Remove the last address definitions relative to the IPSBAR peripheral region
for the ColdFire 527x family. This involved cleaning up some magic numbers
used in the code part, and making them proper register definitions in the 527x
specific header.

This is part of the process of cleaning up the ColdFire register definitions
to make them consistently use absolute addresses for the primary registers.
This will reduce the occasional bugs caused by inconsistent definition of
the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

There is a bunch of old unused and ugly register definitions in the ColdFire
5282 header. Remove them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

The registers used to configure and set the multifunction pins on the 5272
ColdFire are defined as absolute addresses. So the use of them does not need
to be offset relative to the peripheral region address.

Fix two cases of incorrect usage of these addresses. Both affect UART
initialization, one in the common UART pin setup code, the other in the
NETtel board specific UART signal handling.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make the ColdFire 5249 MBAR peripheral register definitions absolute
addresses, instead of offsets into the region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make the remaining definitions of the 5272 ColdFire registers absolute
addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire MPARK and IRQ Assignment registers
absolute addresses. Currently some are relative to the MBAR peripheral
region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Chip Select registers absolute addresses.
Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Interrupt Source registers absolute
addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Pin Assignment registers absolute
addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Software watchdog registers absolute
addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Reset and System registers absolute
addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the abolsute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Make all definitions of the ColdFire Interrupt Mask and Pending registers
absolute addresses. Currently some are relative to the MBAR peripheral region.

The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.

This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Let the compiler choose which register to use in the cache flushing
asm statements, instead of imposing %d0.

Additionally, fix two typo's.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

DRAGEN2 should obviously be CONFIG_DRAGEN2, but the screen.h entry it
triggers only references files that are nowhere to be found in the
current tree. Besides, nothing uses screen.h. So just drop all that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

Pull kbuild fixes from Michal Marek:
 "There are two more kbuild fixes for 3.6.

  One fixes a race between x86's archscripts target and the rule
  (re)building scripts/basic/fixdep.  The second is a fix for the
  previous attempt at fixing make firmware_install with make 3.82.
  This new solution should work with any version of GNU make"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  x86/kbuild: archscripts depends on scripts_basic
  firmware: fix directory creation rule matching with make 3.80

Pull hwmon subsystem fixes from Jean Delvare.

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (fam15h_power) Tweak runavg_range on resume
  hwmon: (coretemp) Use get_online_cpus to avoid races involving CPU hotplug
  hwmon: (via-cputemp) Use get_online_cpus to avoid races involving CPU hotplug

Pull SCSI fixes from James Bottomley:
 "This is a set of four essential fixes: two oops related (bnx2i,
  virtio-scsi), one data corruption related (hpsa) and one failure to
  boot due to interrupt routing issues (mpt2ss).

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] hpsa: fix handling of protocol error
  [SCSI] mpt2sas: Fix for issue - Unable to boot from the drive connected to HBA
  [SCSI] bnx2i: Fixed NULL ptr deference for 1G bnx2 Linux iSCSI offload
  [SCSI] scsi: virtio-scsi: Fix address translation failure of HighMem pages used by sg list

Fix potential NULL pointer dereference in edac_unregister_sysfs() on
system boot introduced in 3.6-rc1.

Since commit 7a623c03 ("edac: rewrite the sysfs code to use struct
device") edac_mc_alloc() no longer initializes embedded kobjects in
struct mem_ctl_info.  Therefore edac_mc_free() can no longer simply
decrement a kobject reference count to free the allocated memory unless
the memory controller driver module had also called edac_mc_add_mc().

Now edac_mc_free() will check if the newly embedded struct device has
been registered with sysfs before using either the standard device
release functions or freeing the data structures itself with logic
pulled out of the error path of edac_mc_alloc().

The BUG this patch resolves for me:

  BUG: unable to handle kernel NULL pointer dereference at   (null)
  EIP is at __wake_up_common+0x1a/0x6a
  Process modprobe (pid: 933, ti=f3dc6000 task=f3db9520 task.ti=f3dc6000)
  Call Trace:
    complete_all+0x3f/0x50
    device_pm_remove+0x23/0xa2
    device_del+0x34/0x142
    edac_unregister_sysfs+0x3b/0x5c [edac_core]
    edac_mc_free+0x29/0x2f [edac_core]
    e7xxx_probe1+0x268/0x311 [e7xxx_edac]
    e7xxx_init_one+0x56/0x61 [e7xxx_edac]
    local_pci_probe+0x13/0x15
  ...

Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coccinelle warns about:

+ drivers/edac/edac_mc.c:429:9-23: ERROR: reference preceded by free on line 429

   421         if (mci->csrows) {
 > 422                 for (chn = 0; chn < tot_channels; chn++) {
   423                         csr = mci->csrows[chn];
   424                         if (csr) {
 > 425                                 for (chn = 0; chn < tot_channels; chn++)
   426                                          kfree(csr->channels[chn]);
   427                                  kfree(csr);
   428                          }
 > 429                          kfree(mci->csrows[i]);
   430                  }
   431                  kfree(mci->csrows);
   432          }

and that code block seem to mess things up in several ways (double free, memory
leak, out-of-bound reads etc.):

L422: The iterator "chn" and bound "tot_channels" are totally wrong. Should be
      "row" and "tot_csrows" respectively. Which means either memory leak, or
      out-of-bound reads (which if does not trigger an immediate page fault
      error, will further lead to kfree() on random addresses).

L425: The inner loop is reusing the same iterator "chn" as the outer loop,
      which could lead to premature end of the outer loop, and hence memory leak.

L429: The array index 'i' in mci->csrows[i] is a temporary value used in
      previous loops, and won't change at all in the current loop. Which
      means either out-of-bound read and possibly kfree(random number), or the
      same mci->csrows[i] get freed once and again, and possibly double free
      for the kfree(csr) in L427.

L426/L427: a kfree(csr->channels) is needed in between to avoid leaking the memory.

The buggy code was introduced by commit de3910eb ("edac: change the mem
allocation scheme to make Documentation/kobject.txt happy") in the 3.6-rc1
merge window. Fix it by freeing up resources in this order:

  free csrows[i]->channels[j]
  free csrows[i]->channels
  free csrows[i]
  free csrows

CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The quirk introduced with commit
00250ec9 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+

coretemp_init loops with for_each_online_cpu, adding platform_devices
and sysfs interfaces, then calls register_hotcpu_notifier.  There is a
race if a CPU is offlined or onlined after the loop, but before
register_hotcpu_notifier.  The race might result in the absence of a
platform_device+sysfs interface for an online CPU, or the presence of
a platform_device+sysfs interface for an offline CPU.  A similar race
occurs during coretemp_exit, after the module calls
unregister_hotcpu_notifier, but before it unregisters all devices, a
CPU might offline and a device for an offline CPU will exist for a
short while.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

via_cputemp_init loops with for_each_online_cpu, adding
platform_devices, then calls register_hotcpu_notifier.  If a CPU is
offlined between the loop and register_hotcpu_notifier, then later
onlined, via_cputemp_device_add will attempt to add platform devices
with the same ID.  A similar race occurs during via_cputemp_exit,
after the module calls unregister_hotcpu_notifier, a CPU might offline
and a device will exist for a CPU that is offline.

This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.

Build tested.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Pull MIPS fixes from Ralf Baechle:
 "Random fixes across arch/mips, essentially.

  One fix for an issue in get_user_pages_fast() which previously was
  discovered on x86, a miscalculation in the support for the MIPS MT
  hardware multithreading support, the RTC support for the Malta and a
  fix for a spurious interrupt issue that seems to bite only very
  special Malta configurations."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Malta: Don't crash on spurious interrupt.
  MIPS: Malta: Remove RTC Data Mode bootstrap breakage
  MIPS: mm: Add compound tail page _mapcount when mapped
  MIPS: CMP/SMTC: Fix tc_id calculation

Pull ARM and clkdev fixes from Russell King:
 "Two patches for clkdev which resolve the long standing issue that the
  devm_* versions were dependent on clkdev, which they shouldn't have
  been.  Instead, they're dependent on HAVE_CLK instead, which implies
  that you're providing clk_get() and clk_put().

  A small fix to the ARM decompressor to ensure that the page tables are
  properly interpreted by the CPU, and reserve syscall 378 for kcmp (the
  checksyscalls.sh script is unfortunately currently broken so arch
  maintainers aren't getting notified of new syscalls...)

  Lastly, a larger fix for an issue between the common clk subsystem and
  smp_twd which causes warnings to be spat out."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: reserve syscall 378 for kcmp
  ARM: 7535/1: Reprogram smp_twd based on new common clk framework notifiers
  ARM: 7537/1: clk: Fix release in devm_clk_put()
  ARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores
  ARM: 7534/1: clk: Make the managed clk functions generically available

Pull HID fixes from Jiri Kosina:
 "The most important fix is Logitech Unifying receiver regression in
  device enumeration fix from Nestor Lopez Casado.  In addition to that,
  there is a small memory leak fix for Thinkpad keyboard driver from
  Axel Lin."

* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Fix logitech-dj: missing Unifying device issue
  HID: lenovo-tpkbd: Fix memory leak in tpkbd_remove_tp()

Pull cifs fix from Steve French.

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix return value in cifsConvertToUTF16

This patch fixes an issue introduced after commit 4ea54542
("HID: Fix race condition between driver core and ll-driver").

After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.

This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.

This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.

Based on a patch originally written by Benjamin Tissoires.

Cc: stable@vger.kernel.org   # v3.2+
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

We need to kfree names for led_mute and led_micmute in tpkbd_remove_tp().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Bernhard Seibold <mail@bernhard-seibold.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull networking updates from David Miller:
 "More bug fixes, nothing gets past these guys"

 1) More kernel info leaks found by Mathias Krause, this time in the
    IPSEC configuration layers.

 2) When IPSEC policies change, we do not properly make sure that cached
    routes (which could now be stale) throughout the system will be
    revalidated.  Fix this by generalizing the generation count
    invalidation scheme used by ipv4.  From Nicolas Dichtel.

 3) When repairing TCP sockets, we need to allow to restore not just the
    send window scale, but the receive one too.  Extend the existing
    interface to achieve this in a backwards compatible way.  From
    Andrey Vagin.

 4) A fix for FCOE scatter gather feature validation erroneously caused
    scatter gather to be disabled for things like AOE too.  From Ed L
    Cashin.

 5) Several cases of mishandling of error pointers, from Mathias Krause,
    Wei Yongjun, and Devendra Naga.

 6) Fix gianfar build, from Richard Cochran.

 7) CAP_NET_* failures should return -EPERM not -EACCES, from Zhao
    Hongjiang.

 8) Hardware reset fix in janz-ican3 CAN driver, from Ira W Snyder.

 9) Fix oops during rmmod in ti_hecc CAN driver, from Marc Kleine-Budde.

10) The removal of the conditional compilation of the clk support code
    in the stmmac driver broke things.  This is because the interfaces
    used are the ones that don't also perform the enable/disable of the
    clk.  Fix from Stefan Roese.

11) The QFQ packet scheduler can record out of range virtual start
    times, resulting later in misbehavior and even crashes.  Fix from
    Paolo Valente.

12) If MSG_WAITALL is used with IOAT DMA under TCP, we can wedge the
    receiver when the advertised receive window goes to zero.  Detect
    this case and force the processing of the IOAT DMA queue when it
    happens to avoid getting stuck.  Fix from Michal Kubecek.

13) batman-adv assumes that test_bit() returns only 0 or 1, but this is
    not true for x86 (which returns -1 or 0, via the 'sbb' instruction).
    Fix from Linus Lussing.

14) Fix small packet corruption in e1000, from Tushar Dave.

15) make_blackhole() in the IPSEC policy code can do one read unlock too
    many, fix from Li RongQing.

16) The new tcp_try_coalesce() code introduced a bug in TCP URG
    handling, fix from Eric Dumazet.

17) Fix memory leak in __netif_receive_skb() when doing zerocopy and
    when hit an OOM condition.  From Michael S Tsirkin.

18) netxen blindly deferences pdev->bus->self, which is not guarenteed
    to be non-NULL.  Fix from Nikolay Aleksandrov.

19) Fix a performance regression caused by mistakes in ipv6 checksum
    validation in the bnx2x driver, fix from Michal Schmidt.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
  net/stmmac: Use clk_prepare_enable and clk_disable_unprepare
  net: change return values from -EACCES to -EPERM
  net/irda: sh_sir: fix return value check in sh_sir_set_baudrate()
  stmmac: fix return value check in stmmac_open_ext_timer()
  gianfar: fix phc index build failure
  ipv6: fix return value check in fib6_add()
  bnx2x: remove false warning regarding interrupt number
  can: ti_hecc: fix oops during rmmod
  can: janz-ican3: fix support for older hardware revisions
  net: do not disable sg for packets requiring no checksum
  aoe: assert AoE packets marked as requiring no checksum
  at91ether: return PTR_ERR if call to clk_get fails
  xfrm_user: don't copy esn replay window twice for new states
  xfrm_user: ensure user supplied esn replay window is valid
  xfrm_user: fix info leak in copy_to_user_tmpl()
  xfrm_user: fix info leak in copy_to_user_policy()
  xfrm_user: fix info leak in copy_to_user_state()
  xfrm_user: fix info leak in copy_to_user_auth()
  net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200
  tcp: restore rcv_wscale in a repair mode (v2)
  ...

