After Felix's patch it was still broken in case you
used more than just a single monitor interface. Fix
it better now.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is another case of data increasing the size of the
wiphy information significantly with a new feature, for
now remove this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some mlme work structs are not cancelled on disassociation
nor interface deletion, which leads to them running after
the memory has been freed

There is not a clean way to cancel these in the disassociation
logic because they must be canceled outside of the ifmgd->mtx
lock, so just cancel them in mgd_stop logic that tears down
the station.

This fixes the crashes we see in 3.7.9+.  The crash stack
trace itself isn't so helpful, but this warning gives
more useful info:

WARNING: at /home/greearb/git/linux-3.7.dev.y/lib/debugobjects.c:261 debug_print_object+0x7c/0x8d()
ODEBUG: free active (active state 0) object type: work_struct hint: ieee80211_sta_monitor_work+0x0/0x14 [mac80211]
Modules linked in: [...]
Pid: 14743, comm: iw Tainted: G         C O 3.7.9+ #11
Call Trace:
 [<ffffffff81087ef8>] warn_slowpath_common+0x80/0x98
 [<ffffffff81087fa4>] warn_slowpath_fmt+0x41/0x43
 [<ffffffff812a2608>] debug_print_object+0x7c/0x8d
 [<ffffffff812a2bca>] debug_check_no_obj_freed+0x95/0x1c3
 [<ffffffff8114cc69>] slab_free_hook+0x70/0x79
 [<ffffffff8114ea3e>] kfree+0x62/0xb7
 [<ffffffff8149f465>] netdev_release+0x39/0x3e
 [<ffffffff8136ad67>] device_release+0x52/0x8a
 [<ffffffff812937db>] kobject_release+0x121/0x158
 [<ffffffff81293612>] kobject_put+0x4c/0x50
 [<ffffffff8148f0d7>] netdev_run_todo+0x25c/0x27e

Cc: stable@vger.kernel.org
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Re-order the quiesce code so that timers are always
stopped before work-items are flushed. This was not
the problem I saw, but I think it may still be more
correct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When not using channel contexts with only monitor mode interfaces being
active, report local->monitor_chandef to userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the driver does not want a monitor mode VIF, no channel context is
allocated for it. This causes ieee80211_recalc_idle to put the hardware
into idle mode if only a monitor mode is active, breaking injection.

Fix this by checking local->monitors in addition to active channel
contexts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit 6c17b77b (mac80211: Fix tx queue
handling during scans) contains a bug that causes off-channel frames to
get queued when they should be handed down to the driver for transmit.
Prevent this from happening.
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Unicast frame with unknown forwarding information always trigger
the path discovery assuming destination is always located inside the
MBSS. This patch allows the forwarding to look for mesh gate if path
discovery inside the MBSS has failed.
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Just like the radar information, the TCP WoWLAN capability
data can increase the wiphy information and make it too
big. Remove the TCP WoWLAN information; no driver supports
it and new userspace tools will be required as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The wiphy information is getting very close to being too
much for a typical netlink dump message and adding the
radar attributes to channels and interface combinations
can push it over the limit, which means userspace gets no
information whatsoever. Therefore, remove these again for
now, no driver actually supports radar detection anyway
and a modified userspace is required as well.

We're working on a solution that will allow userspace to
request splitting the information across multiple netlink
messages, which will allow us to add this back.

Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ieee80211_beacon_add_tim() function might be called
by drivers with BHs enabled, which causes a potential
deadlock if TX happens at the same time and attempts to
lock the tim_lock as well. Use spin_lock_bh to fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the missing unlock before return from function brcmf_notify_vif_event()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unload sequence for mwifiex PCIE driver is as follows:
1. Invoking cleanup module from kernel results into
   pci_unregister_driver
2. Kernel invokes PCIE remove() handler which disconnects all
   interfaces.
3. One step during disconnect is to clean PCIE TX rings.
   During this we read txbd_rdptr from FW.

While loading driver next time, we see pci_enable_device()
results into system freeze. This may have happened because we
accessed PCI device after unregistering from bus driver.
Removing this ioread() operation resolves this bug.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the system suspends with mwifiex wifi powered on, and is then woken
by an ICMP ping packet, the ping response is discarded by the kernel
because the kernel incorrectly thinks there is no carrier.

