- 19 Jul, 2021 17 commits
-
-
Subbaraya Sundeep authored
For enabling VF-VF switching the packets egressing out of CGX mapped VFs needed to be sent to LBK so that same packets are received back to the system. But the LBK link also needs to be enabled in addition to a VF's mapped CGX_LMAC link otherwise hardware raises send error interrupt indicating selected LBK link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register. Hence this patch enables all LBK links in TL3_TL2_LINKX_CFG registers. Also to enable packet flow between PFs/VFs of NIX0 to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC rules has to be installed such that rules must be hit for any TX interface i.e., NIX0-TX or NIX1-TX provided DMAC match creteria is met. Hence this patch changes the behavior such that MCAM is programmed to match with any NIX0/1-TX interface for TX rules. Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
tfo_active_disable_stamp is read and written locklessly. We need to annotate these accesses appropriately. Then, we need to perform the atomic_inc(tfo_active_disable_times) after the timestamp has been updated, and thus add barriers to make sure tcp_fastopen_active_should_disable() wont read a stale timestamp. Fixes: cf1ef3f0 ("net/tcp_fastopen: Disable active side TFO in certain scenarios") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Joakim Zhang says: ==================== dt-bindings: net: dwmac-imx: convert This patch set intends to convert imx dwmac binding to schema, and fixes found by dt_binding_check and dtbs_check. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
This patch changs interrupt order which found by dtbs_check. $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:0: 'macirq' was expected arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:1: 'eth_wake_irq' was expected According to Documentation/devicetree/bindings/net/snps,dwmac.yaml, we should list interrupt in it's order. Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
In order to automate the verification of DT nodes covert imx-dwmac to nxp,dwmac-imx.yaml, and pass below checking. $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
Add missing DWMAC IP version in snps,dwmac.yaml which found by below command, as NXP i.MX8 families support SNPS DWMAC 5.10a IP. $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml Documentation/devicetree/bindings/net/nxp,dwmac-imx.example.dt.yaml: ethernet@30bf0000: compatible: None of ['nxp,imx8mp-dwmac-eqos', 'snps,dwmac-5.10a'] are valid under the given schema Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
Building on ARCH=arc causes a "redefined" warning, so rename this driver's CACHE_LINE_MASK to avoid the warning. ../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined 134 | #define CACHE_LINE_MASK 0x3F In file included from ../include/linux/cache.h:6, from ../include/linux/printk.h:9, from ../include/linux/kernel.h:19, from ../include/linux/list.h:9, from ../include/linux/module.h:12, from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7: ../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition 17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1)) Fixes: d413779c ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Bug fixes Most of the fixes in this series have to do with error recovery. They include error path handling when the error recovery has to abort, and the rediscovery of capabilities (PTP and RoCE) after firmware reset that may result in capability changes. Two other fixes are to reject invalid ETS settings and to validate VLAN protocol in the RX path. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
The current PTP initialization logic does not account for firmware reset that may cause PTP capability to change. The valid pointer bp->ptp_cfg is used to indicate that the device is capable of PTP and that it has been initialized. So we must clean up bp->ptp_cfg and free it if the firmware after reset does not support PTP. Fixes: 93cb62d9 ("bnxt_en: Enable hardware PTP support") Cc: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
The device needs to be in ifup state for PTP to function, so move bnxt_ptp_init() to bnxt_open(). This means that the PHC will be registered during bnxt_open(). This also makes firmware reset work correctly. PTP configurations may change after firmware upgrade or downgrade. bnxt_open() will be called after firmware reset, so it will work properly. bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now also need to call bnxt_ptp_clear() in bnxt_close(). Fixes: 93cb62d9 ("bnxt_en: Enable hardware PTP support") Cc: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Somnath Kotur authored
