- 28 Jun, 2013 21 commits
-
-
Sylwester Nawrocki authored
Add compatible property for the Exynos5250 and enable the frame start and frame end interrupts. These interrupts are needed for the Exynos5 FIMC-IS firmware. The driver enables those interrupt only where available, depending on the 'compatible' property. This can be optimized further, by exposing some API at the subdev driver, so the host driver can enable extra interrupts only for the image processing chains involving FIMC-IS. Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
This patch adds support for the Exynos5250 SoC variant of the FIMC-LITE IP. A 'compatible' string is added for Exynos5250 compatible devices and the capture DMA handling is reworked to use the FLITE_REG_CIFCNTSEQ register, masking output DMA buffer address slots. The frame interrupt is enabled so there are now 2 interrupts per frame. This likely can be optimized in future by using any status registers that allow to figure out what the last and the currently written frame buffer is. It would also be more reliable in cases where there are high interrupt service latencies. Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com> Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
The FIMC-LITE IP block is available only on platforms instantiated from device tree. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
This patch removes manual setting of subdev name in the probe, ideally subdev names must be unique. Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
This patch removes manual setting of subdev name in the probe, ideally subdev names must be unique. Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
The m2m-deinterlace, mem2mem_testdev and mx2_emmaprp drivers didn't set the v4l2_dev pointer in struct video_device, even though a v4l2_device was registered correctly. These days this v4l2_dev pointer must be set correctly, so this patch adds that for these three drivers. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
This struct is now required for all video device nodes, but it was missing in this driver. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lars-Peter Clausen authored
client->driver->id_table will always point to the first entry in the device id table. So all devices will use the same init sequence. Use the id table entry that gets passed to the driver's probe() function to get the right init sequence. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Emil Goode authored
Adding a __user annotation fixes the following sparse warnings. drivers/media/pci/saa7134/saa7134-video.c:1578:45: warning: incorrect type in initializer (different address spaces) drivers/media/pci/saa7134/saa7134-video.c:1578:45: expected struct v4l2_clip *clips drivers/media/pci/saa7134/saa7134-video.c:1578:45: got struct v4l2_clip [noderef] <asn:1>*clips drivers/media/pci/saa7134/saa7134-video.c:1589:26: warning: incorrect type in assignment (different address spaces) drivers/media/pci/saa7134/saa7134-video.c:1589:26: expected struct v4l2_clip [noderef] <asn:1>*clips drivers/media/pci/saa7134/saa7134-video.c:1589:26: got struct v4l2_clip *clips Signed-off-by: Emil Goode <emilgoode@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
build/media_build/v4l/saa7164-core.c: In function 'saa7164_initdev': build/media_build/v4l/saa7164-core.c:1192:6: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized] int err, i; ^ Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
The comment for the FM_RX class was copied from the DV class unchanged. Fixed. Also made the FM_TX comment consistent with the others. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
media-git/drivers/media/platform/omap/omap_vout.c: In function ‘omapvid_init’: media-git/drivers/media/platform/omap/omap_vout.c:382:17: warning: ‘mode’ may be used uninitialized in this function [-Wmaybe-uninitialized] vout->dss_mode = video_mode_to_dss_mode(vout); ^ media-git/drivers/media/platform/omap/omap_vout.c:332:23: note: ‘mode’ was declared here enum omap_color_mode mode; ^ Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Prabhakar Lad <prabhakar.lad@ti.com> Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
media-git/drivers/media/platform/blackfin/bfin_capture.c: In function ‘bcap_probe’: media-git/drivers/media/platform/blackfin/bfin_capture.c:1007:16: warning: ignoring return value of ‘vb2_queue_init’, declared with attribute warn_unused_result [-Wunused-result] vb2_queue_init(q); ^ Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
build/media_build/v4l/ml86v7667.c: In function 'ml86v7667_s_ctrl': build/media_build/v4l/ml86v7667.c:120:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable] int ret = 0; ^ Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Vladimir Barinov <source@cogentembedded.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
The scaling / cropping library, that has been extracted from the CEU driver still contained a couple of references to the original hardware. Clean them up. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
The sh_mobile_ceu_camera driver implements a generic algorithm for setting up an optimal client and host scaling and cropping configuration. This patch makes those functions available for all drivers. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Several functions in the sh_mobile_ceu_camera driver implement generic algorithms and can be re-used by other V4L2 camera host drivers too. These functions attempt to optimise scaling and cropping functions of the subdevice, e.g. a camera sensor. This patch makes those functions generic for future re-use by other camera host drivers. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Add documentation for the V4L2 clock and V4L2 asynchronous probing APIs to v4l2-framework.txt. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
In scan_async_group() if the size parameter is negative, the sasd pointer will be used uninitialised: drivers/media/platform/soc_camera/soc_camera.c: In function "soc_camera_host_register": drivers/media/platform/soc_camera/soc_camera.c:1514:55: warning: "sasd" may be used uninitialized in this function [-Wmaybe-uninitialized] sasd->asd.match.i2c.adapter_id, sasd->asd.match.i2c.address); ^ drivers/media/platform/soc_camera/soc_camera.c:1464:34: note: "sasd" was declared here struct soc_camera_async_subdev *sasd; Fix this by making "size" and the array, from which it is assigned unsigned. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
