Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:

Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:

- A series of changes to add dra7 iodelay data used for mmc

- Add support for new beagleBoard-x15 revision c

- Fix logicpd-torpedo-37xx-devkit mmc card detect direction

* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
  ARM: dts: am57xx-beagle-x15: Add support for rev C
  ARM: dts: dra71-evm: Add pinmux configuration for MMC
  ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
  ARM: dts: dra72-evm: Add pinmux configuration for MMC
  ARM: dts: am572x-idk: Add pinmux configuration for MMC
  ARM: dts: am571x-idk: Add pinmux configuration for MMC
  ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
  ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
  ARM: dts: dra7-evm: Add pinmux configuration for MMC
  ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
  ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data

Fixes commit 687c2767 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")

This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.

This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]

Rev C is now in full production and boards are available for end users.

https://beagleboard.org/x15
https://github.com/beagleboard/beagleboard-x15/Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Nishanth Menon <nm@ti.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 32-bit DT changes for v4.14" from Kevin Hilman:

- update clock controler for use as reset controller
- misc. updates/fixups/improvements

* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson6: use stable UART bindings
  ARM: dts: meson: mark the clock controller also as reset controller
  ARM: dts: meson: add a node which describes the SRAM
  ARM: dts: meson8b: use the existing wdt node to override the compatible
  ARM: dts: meson8: add the PWM controller nodes
  ARM: dts: move the pwm_ab and pwm_cd nodes to meson.dtsi

Merge tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

Pull "ARM: Keystone DTS for 4.14" from Santosh Shilimkar:

Contents:
- ti-sci power domain, clock and reset controller support
- DSP nodes for k2h/k2l/k2e evms
- DSP CMA memory pools for k2h/k2l/k2e/keg evms
- MMC/hsmmc suport for k2g
- eDMA support for k2g
- DCAN support for k2g

* tag 'keystone_dts_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (22 commits)
  ARM: dts: keystone-k2g-ice: Add and enable DSP CMA memory pool
  ARM: dts: keystone-k2g-evm: Add and enable DSP CMA memory pool
  ARM: dts: keystone-k2g: Add DSP node
  ARM: dts: k2g: Add DCAN nodes
  dt-bindings: net: c_can: Update binding for clock and power-domains property
  ARM: dts: keystone-k2g-evm: Enable MMC0 and MMC1
  ARM: dts: keystone-k2g: add MMC0 and MMC1 nodes
  ARM: dts: keystone-k2g: Add eDMA nodes
  dt-bindings: ti,omap-hsmmc: Add 66AK2G mmc controller
  dt-bindings: ti,edma: Add 66AK2G specific information
  ARM: dts: keystone-k2g: Add gpio nodes
  ARM: dts: keystone-k2e-evm: Add and enable DSP CMA memory pool
  ARM: dts: keystone-k2l-evm: Add and enable common DSP CMA memory pool
  ARM: dts: keystone-k2hk-evm: Add and enable common DSP CMA memory pool
  ARM: dts: keystone-k2e: Add DSP node
  ARM: dts: keystone-k2l: Add DSP nodes
  ARM: dts: keystone-k2hk: Add DSP nodes
  ARM: dts: keystone-k2g: Add TI SCI reset-controller node
  ARM: dts: keystone-k2g: Add ti-sci clock provider node
  ARM: dts: keystone-k2g: Add ti-sci power domain node
  ...

Merge tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm Device Tree Changes for v4.14" from Andy Gross:

* Fixup XO, timer nodes, and pinctrl on IPQ4019
* Add IPQ4019 RNG and wifi blocks
* Update MSM8974 coresight node
* Add IPQ8074 bindings

* tag 'qcom-dts-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: add and enable both wifi blocks on the IPQ4019
  ARM: dts: qcom-msm8974: dts: Update coresight replicator
  ARM: dts: qcom: add pseudo random number generator on the IPQ4019
  ARM: dts: ipq4019: Move xo and timer nodes to SoC dtsi
  ARM: dts: ipq4019: Fix pinctrl node name
  dt-bindings: qcom: Add IPQ8074 bindings

Merge tag 'uniphier-dt-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

Pull "UniPhier ARM SoC DT updates for v4.14" from Masahiro Yamada:

- complete migrating to SPDX License Identifier
- remove support for old SoC
- add nodes for NAND, Audio pinctrl
- replace /include/ with #include

