Prior to this patch the driver requires two IRQs to function properly,
one required IRQ for control and at least one required IRQ for IO.

This requirement can be relaxed to one as the driver now allows
sharing of IRQs, so control and IO EQs can share the same irq.

This is needed for high scale amount of VFs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Control IRQ is the first IRQ vector. This complicates handling of
completion irqs as we need to offset them by one.
in the next patch, there are scenarios where completion and control EQs
will share the same irq. for example: functions with single IRQ. To ease
such scenarios, we shift control IRQ to the end of the irq array.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Create lowest priority flow group in egress table with single rule that
matches on special reg_c1 value that is set on ingress VLAN push with
single action that pops VLAN. The flow destination is skip table that is
used to skip any further processing of packet in FDB bridge priority.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

On ingress VLAN push also assign value 0x7FE to reg_c1 tunnel id+opts
bits (tunnel id 0, which is not a valid tunnel id, and option 0x7FE which
was reserved by one of previous patches in the series). In following patch
the reg value is matched on egress miss to restore the packet to its
original state by removing the VLAN before passing it to the software data
path.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Following patches in series need to pop VLAN when packet misses on egress.
To reuse existing bridge VLAN pop handling code, extract it to dedicated
helpers mlx5_esw_bridge_pkt_reformat_vlan_pop_supported() and
mlx5_esw_bridge_pkt_reformat_vlan_pop_create().
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Several functions in bridge.c excessively obtain pointer to parent eswitch
instance by dereferencing br_offloads->esw on every usage and following
patches in this series add even more usages of eswitch. Introduce local
variable 'esw' and use it instead.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Support TC generic 'accept' action in mlx5 by introducing
MLX5_ESW_ATTR_FLAG_ACCEPT attribute flag. Flag has similar semantics to
existing MLX5_ESW_ATTR_FLAG_SLOW_PATH flag, however, dedicated flag is
required because existing 'slow path' flag can be flipped by tunneling
subsystem when neighbor changes state.

Introduce new helper function mlx5_esw_attr_flags_skip() to check whether
attribute flags for 'slow path' or 'accept' action are set and use it in
eswitch code instead of direct bit manipulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There is a use case that the local and remote VTEPs are in the same
host. Currently, the out ifindex is not specified when looking up the
encap route for offloads. So in this case, a local route is returned
and the route dev is lo.

Actual tunnel interface can be created with a parameter "dev" [1],
which specifies the physical device to use for tunnel endpoint
communication. Pass this parameter to driver when looking up encap
route for offloads. So that a unicast route will be returned.

[1] ip link add name vxlan1 type vxlan id 100 dev enp4s0f0 remote 1.1.1.1 dstport 4789
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Reserve one more value from TC tunnel options range to be used by bridge
offload in following patches.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The parse fdb/nic actions funcs parse the actions and then call
actions_match_supported() for final check.
Move related check in parse_tc_fdb_actions() into
actions_match_supported_fdb() for more organized code.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

There will probably be more checks, some for nic flows, some for fdb
flows and some are shared checks. Split it for fdb and nic to avoid
the function getting too big.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Move mod hdr allocation chunk from parse_tc_fdb_actions() and
parse_tc_nic_actions() to a shared function.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Refactor sample unoffload to be symmetric to sample offload.
Use the existing del_post_rule() to release the post rule.
Also mlx5e_tc_sample_unoffload() should not return post_rule
which is NULL when post actions are supported.
Sample offload works with this NULL because many places of the
code use IS_ERR() instead of IS_ERR_OR_NULL() to check rule is valid
and when rule is detected as sample offload the code is not using the
rule. Let's be persistent and avoid returning NULL anyway and return the
pre rule, like in CT case, which is not NULL.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add driver max_rate support for the MQPRIO bw_rlimit shaper
in channel mode.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Let the caller of mlx5e_open_txqsq() directly pass the SQ stats
structure pointer.
This replaces logic involving the qos_queue_group_id parameter,
and helps generalizing its role in the next patch.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Russell King says:

====================
Add phylink helper for 10G modes

During the last cycle, there was discussion about adding a helper
to set the 10G link modes for phylink, which resulted in these two
patches introduce such a helper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update three drivers to use the new phylink_set_10g_modes() helper:
Cadence macb, Freescale DPAA2 and Marvell PP2.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

sdata->tun_src should be freed before sdata is freed
because sdata->tun_src is allocated after sdata allocation.
So, kfree(sdata) and kfree(rcu_dereference_raw(sdata->tun_src)) are
changed code order.

