- 02 Aug, 2024 12 commits
-
-
Praveen Kaligineedi authored
GVE driver wrongly relies on netif_carrier_ok() to check the interface administrative state when resources are being allocated/deallocated for queue(s). netif_carrier_ok() needs to be replaced with netif_running() for all such cases. Administrative state is the result of "ip link set dev <dev> up/down". It reflects whether the administrator wants to use the device for traffic and the corresponding resources have been allocated. Fixes: 5f08cd3d ("gve: Alloc before freeing when adjusting queues") Signed-off-by:
Praveen Kaligineedi <pkaligineedi@google.com> Reviewed-by:
Shailend Chand <shailend@google.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20240801205619.987396-1-pkaligineedi@google.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Kyle Swenson authored
The DEVID register contains two pieces of information: the device ID in the upper nibble, and the silicon revision number in the lower nibble. The driver should work fine with any silicon revision, so let's mask that out in the device ID check. Fixes: 20e6d190 ("net: pse-pd: Add TI TPS23881 PSE controller driver") Signed-off-by:
Kyle Swenson <kyle.swenson@est.tech> Reviewed-by:
Thomas Petazzoni <thomas.petazzoni@bootlin.com> Acked-by:
Oleksij Rempel <o.rempel@pengutronix.de> Link: https://patch.msgid.link/20240731154152.4020668-1-kyle.swenson@est.techSigned-off-by:
-
Kuniyuki Iwashima authored
syzbot reported a null-ptr-deref while accessing sk2->sk_reuseport_cb in reuseport_add_sock(). [0] The repro first creates a listener with SO_REUSEPORT. Then, it creates another listener on the same port and concurrently closes the first listener. The second listen() calls reuseport_add_sock() with the first listener as sk2, where sk2->sk_reuseport_cb is not expected to be cleared concurrently, but the close() does clear it by reuseport_detach_sock(). The problem is SCTP does not properly synchronise reuseport_alloc(), reuseport_add_sock(), and reuseport_detach_sock(). The caller of reuseport_alloc() and reuseport_{add,detach}_sock() must provide synchronisation for sockets that are classified into the same reuseport group. Otherwise, such sockets form multiple identical reuseport groups, and all groups except one would be silently dead. 1. Two sockets call listen() concurrently 2. No socket in the same group found in sctp_ep_hashtable[] 3. Two sockets call reuseport_alloc() and form two reuseport groups 4. Only one group hit first in __sctp_rcv_lookup_endpoint() receives incoming packets Also, the reported null-ptr-deref could occur. TCP/UDP guarantees that would not happen by holding the hash bucket lock. Let's apply the locking strategy to __sctp_hash_endpoint() and __sctp_unhash_endpoint(). [0]: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 1 UID: 0 PID: 10230 Comm: syz-executor119 Not tainted 6.10.0-syzkaller-12585-g301927d2 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024 RIP: 0010:reuseport_add_sock+0x27e/0x5e0 net/core/sock_reuseport.c:350 Code: 00 0f b7 5d 00 bf 01 00 00 00 89 de e8 1b a4 ff f7 83 fb 01 0f 85 a3 01 00 00 e8 6d a0 ff f7 49 8d 7e 12 48 89 f8 48 c1 e8 03 <42> 0f b6 04 28 84 c0 0f 85 4b 02 00 00 41 0f b7 5e 12 49 8d 7e 14 RSP: 0018:ffffc9000b947c98 EFLAGS: 00010202 RAX: 0000000000000002 RBX: ffff8880252ddf98 RCX: ffff888079478000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000012 RBP: 0000000000000001 R08: ffffffff8993e18d R09: 1ffffffff1fef385 R10: dffffc0000000000 R11: fffffbfff1fef386 R12: ffff8880252ddac0 R13: dffffc0000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f24e45b96c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffcced5f7b8 CR3: 00000000241be000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __sctp_hash_endpoint net/sctp/input.c:762 [inline] sctp_hash_endpoint+0x52a/0x600 net/sctp/input.c:790 sctp_listen_start net/sctp/socket.c:8570 [inline] sctp_inet_listen+0x767/0xa20 net/sctp/socket.c:8625 __sys_listen_socket net/socket.c:1883 [inline] __sys_listen+0x1b7/0x230 net/socket.c:1894 __do_sys_listen net/socket.c:1902 [inline] __se_sys_listen net/socket.c:1900 [inline] __x64_sys_listen+0x5a/0x70 net/socket.c:1900 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f24e46039b9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 91 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f24e45b9228 EFLAGS: 00000246 ORIG_RAX: 0000000000000032 RAX: ffffffffffffffda RBX: 00007f24e468e428 RCX: 00007f24e46039b9 RDX: 00007f24e46039b9 RSI: 0000000000000003 RDI: 0000000000000004 RBP: 00007f24e468e420 R08: 00007f24e45b96c0 R09: 00007f24e45b96c0 R10: 00007f24e45b96c0 R11: 0000000000000246 R12: 00007f24e468e42c R13: 00007f24e465a5dc R14: 0020000000000001 R15: 00007ffcced5f7d8 </TASK> Modules linked in: Fixes: 6ba84574 ("sctp: process sk_reuseport in sctp_get_port_local") Reported-by: syzbot+e6979a5d2f10ecb700e4@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=e6979a5d2f10ecb700e4 Tested-by: syzbot+e6979a5d2f10ecb700e4@syzkaller.appspotmail.com Signed-off-by:Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by:
Xin Long <lucien.xin@gmail.com> Link: https://patch.msgid.link/20240731234624.94055-1-kuniyu@amazon.comSigned-off-by:
-
Stephen Hemminger authored
The old SysKonnect NIc's are not used or actively maintained anymore. My sky2 NIC's are all in box in back corner of attic. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Link: https://patch.msgid.link/20240801162930.212299-1-stephen@networkplumber.orgSigned-off-by:
-
Jakub Kicinski authored
Matthieu Baerts says: ==================== mptcp: fix endpoints with 'signal' and 'subflow' flags When looking at improving the user experience around the MPTCP endpoints setup, I noticed that setting an endpoint with both the 'signal' and the 'subflow' flags -- as it has been done in the past by users according to bug reports we got -- was resulting on only announcing the endpoint, but not using it to create subflows: the 'subflow' flag was then ignored. My initial thought was to modify IPRoute2 to warn the user when the two flags were set, but it doesn't sound normal to ignore one of them. I then looked at modifying the kernel not to allow having the two flags set, but when discussing about that with Mat, we thought it was maybe not ideal to do that, as there might be use-cases, we might break some configs. Then I saw it was working before v5.17. So instead, I fixed the support on the kernel side (patch 5) using Paolo's suggestion. This also includes a fix on the options side (patch 1: for v5.11+), an explicit deny of some options combinations (patch 2: for v5.18+), and some refactoring (patches 3 and 4) to ease the inclusion of the patch 5. While at it, I added a new selftest (patch 7) to validate this case -- including a modification of the chk_add_nr helper to inverse the sides were the counters are checked (patch 6) -- and allowed ADD_ADDR echo just after the MP_JOIN 3WHS. The selftests modification have the same Fixes tag as the previous commit, but no 'Cc: Stable': if the backport can work, that's good -- but it still need to be verified by running the selftests -- if not, no need to worry, many CIs will use the selftests from the last stable version to validate previous stable releases. ==================== Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-0-c8a9b036493b@kernel.orgSigned-off-by:
-
Matthieu Baerts (NGI0) authored
It should be quite uncommon to set both the subflow and the signal flags: the initiator of the connection is typically the one creating new subflows, not the other peer, then no need to announce additional local addresses, and use it to create subflows. But some people might be confused about the flags, and set both "just to be sure at least the right one is set". To verify the previous fix, and avoid future regressions, this specific case is now validated: the client announces a new address, and initiates a new subflow from the same address. While working on this, another bug has been noticed, where the client reset the new subflow because an ADD_ADDR echo got received as the 3rd ACK: this new test also explicitly checks that no RST have been sent by the client and server. The 'Fixes' tag here below is the same as the one from the previous commit: this patch here is not fixing anything wrong in the selftests, but it validates the previous fix for an issue introduced by this commit ID. Fixes: 86e39e04 ("mptcp: keep track of local endpoint still available for each msk") Reviewed-by:
Mat Martineau <martineau@kernel.org> Signed-off-by:
Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20240731-upstream-net-20240731-mptcp-endp-subflow-signal-v1-7-c8a9b036493b@kernel.orgSigned-off-by:
-
Matthieu Baerts (NGI0) authored
In the following commit, the client will initiate the ADD_ADDR, instead of the server. We need to way to verify the ADD_ADDR have been correctly sent. Note: the default expected counters for when the port number is given are never changed by the caller, no need to accept them as parameter then. The 'Fixes' tag here below is the same as the one from the previous commit: this patch here is not fixing anything wrong in the selftests, but it validates the previous fix for an issue introduced by this commit ID. Fixes: 86e39e04 ("mptcp: keep track of local endpoint still available for each msk") Reviewed-by:
-
Matthieu Baerts (NGI0) authored
