port_disable. Keep what
                                 felix did, move in ocelot_phylink_mac_link_{up,down}
                                 and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
                 ocelot always enabled RX and TX flow control, felix
                 listened to phylink (for the most part, at least - see
                 the 2500base-X comment).

The registers which only felix_phylink_mac_link_up wrote are:

SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
                          worked on ocelot. Not it should, since the
                          code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
                    should be the one touching them, deleted.

Other changes:

- The old phylib registration code was in mscc_ocelot_init_ports. It is
  hard to work with 2 levels of indentation already in, and with hard to
  follow teardown logic. The new phylink registration code was moved
  inside ocelot_probe_port(), right between alloc_etherdev() and
  register_netdev(). It could not be done before (=> outside of)
  ocelot_probe_port() because ocelot_probe_port() allocates the struct
  ocelot_port which we then use to assign ocelot_port->phy_mode to. It
  is more preferable to me to have all PHY handling logic inside the
  same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
  in ocelot_port_open to set the SERDES protocol to Ethernet. This is
  logically a runtime invariant and can be done just once, when the port
  registers with phylink. We therefore don't even need to keep the
  serdes reference inside struct ocelot_port_private, or to use the devm
  variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
  the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
  don't define one for the internal PHY ports. So we patch
  PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:

	switch (priv->phy_mode) {
	case PHY_INTERFACE_MODE_NA:
	        continue;

  which made the code skip the serdes initialization for the internal
  PHY ports. Frankly that is not all that obvious, so now we explicitly
  initialize the serdes under an "if" condition and not rely on code
  jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
  ports. Since that is in fact the default value for the register field
  DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
  the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
  of reset, which does match the comment. I don't even want to know why
  this code is placed there, but if there is indeed an issue that all
  ports that share a QSGMII lane must all be up, then this logic is
  already buggy, since mscc_ocelot_init_ports iterates using
  for_each_available_child_of_node, so nobody prevents the user from
  putting a 'status = "disabled";' for some QSGMII ports which would
  break the driver's assumption.
  In any case, in the eventuality that I'm right, we would have yet
  another issue if ocelot_phylink_mac_link_down would reset those ports
  and that would be forbidden, so since the ocelot_adjust_link logic did
  not do that (maybe for a reason), add another quirk to preserve the
  old logic.

The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.

Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:

- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
  which are written with their hardware default values, also runtime
  invariants. So it makes no sense to write these during every .ndo_open.

- PORTID_VAL: this field has an out-of-reset value of zero for all ports
  and must be initialized by software. Additionally, the
  ocelot_setup_logical_port_ids() code path sets up different logical
  port IDs for the ports in a hardware LAG, and we absolutely don't want
  .ndo_open to interfere there and reset those values.

So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.

ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.

So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the obsolete and ambiguos macro in_irq() with new
macro in_hardirq().
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During the development of the blamed patch, the "bool broadcast"
argument of dsa_port_tag_8021q_vlan_{add,del} was originally called
"bool local", and the meaning was the exact opposite.

Due to a rookie mistake where the patch was modified at the last minute
without retesting, the instances of dsa_port_tag_8021q_vlan_{add,del}
are called with the wrong values. During setup and teardown, cross-chip
notifiers should not be broadcast to all DSA trees, while during
bridging, they should.

Fixes: 724395f4 ("net: dsa: tag_8021q: don't broadcast during setup/teardown")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kconfig warning on arch/s390/:

WARNING: unmet direct dependencies detected for SERIAL_8250
  Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && !S390 [=y]
  Selected by [m]:
  - PTP_1588_CLOCK_OCP [=m] && PTP_1588_CLOCK [=m] && HAS_IOMEM [=y] && PCI [=y] && SPI [=y] && I2C [=m] && MTD [=m]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

edumazet@google.com pointed out that queue_oob
does not check socket state after acquiring
the lock. He also pointed to an incorrect usage
of kfree_skb and an unnecessary setting of skb
length. This patch addresses those issue.
Signed-off-by: Rao Shoaib <Rao.Shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Wake-on-PHY feature support by enabling the Link Up Event.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

SGMII/2500BaseX supports Pause frame as defined in the IEEE802.3x
Flow Control standardization.

