- 16 Sep, 2014 40 commits
-
-
Sumit.Saxena@avagotech.com authored
Resending the patch. Addressed the review comments from Tomas Henzl. Move buff_offset inside spinlock, corrected loop at crash dump buffer free, reset_devices check is added to disable fw crash dump feature in kdump kernel. This feature will provide similar interface as kernel crash dump feature. When megaraid firmware encounter any crash, driver will collect the firmware raw image and dump it into pre-configured location. Driver will allocate two different segment of memory. #1 Non-DMA able large buffer (will be allocated on demand) to capture actual FW crash dump. #2 DMA buffer (persistence allocation) just to do a arbitrator job. Firmware will keep writing Crash dump data in chucks of DMA buffer size into #2, which will be copy back by driver to the host memory as described in #1. Driver-Firmware interface: ================== A.) Host driver can allocate maximum 512MB Host memory to store crash dump data. This memory will be internal to the host and will not be exposed to the Firmware. Driver may not be able to allocate 512 MB. In that case, driver will do possible memory (available at run time) allocation to store crash dump data. Let’s call this buffer as Host Crash Buffer. Host Crash buffer will not be contigious as a whole, but it will have multiple chunk of contigious memory. This will be internal to driver and firmware/application are unaware of it. Partial allocation of Host Crash buffer may have valid information to debug depending upon what was collected in that buffer and depending on nature of failure. Complete Crash dump is the best case, but we do want to capture partial buffer just to grab something rather than nothing. Host Crash buffer will be allocated only when FW Crash dump data is available, and will be deallocated once application copy Host Crash buffer to the file. Host Crash buffer size can be anything between 1MB to 512MB. (It will be multiple of 1MBs) B.) Irrespective of underlying Firmware capability of crash dump support, driver will allocate DMA buffer at start of the day for each MR controllers. Let’s call this buffer as “DMA Crash Buffer”. For this feature, size of DMA crash buffer will be 1MB. (We will not gain much even if DMA buffer size is increased.) C.) Driver will now read Controller Info sending existing dcmd “MR_DCMD_CTRL_GET_INFO”. Driver should extract the information from ctrl info provided by firmware and figure out if firmware support crash dump feature or not. Driver will enable crash dump feature only if “Firmware support Crash dump” + “Driver was able to create DMA Crash Buffer”. If either one from above is not set, Crash dump feature should be disable in driver. Firmware will enable crash dump feature only if “Driver Send DCMD- MR_DCMD_SET_CRASH_BUF_PARA with MR_CRASH_BUF_TURN_ON” Helper application/script should use sysfs parameter fw_crash_xxx to actually copy data from host memory to the filesystem. Signed-off-by:
Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by:
Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Sumit.Saxena@avagotech.com authored
Resending the patch. Addressed the review comments from Tomas Henzl. Current driver updates reply post host index to let firmware know that replies are processed, while returning from ISR function, only if there is no oustanding replies in reply queue. Driver will free the request frame immediately from ISR but reply post host index is not yet updated. It means freed request can be used by submission path and there may be a tight loop in request/reply path. In such condition, firmware may crash when it tries to post reply and there is no free reply post descriptor. Eventually two things needs to be change to avoid this issue. Increase reply queue depth (double than request queue) to accommodate worst case scenario. Update reply post host index to firmware once it reach to some pre-defined threshold value. This change will make sure that firmware will always have some buffer of reply descriptor and will never find empty reply descriptor in completion path. Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
Resending the patch. Addressed the review comments from Tomas Henzl. Reduce the assingment for u64 req_data variable. Use writeq() for 64bit PCI write instead of writel() to avoid additional lock overhead. Signed-off-by:
-
Sumit.Saxena@avagotech.com authored