Fixes: f04ed7d2 ("net: ipv6: check return value of rhashtable_init")
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prabhakar Kushwaha says:

====================
qed: new firmware version 8.59.1.0 support

This series integrate new firmware version 8.59.1.0, along with updated
HSI (hardware software interface) to use the FW, into the family of
qed drivers (fastlinq devices). This FW does not reside in the NVRAM.
It needs to be programmed to device during driver load as the part of
initialization sequence.

Similar to previous FW support series, this FW is tightly linked to
software and pf function driver. This means FW release is not backward
compatible, and driver should always run with the FW it was designed
against.

FW binary blob is already submitted & accepted in linux-firmware repo.

Patches in the series include:
patch 1     - qed: Fix kernel-doc warnings
patch 2     - qed: Remove e4_ and _e4 from FW HSI
patch 3     - qed: split huge qed_hsi.h header file
patch 4-8   - HSI (hardware software interface) changes
patch 9     - qed: Add '_GTT' suffix to the IRO RAM macros
patch 10    - qed: Update debug related changes
patch 11    - qed: rdma: Update TCP silly-window-syndrome timeout
patch 12    - qed: Update the TCP active termination 2  MSL timer
patch 13    - qed: fix ll2 establishment during load of RDMA driver

In addition, this patch series also fixes existing checkpatch warnings
and checks which are missing.

Changes for v2:
 - Incorporated Jakub's comments.
   - New patch introduced to fix all kernel-doc issue in qed driver.
   - Fixed warning: ‘qed_mfw_ext_20g’ defined but not used.
   - Fixed warning related to kernel-doc wrt to this series.
   - Removed inline function declaration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If stats ID of a LL2 (light l2) queue exceeds than the total amount
of statistics counters, it may cause system crash upon enabling
RDMA on all PFs.

This patch makes sure that the stats ID of the LL2 queue doesn't exceed
the max allowed value.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize 2 MSL timeout value used for the TCP TIME_WAIT state to
non-zero default.

This patch also removes magic number from qedi/qedi_main.c.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update TCP silly-window-syndrome timeout, for the cases where
initiator's small TCP window size prevents FW from transmitting
packets on the connection. Timeout causes FW to retransmit
window probes if needed, preventing I/O stall if initiator ignores
first window probe.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed_debug features are updated to support FW version 8.59.1.0 along
with few enhancements.
  - Removal of _BB_K2 from register defines.
  - Add new condition cond14.
  - Add dump of new area sw-platform, epoch, iscsi_task_pages,
    fcoe_task_pages, roce_task_pages and eth_task_pages.
  - Introduced new functions qed_dbg_phy_size().
  - Update in qed_mcp_nvm_rd_cmd() declaration.
  - Allow QED to control init/exit at pf level.
  - Dump partial "ILT-dump" if buffer size is not sufficient.

This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GTT (Global translation table) is a fast-access window in the BAR into
the register space, which only maps certain register addresses.
This change helps enforce that only those addresses which are indeed
mapped by the GTT are being accessed through it.

Adding the '_GTT' suffix to the IRO FW memory (“RAM”) macros that
access GTT-able region in FW memories (“RAM”) and use GTT macros
to access RAM BAR from drivers.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qed_init_fw_func.c and qed_init_ops.c updated to support FW
version 8.59.1.0.
  - Support 16-bit VPORT WFQ (weighted fair queueing) weights.
  - Support WFQ (weighted fair queueing) weight per VPORT + TC.
  - Support allocation of Tx PQs(physical queues) per PF,VF.
  - Modify Global RL (rate limiter) upper bound configuration.
  - Update FW operation functions.
  - Update iro_arr[] array.

This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed_iro_hsi.h contains HSI changes related to storm memories access.
Existing code is based on hard-coded index.
Use enum as defined for FW HSI 8.59.1.0, instead of hard-coded index.

This patch also removes unnecessary header file inclusion.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qed_hsi.h has been updated to support new FW version 8.59.1.0 with
changes.
 - Updates FW HSI (Hardware Software interface) structures.
 - Addition/update in function declaration and defines as per HSI.
 - Add generic infrastructure for FW error reporting as part of
   common event queue handling.
 - Move malicious VF error reporting to FW error reporting
   infrastructure.
 - Move consolidation queue initialization from FW context to ramrod
   message.

qed_hsi.h header file changes lead to change in many files to ensure
compilation.

This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qed_mfw_hsi.h contains HSI (Hardware Software Interface) changes
related to management firmware. It has been updated to support new FW
version 8.59.1.0 with below changes.
 - New defines for VF bitmap.
 - fec_mode and extended_speed defines updated in struct eth_phy_cfg.
 - Updated structutres lldp_system_tlvs_buffer_s, public_global,
   public_port, public_func, drv_union_data, public_drv_mb
   with all dependent new structures.
 - Updates in NVM related structures and defines.
 - Msg defines are added in enum drv_msg_code and fw_msg_code.
 - Updated/added new defines.