Add this as a supported feature under the xpcs_sgmii_features struct.

Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

samples: pktgen: enhance the usability of pktgen samples

This patchset improves the usability of pktgen samples by adding an option for
propagating the environment variable of normal user to sudo. And also adds the
missing IPv6 option to pktgen scripts.

Currently, all pktgen samples are able to use the environment variable instead
of optional parameters. However, it doesn't work appropriately when running
samples as normal user.

This is results of running sample as root and user:

    // running as root
    # DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
    Running... ctrl^C to stop

    // running as normal user
    $ DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
    [...]
    ERROR: Please specify output device

The reason why passing the environment varaible doesn't work properly when
running samples as normal user is that the environment variable of normal user
doesn't propagate to sudo (root_check_run_with_sudo)). So the first commit
solves this issue by using "-E" (--preserve-env) option of "sudo", which passes
normal user's existing environment variables.

Also, "sample04" and "sample05" are not working properly when running with IPv6
option parameter("-6"). Because the commit 0f06a678 ("samples: Add an IPv6
"-6" option to the pktgen scripts") has omitted the addition of this option at
these samples. So the second commit adds missing IPv6 option to pktgen scripts.

====================

Fixes: 0f06a678 ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, "sample04" and "sample05" are not working properly when
running with an IPv6 option("-6"). The commit 0f06a678 ("samples:
Add an IPv6 "-6" option to the pktgen scripts") has omitted the addition
of this option at "sample04" and "sample05".

In order to support IPv6 option, this commit adds logic related to IPv6
option.

Fixes: 0f06a678 ("samples: Add an IPv6 "-6" option to the pktgen scripts")
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All pktgen samples can use the environment variable instead of option
parameters(eg. $DEV is able to use instead of '-i' option).

This is results of running sample as root and user:

    // running as root
    # DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
    Running... ctrl^C to stop

    // running as normal user
    $ DEV=eth0 DEST_IP=10.1.0.1 DST_MAC=00:11:22:33:44:55 ./pktgen_sample01_simple.sh -v -n 1
    [...]
    ERROR: Please specify output device

This results show the sample doesn't work properly when the sample runs
as normal user. Because the sample is restarted by the function
(root_check_run_with_sudo) to run with sudo. In this process, the
environment variable of normal user doesn't propagate to sudo.

It can be solved by using "-E"(--preserve-env) option of "sudo", which
preserve normal user's existing environment variables. So this commit
adds "-E" option in the function (root_check_run_with_sudo).
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luo Jie says:

====================
net: mdio: Add IPQ MDIO reset related function

This patch series add the MDIO reset features, which includes
configuring MDIO clock source frequency and indicating CMN_PLL that
ethernet LDO has been ready, this ethernet LDO is dedicated in the
IPQ5018 platform.

Specify more chipset IPQ40xx, IPQ807x, IPQ60xx and IPQ50xx supported by
this MDIO driver.

Changes in v3:
	* simplify the function ipq_mdio_reset.

Changes in v2:
	* Addressed review comments (Andrew Lunn).
	* Remove the IS_ERR().
	* make binding patch part of series.
	* document the property 'reg' and 'clock'.

Changes in v1:
	* make MDIO_IPQ4019 unchanged for backwards compatibility.
	* remove the PHY reset functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new added properties resource "reg" is for configuring
ethernet LDO in the IPQ5018 chipset, the property "clocks"
is for configuring the MDIO clock source frequency.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPQ MDIO driver currently supports the chipset IPQ40xx, IPQ807x,
IPQ60xx and IPQ50xx.