Up to the 'Fixes' commit, having an endpoint with both the 'signal' and 'subflow' flags, resulted in the creation of a subflow and an address announcement using the address linked to this endpoint. After this commit, only the address announcement was done, ignoring the 'subflow' flag. That's because the same bitmap is used for the two flags. It is OK to keep this single bitmap, the already selected local endpoint simply have to be re-used, but not via select_local_address() not to look at the just modified bitmap. Note that it is unusual to set the two flags together: creating a new subflow using a new local address will implicitly advertise it to the other peer. So in theory, no need to advertise it explicitly as well. Maybe there are use-cases -- the subflow might not reach the other peer that way, we can ask the other peer to try initiating the new subflow without delay -- or very likely the user is confused, and put both flags "just to be sure at least the right one is set". Still, if it is allowed, the kernel should do what has been asked: using this endpoint to announce the address and to create a new subflow from it. An alternative is to forbid the use of the two flags together, but that's probably too late, there are maybe use-cases, and it was working before. This patch will avoid people complaining subflows are not created using the endpoint they added with the 'subflow' and 'signal' flag. Note that with the current patch, the subflow might not be created in some corner cases, e.g. if the 'subflows' limit was reached when sending the ADD_ADDR, but changed later on. It is probably not worth splitting id_avail_bitmap per target ('signal', 'subflow'), which will add another large field to the msk "just" to track (again) endpoints. Anyway, currently when the limits are changed, the kernel doesn't check if new subflows can be created or removed, because we would need to keep track of the received ADD_ADDR, and more. It sounds OK to assume that the limits should be properly configured before establishing new connections. Fixes: 86e39e04 ("mptcp: keep track of local endpoint still available for each msk") Cc: stable@vger.kernel.org Suggested-by:Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Matthieu Baerts (NGI0) authored
It sounds better to avoid wasting cycles and / or put extreme memory pressure on the system by trying to create new subflows if it was not possible to add a new item in the announce list. While at it, a warning is now printed if the entry was already in the list as it should not happen with the in-kernel path-manager. With this PM, mptcp_pm_alloc_anno_list() should only fail in case of memory pressure. Fixes: b6c08380 ("mptcp: remove addr and subflow in PM netlink") Cc: stable@vger.kernel.org Suggested-by:
-
Matthieu Baerts (NGI0) authored
That will simplify the following commits. No functional changes intended. Suggested-by:
-
Matthieu Baerts (NGI0) authored
As mentioned in the 'Fixes' commit, the port flag is only supported by the 'signal' flag, and not by the 'subflow' one. Then if both the 'signal' and 'subflow' flags are set, the problem is the same: the feature cannot work with the 'subflow' flag. Technically, if both the 'signal' and 'subflow' flags are set, it will be possible to create the listening socket, but not to establish a subflow using this source port. So better to explicitly deny it, not to create some confusions because the expected behaviour is not possible. Fixes: 09f12c3a ("mptcp: allow to use port and non-signal in set_flags") Cc: stable@vger.kernel.org Reviewed-by:
-
Matthieu Baerts (NGI0) authored
Before this patch, receiving an ADD_ADDR echo on the just connected MP_JOIN subflow -- initiator side, after the MP_JOIN 3WHS -- was resulting in an MP_RESET. That's because only ACKs with a DSS or ADD_ADDRs without the echo bit were allowed. Not allowing the ADD_ADDR echo after an MP_CAPABLE 3WHS makes sense, as we are not supposed to send an ADD_ADDR before because it requires to be in full established mode first. For the MP_JOIN 3WHS, that's different: the ADD_ADDR can be sent on a previous subflow, and the ADD_ADDR echo can be received on the recently created one. The other peer will already be in fully established, so it is allowed to send that. We can then relax the conditions here to accept the ADD_ADDR echo for MPJ subflows. Fixes: 67b12f79 ("mptcp: full fully established support after ADD_ADDR") Cc: stable@vger.kernel.org Reviewed-by:
-
