For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a chip wide value and the PFs already report it.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.

The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We're already protected by RTNL lock, so nothing can happen to bond/its
slaves, and thus the locking is useless here (both bond->lock and
bond->curr_active_slave).

Also, add ASSERT_RTNL() both to bond_set_rx_mode() and bond_hw_addr_swap()
to catch possible uses of it without RTNL locking.

This patch also saves us from a lockdep false-positive in
bond_set_rx_mode() vs bond_hw_addr_swap().

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As dst_cookie is used in fast path sctp_transport_dst_check.

Before:
struct sctp_transport {
	struct list_head           transports;           /*     0    16 */
	atomic_t                   refcnt;               /*    16     4 */
	__u32                      dead:1;               /*    20:31  4 */
	__u32                      rto_pending:1;        /*    20:30  4 */
	__u32                      hb_sent:1;            /*    20:29  4 */
	__u32                      pmtu_pending:1;       /*    20:28  4 */

	/* XXX 28 bits hole, try to pack */

	__u32                      sack_generation;      /*    24     4 */

	/* XXX 4 bytes hole, try to pack */

	struct flowi               fl;                   /*    32    64 */
	/* --- cacheline 1 boundary (64 bytes) was 32 bytes ago --- */
	union sctp_addr            ipaddr;               /*    96    28 */

After:
struct sctp_transport {
	struct list_head           transports;           /*     0    16 */
	atomic_t                   refcnt;               /*    16     4 */
	__u32                      dead:1;               /*    20:31  4 */
	__u32                      rto_pending:1;        /*    20:30  4 */
	__u32                      hb_sent:1;            /*    20:29  4 */
	__u32                      pmtu_pending:1;       /*    20:28  4 */

	/* XXX 28 bits hole, try to pack */

	__u32                      sack_generation;      /*    24     4 */
	u32                        dst_cookie;           /*    28     4 */
	struct flowi               fl;                   /*    32    64 */
	/* --- cacheline 1 boundary (64 bytes) was 32 bytes ago --- */
	union sctp_addr            ipaddr;               /*    96    28 */
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we use a lot of time comparison math for arp_interval
comparisons, which are sometimes quite hard to read and understand.

All the time comparisons have one pattern:
(time - arp_interval_jiffies) <= jiffies <= (time + mod *
arp_interval_jiffies + arp_interval_jiffies/2)

Introduce a new helper - bond_time_in_interval(), which will do the math in
one place and, thus, will clean up the logical code. This helper introduces
a bit of overhead (by always calculating the jiffies from arp_interval),
however it's really not visible, considering that functions using it
usually run once in arp_interval milliseconds.

There are several lines slightly over 80 chars, however breaking them would
result in more hard-to-read code than several character after the 80 mark.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simple cleanup to not call slave_last_rx() on every time function. It won't
give any measurable boost - but looks cleaner and easier to understand.

There are no time-consuming functions in between these calls, so it's safe
to call it in the beginning only once.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing unlock before return from function tile_net_open()
in the error handling case.

Introduced by commit f3286a3a.
(tile: support multiple mPIPE shims in tilegx network driver)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/micrel/ks8842.c:708:6: warning: symbol 'ks8842_handle_rx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:718:6: warning: symbol 'ks8842_handle_tx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:727:6: warning: symbol 'ks8842_handle_rx_overrun' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:735:6: warning: symbol 'ks8842_tasklet' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8851_mll.c:691:6: warning: symbol 'ks_enable_qmu' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/emulex/benet/be_main.c:475:6: warning: symbol 'populate_erx_stats' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:1485:6: warning: symbol 'be_rx_compl_process_gro' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:2262:5: warning: symbol 'be_poll' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3223:6: warning: symbol 'flash_cookie' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3280:27: warning: symbol 'get_fsec_info' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1013:5: warning: symbol 'be_cmd_mccq_ext_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1071:5: warning: symbol 'be_cmd_mccq_org_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3166:5: warning: symbol 'be_cmd_get_profile_config_mbox' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3194:5: warning: symbol 'be_cmd_get_profile_config_mccq' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_roce.c:96:6: warning: symbol '_be_roce_dev_remove' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:113:6: warning: symbol '_be_roce_dev_open' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:129:6: warning: symbol '_be_roce_dev_close' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna_rx_sm_stop_wait_entry(), bna_rx_sm_rxf_stop_wait_entry(),
bna_rx_sm_started_entry(), bna_rx_sm_cleanup_wait_entry(),
and bna_rx_sm_cleanup_wait() are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1423:1: warning: symbol 'bna_rx_sm_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1476:1: warning: symbol 'bna_rx_sm_rxf_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1532:1: warning: symbol 'bna_rx_sm_started_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1597:1: warning: symbol 'bna_rx_sm_cleanup_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1602:1: warning: symbol 'bna_rx_sm_cleanup_wait' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vxlan remote list is protected by RCU and guaranteed to be non-empty.
Split out the rcu and non-rcu access to the list to fix warning
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of RCU here with out marked pointer and function doesn't match prototype
with sparse.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ax88179_tx_fixup() has quite complex code trying to push 8 bytes
of control data (len/mss), but fails to do it properly for TCP packets,
incurring an extra copy and point of memory allocation failure.