* tag 'uniphier-dt-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add Denali NAND controller node
  ARM: dts: uniphier use #include instead of /include/
  ARM: dts: uniphier: remove sLD3 SoC support
  ARM: dts: uniphier: add audio out pin-mux node
  ARM: dts: uniphier: use SPDX-License-Identifier (2nd)

Merge tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "Device tree changes for omaps for v4.14 merge window" from Tony Lindgren:

- A series of changes for dra7 and am572 to use generic
  MMC vqmmc regulator

- Clean-up tps65217 internal interrupts to define them
  only in tps65217.dtsi

- Add dra7 iodelay pinctrl driver configuration

- Add buzzer support for am437x-gp-evm

- Disable HDMI CEC internal pull-ups as it seems that
  all boards have an external pull for these

- Remove unnecessary interrupt-parent for omap3

- Configure droid 4 vaudio regulator initial mode and
  add vibrator

- Enable NAND dma prefetch for am335x-evm, am437x and dra7

- Add pcie1 dt node for EP mode for am57x and dra7

- Add support for new dra76x SoCs and dra76x-evm

* tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
  ARM: dts: nokia n900: update dts with camera support
  ARM: dts: Add support for dra76-evm
  ARM: dts: Add support for dra76x family of devices
  ARM: dts: DRA7: Add pcie1 dt node for EP mode
  ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
  ARM: dts: dra7xx: Enable NAND dma prefetch by default
  ARM: dts: am437xx: Enable NAND dma prefetch by default
  ARM: dts: am335x-evm: Enable NAND dma prefetch by default
  ARM: dts: omap4-droid4: Add vibrator
  ARM: dts: motorola-cpcap-mapphone: set initial mode for vaudio
  ARM: dts: omap3: Remove needless interrupt-parent property
  ARM: dts: Disable HDMI CEC internal pull-ups
  ARM: dts: am437x-gp-evm: Add support for buzzer
  ARM: dts: Add dra7 iodelay configuration
  ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
  ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
  ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"
  ARM: dts: am572x-idk: Fix GPIO polarity for MMC1 card detect
  ARM: dts: am571x-idk: Fix GPIO polarity for MMC1 card detect
  ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
  ...

Pull "mvebu dt for 4.14 (part 1)" from Gregory CLEMENT:

Add arm_global_timer node on Armada 38x

Fix PCI bus dtc warnings on mvebu 32 bits device tree files

* tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada-38x: Add arm_global_timer node
  ARM: dts: marvell: fix PCI bus dtc warnings

Merge tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt

Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:

* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: dts: gemini: add pin control set-up for the SoC
  ARM: dts: Add DTS file for D-Link DIR-685
  ARM: dts: gemini: Switch to using macros

Merge tag 'sunxi-dt-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner dts changes for 4.14" from Chen-Yu Tsai:

The usual improvement patches:

  - R_INTC interrupt controller compatible string update and device node
    addition

  - Battery charger enabled on the Cubietruck

  - New board: Bananapi M2 Magic

  - Ethernet and USB OTG enabled on the Beelink X2

  - MMC enabled for A83T boards

* tag 'sunxi-dt-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a83t: h8homlet: Enable micro-SD card and onboard eMMC
  ARM: dts: sun8i: a83t: cubietruck-plus: Enable micro-SD card and eMMC
  ARM: dts: sun8i: a83t: Add pingroup for 8-bit eMMC on mmc2
  ARM: dts: sun8i: a83t: Add MMC controller device nodes
  ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2
  ARM: dts: sun8i: h3: Enable USB OTG on the Beelink X2
  ARM: dts: sun8i: Add BananaPI M2-Magic DTS
  ARM: dts: sun7i: enable battery power supply subnode on cubietruck
  ARM: dts: sun8i: a83t: Add device node for R_INTC interrupt controller
  ARM: dts: sun8i: a23/a33: Use new sun6i-a31-r-intc compatible for NMI/R_INTC
  ARM: dts: sun6i: a31: Use new sun6i-a31-r-intc compatible for NMI/R_INTC

Merge tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts32 changes for 4.14" from Heiko Stübner:

Removal of the deprectated num-slots property from all Rockchip dw-mmc
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).

The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)

But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.