bnxt_half_open_nic() is called during during ethtool self test and is protected by rtnl_lock. Firmware reset can be happening at the same time. Only critical portions of the entire firmware reset sequence are protected by the rtnl_lock. It is possible that bnxt_half_open_nic() can be called when the firmware reset sequence is aborting. In that case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set and abort if it is. The ethtool self test will fail but the NIC will be brought to a consistent IF_DOWN state. Without this patch, if bnxt_half_open_nic() were to continue in this error state, it may crash like this: bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 ... Process ethtool (pid: 333327, stack limit = 0x0000000046476577) Call trace: bnxt_alloc_mem+0x444/0xef0 [bnxt_en] bnxt_half_open_nic+0x24/0xb8 [bnxt_en] bnxt_self_test+0x2dc/0x390 [bnxt_en] ethtool_self_test+0xe0/0x1f8 dev_ethtool+0x1744/0x22d0 dev_ioctl+0x190/0x3e0 sock_ioctl+0x238/0x480 do_vfs_ioctl+0xc4/0x758 ksys_ioctl+0x84/0xb8 __arm64_sys_ioctl+0x28/0x38 el0_svc_handler+0xb0/0x180 el0_svc+0x8/0xc Fixes: a1301f08 ("bnxt_en: Check abort error state in bnxt_open_nic().") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
Only pass supported VLAN protocol IDs for stripped VLAN tags to the stack. The stack will hit WARN() if the protocol ID is unsupported. Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100. Only the 1st two protocols are supported by the kernel. Fixes: a196e96b ("bnxt_en: clean up VLAN feature bit handling") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Somnath Kotur authored
When bnxt_open() fails in the firmware reset path, the driver needs to gracefully abort, but it is executing code that should be invoked only in the success path. Define a function to abort FW reset and consolidate all error paths to call this new function. Fixes: dab62e7c ("bnxt_en: Implement faster recovery for firmware fatal error.") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after we acquire the rtnl_lock. If the flag is set, we need to abort. Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
The capabilities can change after firmware upgrade/downgrade, so we should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe() is called. Fixes: 2151fe08 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Edwin Peer authored
ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum bandwidth constraints. Thus, zero is a legal value for a given TC. However, if all the other TCs sum up to 100%, then at least one hardware queue will starve, resulting in guaranteed TX timeouts. Reject such nonsensical configurations. Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kalesh AP authored
If device is already disabled in reset path and PCI io error is detected before the device could be enabled, driver could call pci_disable_device() for already disabled device. Fix this problem by calling pci_disable_device() only if the device is already enabled. Fixes: 6316ea6d ("bnxt_en: Enable AER support.") Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 18 Jul, 2021 4 commits
-
-
Nguyen Dinh Phi authored
Commit 63346650 ("netrom: switch to sock timer API") switched to use sock timer API. It replaces mod_timer() by sk_reset_timer(), and del_timer() by sk_stop_timer(). Function sk_reset_timer() will increase the refcount of sock if it is called on an inactive timer, hence, in case the timer expires, we need to decrease the refcount ourselves in the handler, otherwise, the sock refcount will be unbalanced and the sock will never be freed. Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com> Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com Fixes: 63346650 ("netrom: switch to sock timer API") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
After commit ca84bd05 ("sctp: copy the optval from user space in sctp_setsockopt"), it does memory allocation in sctp_setsockopt with the optlen, and it would fail the allocation and return error if the optlen from user space is a huge value. This breaks some sockopts, like SCTP_HMAC_IDENT, SCTP_RESET_STREAMS and SCTP_AUTH_KEY, as when processing these sockopts before, optlen would be trimmed to a biggest value it needs when optlen is a huge value, instead of failing the allocation and returning error. This patch is to fix the allocation failure when it's a huge optlen from user space by trimming it to the biggest size sctp sockopt may need when necessary, and this biggest size is from sctp_setsockopt_reset_streams() for SCTP_RESET_STREAMS, which is bigger than those for SCTP_HMAC_IDENT and SCTP_AUTH_KEY. Fixes: ca84bd05 ("sctp: copy the optval from user space in sctp_setsockopt") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Skripkin authored
Syzbot reported memory leak in tcindex_set_parms(). The problem was in non-freed perfect hash in tcindex_partial_destroy_work(). In tcindex_set_parms() new tcindex_data is allocated and some fields from old one are copied to new one, but not the perfect hash. Since tcindex_partial_destroy_work() is the destroy function for old tcindex_data, we need to free perfect hash to avoid memory leak. Reported-and-tested-by: syzbot+f0bbb2287b8993d4fa74@syzkaller.appspotmail.com Fixes: 331b7292 ("net: sched: RCU cls_tcindex") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pravin B Shelar authored
