This is a prerequisite to remove the static mappings for imx35 devicetree
based machines.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The fsl,panel property is deprecated and we should use the new
of_graph dt bindings to describe the relationship between the DCU
controller and the panel.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add of_graph dt nodes to describe the panel, and removed
"fsl,panel" property
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.

https://inversepath.com/usbarmorySigned-off-by: Andrej Rosano <andrej@inversepath.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Inverse Path is an information security consulting company:
https://inversepath.comSigned-off-by: Andrej Rosano <andrej@inversepath.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

WaRP7 has a BCM43430 Bluetooth chip.

Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add User Button at GPIO7_1.

Tested by evtest.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable I2C2 device support.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

IMX6UL GEA M6UL modules are system on module solutions manufactured
by Engicam with following characteristics:
Processor	Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM		128MB, 16-bit DDR3
NAND SLC	256MB
Power supply	Single 5V
MAX LCD RES	up to WXGA, 1366x768

and more info at
http://www.engicam.com/prodotti/embedded/som/sodimm/gea-m6ul

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6ul iomuxc syscon is compatible to imx6q,
so let's add compatible string 'fsl,imx6q-iomuxc-gpr'
for imx6ul iomuxc syscon node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add audio support via on module I2S SGTL5000 codec.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators. This also synchronize
the name of the +3.3V regulator with the one used in the Colibri
VF50/VF61 device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move SD-card definition to module level. While at it, also disable
write-protect since the Colibri standard does not define a pin for
SD-Card write-protection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add bindings for the Vivante GC400T GPU found in the i.MX6SX.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

sgtl5000 codec needs MCLK clock to be provided so that it can
successfully read/write via I2C, so we should better let the
codec control the pinctrl for such pin.

Thanks to Stefan Agner who provided the fix on Toradex's tree:
http://git.toradex.com/cgit/linux-toradex.git/commit/?h=toradex_imx_4.1.15_1.0.0_ga-next&id=0a55a7e5f58d46eef0d4d1d357d89e36d0c32fa4Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul-pico has WDOG1_B pin connected to the PMIC.

Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

At power on, pca953x GPIO pins are configured as input and may cause
unexpected interrupts. Configure the unused pins as GPO low to
avoid unexpected interrupts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7s-warpd has WDOG1_B pin connected to the PMIC.

Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

warp7 has a sgtl5000 audio codec.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add clock-frequency property to CPU nodes. Avoids warnings like
"/cpus/cpu@0 missing clock-frequency property".
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Only i.MX 7Dual SoC supports CPU frequencies of up to 1GHz. The i.MX
7Solo can run with up to 800MHz and does so without making use of DVFS
usually. While the device tree clearly specified a too fast operating
point for i.MX 7Solo, the kernel did not used it in practise so far
because the CPUfreq driver does not get loaded on i.MX 7Solo devices
(since the fsl,imx7s compatible string is not in the list of devices
making use of the cpufreq-dt driver...).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Apply hardware workaround for ethernet problem
See nxp erratum err006687
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the three SAI ports nodes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a SDMA entry in the dtsi file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for MPL3115 NXP pressure sensor.

Tested by reading temperature and pressure:

$ cat /sys/bus/iio/devices/iio:device0/in_temp_raw
$ cat /sys/bus/iio/devices/iio:device0/in_pressure_raw
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These device trees add support for TS-4900 by Technologic Systems.

More details here:
   http://wiki.embeddedarm.com/wiki/TS-4900Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the documentation for the TS-4900 by Technologic Systems.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
 * IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
 * small form factor (35x70mm)
 * 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
 * 256MB NAND flash (4GB option)
 * Gateworks System Controller:
  - hardware watchdog
  - hardware monitor
  - pushbutton controller
  - EEPROM storage
  - power control
 * JTAG programmable
 * 1x miniPCI socket (with PCIe, USB, SIM)
 * 1x microSD socket
 * 1x SIM socket
 * Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
 * analog CVBS video in
 * GPS (optional uBlox EVA-M8M)
 * Application headers:
  - 2x TTL UART (TX/RX)
  - 4x TTL GPIO (3x configurable as PWM)
  - 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
 * Front panel connectors:
  - micro-HDMI audio/video out
  - 1x user programmable LED
  - 1x configurable user pushbutton
  - 1x USB OTG

See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX 7 as a GICv2, hence its CPU interface register map (the
second register region) is 8kB long. Add the VGIC maintenance
interrupt which allows to use the new VGIC driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since we have a SoC level node we should make use of it and have
all nodes which are within the SoC, inside that node. This also
saves an extra interrupt-parent properties. While at it, also
order the Coresight nodes according to register addresses.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

We have the following messages that tell csi devices are not used:
imx-ipuv3 18000000.ipu: no port@0 node in /soc/ipu@18000000, not using CSI0
imx-ipuv3 18000000.ipu: no port@1 node in /soc/ipu@18000000, not using CSI1

So we add them in the common device tree to make CSI ports available on
imx53 boards.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order to use sdma with UART, we need to add DMA configuration in device tree.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul-pico-hobbit has a bcm4343 wifi chip connected to usdhc2 port.

Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SoC internal regulators for the CPU and the SoC come from the
DA9063 vdd_core and vdd_soc. Add this relationship to the device tree
so that the voltage drop on the SoC internal LDO regulators can be
minimized.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the initial support for the Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platformSigned-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

bc677ff4 adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.

This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>