Skip to content

L
linux
Switch branch/tag
  1. 23 Sep, 2015 5 commits
    • Neil Armstrong's avatar
      net: dsa: Fix Marvell Egress Trailer check · fbd03513
      Neil Armstrong authored 
      The Marvell Egress rx trailer check must be fixed to
correctly detect bad bits in the third byte of the
Eggress trailer as described in the Table 28 of the
88E6060 datasheet.
The current code incorrectly omits to check the third
byte and checks the fourth byte twice.
Signed-off-by: default avatarNeil Armstrong <narmstrong@baylibre.com>
Acked-by: default avatarGuenter Roeck <linux@roeck-us.net>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      fbd03513
    • Dmitriy Vyukov's avatar
      lib: fix data race in rhashtable_rehash_one · 7def0f95
      Dmitriy Vyukov authored 
      rhashtable_rehash_one() uses complex logic to update entry->next field,
after INIT_RHT_NULLS_HEAD and NULLS_MARKER expansion:

entry->next = 1 | ((base + off) << 1)

This can be compiled along the lines of:

entry->next = base + off
entry->next <<= 1
entry->next |= 1

Which will break concurrent readers.

NULLS value recomputation is not needed here, so just remove
the complex logic.

The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: default avatarDmitry Vyukov <dvyukov@google.com>
Acked-by: default avatarEric Dumazet <edumazet@google.com>
Acked-by: default avatarThomas Graf <tgraf@suug.ch>
Acked-by: default avatarHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7def0f95
    • Tobias Klauser's avatar
      ch9200: Convert to use module_usb_driver · 23eedbc2
      Tobias Klauser authored 
      Converts the ch9200 driver to use the module_usb_driver() macro which
makes the code smaller and a bit simpler.
Signed-off-by: default avatarTobias Klauser <tklauser@distanz.ch>
Acked-by: default avatarMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      23eedbc2
    • Jesse Gross's avatar
      openvswitch: Zero flows on allocation. · ae5f2fb1
      Jesse Gross authored 
      When support for megaflows was introduced, OVS needed to start
installing flows with a mask applied to them. Since masking is an
expensive operation, OVS also had an optimization that would only
take the parts of the flow keys that were covered by a non-zero
mask. The values stored in the remaining pieces should not matter
because they are masked out.

While this works fine for the purposes of matching (which must always
look at the mask), serialization to netlink can be problematic. Since
the flow and the mask are serialized separately, the uninitialized
portions of the flow can be encoded with whatever values happen to be
present.

In terms of functionality, this has little effect since these fields
will be masked out by definition. However, it leaks kernel memory to
userspace, which is a potential security vulnerability. It is also
possible that other code paths could look at the masked key and get
uninitialized data, although this does not currently appear to be an
issue in practice.

This removes the mask optimization for flows that are being installed.
This was always intended to be the case as the mask optimizations were
really targetting per-packet flow operations.

Fixes: 03f0d916 ("openvswitch: Mega flow implementation")
Signed-off-by: default avatarJesse Gross <jesse@nicira.com>
Acked-by: default avatarPravin B Shelar <pshelar@nicira.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ae5f2fb1
    • Russell King's avatar
      net: dsa: actually force the speed on the CPU port · 53adc9e8
      Russell King authored 
      Commit 54d792f2 ("net: dsa: Centralise global and port setup
code into mv88e6xxx.") merged in the 4.2 merge window broke the link
speed forcing for the CPU port of Marvell DSA switches.  The original
code was:

        /* MAC Forcing register: don't force link, speed, duplex
         * or flow control state to any particular values on physical
         * ports, but force the CPU port and all DSA ports to 1000 Mb/s
         * full duplex.
         */
        if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
                REG_WRITE(addr, 0x01, 0x003e);
        else
                REG_WRITE(addr, 0x01, 0x0003);

but the new code does a read-modify-write:

                reg = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
                if (dsa_is_cpu_port(ds, port) ||
                    ds->dsa_port_mask & (1 << port)) {
                        reg |= PORT_PCS_CTRL_FORCE_LINK |
                                PORT_PCS_CTRL_LINK_UP |
                                PORT_PCS_CTRL_DUPLEX_FULL |
                                PORT_PCS_CTRL_FORCE_DUPLEX;
                        if (mv88e6xxx_6065_family(ds))
                                reg |= PORT_PCS_CTRL_100;
                        else
                                reg |= PORT_PCS_CTRL_1000;

The link speed in the PCS control register is a two bit field.  Forcing
the link speed in this way doesn't ensure that the bit field is set to
the correct value - on the hardware I have here, the speed bitfield
remains set to 0x03, resulting in the speed not being forced to gigabit.

We must clear both bits before forcing the link speed.

Fixes: 54d792f2 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      53adc9e8
  3. 22 Sep, 2015 1 commit
  5. 21 Sep, 2015 25 commits
  7. 18 Sep, 2015 9 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7