[0] https://github.com/OP-TEE/optee_os/pull/1666

* tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
  ARM: dts: rockchip: fix property-ordering in rv1108 mmc nodes
  ARM: dts: rockchip: enable sdmmc for rv1108 evb
  ARM: dts: rockchip: add efuse device node for rk3228
  ARM: dts: rockchip: add gpio power-key for rk3229-evb
  ARM: dts: rockchip: enable tsadc for rk3229-evb
  ARM: dts: rockchip: enable eMMC for rk3229-evb
  ARM: dts: rockchip: enable io-domain for rk3229-evb
  ARM: dts: rockchip: add cpu-supply property for cpu node of rk3229-evb
  ARM: dts: rockchip: add regulator nodes for rk3229-evb
  ARM: dts: rockchip: add sdmmc and sdio nodes for rk3228 SoC
  ARM: dts: rockchip: fix compatible string for eMMC node of rk3228 SoC
  ARM: dts: rockchip: add cpu enable method for rk3228 SoC
  ARM: dts: rockchip: remove num-slots from all platforms
  ARM: dts: rockchip: Add io-domain node for rk3228
  ARM: dts: rockchip: add basic dtsi file for RK3229 SoC
  ARM: dts: rockchip: enable adc key for rk3288-evb
  ARM: dts: rockchip: enable saradc for rk3288-evb
  ARM: dts: rockchip: enable ARM Mali GPU on rk3288-fennec
  ARM: dts: rockchip: enable ARM Mali GPU on rk3288-evb
  ARM: dts: rockchip: enable ARM Mali GPU on rk3288-tinker
  ...

Merge tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:

Changes of note:

* Add pin controller support to the RZ/G1M (r8a7743) SoC and
  RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.

* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
  is availabe in v4.13-rc1.

* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
  the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
  controller support noted above.

* Use R-Car Gen 2 fallback binding for vin nodes

  This makes binding use consistent across R-Car Gen 2 SoCs.
  It does not have any run-time effect

* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs

  Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
  bringup needs to copy a jump stub to on-SoC SRAM.  Currently it uses a
  hardcoded address pointing to ICRAM1."

* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs

  Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
  blocks of SRAM, which can be used for several purposes.  One such purpose
  is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
  and koelsch board.

  This is part of a tree-wide cleanup by Javier Martinez Canillas

* tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (38 commits)
  ARM: dts: iwg20m: Correct indentation of mmcif0 properties
  ARM: dts: rskrza1: Add LED0 pin support
  ARM: dts: rskrza1: Add SDHI1 pin group
  ARM: dts: rskrza1: Add Ethernet pin group
  ARM: dts: rskrza1: Add SCIF2 pin group
  ARM: dts: genmai: Add ethernet pin group
  ARM: dts: genmai: Add user led device nodes
  ARM: dts: genmai: Add RIIC2 pin group
  ARM: dts: genmai: Add SCIF2 pin group
  ARM: dts: r7s72100: Add pin controller node
  ARM: dts: iwg20m: Add MMCIF0 support
  ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for vin nodes
  ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for vin nodes
  ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for vin nodes
  ARM: dts: r8a7743: Add MMCIF0 support
  ARM: dts: r8a7794: Reserve SRAM for the SMP jump stub
  ARM: dts: r8a7793: Reserve SRAM for the SMP jump stub
  ARM: dts: r8a7792: Reserve SRAM for the SMP jump stub
  ARM: dts: r8a7791: Reserve SRAM for the SMP jump stub
  ARM: dts: r8a7790: Reserve SRAM for the SMP jump stub
  ...

Merge tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:

* Document R-Car D3 (r8a77995) SoC and Draak board

* Document reserved SRAM for the SMP jump stub on R-Car Gen2 and RZ/G1 SoCs

  Geert Uytterhoeven says, "+Renesas R-Car Gen2 and RZ/G1 SoCs need a small
  piece of SRAM for the jump stub +for secondary CPU bringup and CPU
  hotplug.  +This memory is reserved by adding a child node to a
  "mmio-sram" node..."

* Add a VSP channel index to DU vsps

  Laurent Pinchart says, "multiple LIF instances in the VSP. The current DT
  bindings don't support specifying that kind of SoC integration scheme.
  Extend them with a VSP channel index."