Add the compatible 'qcom,ipq5018-mdio' because of ethernet LDO dedicated
to the IPQ5018 platform.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. configure the MDIO clock source frequency.
2. the LDO resource is needed to configure the ethernet LDO available
for CMN_PLL.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit <47595e32> ("<MAINTAINERS: Mark some staging directories>")
indicated the ipx network layer as obsolete in Jan 2018,
updated in the MAINTAINERS file.

now, after being exposed for 3 years to refactoring, so to
remove the ipx network layer info from MAINTAINERS.
additionally, there is no module that depends on ipx.h
except a broken staging driver(r8188eu)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit <47595e32> ("<MAINTAINERS: Mark some staging directories>")
indicated the ipx network layer as obsolete in Jan 2018,
updated in the MAINTAINERS file

now, after being exposed for 3 years to refactoring, so to
delete uapi/linux/ipx.h and net/ipx.h header files for good.
additionally, there is no module that depends on ipx.h except
a broken staging driver(r8188eu)
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: last things before PM conversion

This series contains a few remaining changes needed before fully
switching over to using runtime power management rather than the
previous "IPA clock" mechanism.

The first patch moves the calls to enable and disable the IPA
interrupt as a system wakeup interrupt into "ipa_clock.c" with the
rest of the power-related code.

The second adds a flag to make it possible to distinguish runtime
suspend from system suspend.

The third and fourth patches arrange for the ->start_xmit path to
resume hardware if necessary, to ensure it is powered.  If power is
not active, the TX queue is stopped, and arrangements are made for
the queue to be restarted once hardware power is active again.

The fifth patch keeps the TX queue active during suspend.  This
isn't necessary for system suspend but it's important for runtime
suspend.

And the last patch makes it so we don't hold the hardware active
while the modem network device is open.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently a clock reference is taken whenever the ->ndo_open
callback for the modem netdev is called.  That reference is dropped
when the device is closed, in ipa_stop().

We no longer need this, because ipa_start_xmit() now handles the
situation where the hardware power state is not active.

Drop the clock reference in ipa_open() when we're done, and take a
new reference in ipa_stop() before we begin closing the interface.

Finally (and unrelated, but trivial), change the return type of
ipa_start_xmit() to be netdev_tx_t instead of int.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we stop the modem netdev transmit queue when suspending
the hardware.  For system suspend this ensured we'd never attempt
to transmit while attempting to suspend the modem endpoints.

For runtime suspend, the IPA hardware might get suspended while the
system is operating.  In that case we want an attempt to transmit a
packet to cause the hardware to resume if necessary.  But if we
disable the queue this cannot happen.

So stop disabling the queue on suspend.  In case we end up disabling
it in ipa_start_xmit() (see the previous commit), we still arrange
to start the TX queue on resume.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to ensure the hardware is powered when we transmit a packet.
But if it's not, we can't block to wait for it.  So asynchronously
request power in ipa_start_xmit(), and only proceed if the return
value indicates the power state is active.

If the hardware is not active, a runtime resume request will have
been initiated.  In that case, stop the network stack from further
transmit attempts until the resume completes.  Return NETDEV_TX_BUSY,
to retry sending the packet once the queue is restarted.

If the power request returns an error (other than -EINPROGRESS,
which just means a resume requested elsewhere isn't complete), just
drop the packet.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a new work structure in the modem private data, and use it to
re-enable the modem network device transmit queue when resuming.

This is needed by the next patch, which stops the TX queue if IPA
power isn't active when a transmit request arrives.  Packets will
start arriving the instant the TX queue is enabled, but resuming
isn't complete until ipa_modem_resume() returns.  This way we're
sure to be resumed before transmits are allowed again.

Cancel it before calling ipa_stop() in ipa_modem_stop() to ensure
the transmit queue restart completes before it gets stopped there.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new flag that is set when the hardware is suspended due to a
system suspend operation, distingishing it from runtime suspend.
Use it in the SUSPEND IPA interrupt handler to determine whether to
trigger a system resume because of the event.  Define new suspend
and resume power management callback functions to set and clear the
new flag, respectively.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the call to enable the IPA interrupt as a wakeup interrupt into
ipa_power_setup(), disable it in ipa_power_teardown().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>