Pull sparc updates from David Miller:

1) Debugging builds on 32-bit sparc need to handle the R_SPARC_DISP32
   relocation, not just 64-bit sparc.  From Andreas Larsson.

2) Wei Yongjun noticed that module_alloc() on sparc can return an
   error pointer, but that's not allowed.  module_alloc() should
   return only a valid pointer, or NULL.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: fix the return value of module_alloc()
  sparc32: Enable the relocation target R_SPARC_DISP32 for sparc32

Pull x86 fixes from Ingo Molnar:
 "Small fixlets"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/init.c: Fix devmem_is_allowed() off by one
  x86/kconfig: Remove outdated reference to Intel CPUs in CONFIG_SWIOTLB

Pull timer fix from Ingo Molnar:
 "One more timekeeping fix for v3.6"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Fix timeekeping_get_ns overflow on 32bit systems

Pull perf fixes from Ingo Molnar:
 "Small perf fixlets"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracing: Don't call page_to_pfn() if page is NULL
  perf/x86: Fix Intel Ivy Bridge support
  perf/x86/ibs: Check syscall attribute flags
  perf/x86: Export Sandy Bridge uncore clockticks event in sysfs

Pull xfs bugfixes from Ben Myers:
 - fix a regression related to xfs_sync_worker racing with unmount.
 - fix a race while discarding xfs buffers.

* tag 'for-linus-v3.6-rc7' of git://oss.sgi.com/xfs/xfs:
  xfs: stop the sync worker before xfs_unmountfs
  xfs: fix race while discarding buffers [V4]

Pull drm fixes from Dave Airlie:
 "Fixes for big 3 drivers:

  nouveau: revert earlier MBP fix, put a dmi based MBP fix in its place
  (fixes a regression we found on some Dell eDP panels doing some
  internal testing)

  radeon: revert pll fixes, real fix is too invasive, fix scratch leak

  intel: 3 minor fixes, one for HDMI audio."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: add dmi quirk for gpio reset
  drm/radeon: Prevent leak of scratch register on resume from suspend
  Revert "drm/nv50-/gpio: initialise to vbios defaults during init"
  Revert "drm/radeon: rework pll selection (v3)"
  drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
  drm/i915: Reduce a pin-leak BUG into a WARN
  drm/i915: enable lvds pin pairs before dpll on gen2

Pull input updates from Dmitry Torokhov:
 "Updates for the input subsystem.  Just a few driver updates mostly
  dealing with recent regressions."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: edt-ft5x06 - return -EFAULT on copy_to_user() error
  Input: sentelic - filter out erratic movement when lifting finger
  Input: ambakmi - [un]prepare clocks when enabling amd disabling
  Input: i8042 - disable mux on Toshiba C850D
  Revert "input: ab8500-ponkey: Create AB8500 domain IRQ mapping"
  Input: imx_keypad - fix missing clk conversions
  Input: usbtouchscreen - initialize eGalax devices

Pull watchdog fixes from Wim Van Sebroeck:
 "Fix a kdump issue in hpwdt and a possible NULL dereference."

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: move the dereference below the NULL test
  hpwdt: Fix kdump issue in hpwdt

Pull hwmon fixes from Guenter Roeck:
 - Add missing 'name' sysfs attributes to ad7314 and ads7871 drivers
 - Bump maximum wait time for applesmc driver (again)
 - Fix build warning seen with W=1 in include/linux/kernel.h, introduced
   with commit b6d86d3d ("Fix DIV_ROUND_CLOSEST to support negative
   dividends")

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  linux/kernel.h: Fix warning seen with W=1 due to change in DIV_ROUND_CLOSEST
  hwmon: (applesmc) Bump max wait
  hwmon: (ad7314) Add 'name' sysfs attribute
  hwmon: (ads7871) Add 'name' sysfs attribute

Pull slave-dmaengine fixes from Vinod Koul:
 "There are two trivial fixes in pl330 driver and two in at_hdmac
  driver."

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  DMA: PL330: Check the pointer returned by kzalloc
  DMA: PL330: Fix potential NULL pointer dereference in pl330_submit_req()
  dmaengine: at_hdmac: check that each sg data length is non-null
  dmaengine: at_hdmac: fix comment in atc_prep_slave_sg()