* Add R-Car M3-W (r8a7796) HDMI TX DT bindings

  This is compatible with existing R-Car H3 (r8a7795) support

* tag 'renesas-dt-bindings-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: Document Renesas Draak board DT bindings
  ARM: shmobile: Document R-Car D3 SoC DT bindings
  dt-bindings: display: rcar-du: Add a VSP channel index to the vsps DT property
  dt-bindings: sram: Document renesas,smp-sram
  dt-bindings: display: renesas: Add R-Car M3-W HDMI TX DT bindings

Merge tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt

Pull "STM32 DT updates for v4.14, round 1" from Alexandre Torgue:

Highlights:
----------
 -Add DMA support on STM32F746
 -Add DMA support on STM32H743
 -Add DAC support on STM32H743
 -Add DAC support on STM32F429
 -Add ADC support on STM32H743
 -Enable ADC on stm32h743i-eval board
 -Add CEC support on STM32F7xx MCUs
 -Enable CEC on stm32f769-disco board
 -Remove rdinit from stm32f4 boards

* tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: Add DMA support for STM32H743 SoC
  ARM: dts: stm32: Add DMA support for STM32F746 SoC
  ARM: dts: stm32: enable ADC on stm32h743i-eval board
  ARM: dts: stm32: add ADC support on stm32h743
  ARM: dts: stm32: Add DAC support on stm32h743
  ARM: dts: stm32: Add DAC support on stm32f429
  ARM: dts: stm32: enable CEC for stm32f769 discovery
  ARM: dts: stm32: add CEC for stm32f7 family
  ARM: dts: stm32: reorder stm32h743 nodes
  ARM: dts: stm32: Remove rdinit from bootargs on stm32f429-disco
  ARM: dts: stm32: Remove rdinit from bootargs on stm32f429i-eval
  ARM: dts: stm32: Remove rdinit from bootargs on stm32f469-disco

Merge tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Pull "Samsung DTS ARM changes for v4.13" from Krzysztof Kozłowski:

Remove deprecated and unneeded properties from Exynos boards.

* tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Remove num-slots from exynos platforms
  ARM: dts: exynos: Remove the OF graph from DSI node

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.

The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).

Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.

IOdelay data for both silicon revision 1.1 and 2.0 is
added here.

The datamanual revisions used are:
* AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.

IOdelay data for both silicon revision 1.0 and 2.0 is
added here.

The datamanual revisions used are:
 * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
 * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
 * DRA71x : SPRS960B, Revised February 2017
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4.  The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add camera support to N900 dts. Also add a note about MMC & debugging.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

dra76-evm is a board based on TI's dra76 processor targeting
for infotainment systems. Adding support for this platform.

dra76-evm and dra7-evm has a similar layout except with few differences.
So create a dra7-evm-common.dtsi with similarities on dra76-evm and
dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 2 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN

Adding basic dts support for DRA76 family while reusing the
data available in dra7.dtsi, dra74x.dtsi.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pcie1 dt node in order for the controller to operate in
endpoint mode. However since none of the dra7 based boards have
slots configured to operate in endpoint mode, keep EP mode
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for Moxa UC-8100-ME-T open platform

The UC-8100-ME-T computing platform is designed
for embedded data acquisition industrial applications

The features of UC-8100-ME-T series are:
* eMMC
* SPI flash
* SD slot
* 2x LAN
* 2 RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with USB signal
* USB host
* EEPROM
* TPM
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fix unit adress as suggested by Rob]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.

However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.

However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently the default method of prefetch polled shows the highest
possible read and write speed when minimal non NAND background
activity is being done. But it is also very CPU intensive to reach
these high speeds (CPU load of 99% via mtd performance tests). While
DMA prefetch only uses 50% of the CPU to achieve around 23% less in
top read and write performance.

However, as the non NAND CPU load increases the read and write
performance takes a large hit when using polled prefetch. Therefore,
prefetch dma mode ends up outperforming prefetch polled in general
"system level" test. So switch to using dma prefetch by default since
it is likely what most users would prefer.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add vibrator to Droid4's device tree.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Set default mode for vaudio, which may be left in standby mode
if the system is booted via kexec from Android.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

All nodes inhert "interrupt-parent" property from root
node. Removed the aforementioned property from usbhsohci,
usbhsehci, ssi_port1, ssi_port2 nodes to avoid duplication.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.

So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xs4all.nl>.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>