Increase the maximal remain on channel time as longer remain
on channel requests are handled by the FW using fragmented
time events.

This reduces the number of user/kernel space iterations during
flows such as p2p_listen. In addition it is currently required
for flows which require longer duration such as p2p_sd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The RF-kill wakeup trigger flag is set in the wrong command,
which means it won't work. Also fix the comment in the TCP
wakeup trigger code -- the firmware was changed to look at
all the different trigger flags.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We should disable MIMO only if bt_traffic_load goes up to 3.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is the right source of information for the valid Tx
antennas, not the NVM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This data should taken from TLVs and not from the NVM. This
is true for the value written in CSR_HW_IF_CONFIG_REG too.

Also, no need to set the CSR_HW_IF_CONFIG_REG_BIT_MAC_SI bit
for 7000 devices which are the only devices currently
supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In firmware "listener" (monitor) mode, we still need to
open up the filters with the filter flags to receive all
frames.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This has valuable data about RFkill state seen from the fw
side.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

5ghz_disable has no effect any longer, that was changed during
refactoring of EEPROM reading/parsing. Remove it, wpa_supplicant
allow now to specify frequencies, on which device will operate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

1. Quota for the monitor interface should be added only if there is
   a channel context assigned to the interface.
2. In the unassign channel context flow, need to remove the quota
   for the monitor interface binding, before unbinding.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Andrei Epure <epure.andrei@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This feature is not implemented yet in firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The masks were wrong. They should be 0xffffffff when SCO,
HID or SNIFF profiles are used. They should be 0xffff0000
in any other case (default) to get a bit more throughput
when the BT profile allows for it.

Fix a debug print on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Mostly for debugging purposes
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In AP mode, don't attempt to program GTKs into the
device, they're used for TX only so not needed and
programming them causes error messages. Also, in
this case and if key programming fails, avoid trying
to remove the key that isn't present later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The code removed in this patch was used for bring up on
older NICs. No MVM capable fw will ever be released for
older NICs, so remove that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_IQCalibration()

DPO_RT5572_LinuxSTA_2.6.1.3_20121022/cips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable support to 5592 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
TXWI_STRUC
RXWI_STRUC

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/include/chip/rtmp_mac.h
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipAGCAdjust()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_RTMPAGCInit()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
AsicBBPWriteWithRxChain()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rtmp_chip.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This makes order of initialization of various registers similar like
on vendor driver.

Based on:
NICInitializeAsic()
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chip/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
GetIQCalibration()
IQCalibration()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rtmp_chip.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
InitFrequencyCalibrationMode()
RT5592_ChipCap

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/frq_cal.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592LoadRFNormalModeSetup()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
NICInitRT5592RFRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
NICInitRT5592RFRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
NICInitRT5592RFRegisters()
RF5592Reg_2G_5G[]

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

This patch also merge common frequency adjustment (RF_R17 settings)
code. Further work is needed, to setup more RF/BBP/MAC registers after
that.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add BBP registers initialization common with other chipsets, but for now
performed only for 5592.

Based on:
NICInitBBP()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
NICInitRT5592BbpRegisters()
NICInitBBP()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
NICInitRT5592MacRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

On vendor driver we do not initialize TX_SW_CFG{1,2}. However the same
difference is between rt2x00 and vendor driver for 5390 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>