In some cases skb head could be locked and entire header data is pulled from skb. When skb_zerocopy() called in such cases, following BUG is triggered. This patch fixes it by copying entire skb in such cases. This could be optimized incase this is performance bottleneck. ---8<--- kernel BUG at net/core/skbuff.c:2961! invalid opcode: 0000 [#1] SMP PTI CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:skb_zerocopy+0x37a/0x3a0 RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246 Call Trace: <IRQ> queue_userspace_packet+0x2af/0x5e0 [openvswitch] ovs_dp_upcall+0x3d/0x60 [openvswitch] ovs_dp_process_packet+0x125/0x150 [openvswitch] ovs_vport_receive+0x77/0xd0 [openvswitch] netdev_port_receive+0x87/0x130 [openvswitch] netdev_frame_hook+0x4b/0x60 [openvswitch] __netif_receive_skb_core+0x2b4/0xc90 __netif_receive_skb_one_core+0x3f/0xa0 __netif_receive_skb+0x18/0x60 process_backlog+0xa9/0x160 net_rx_action+0x142/0x390 __do_softirq+0xe1/0x2d6 irq_exit+0xae/0xb0 do_IRQ+0x5a/0xf0 common_interrupt+0xf/0xf Code that triggered BUG: int skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen) { int i, j = 0; int plen = 0; /* length of skb->head fragment */ int ret; struct page *page; unsigned int offset; BUG_ON(!from->head_frag && !hlen); Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 17 Jul, 2021 1 commit
-
-
Mahesh Bandewar authored
The commit 9a560550 (" bonding: Add struct bond_ipesc to manage SA") is causing following build error when XFRM is not selected in kernel config. lld: error: undefined symbol: xfrm_dev_state_flush >>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453) >>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a Fixes: 9a560550 (" bonding: Add struct bond_ipesc to manage SA") Signed-off-by: Mahesh Bandewar <maheshb@google.com> CC: Taehee Yoo <ap420073@gmail.com> CC: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 16 Jul, 2021 3 commits
-
-
Yajun Deng authored
The release_sock() is blocking function, it would change the state after sleeping. use wait_woken() instead. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Woudstra authored
According to reference guides mt7530 (mt7620) and mt7531: NOTE: When IVL is reset, MAC[47:0] and FID[2:0] will be used to read/write the address table. When IVL is set, MAC[47:0] and CVID[11:0] will be used to read/write the address table. Since the function only fills in CVID and no FID, we need to set the IVL bit. The existing code does not set it. This is a fix for the issue I dropped here earlier: http://lists.infradead.org/pipermail/linux-mediatek/2021-June/025697.html With this patch, it is now possible to delete the 'self' fdb entry manually. However, wifi roaming still has the same issue, the entry does not get deleted automatically. Wifi roaming also needs a fix somewhere else to function correctly in combination with vlan. Signed-off-by: Eric Woudstra <ericwouds@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ilias Apalodimas authored
As Alexander points out, when we are trying to recycle a cloned/expanded SKB we might trigger a race. The recycling code relies on the pp_recycle bit to trigger, which we carry over to cloned SKBs. If that cloned SKB gets expanded or if we get references to the frags, call skb_release_data() and overwrite skb->head, we are creating separate instances accessing the same page frags. Since the skb_release_data() will first try to recycle the frags, there's a potential race between the original and cloned SKB, since both will have the pp_recycle bit set. Fix this by explicitly those SKBs not recyclable. The atomic_sub_return effectively limits us to a single release case, and when we are calling skb_release_data we are also releasing the option to perform the recycling, or releasing the pages from the page pool. Fixes: 6a5bcd84 ("page_pool: Allow drivers to hint on SKB recycling") Reported-by: Alexander Duyck <alexanderduyck@fb.com> Suggested-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 15 Jul, 2021 14 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Andrii Nakryiko says: ==================== pull-request: bpf 2021-07-15 The following pull-request contains BPF updates for your *net* tree. We've added 9 non-merge commits during the last 5 day(s) which contain a total of 9 files changed, 37 insertions(+), 15 deletions(-). The main changes are: 1) Fix NULL pointer dereference in BPF_TEST_RUN for BPF_XDP_DEVMAP and BPF_XDP_CPUMAP programs, from Xuan Zhuo. 2) Fix use-after-free of net_device in XDP bpf_link, from Xuan Zhuo. 3) Follow-up fix to subprog poke descriptor use-after-free problem, from Daniel Borkmann and John Fastabend. 4) Fix out-of-range array access in s390 BPF JIT backend, from Colin Ian King. 5) Fix memory leak in BPF sockmap, from John Fastabend. 6) Fix for sockmap to prevent proc stats reporting bug, from John Fastabend and Jakub Sitnicki. 7) Fix NULL pointer dereference in bpftool, from Tobias Klauser. 8) AF_XDP documentation fixes, from Baruch Siach. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dongliang Mu authored