I can't see any valid reason to want to report loss of carrier here,
so remove the offending code.

Fixes http://dev.laptop.org/ticket/12554Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When memory allocation using, kmalloc() fails, report appropriate error value.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes an instance of DMA buffer on stack(being passed to
usb_control_msg) for the wireless USB version of the Agere Orinoco card driver.
It also fixes the missing audit for the return value of firmware download
routine. Found using smatch.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
	struct {
		u8 data[254];
		struct usb_ctrlrequest dr;
	};

Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.

Patch changes setup packet to be allocated separately.

[v2]:
 - Use WARN_ON_ONCE instead of WARN_ON

Cc: <stable@vger.kernel.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For STA mode, collect VHT realated IEs from the Beacons or Probe
Responses and append similar VHT related IEs to association
requests.

For AP mode, get VHT related capability information and share it
with cfg80211 at the time of wiphy register. This information is
further used by cfg80211 and hostapd to start an AP with 802.11AC
support.

Currently only 8897 supports 802.11AC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They all can make one line.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While unloading driver, we free all pending TX packets by flushing
TX ring. There is unhandled case for PCIE8897 while checking for
ring empty condition.

This patch adds the handling by calling mwifiex_pcie_txbd_empty().
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I removed a bit too much info last time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Theoretically, the card may not enter CTKILL:
In case the timer that iwl_prepare_ct_kill_task is setting,
will expire before tt->state revert to its previous state.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The time event data structures are required also for P2P Device
interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Occasionally, we would run into this warning:

  iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left
  iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601
  iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9
  iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9
  iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601
  iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1
  wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3)
  ------------[ cut here ]------------
  WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]()
  Modules linked in: [...]
  Call Trace:
   [<c1046e42>] warn_slowpath_common+0x72/0xa0
   [<c1046e92>] warn_slowpath_null+0x22/0x30
   [<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]
   [<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm]
   [<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm]
   [<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211]

The reason is a problem with asynchronous vs. synchronous
commands, what happens here is the following:
 * TE 0x2601 is removed, the TIME_EVENT_CMD for that is async
 * a new TE (will be 0x2701) is created, the TIME_EVENT_CMD
   for that is sync and also uses a notification wait for the
   response (to avoid another race condition)
 * the response for the TE 0x2601 removal comes from the
   firmware, and is handled by the notification wait handler
   that's really waiting for the second response, but can't
   tell the difference, we therefore see the message
   "TIME_EVENT_CMD response - UID = 0x2601" instead of
   "TIME_EVENT_CMD response - UID = 0x2701".

Fix this issue by making the TE removal synchronous as well,
this means that we wait for the response to that command
first, before there's any chance of sending a new one.

Also, to detect such issues more easily in the future, add
a warning to the notification handler that detects them.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is helpful for debugging the time event warning,
but also in general to see what's going on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

All station commands must include a valid MAC ID,
the ID 0 is randomly valid in some cases, but we
must set the ID properly. Do that by passing the
right station and using its mac_id_n_color.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For the firmware to know when DTIM beacons arrive
we have to program the DTIM time in TSF and system
time in the MAC context. Since mac80211 now tracks
the different times (on demand), this becomes easy.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
while the mac80211-next tree removed
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Larry noticed (and bisected) that commit df881293
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.

Cc: Jouni Malinen <j@w1.fi>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If mesh plink debugging is enabled, this gets annoying in
a crowded environment, fast.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Convert mesh peering events into strings and make the
debug output a little easier to read. Also stop printing
the llid and plid since these don't change across peering
states and are random numbers anyway so they just amount
to noise.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ieee80211_ht_cap_ie_to_sta_ht_cap() will clean up the
ht_supported flag and station bandwidth field for us
if the peer beacon doesn't have an HT capability element
(is operating as non-HT).

Also, we don't really need a special station ch_width
member to track the station operating mode any more so use
sta.bandwidth instead.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If an interface is set down while authenticating or
associating, there's a station entry that will be
removed by the flushing in do_stop() and that will
cause a warning. It's otherwise harmless, but avoid
the warning by calling ieee80211_mgd_stop() first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Update the 802.11 book to list the correct
data structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>