Lets use the simple and approved way.

dev->needed_headroom being 8, all frames should have 8 bytes of
headroom, so the extra copy should be unlikely anyway.

This patch should improve performance for TCP xmits.
Reported-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge net into net-next to setup some infrastructure Eric
Dumazet needs for usbnet changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Don't ignore user initiated wireless regulatory settings on cards
    with custom regulatory domains, from Arik Nemtsov.

 2) Fix length check of bluetooth information responses, from Jaganath
    Kanakkassery.

 3) Fix misuse of PTR_ERR in btusb, from Adam Lee.

 4) Handle rfkill properly while iwlwifi devices are offline, from
    Emmanuel Grumbach.

 5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.

 6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.

 7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.

 8) Fix bridge multicast code to not snoop when no querier exists,
    otherwise mutlicast traffic is lost.  From Linus Lüssing.

 9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.

10) Fix races in automatic address asignment on ipv6, which can result
    in incorrect lifetime assignments.  From Jiri Benc.

11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
    it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
    original naming of this feature.  From Cong Wang.

12) Fix crash in TIPC when server socket creation fails, from Ying Xue.

13) macvlan_changelink() silently succeeds when it shouldn't, from
    Michael S Tsirkin.

14) HTB packet scheduler can crash due to sign extension, fix from
    Stephen Hemminger.

15) With the cable unplugged, r8169 prints out a message every 10
    seconds, make it netif_dbg() instead of netif_warn().  From Peter
    Wu.

16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.

17) sis900 gets spurious TX queue timeouts due to mismanagement of link
    carrier state, from Denis Kirjanov.

18) Validate somaxconn sysctl to make sure it fits inside of a u16.
    From Roman Gushchin.

19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
  qlcnic: Fix for flash update failure on 83xx adapter
  qlcnic: Fix link speed and duplex display for 83xx adapter
  qlcnic: Fix link speed display for 82xx adapter
  qlcnic: Fix external loopback test.
  qlcnic: Removed adapter series name from warning messages.
  qlcnic: Free up memory in error path.
  qlcnic: Fix ingress MAC learning
  qlcnic: Fix MAC address filter issue on 82xx adapter
  net: ethernet: davinci_emac: drop IRQF_DISABLED
  netlabel: use domain based selectors when address based selectors are not available
  net: check net.core.somaxconn sysctl values
  sis900: Fix the tx queue timeout issue
  net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
  r8169: remove "PHY reset until link up" log spam
  net: ethernet: cpsw: drop IRQF_DISABLED
  htb: fix sign extension bug
  macvlan: handle set_promiscuity failures
  macvlan: better mode validation
  tipc: fix oops when creating server socket fails
  net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
  ...

Flash update routine was improperly checking register read API return value.
Modify register read API and perform proper error check.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Set link speed and duplex to unknown when link is not up.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Do not obtain link speed from register when adapter
  link is down.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver was not handling external loopback diagnostic
test request.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Delete MAC address from the adapter's filter table
  if the source MAC address of ingress packet matches.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move refcnt, pref, suppress_ifgroup, suppress_prefixlen out of first
cache line, as they are not used in fast path.