Resending the patch. Addressed the review comments from Tomas Henzl. Current driver allow device scan for all the devices on channel 0 and 1. E.a If we have two single drive raid volumes, we may see prints like below. First two prints are for physical device which are used to form VD. Prints like this creates confusion as it is really not required to scan any hidden physical devices. scsi1 : LSI SAS based MegaRAID driver scsi 1:0:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 scsi 1:0:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 When slave_alloc called, sdev-type will not be set, so current code will always return "0" in slave_alloc callback. This patch make sure that driver return "-ENXIO" for non-syspd devices. After this patch, we will see prints in syslog only for devices which are exposed. For current example, below print will be available in syslog. scsi1 : LSI SAS based MegaRAID driver scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5 Signed-off-by:
-
Sreekanth Reddy authored
In _scsih_probe, propagate the return value from scsi_add_host. In mpt3sas, avoid calling list_del twice if that returns an error, which causes list_del corruption warnings if an error is returned. Tested with blk-mq and scsi-mq patches to properly cleanup from and propagate blk_mq_init_rq_map errors. Signed-off-by:
Robert Elliott <elliott@hp.com> Acked-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt3sas driver version to 04.100.00.00. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Sreekanth Reddy authored
Up to now, Driver allocates a single contiguous block of memory pool for all reply queues and passes down a single address in the ReplyDescriptorPostQueueAddress field of the IOC Init Request Message to the firmware. When firmware receives this address, it will program each of the Reply Descriptor Post Queue registers, as each reply queue has its own register. Thus the firmware, starting from a base address it determines the starting address of the subsequent reply queues through some simple arithmetic calculations. The size of this contiguous block of memory pool is directly proportional to number of MSI-X vectors and the HBA queue depth. For example higher MSIX vectors requires larger contiguous block of memory pool. But some of the OS kernels are unable to allocate this larger contiguous block of memory pool. So, the proposal is to allocate memory independently for each Reply Queue and pass down all of the addresses to the firmware. Then the firmware will just take each address and program the value into the correct register. When HBAs with older firmware(i.e. without RDPQ capability) is used with this new driver then the max_msix_vectors value would be set to 8 by default. Change set in v1: 1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file instead of moving all these functions before mpt3sas_base_map_resources() function a. _base_wait_for_doorbell_int() b. _base_wait_for_doorbell_ack() c. _base_wait_for_doorbell_not_used() d. _base_handshake_req_reply_wait() e. _base_get_ioc_facts() 2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask. This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same. 3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions a. _base_release_memory_pools() b. _base_allocate_memory_pools() c. _base_send_ioc_init() d. _base_make_ioc_operational() Signed-off-by: -
Sreekanth Reddy authored
Added following branding Strings for Intel custom HBAs support. Driver String: Vendor ID Device ID SubSystemVendor ID SubSystemDevice ID Intel(R) Integrated RAID Module RMS3JC080 0x1000 0x0097 0x8086 0x3521 Intel(R) RAID Controller RS3GC008 0x1000 0x0097 0x8086 0x3522 Intel(R) RAID Controller RS3FC044 0x1000 0x0097 0x8086 0x3523 Intel(R) RAID Controller RS3UC080 0x1000 0x0097 0x8086 0x3524 Signed-off-by:
-
Sreekanth Reddy authored
Copyright in driver sources is updated for year the 2014. Signed-off-by:
-
Sreekanth Reddy authored
Below is the change set in MPI2.5 Rev H specification and 2.00.32 header files 1) Added reserved fields to IO Unit Page 7 for future use. 2) Added optional functionality to IOCInit Request so that the host may specify a separate base address for each Reply Descriptor Post Queue. IOC support for this is indicated using a new IOCCapabilities bit in the IOCFacts Reply. 3) Added Toolbox Console Text Display Tool The host uses the Console Text Display Tool to send a string to IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal). 4) Firmware images can now be signed using an encrypted hash. 5) Added MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL 6) Added more details about configuration page restrictions when Host Based Discovery is enabled Enabling host based discovery affects the availability of some configuration pages and events. The SAS Expander, SAS Device, and SAS Enclosure configuration pages are not available from the IOC. The IOC returns an error status to any Configuration Request message attempting to access these pages. The IOC does not send the SAS Discovery Event, the SAS Topology Change List Event, or the SAS Enclosure Device Status Change Event when host based discovery is enabled. 7) Bit 13 of the SAS IO Unit Page 1 ControlFlags field is now obsolete. It was used to enable limiting direct attached SATA maximum link rate to 1.5 Gbps. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt3sas driver version to 03.100.00.00. Signed-off-by:
-
Sreekanth Reddy authored
Added code to send an SEP message that turns off the Predictive Failure LED when a drive is removed (if Predictive Failure LED was turned on). Added a new flag 'pfa_led_on' per device that tracks the status of Predictive Failure LED. When the drive is removed, this flag is checked and sends an SEP message to turn off the respective Predictive Failure LED. Signed-off-by:
-
Sreekanth Reddy authored
Below is the change set in MPI2.5 Rev G specification and 2.00.31 header files 1) Added SCSIStatusQualifier to SCSI IO Error Reply message. 2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field. 3) Added Allow Protection Information bit for IR Volume Create. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt2sas driver version to 18.100.00.00. Signed-off-by:
-
Sreekanth Reddy authored
mpt2sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state. Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state. This patch will make sure that 1.Driver to send IOC facts request message only if HBA is in operational or ready state. 2.If IOC is in fault state, a diagnostic reset would be issued. 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state. If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver. Signed-off-by:
-
Sreekanth Reddy authored
Up to now, Driver allocates a single contiguous block of memory pool for all reply queues and passes down a single address in the ReplyDescriptorPostQueueAddress field of the IOC Init Request Message to the firmware. When firmware receives this address, it will program each of the Reply Descriptor Post Queue registers, as each reply queue has its own register. Thus the firmware, starting from a base address it determines the starting address of the subsequent reply queues through some simple arithmetic calculations. The size of this contiguous block of memory pool is directly proportional to number of MSI-X vectors and the HBA queue depth. For example higher MSIX vectors requires larger contiguous block of memory pool. But some of the OS kernels are unable to allocate this larger contiguous block of memory pool. So, the proposal is to allocate memory independently for each Reply Queue and pass down all of the addresses to the firmware. Then the firmware will just take each address and program the value into the correct register. When HBAs with older firmware(i.e. without RDPQ capability) is used with this new driver then the max_msix_vectors value would be set to 8 by default. Change_set in v1: 1. Declared _base_get_ioc_facts() function at the beginning of the mpt2sas_base.c file instead of moving all these functions before mpt2sas_base_map_resources() function a. _base_wait_for_doorbell_int() b. _base_wait_for_doorbell_ack() c. _base_wait_for_doorbell_not_used() d. _base_handshake_req_reply_wait() e. _base_get_ioc_facts() 2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask. This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same. 3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions a. _base_release_memory_pools() b. _base_allocate_memory_pools() c. _base_send_ioc_init() d. _base_make_ioc_operational() Signed-off-by: -
Sreekanth Reddy authored
A type casting error caused the max volume LBA to be truncated from 64 to 32 bits. The virtual LBA would also get truncated to 32 bits in the case of a 16-byte READ/WRITE command. Rewrite entire function to get rid of code duplication and type casts. Use get/put_unaligned wrappers to extract and replace the LBA field in the MPI request CDB. Signed-off-by:
-
Sreekanth Reddy authored
Bump mpt2sas driver version to 17.100.00.00 Signed-off-by:
-
Sreekanth Reddy authored
Added code to send a SEP message that turns off the Predictive Failure LED when a drive is removed (if Predictive Failure LED was turned on). Added a new flag 'pfa_led_on' per device that tracks the status of Predictive Failure LED. When the drive is removed, this flag is checked and sends the SEP message to turn off the respective Predictive Failure LED. Signed-off-by:
-
Sreekanth Reddy authored
Copyright in driver sources is updated for year the 2014. Signed-off-by:
-
Sreekanth Reddy authored