- 01 Aug, 2024 22 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from wireless, bleutooth, BPF and netfilter. Current release - regressions: - core: drop bad gso csum_start and offset in virtio_net_hdr - wifi: mt76: fix null pointer access in mt792x_mac_link_bss_remove - eth: tun: add missing bpf_net_ctx_clear() in do_xdp_generic() - phy: aquantia: only poll GLOBAL_CFG regs on aqr113, aqr113c and aqr115c Current release - new code bugs: - smc: prevent UAF in inet_create() - bluetooth: btmtk: fix kernel crash when entering btmtk_usb_suspend - eth: bnxt: reject unsupported hash functions Previous releases - regressions: - sched: act_ct: take care of padding in struct zones_ht_key - netfilter: fix null-ptr-deref in iptable_nat_table_init(). - tcp: adjust clamping window for applications specifying SO_RCVBUF Previous releases - always broken: - ethtool: rss: small fixes to spec and GET - mptcp: - fix signal endpoint re-add - pm: fix backup support in signal endpoints - wifi: ath12k: fix soft lockup on suspend - eth: bnxt_en: fix RSS logic in __bnxt_reserve_rings() - eth: ice: fix AF_XDP ZC timeout and concurrency issues - eth: mlx5: - fix missing lock on sync reset reload - fix error handling in irq_pool_request_irq" * tag 'net-6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits) mptcp: fix duplicate data handling mptcp: fix bad RCVPRUNED mib accounting ipv6: fix ndisc_is_useropt() handling for PIO igc: Fix double reset adapter triggered from a single taprio cmd net: MAINTAINERS: Demote Qualcomm IPA to "maintained" net: wan: fsl_qmc_hdlc: Discard received CRC net: wan: fsl_qmc_hdlc: Convert carrier_lock spinlock to a mutex net/mlx5e: Add a check for the return value from mlx5_port_set_eth_ptys net/mlx5e: Fix CT entry update leaks of modify header context net/mlx5e: Require mlx5 tc classifier action support for IPsec prio capability net/mlx5: Fix missing lock on sync reset reload net/mlx5: Lag, don't use the hardcoded value of the first port net/mlx5: DR, Fix 'stack guard page was hit' error in dr_rule net/mlx5: Fix error handling in irq_pool_request_irq net/mlx5: Always drain health in shutdown callback net: Add skbuff.h to MAINTAINERS r8169: don't increment tx_dropped in case of NETDEV_TX_BUSY netfilter: iptables: Fix potential null-ptr-deref in ip6table_nat_table_init(). netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init(). net: drop bad gso csum_start and offset in virtio_net_hdr ... -
Paolo Abeni authored
Matthieu Baerts says: ==================== mptcp: fix duplicate data handling In some cases, the subflow-level's copied_seq counter was incorrectly increased, leading to an unexpected subflow reset. Patch 1/2 fixes the RCVPRUNED MIB counter that was attached to the wrong event since its introduction in v5.14, backported to v5.11. Patch 2/2 fixes the copied_seq counter issues, is present since v5.10. Signed-off-by:
-
Paolo Abeni authored
When a subflow receives and discards duplicate data, the mptcp stack assumes that the consumed offset inside the current skb is zero. With multiple subflows receiving data simultaneously such assertion does not held true. As a result the subflow-level copied_seq will be incorrectly increased and later on the same subflow will observe a bad mapping, leading to subflow reset. Address the issue taking into account the skb consumed offset in mptcp_subflow_discard_data(). Fixes: 04e4cd4f ("mptcp: cleanup mptcp_subflow_discard_data()") Cc: stable@vger.kernel.org Link: https://github.com/multipath-tcp/mptcp_net-next/issues/501Signed-off-by:
-
Paolo Abeni authored
Since its introduction, the mentioned MIB accounted for the wrong event: wake-up being skipped as not-needed on some edge condition instead of incoming skb being dropped after landing in the (subflow) receive queue. Move the increment in the correct location. Fixes: ce599c51 ("mptcp: properly account bulk freed memory") Cc: stable@vger.kernel.org Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfPaolo Abeni authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: Fix a possible null-ptr-deref sometimes triggered by iptables-restore at boot time. Register iptables {ipv4,ipv6} nat table pernet in first place to fix this issue. Patch #1 and #2 from Kuniyuki Iwashima. netfilter pull request 24-07-31 * tag 'nf-24-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: iptables: Fix potential null-ptr-deref in ip6table_nat_table_init(). netfilter: iptables: Fix null-ptr-deref in iptable_nat_table_init(). ==================== Link: https://patch.msgid.link/20240731213046.6194-1-pablo@netfilter.orgSigned-off-by: -
Maciej Żenczykowski authored
