Merge branch 'for-2635/gpio2' into for-linus/samsung2

Merge branch 'for-2635/rx1950' into for-linus/samsung2

Merge branch 'for-2635/acer-n35' into for-linus/samsung2

Merge branch 'for-2635/samsung-clock' into for-linus/samsung2

Merge branch 'for-2635/samsung-hwmon' into for-linus/samsung2

Merge branch 'for-2635/samsung-dma' into for-linus/samsung2

Merge branch 'for-2635/s5p-general' into for-linus/samsung2

Merge branch 'for-2635/s3c24xx-general' into for-linus/samsung2

This patch adds GPIOlib support for S5PV210.
Signed-off-by: Pannaga Bhushan <p.bhushan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Timer interrupts range was defined as 43-47, what overlaps with VIC0 range
(32-64). This was caused probably by a typo while the common interrupts
definition was refactored. This patch moves timer interrupt range to safe
area of 11-15 (just before uart range).

This fixes the commit 87aef30e
("ARM: S5P: Change S5P_TIMER_IRQ based to 11 for SAMSUNG S5P series.")
which meant to move these into the old (and previously reserved)
ISA space.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The pm-gpio.c code was incrementing the gpio_nr from the nr_gpios
field and the bank-bank offset inside the loop, and also in the
for() loop with a ++.

Remove the ++, as the number is already at the next GPIO, thus
ensuring that we don't skip a gpio bank by accident.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add a table for the GPIO bank sizes for each SoC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

As part of the cleanup, remove the old macros mapping GPIO numbers
to the base of the register now we have gpiolib to manage the GPIO
mappings for us.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Update a couple of S3C24XX and S3C2412 files that are still
using the GPIO number to register mapping calls to get the
s3c_gpio_chip and use the base field from that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Start cleaning up the numbering of GPIO banks by removing the old
bank start definitions currently being used by some of the header
files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Increase GPIOs number for S3C244X, and make S3C_GPIO_END
point to BANKJ end, otherwise gpiolib refuses to register
BANKJ
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[ben-linux@fluff.org: Move pm fix to new patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Seems like a typo, wrong setup leads to broken image on ipaq screen.
Signed-off-by: Mike Solovyev <ms@sk.2-ch.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

All other functions have the channel argument of type 'unsigned int'
the s3c2410_dma_devconfig also accept the same value as argument but
treat it as type 'int'. Remove this anomaly by make it 'unsigned int'.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move HWMON platform definition from plat-s3c24xx to plat-samsung
and adjust mach-bast to use the new s3c_hwmon_set_platdata().
This allows usage of dev-hwmon by other Samsung SoCs.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch removes static of s5p6440_sysclass, s5p6442_sysclass,
and s5pv210_sysclass for defintion as extern.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The address ben@fluff.org is old, ben-linux@fluff.org has been in use
for a long time, and we should fixup all the occasions of the older
address to avoid confusion.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

According to datasheet GPG13-15 must be configured as input in NAND
boot mode, otherwise device will not be able to wake up
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

If PM_H1940 is enabled, kernel _must_ be located upper then 0x30008000,
because this area (0x30000000-0x30100000) can be used by bootloader. If
kernel is located at 0x30008000, bootloader will corrupt kernel's code during
resume.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Denis Grigoriev <dgreenday@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add locking to each GPIO bank to allow for SMP capable code
to use the gpiolib functions. See the gpio-core.h header file
for more information.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add USB external crystal clock definition Xusbxti to common S5P clock code.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch fixes return value in below functions
- pwm_cfg_src_is_tclk
- tcfg_to_divisor
- pwm_tdiv_has_div1
- pwm_tdiv_div_bits

And this patch changes Copyright ordering.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch fixes return value in below functions
- pwm_cfg_src_is_tclk
- tcfg_to_divisor
- pwm_tdiv_has_div1
- pwm_tdiv_div_bits

And this patch changes Copyright ordering.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This patch fixes return value in below functions
- pwm_cfg_src_is_tclk
- tcfg_to_divisor
- pwm_tdiv_has_div1
- pwm_tdiv_div_bits

And this patch changes Copyright ordering, and addes 'based on' information.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The n30_init_irq() call is simply a call to s3c24xx_init_irq, so
just remove it and update the machine definitions to call the IRQ
initialision call directly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move to using gpio_request() and gpio_set_value() for the MMC power
control calls.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

There is bug in USB setup code for Acer n35 (it is related directly to s3c2410,
see doc). We want suspend host port (is not connected) but device port should be
active.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

All code already present for Acer n35 is useless unless MACH_N35 is defined.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
[ben-linux@fluff.org: minor edit of subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Remove the _INP definitions, they are all zero and also unused
Signed-off-by: Ben Dooks <ben-linux@fluff.org>