The current error handling code of hso_create_net_device is hso_free_net_device, no matter which errors lead to. For example, WARNING in hso_free_net_device [1]. Fix this by refactoring the error handling code of hso_create_net_device by handling different errors by different code. [1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com Fixes: 5fcfb6d0 ("hso: fix bailout in error case of probe") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jia He authored
Liajian reported a bug_on hit on a ThunderX2 arm64 server with FastLinQ QL41000 ethernet controller: BUG: scheduling while atomic: kworker/0:4/531/0x00000200 [qed_probe:488()]hw prepare failed kernel BUG at mm/vmalloc.c:2355! Internal error: Oops - BUG: 0 [#1] SMP CPU: 0 PID: 531 Comm: kworker/0:4 Tainted: G W 5.4.0-77-generic #86-Ubuntu pstate: 00400009 (nzcv daif +PAN -UAO) Call trace: vunmap+0x4c/0x50 iounmap+0x48/0x58 qed_free_pci+0x60/0x80 [qed] qed_probe+0x35c/0x688 [qed] __qede_probe+0x88/0x5c8 [qede] qede_probe+0x60/0xe0 [qede] local_pci_probe+0x48/0xa0 work_for_cpu_fn+0x24/0x38 process_one_work+0x1d0/0x468 worker_thread+0x238/0x4e0 kthread+0xf0/0x118 ret_from_fork+0x10/0x18 In this case, qed_hw_prepare() returns error due to hw/fw error, but in theory work queue should be in process context instead of interrupt. The root cause might be the unpaired spin_{un}lock_bh() in _qed_mcp_cmd_and_union(), which causes botton half is disabled incorrectly. Reported-by: Lijian Zhang <Lijian.Zhang@arm.com> Signed-off-by: Jia He <justin.he@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ziyang Xuan authored
When nr_segs equal to zero in iovec_from_user, the object msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg which is defined in ___sys_sendmsg. So we cann't just judge msg->msg_iter.iov->base directlly. We can use nr_segs to judge msg in caif_seqpkt_sendmsg whether has data buffers. ===================================================== BUG: KMSAN: uninit-value in caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 caif_seqpkt_sendmsg+0x693/0xf60 net/caif/caif_socket.c:542 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg net/socket.c:672 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2343 ___sys_sendmsg net/socket.c:2397 [inline] __sys_sendmmsg+0x808/0xc90 net/socket.c:2480 __compat_sys_sendmmsg net/compat.c:656 [inline] Reported-by: syzbot+09a5d591c1f98cf5efcb@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=1ace85e8fc9b0d5a45c08c2656c3e91762daa9b8 Fixes: bece7b23 ("caif: Rewritten socket implementation") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tobias Klauser authored
Fix and add a missing NULL check for the prior malloc() call. Fixes: 49a086c2 ("bpftool: implement prog load command") Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Acked-by: Roman Gushchin <guro@fb.com> Link: https://lore.kernel.org/bpf/20210715110609.29364-1-tklauser@distanz.ch
-
Jakub Sitnicki authored
The proc socket stats use sk_prot->inuse_idx value to record inuse sock stats. We currently do not set this correctly from sockmap side. The result is reading sock stats '/proc/net/sockstat' gives incorrect values. The socket counter is incremented correctly, but because we don't set the counter correctly when we replace sk_prot we may omit the decrement. To get the correct inuse_idx value move the core_initcall that initializes the UDP proto handlers to late_initcall. This way it is initialized after UDP has the chance to assign the inuse_idx value from the register protocol handler. Fixes: edc6741c ("bpf: Add sockmap hooks for UDP sockets") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Cong Wang <cong.wang@bytedance.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20210714154750.528206-1-jakub@cloudflare.com
-
John Fastabend authored
The proc socket stats use sk_prot->inuse_idx value to record inuse sock stats. We currently do not set this correctly from sockmap side. The result is reading sock stats '/proc/net/sockstat' gives incorrect values. The socket counter is incremented correctly, but because we don't set the counter correctly when we replace sk_prot we may omit the decrement. To get the correct inuse_idx value move the core_initcall that initializes the TCP proto handlers to late_initcall. This way it is initialized after TCP has the chance to assign the inuse_idx value from the register protocol handler. Fixes: 604326b4 ("bpf, sockmap: convert to generic sk_msg interface") Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/bpf/20210712195546.423990-3-john.fastabend@gmail.com
-
John Fastabend authored
If skb_linearize is needed and fails we could leak a msg on the error handling. To fix ensure we kfree the msg block before returning error. Found during code review. Fixes: 4363023d ("bpf, sockmap: Avoid failures from skb_to_sgvec when skb has frag_list") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/bpf/20210712195546.423990-2-john.fastabend@gmail.com