Below is the change set in MPI2 Rev Y specification and in 2.00.17 header files 1) Added SCSIStatusQualifier to SCSI IO Error Reply message. 2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field. Below is the change set in MPI2 Rev Z specification and in 2.00.19 header files 1) Added reserved fields to IO Unit Page 7 for future use. 2) Added optional functionality to IOCInit Request so that the host may specify a separate base address for each Reply Descriptor Post Queue. IOC support for this is indicated using a new IOCCapabilities bit in the IOCFacts Reply. 3) Added Toolbox Console Text Display Tool The host uses the Console Text Display Tool to send a string to IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal). The copyright in the mpi files is updated for year 2014 Signed-off-by:
-
Sreekanth Reddy authored
Added driver module parameter max_msix_vectors. Using this module parameter the maximum number of MSI-X vectors could be set. The number of MSI-X vectors used would be the minimum of MSI-X vectors supported by the HBA, the number of CPU cores and the value set to max_msix_vectors module parameters. Signed-off-by:
-
Tej Parkash authored
Signed-off-by:
Tej Parkash <tej.parkash@qlogic.com> Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Eddie Wai <eddie.wai@broadcom.com> Signed-off-by:
-
Chad Dupuis authored
This patch is based on a problem and solution from Maurizio Lombardi where bnx2fc isn't consistent in which device struct we using for DMA map and unmap operations. Make them consistent by using dma_sg_unmap in bnx2fc_unmap_sg_list like bnx2fc_map_sg. Reviewed-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
James Smart authored
Update lpfc version to driver version 10.4.8000.0 Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
Dick Kennedy <dick.kennedy@emulex.com> Signed-off-by:
-
James Smart authored
Fix for handling unmapped ndlp in target reset handler Signed-off-by:
-
James Smart authored
Fixed Low priority issues from lpfc given by fortify source code scan. Signed-off-by:
-
James Smart authored
Fixed High priority issues from lpfc given by fortify source code scan. Signed-off-by:
-
James Smart authored
Fix crash from page fault caused by use after rport delete. Signed-off-by:
-
James Smart authored
Fix locking issues with abort data paths Signed-off-by:
-
James Smart authored
Fix race between LOGO/PLOGI handling causing NULL pointer Signed-off-by:
-
James Smart authored
Fix IP Reset processing - wait for RDY before proceeding Signed-off-by:
-
James Smart authored
Fix quarantined XRI recovery qualifier state in link bounce Signed-off-by:
-
James Smart authored
Fix discovery timeout during nameserver login Signed-off-by:
-
Alexander Gordeev authored
As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() or pci_enable_msi_exact() and pci_enable_msix_range() or pci_enable_msix_exact() interfaces. Signed-off-by:
Alexander Gordeev <agordeev@redhat.com> Reviewed-by:
-
Daniel Borkmann authored
In prandom we have already reseeding mechanisms that trigger periodically from a much better entropy source than just feeding in jiffies through lpfc_mbx_cmpl_fcf_scan_read_fcf_rec() [what a function name 8-)]. Therefore, just remove this. Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Reviewed-by:
-
Manuel Schölling authored
To be future-proof and for better readability the time comparisons are modified to use time_after() instead of plain, error-prone math. Signed-off-by:
Manuel Schölling <manuel.schoelling@gmx.de> Reviewed-by:
-
Joe Perches authored
Use the zeroing function instead of dma_alloc_coherent & memset(,0,) Signed-off-by:
Joe Perches <joe@perches.com> Reviewed-by:
-
Rashika Kheria authored
[PATCH 26/55] scsi: Mark function as static in lpfc/lpfc_bsg.c Mark function as static in lpfc/lpfc_bsg.c because it is not used outside this file. This eliminates the following warning in lpfc/lpfc_bsg.c: drivers/scsi/lpfc/lpfc_bsg.c:3348:1: warning: no previous prototype for ‘lpfc_bsg_issue_mbox_cmpl’ [-Wmissing-prototypes] Signed-off-by:
Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Reviewed-by:
-
Rashika Kheria authored
Mark functions as static in lpfc/lpfc_scsi.c because they are not used outside this file. This eliminates the following warnings in lpfc/lpfc_scsi.c: drivers/scsi/lpfc/lpfc_scsi.c:299:1: warning: no previous prototype for ‘lpfc_change_queue_depth’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:795:1: warning: no previous prototype for ‘lpfc_sli4_post_scsi_sgl_list’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3019:1: warning: no previous prototype for ‘lpfc_bg_crc’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3035:1: warning: no previous prototype for ‘lpfc_bg_csum’ [-Wmissing-prototypes] drivers/scsi/lpfc/lpfc_scsi.c:3048:1: warning: no previous prototype for ‘lpfc_calc_bg_err’ [-Wmissing-prototypes] Signed-off-by:
-