i2c_verify_client() is only available, if I2C is enabled. Fix v4l2-async.c compilation if I2C is disabled. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
The sh_vou driver needs CONFIG_I2C or CONFIG_I2C_MODULE to build, add the respective dependency. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 25 Jun, 2013 2 commits
-
-
Mauro Carvalho Chehab authored
* v4l_for_linus: [media] Fix build when drivers are builtin and frontend modules [media] s5p makefiles: don't override other selections on obj-[ym] [media] exynos4-is: Fix FIMC-IS clocks initialization [media] rtl28xxu: fix buffer overflow when probing Rafael Micro r820t tuner Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
The uvcvideo driver lost its dependency on VIDEO_V4L2 during the big media directory reorganization. Add it back. Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 21 Jun, 2013 17 commits
-
-
Guennadi Liakhovetski authored
Both synchronous and asynchronous imx074 subdevice probing is supported by this patch. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Use the v4l2-async API to support asynchronous subdevice probing, including the CSI2 subdevice. Synchronous probing is still supported too. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Add support for asynchronous subdevice probing, using the v4l2-async API. The legacy synchronous mode is still supported too, which allows to gradually update drivers and platforms. The selected approach adds a notifier for each struct soc_camera_device instance, i.e. for each video device node, even when there are multiple such instances registered with a single soc-camera host simultaneously. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Instead of centrally enabling and disabling subdevice master clocks in soc-camera core, let subdevice drivers do that themselves, using the V4L2 clock API and soc-camera convenience wrappers. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Currently bridge device drivers register devices for all subdevices synchronously, typically, during their probing. E.g. if an I2C CMOS sensor is attached to a video bridge device, the bridge driver will create an I2C device and wait for the respective I2C driver to probe. This makes linking of devices straight forward, but this approach cannot be used with intrinsically asynchronous and unordered device registration systems like the Flattened Device Tree. To support such systems this patch adds an asynchronous subdevice registration framework to V4L2. To use it respective (e.g. I2C) subdevice drivers must register themselves with the framework. A bridge driver on the other hand must register notification callbacks, that will be called upon various related events. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
It is often useful to have simple means to get from a subdevice to the underlying physical device. This patch adds such a pointer to struct v4l2_subdev and sets it accordingly in the I2C and SPI cases. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Typical video devices like camera sensors require an external clock source. Many such devices cannot even access their hardware registers without a running clock. These clock sources should be controlled by their consumers. This should be performed, using the generic clock framework. Unfortunately so far only very few systems have been ported to that framework. This patch adds a set of temporary helpers, mimicking the generic clock API, to V4L2. Platforms, adopting the clock API, should switch to using it. Eventually this temporary API should be removed. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Some CEU implementations have non-standard (larger) maximum supported width and height values. Add two OF properties to specify them. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Add an OF hook to sh_mobile_ceu_camera.c, no properties so far. Booting with DT also requires platform data to be optional. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
During client probing we only have to turn on the host's clock, no need to actually attach the client to the host. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
All existing soc-camera host drivers use .clock_start() and .clock_stop() callbacks to activate and deactivate their camera interfaces, whereas .add() and .remove() callbacks are usually dummy. Make the former two compulsory and the latter two optional. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the sh-mobile-ceu-camera driver activates and, respectively, deactivates its camera interface and, if necessary, the CSI2 controller. Only handling of the CSI2 interface is client-specific and is only needed, when a data-exchange with the client is taking place. Move the rest to .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the mx1-camera driver only activates and deactivates its camera interface respectively, which doesn't include any client-specific actions. Move this functionality into .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the mx2-camera driver only activates and deactivates its camera interface respectively, which doesn't include any client-specific actions. Move this functionality into .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the mx3-camera driver only activates and deactivates its camera interface respectively, which doesn't include any client-specific actions. Move this functionality into .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the atmel-isi camera host driver only activates and deactivates its camera interface respectively, which doesn't include any client-specific actions. Move this functionality into .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
When adding and removing a client, the omap1-camera driver only activates and deactivates its camera interface respectively, which doesn't include any client-specific actions. Move this functionality into .clock_start() and .clock_stop() callbacks. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-