-
Colin Ian King authored
Currently array jit->seen_reg[r1] is being accessed before the range checking of index r1. The range changing on r1 should be performed first since it will avoid any potential out-of-range accesses on the array seen_reg[] and also it is more optimal to perform checks on r1 before fetching data from the array. Fix this by swapping the order of the checks before the array access. Fixes: 05462310 ("s390/bpf: Add s390x eBPF JIT compiler backend") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Ilya Leoshkevich <iii@linux.ibm.com> Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com
-
Qitao Xu authored
Tracepoint trace_qdisc_enqueue() is introduced to trace skb at the entrance of TC layer on TX side. This is similar to trace_qdisc_dequeue(): 1. For both we only trace successful cases. The failure cases can be traced via trace_kfree_skb(). 2. They are called at entrance or exit of TC layer, not for each ->enqueue() or ->dequeue(). This is intentional, because we want to make trace_qdisc_enqueue() symmetric to trace_qdisc_dequeue(), which is easier to use. The return value of qdisc_enqueue() is not interesting here, we have Qdisc's drop packets in ->dequeue(), it is impossible to trace them even if we have the return value, the only way to trace them is tracing kfree_skb(). We only add information we need to trace ring buffer. If any other information is needed, it is easy to extend it without breaking ABI, see commit 3dd344ea ("net: tracepoint: exposing sk_family in all tcp:tracepoints"). Reviewed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Qitao Xu <qitao.xu@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Qitao Xu authored
Print format of skbaddr is changed to %px from %p, because we want to use skb address as a quick way to identify a packet. Note, trace ring buffer is only accessible to privileged users, it is safe to use a real kernel address here. Reviewed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Qitao Xu <qitao.xu@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Qitao Xu authored
The print format of skb adress in tracepoint class net_dev_template is changed to %px from %p, because we want to use skb address as a quick way to identify a packet. Note, trace ring buffer is only accessible to privileged users, it is safe to use a real kernel address here. Reviewed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Qitao Xu <qitao.xu@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS (29) bits will be promoted to a 32 bit signed int and then sign-extended to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7) the shifted value will be sign extended and the top 32 bits of the result will be set. Fix this by casting the u16 values to a u64 before the 29 bit left shift. Addresses-Coverity: ("Unintended sign extension") Fixes: 3451b97c ("liquidio: CN23XX register setup") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Geert Uytterhoeven authored
Making global2 support mandatory removed the Kconfig symbol NET_DSA_MV88E6XXX_GLOBAL2. This symbol also served as an intermediate symbol to make NET_DSA_MV88E6XXX_PTP depend on NET_DSA_MV88E6XXX. With the symbol removed, the user is always asked about PTP support for Marvell 88E6xxx switches, even if the latter support is not enabled. Fix this by reinstating the dependency. Fixes: 63368a74 ("net: dsa: mv88e6xxx: Make global2 support mandatory") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Jul, 2021 1 commit
-
-
David S. Miller authored
Takashi Iwai says: ==================== r8152: Fix a couple of PM problems it seems that r8152 driver suffers from the deadlock at both runtime and system PM. Formerly, it was seen more often at hibernation resume, but now it's triggered more frequently, as reported in SUSE Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1186194 While debugging the problem, I stumbled on a few obvious bugs and here is the results with two patches for addressing the resume problem. *** However, the story doesn't end here, unfortunately, and those patches don't seem sufficing. The rest major problem is that the driver calls napi_disable() and napi_enable() in the PM suspend callbacks. This makes the system stalling at (runtime-)suspend. If we drop napi_disable() and napi_enable() calls in the PM suspend callbacks, it starts working (that was the result in Bugzilla comment 13): https://bugzilla.suse.com/show_bug.cgi?id=1186194#c13 So, my patches aren't enough and we still need to investigate further. It'd be appreciated if anyone can give a fix or a hint for more debugging. The usage of napi_disable() at PM callbacks is unique in this driver and looks rather suspicious to me; but I'm no expert in this area so I might be wrong... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-