This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The common_hsi.h has been updated for FW version 8.59.1.0 with below
changes.
  - FW and Tools version.
  - New structures related to search table, packet duplication.
  - Structure for doorbell address for legacy mode without DEM.
  - Enhanced union rdma_eqe_data for RoCE Suspend Event Data.
  - New defines.

This patch also fixes the existing checkpatch warnings and few important
checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qed_hsi.h is a huge header file containing HSI (Hardware Software
Interface) definitions of storm memory access, debug related, general
and management firmware specific. In order to have a better
code-organization HSI definition, this patch split the code across
multiple files, i.e.
- storm memory access HSI : qed_iro_hsi.h
- debug related HSI       : qed_dbg_hsi.h
- Management firmware HSI : qed_mfg_hsi.h
- General HSI             : qed_hsi.h

In addition, this patch also fixes existing checkpatch warnings and
few important checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing qed/qede/qedr/qedi/qedf code uses chip-specific naming in
structures,  functions, variables and defines in FW HSI (Hardware
Software Interface).

The new FW version introduced a generic naming convention in HSI
in-which the same code will be used across different versions
for simpler maintainability. It also eases in providing support for
new features.

With this patch every "_e4" or "e4_" prefix or suffix is not needed
anymore and it will be removed.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes all the qed and qede kernel-doc warnings
according to the guidelines that are described in
Documentation/doc-guide/kernel-doc.rst.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Justin Iurman says:

====================
Support for the ip6ip6 encapsulation of IOAM

v2:
 - add prerequisite patches
 - keep uapi backwards compatible by adding two new attributes
 - add more comments to document the ioam6_iptunnel uapi

In the current implementation, IOAM can only be inserted directly (i.e., only
inside packets generated locally) by default, to be compliant with RFC8200.

This patch adds support for in-transit packets and provides the ip6ip6
encapsulation of IOAM (RFC8200 compliant). Therefore, three ioam6 encap modes
are defined:

 - inline: directly inserts IOAM inside packets (by default).

 - encap:  ip6ip6 encapsulation of IOAM inside packets.

 - auto:   either inline mode for packets generated locally or encap mode for
           in-transit packets.

With current iproute2 implementation, it is configured this way:

$ ip -6 r [...] encap ioam6 trace prealloc [...]

The old syntax does not change (for backwards compatibility) and implicitly uses
the inline mode. With the new syntax, an encap mode can be specified:

(inline mode)
$ ip -6 r [...] encap ioam6 mode inline trace prealloc [...]

(encap mode)
$ ip -6 r [...] encap ioam6 mode encap tundst fc00::2 trace prealloc [...]

(auto mode)
$ ip -6 r [...] encap ioam6 mode auto tundst fc00::2 trace prealloc [...]

A tunnel destination address must be configured when using the encap mode or the
auto mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for testing the encap (ip6ip6) mode of IOAM.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the ip6ip6 encapsulation by providing three encap
modes: inline, encap and auto.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

This prerequisite patch provides some minor edits (alignments, renames) and a
minor modification inside a function to facilitate the next patch by using
existing nla_* functions.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch anticipates the support for the IOAM insertion inside in-transit
packets, by making a difference between input and output in order to determine
the right value for its hop-limit (inherited from the IPv6 hop-limit).

Input case: happens before ip6_forward, the IPv6 hop-limit is not decremented
yet -> decrement the IOAM hop-limit to reflect the new hop inside the trace.

Output case: happens after ip6_forward, the IPv6 hop-limit has already been
decremented -> keep the same value for the IOAM hop-limit.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch caches doorbell address directly in struct mlx4_en_tx_ring.

This removes the need to bring in cpu caches whole struct mlx4_uar
in fast path.

Note that mlx4_uar is not guaranteed to be on a local node,
because mlx4_bf_alloc() uses a single free list (priv->bf_list)
regardless of its node parameter.

This kind of change does matter in presence of light/moderate traffic.
In high stress, this read-only line would be kept hot in caches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeremy Kerr says:

====================
MCTP kunit tests

This change adds some initial kunit tests for the MCTP core. We'll
expand the coverage in a future series, and augment with a few
selftests, but this establishes a baseline set of tests for now.

Thanks to the kunit folks for the framework!

---

v2:
 - fix MCTP=m, KUNIT={y,m} breakage
 - fix mctp test netdev initialisation
 - strict route reference count checking
====================
Signed-off-by: David S. Miller <davem@davemloft.net>