Make sure ctarget & fr_net are in first cache line.

(Assuming 64 bit arches and 64 bytes cache lines)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull nfsd bugfixes from Bruce Fields:
 "Most of this is due to a screwup on my part -- some gss-proxy crashes
  got fixed before the merge window but somehow never made it out of a
  temporary git repo on my laptop...."

* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
  svcrpc: set cr_gss_mech from gss-proxy as well as legacy upcall
  svcrpc: fix kfree oops in gss-proxy code
  svcrpc: fix gss-proxy xdr decoding oops
  svcrpc: fix gss_rpc_upcall create error
  NFSD/sunrpc: avoid deadlock on TCP connection due to memory pressure.

Pull hwmon fix from Guenter Roeck:
 "Fix chip initialization/configuration in MAX6697 driver"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (max6697) fix MAX6581 ideality

Pull arm fixes fixes from Russell King:
 "This fixes a couple of problems with commit 48be69a0 ("ARM: move
  signal handlers into a vdso-like page"), one of which was originally
  discovered via my testing originally, but the fix for it was never
  actually committed.

  The other shows up on noMMU builds, and such platforms are extremely
  rare and as such are not part of my nightly testing"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: fix nommu builds with 48be69a0 (ARM: move signal handlers into a vdso-like page)
  ARM: fix a cockup in 48be69a0 (ARM: move signal handlers into a vdso-like page)

This change brings the suppressor attribute names into line; it also changes
the data types to provide a more consistent interface.

While -1 indicates that the suppressor is not enabled, values >= 0 for
suppress_prefixlen or suppress_ifgroup  reject routing decisions violating the
constraint.

This changes the previously presented behaviour of suppress_prefixlen, where a
prefix length _less_ than the attribute value was rejected. After this change,
a prefix length less than *or* equal to the value is considered a violation of
the rule constraint.

It also changes the default values for default and newly added rules (disabling
any suppression for those).
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanup 2 points for the usage of vlan_dev_priv(dev):
* In vlan_dev.c/vlan_dev_hard_header, we should use the var *vlan directly
  after grabing the pointer at the beginning with
        *vlan = vlan_dev_priv(dev);
  when we need to access the fields of *vlan.
* In vlan.c/register_vlan_device, add the var *vlan pointer
        struct vlan_dev_priv *vlan;
to cleanup the code to access the fields of vlan_dev_priv(new_dev).
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Olof reports that noMMU builds error out with:

arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'

This shows one of the evilnesses of IS_ENABLED().  Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Unfortunately, I never committed the fix to a nasty oops which can
occur as a result of that commit:

------------[ cut here ]------------
kernel BUG at /home/olof/work/batch/include/linux/mm.h:414!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe03080 #53
task: e90acac0 ti: e9be8000 task.ti: e9be8000
PC is at special_mapping_fault+0xa4/0xc4
LR is at __do_fault+0x68/0x48c

This doesn't show up unless you do quite a bit of testing; a simple
boot test does not do this, so all my nightly tests were passing fine.

The reason for this is that install_special_mapping() expects the
page array to stick around, and as this was only inserting one page
which was stored on the kernel stack, that's why this was blowing up.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

NetLabel has the ability to selectively assign network security labels
to outbound traffic based on either the LSM's "domain" (different for
each LSM), the network destination, or a combination of both.  Depending
on the type of traffic, local or forwarded, and the type of traffic
selector, domain or address based, different hooks are used to label the
traffic; the goal being minimal overhead.

Unfortunately, there is a bug such that a system using NetLabel domain
based traffic selectors does not correctly label outbound local traffic
that is not assigned to a socket.  The issue is that in these cases
the associated NetLabel hook only looks at the address based selectors
and not the domain based selectors.  This patch corrects this by
checking both the domain and address based selectors so that the correct
labeling is applied, regardless of the configuration type.

In order to acomplish this fix, this patch also simplifies some of the
NetLabel domainhash structures to use a more common outbound traffic
mapping type: struct netlbl_dommap_def.  This simplifies some of the code
in this patch and paves the way for further simplifications in the
future.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>