The current logic only works if the PIO is between two other ND user options. This fixes it so that the PIO can also be either before or after other ND user options (for example the first or last option in the RA). side note: there's actually Android tests verifying a portion of the old broken behaviour, so: https://android-review.googlesource.com/c/kernel/tests/+/3196704 fixes those up. Cc: Jen Linkova <furry@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Patrick Rohr <prohr@google.com> Cc: David Ahern <dsahern@kernel.org> Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Maciej Żenczykowski <maze@google.com> Fixes: 048c796b ("ipv6: adjust ndisc_is_useropt() to also return true for PIO") Link: https://patch.msgid.link/20240730001748.147636-1-maze@google.comSigned-off-by:
-
Faizal Rahim authored
Following the implementation of "igc: Add TransmissionOverrun counter" patch, when a taprio command is triggered by user, igc processes two commands: TAPRIO_CMD_REPLACE followed by TAPRIO_CMD_STATS. However, both commands unconditionally pass through igc_tsn_offload_apply() which evaluates and triggers reset adapter. The double reset causes issues in the calculation of adapter->qbv_count in igc. TAPRIO_CMD_REPLACE command is expected to reset the adapter since it activates qbv. It's unexpected for TAPRIO_CMD_STATS to do the same because it doesn't configure any driver-specific TSN settings. So, the evaluation in igc_tsn_offload_apply() isn't needed for TAPRIO_CMD_STATS. To address this, commands parsing are relocated to igc_tsn_enable_qbv_scheduling(). Commands that don't require an adapter reset will exit after processing, thus avoiding igc_tsn_offload_apply(). Fixes: d3750076 ("igc: Add TransmissionOverrun counter") Signed-off-by:
Faizal Rahim <faizal.abdul.rahim@linux.intel.com> Acked-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by:
Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20240730173304.865479-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Krzysztof Kozlowski authored
To the best of my knowledge, Alex Elder is not being paid to support Qualcomm IPA networking drivers, so drop the status from "supported" to "maintained". Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by:
Alex Elder <elder@kernel.org> Link: https://patch.msgid.link/20240730104016.22103-1-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Herve Codina authored
Received frame from QMC contains the CRC. Upper layers don't need this CRC and tcpdump mentioned trailing junk data due to this CRC presence. As some other HDLC driver, simply discard this CRC. Fixes: d0f2258e ("net: wan: Add support for QMC HDLC") Cc: stable@vger.kernel.org Signed-off-by:
Herve Codina <herve.codina@bootlin.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240730063133.179598-1-herve.codina@bootlin.comSigned-off-by:
-
Herve Codina authored
The carrier_lock spinlock protects the carrier detection. While it is held, framer_get_status() is called which in turn takes a mutex. This is not correct and can lead to a deadlock. A run with PROVE_LOCKING enabled detected the issue: [ BUG: Invalid wait context ] ... c204ddbc (&framer->mutex){+.+.}-{3:3}, at: framer_get_status+0x40/0x78 other info that might help us debug this: context-{4:4} 2 locks held by ifconfig/146: #0: c0926a38 (rtnl_mutex){+.+.}-{3:3}, at: devinet_ioctl+0x12c/0x664 #1: c2006a40 (&qmc_hdlc->carrier_lock){....}-{2:2}, at: qmc_hdlc_framer_set_carrier+0x30/0x98 Avoid the spinlock usage and convert carrier_lock to a mutex. Fixes: 54762918 ("net: wan: fsl_qmc_hdlc: Add framer support") Cc: stable@vger.kernel.org Signed-off-by: -
Jakub Kicinski authored
Tariq Toukan says: ==================== mlx5 misc fixes 2024-07-30 This patchset provides misc bug fixes from the team to the mlx5 core and Eth drivers. ==================== Link: https://patch.msgid.link/20240730061638.1831002-1-tariqt@nvidia.comSigned-off-by:
-
Shahar Shitrit authored
Since the documentation for mlx5_toggle_port_link states that it should only be used after setting the port register, we add a check for the return value from mlx5_port_set_eth_ptys to ensure the register was successfully set before calling it. Fixes: 667daeda ("net/mlx5e: Toggle link only after modifying port parameters") Signed-off-by:
Shahar Shitrit <shshitrit@nvidia.com> Reviewed-by:
Carolina Jubran <cjubran@nvidia.com> Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Reviewed-by:
Wojciech Drewek <wojciech.drewek@intel.com> Link: https://patch.msgid.link/20240730061638.1831002-9-tariqt@nvidia.comSigned-off-by:
-
Chris Mi authored
The cited commit allocates a new modify header to replace the old one when updating CT entry. But if failed to allocate a new one, eg. exceed the max number firmware can support, modify header will be an error pointer that will trigger a panic when deallocating it. And the old modify header point is copied to old attr. When the old attr is freed, the old modify header is lost. Fix it by restoring the old attr to attr when failed to allocate a new modify header context. So when the CT entry is freed, the right modify header context will be freed. And the panic of accessing error pointer is also fixed. Fixes: 94ceffb4 ("net/mlx5e: Implement CT entry update") Signed-off-by:
Chris Mi <cmi@nvidia.com> Signed-off-by:
-
Rahul Rameshbabu authored
Require mlx5 classifier action support when creating IPSec chains in offload path. MLX5_IPSEC_CAP_PRIO should only be set if CONFIG_MLX5_CLS_ACT is enabled. If CONFIG_MLX5_CLS_ACT=n and MLX5_IPSEC_CAP_PRIO is set, configuring IPsec offload will fail due to the mlxx5 ipsec chain rules failing to be created due to lack of classifier action support. Fixes: fa5aa2f8 ("net/mlx5e: Use chains for IPsec policy priority offload") Signed-off-by:
Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
Moshe Shemesh authored
On sync reset reload work, when remote host updates devlink on reload actions performed on that host, it misses taking devlink lock before calling devlink_remote_reload_actions_performed() which results in triggering lock assert like the following: WARNING: CPU: 4 PID: 1164 at net/devlink/core.c:261 devl_assert_locked+0x3e/0x50 … CPU: 4 PID: 1164 Comm: kworker/u96:6 Tainted: G S W 6.10.0-rc2+ #116 Hardware name: Supermicro SYS-2028TP-DECTR/X10DRT-PT, BIOS 2.0 12/18/2015 Workqueue: mlx5_fw_reset_events mlx5_sync_reset_reload_work [mlx5_core] RIP: 0010:devl_assert_locked+0x3e/0x50 … Call Trace: <TASK> ? __warn+0xa4/0x210 ? devl_assert_locked+0x3e/0x50 ? report_bug+0x160/0x280 ? handle_bug+0x3f/0x80 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? devl_assert_locked+0x3e/0x50 devlink_notify+0x88/0x2b0 ? mlx5_attach_device+0x20c/0x230 [mlx5_core] ? __pfx_devlink_notify+0x10/0x10 ? process_one_work+0x4b6/0xbb0 process_one_work+0x4b6/0xbb0 […] Fixes: 84a433a4 ("net/mlx5: Lock mlx5 devlink reload callbacks") Signed-off-by:
Moshe Shemesh <moshe@nvidia.com> Reviewed-by:
Maor Gottlieb <maorg@nvidia.com> Signed-off-by:
-
Mark Bloch authored
The cited commit didn't change the body of the loop as it should. It shouldn't be using MLX5_LAG_P1. Fixes: 7e978e77 ("net/mlx5: Lag, use actual number of lag ports") Signed-off-by:
Mark Bloch <mbloch@nvidia.com> Signed-off-by:
-
Yevgeny Kliteynik authored
This patch reduces the size of hw_ste_arr_optimized array that is allocated on stack from 640 bytes (5 match STEs + 5 action STES) to 448 bytes (2 match STEs + 5 action STES). This fixes the 'stack guard page was hit' issue, while still fitting majority of the usecases (up to 2 match STEs). Signed-off-by:
Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by:
Alex Vesker <valex@nvidia.com> Signed-off-by:
-
Shay Drory authored
In case mlx5_irq_alloc fails, the previously allocated index remains in the XArray, which could lead to inconsistencies. Fix it by adding error handling that erases the allocated index from the XArray if mlx5_irq_alloc returns an error. Fixes: c36326d3 ("net/mlx5: Round-Robin EQs over IRQs") Signed-off-by:
Shay Drory <shayd@nvidia.com> Reviewed-by:
Maher Sanalla <msanalla@nvidia.com> Signed-off-by:
-
Shay Drory authored
There is no point in recovery during device shutdown. if health work started need to wait for it to avoid races and NULL pointer access. Hence, drain health WQ on shutdown callback. Fixes: 1958fc2f ("net/mlx5: SF, Add auxiliary device driver") Fixes: d2aa060d ("net/mlx5: Cancel health poll before sending panic teardown command") Signed-off-by:
-
Breno Leitao authored
The network maintainers need to be copied if the skbuff.h is touched. This also helps git-send-email to figure out the proper maintainers when touching the file. Signed-off-by:
Breno Leitao <leitao@debian.org> Reviewed-by:
-
Heiner Kallweit authored
The skb isn't consumed in case of NETDEV_TX_BUSY, therefore don't increment the tx_dropped counter. Fixes: 188f4af0 ("r8169: use NETDEV_TX_{BUSY/OK}") Cc: stable@vger.kernel.org Suggested-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf 2024-07-31 We've added 2 non-merge commits during the last 2 day(s) which contain a total of 2 files changed, 2 insertions(+), 2 deletions(-). The main changes are: 1) Fix BPF selftest build after tree sync with regards to a _GNU_SOURCE macro redefined compilation error, from Stanislav Fomichev. 2) Fix a wrong test in the ASSERT_OK() check in uprobe_syscall BPF selftest, from Jiri Olsa. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf/selftests: Fix ASSERT_OK condition check in uprobe_syscall test selftests/bpf: Filter out _GNU_SOURCE when compiling test_cpp ==================== Link: https://patch.msgid.link/20240731115706.19677-1-daniel@iogearbox.netSigned-off-by:
-
- 31 Jul, 2024 6 commits
-
-
Kuniyuki Iwashima authored
ip6table_nat_table_init() accesses net->gen->ptr[ip6table_nat_net_ops.id], but the function is exposed to user space before the entry is allocated via register_pernet_subsys(). Let's call register_pernet_subsys() before xt_register_template(). Fixes: fdacd57c ("netfilter: x_tables: never register tables by default") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Kuniyuki Iwashima authored
We had a report that iptables-restore sometimes triggered null-ptr-deref at boot time. [0] The problem is that iptable_nat_table_init() is exposed to user space before the kernel fully initialises netns. In the small race window, a user could call iptable_nat_table_init() that accesses net_generic(net, iptable_nat_net_id), which is available only after registering iptable_nat_net_ops. Let's call register_pernet_subsys() before xt_register_template(). [0]: bpfilter: Loaded bpfilter_umh pid 11702 Started bpfilter BUG: kernel NULL pointer dereference, address: 0000000000000013 PF: supervisor write access in kernel mode PF: error_code(0x0002) - not-present page PGD 0 P4D 0 PREEMPT SMP NOPTI CPU: 2 PID: 11879 Comm: iptables-restor Not tainted 6.1.92-99.174.amzn2023.x86_64 #1 Hardware name: Amazon EC2 c6i.4xlarge/, BIOS 1.0 10/16/2017 RIP: 0010:iptable_nat_table_init (net/ipv4/netfilter/iptable_nat.c:87 net/ipv4/netfilter/iptable_nat.c:121) iptable_nat Code: 10 4c 89 f6 48 89 ef e8 0b 19 bb ff 41 89 c4 85 c0 75 38 41 83 c7 01 49 83 c6 28 41 83 ff 04 75 dc 48 8b 44 24 08 48 8b 0c 24 <48> 89 08 4c 89 ef e8 a2 3b a2 cf 48 83 c4 10 44 89 e0 5b 5d 41 5c RSP: 0018:ffffbef902843cd0 EFLAGS: 00010246 RAX: 0000000000000013 RBX: ffff9f4b052caa20 RCX: ffff9f4b20988d80 RDX: 0000000000000000 RSI: 0000000000000064 RDI: ffffffffc04201c0 RBP: ffff9f4b29394000 R08: ffff9f4b07f77258 R09: ffff9f4b07f77240 R10: 0000000000000000 R11: ffff9f4b09635388 R12: 0000000000000000 R13: ffff9f4b1a3c6c00 R14: ffff9f4b20988e20 R15: 0000000000000004 FS: 00007f6284340000(0000) GS:ffff9f51fe280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000013 CR3: 00000001d10a6005 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? show_trace_log_lvl (arch/x86/kernel/dumpstack.c:259) ? show_trace_log_lvl (arch/x86/kernel/dumpstack.c:259) ? xt_find_table_lock (net/netfilter/x_tables.c:1259) ? __die_body.cold (arch/x86/kernel/dumpstack.c:478 arch/x86/kernel/dumpstack.c:420) ? page_fault_oops (arch/x86/mm/fault.c:727) ? exc_page_fault (./arch/x86/include/asm/irqflags.h:40 ./arch/x86/include/asm/irqflags.h:75 arch/x86/mm/fault.c:1470 arch/x86/mm/fault.c:1518) ? asm_exc_page_fault (./arch/x86/include/asm/idtentry.h:570) ? iptable_nat_table_init (net/ipv4/netfilter/iptable_nat.c:87 net/ipv4/netfilter/iptable_nat.c:121) iptable_nat xt_find_table_lock (net/netfilter/x_tables.c:1259) xt_request_find_table_lock (net/netfilter/x_tables.c:1287) get_info (net/ipv4/netfilter/ip_tables.c:965) ? security_capable (security/security.c:809 (discriminator 13)) ? ns_capable (kernel/capability.c:376 kernel/capability.c:397) ? do_ipt_get_ctl (net/ipv4/netfilter/ip_tables.c:1656) ? bpfilter_send_req (net/bpfilter/bpfilter_kern.c:52) bpfilter nf_getsockopt (net/netfilter/nf_sockopt.c:116) ip_getsockopt (net/ipv4/ip_sockglue.c:1827) __sys_getsockopt (net/socket.c:2327) __x64_sys_getsockopt (net/socket.c:2342 net/socket.c:2339 net/socket.c:2339) do_syscall_64 (arch/x86/entry/common.c:51 arch/x86/entry/common.c:81) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) RIP: 0033:0x7f62844685ee Code: 48 8b 0d 45 28 0f 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 37 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 0a c3 66 0f 1f 84 00 00 00 00 00 48 8b 15 09 RSP: 002b:00007ffd1f83d638 EFLAGS: 00000246 ORIG_RAX: 0000000000000037 RAX: ffffffffffffffda RBX: 00007ffd1f83d680 RCX: 00007f62844685ee RDX: 0000000000000040 RSI: 0000000000000000 RDI: 0000000000000004 RBP: 0000000000000004 R08: 00007ffd1f83d670 R09: 0000558798ffa2a0 R10: 00007ffd1f83d680 R11: 0000000000000246 R12: 00007ffd1f83e3b2 R13: 00007f628455baa0 R14: 00007ffd1f83d7b0 R15: 00007f628457a008 </TASK> Modules linked in: iptable_nat(+) bpfilter rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache veth xt_state xt_connmark xt_nat xt_statistic xt_MASQUERADE xt_mark xt_addrtype ipt_REJECT nf_reject_ipv4 nft_chain_nat nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_comment nft_compat nf_tables nfnetlink overlay nls_ascii nls_cp437 vfat fat ghash_clmulni_intel aesni_intel ena crypto_simd ptp cryptd i8042 pps_core serio button sunrpc sch_fq_codel configfs loop dm_mod fuse dax dmi_sysfs crc32_pclmul crc32c_intel efivarfs CR2: 0000000000000013 Fixes: fdacd57c ("netfilter: x_tables: never register tables by default") Reported-by:
Takahiro Kawahara <takawaha@amazon.co.jp> Signed-off-by:
-
Linus Torvalds authored
David Laight pointed out that we should deal with the min3() and max3() mess too, which still does excessive expansion. And our current macros are actually rather broken. In particular, the macros did this: #define min3(x, y, z) min((typeof(x))min(x, y), z) #define max3(x, y, z) max((typeof(x))max(x, y), z) and that not only is a nested expansion of possibly very complex arguments with all that involves, the typing with that "typeof()" cast is completely wrong. For example, imagine what happens in max3() if 'x' happens to be a 'unsigned char', but 'y' and 'z' are 'unsigned long'. The types are compatible, and there's no warning - but the result is just random garbage. No, I don't think we've ever hit that issue in practice, but since we now have sane infrastructure for doing this right, let's just use it. It fixes any excessive expansion, and also avoids these kinds of broken type issues. Requested-by:
David Laight <David.Laight@aculab.com> Acked-by:
Arnd Bergmann <arnd@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: - fix regression in extent map rework when handling insertion of overlapping compressed extent - fix unexpected file length when appending to a file using direct io and buffer not faulted in - in zoned mode, fix accounting of unusable space when flipping read-only block group back to read-write - fix page locking when COWing an inline range, assertion failure found by syzbot - fix calculation of space info in debugging print - tree-checker, add validation of data reference item - fix a few -Wmaybe-uninitialized build warnings * tag 'for-6.11-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: initialize location to fix -Wmaybe-uninitialized in btrfs_lookup_dentry() btrfs: fix corruption after buffer fault in during direct IO append write btrfs: zoned: fix zone_unusable accounting on making block group read-write again btrfs: do not subtract delalloc from avail bytes btrfs: make cow_file_range_inline() honor locked_page on error btrfs: fix corrupt read due to bad offset of a compressed extent map btrfs: tree-checker: validate dref root and objectid
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v6.11-2024-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools Pull perf tools fixes from Namhyung Kim: "Some more build fixes and a random crash fix: - Fix cross-build by setting pkg-config env according to the arch - Fix static build for missing library dependencies - Fix Segfault when callchain has no symbols" * tag 'perf-tools-fixes-for-v6.11-2024-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: perf docs: Document cross compilation perf: build: Link lib 'zstd' for static build perf: build: Link lib 'lzma' for static build perf: build: Only link libebl.a for old libdw perf: build: Set Python configuration for cross compilation perf: build: Setup PKG_CONFIG_LIBDIR for cross compilation perf tool: fix dereferencing NULL al->maps
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== ice: fix AF_XDP ZC timeout and concurrency issues Maciej Fijalkowski says: Changes included in this patchset address an issue that customer has been facing when AF_XDP ZC Tx sockets were used in combination with flow control and regular Tx traffic. After executing: ethtool --set-priv-flags $dev link-down-on-close on ethtool -A $dev rx on tx on launching multiple ZC Tx sockets on $dev + pinging remote interface (so that regular Tx traffic is present) and then going through down/up of $dev, Tx timeout occurred and then most of the time ice driver was unable to recover from that state. These patches combined together solve the described above issue on customer side. Main focus here is to forbid producing Tx descriptors when either carrier is not yet initialized or process of bringing interface down has already started. v1: https://lore.kernel.org/netdev/20240708221416.625850-1-anthony.l.nguyen@intel.com/ * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: xsk: fix txq interrupt mapping ice: add missing WRITE_ONCE when clearing ice_rx_ring::xdp_prog ice: improve updating ice_{t,r}x_ring::xsk_pool ice: toggle netif_carrier when setting up XSK pool ice: modify error handling when setting XSK pool in ndo_bpf ice: replace synchronize_rcu with synchronize_net ice: don't busy wait for Rx queue disable in ice_qp_dis() ice: respect netif readiness in AF_XDP ZC related ndo's ==================== Link: https://patch.msgid.link/20240729200716.681496-1-anthony.l.nguyen@intel.comSigned-off-by:
-
