- 27 Mar, 2014 24 commits
-
-
Andrea Merello authored
rtl8180 has one register for analog converters setting ,rtl8185 has two and rtl8187se has three. Setting those registers require more than a simple write, and for one of them a function is already provided. This patch introduces functions for the other two. rtl8187se will use them. rtl8185 doesen't yet, but should Signed-off-by:
Andrea Merello <andrea.merello@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Andrea Merello authored
rtl8187se nees extra parameters to be read from the eeprom. This patch adds support for it Signed-off-by:
-
Andrea Merello authored
configuration of carbus-related registers is different for rtl8187se. Introduce a dedicated function that does it for all cards in the proper way Signed-off-by:
-
Andrea Merello authored
This patch adds tx queue mapping for rtl8187se and a long comment block about their usages. It adapts the TX function to use that map and it sets properly the TX descriptor rtl8187se-only fields Signed-off-by:
-
Andrea Merello authored
MAR registers are not present in rtl8187se, and attempting to write to them must be avoided Signed-off-by:
-
Andrea Merello authored
This patch introduces two dedicated functions for enabling and disabling ints. Support for rtl8187se is also added to them Signed-off-by:
-
Andrea Merello authored
rtl8187se has more queues and different ISR flags. This patch adds a separated ISR handler for rtl8187se Signed-off-by:
-
Andrea Merello authored
Currently RX status descriptor and RX command descriptor are represented using the same struct type. This patch splits this by introducing different types for rx status and command descriptor. Doing this make it possible to handle rtl8187se RX descriptors easier. This patch do also this by adding specific cases where needed. Signed-off-by:
-
Andrea Merello authored
Basic rate configuration is a bit different for rtl8187se. Adding this also fixes the gcc warning introduced in last patch about unhandled case in switch. Signed-off-by:
-
Andrea Merello authored
This patch modifies the TX descriptor struct so it can work also for rtl8187se. Some reserved field is now meaningful, and where needed union is used. Signed-off-by:
-
Andrea Merello authored
Add back rtl8187se chip type to the enum for known chips. This causes unhandled switch/case warning that will be fixed in following patch Signed-off-by:
-
Andrea Merello authored
Adds registers for rtl8187se to the rtl818x common struct Signed-off-by:
-
Amitkumar Karwar authored
Sometimes we may end up downloading other commands when host sleep is configured. This patch makes sure that pending commands are cancelled and we stop queueing further commands during host sleep. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
Incremented sequence number was not being used for SLEEP confirm command. This patch fixes the issue. Signed-off-by:
-
Amitkumar Karwar authored
When next scan command is delayed due to Tx traffic and meanwhile synchronous command is received followed by a signal, we cance all pending commands. NULL pointer dereference is seen in this case while queueing next command in scan delay timer. This patch adds a check to fix this issue. Signed-off-by:
-
Daniel Kim authored
The struct cfg80211_connect_params indicate whether the connection should use management frame protection (mfp). If required set the MFP_CAPABLE flag in the firmware command. This is supported from user-space by wpa_supplicant since v2.1. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Around these changes: o Remove unnecessary parentheses o Use consistent dereference style (change ptr[0] to *ptr) o Argument alignment Done via coccinelle script: (and some typing) $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
-
Joe Perches authored
Using addressof then casting to the original type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast.cocci @@ type T; T foo; @@ - (T *)&foo + &foo Signed-off-by:
-
Andrea Merello authored
On currently supported HW there are four TX queues (three for normal packets and one for beacons). The driver uses just one TX queue, and declare to mac80211 to support just one queue, but it allocates coherent memory for all queues. Furthermore the TX is code is written assumimg four queues exists, and even if we decide to enable more queues in future, its mapping rule to mac80211 is fixed. This means we have memory waste on rtl8180/rtl8185, and we have also not enough flexibility to add support for boards (rtl8187se) that will use more queues. This patch changes things in order to allocate coherent memory only for the queues effectively used and it make it possible to specify how to map hardware queues on mac80211 queues, that will be used by rtl8187se code as soon it will be merged. Note: even if the beacon queue is currently unused, this should change, so I kept it. Signed-off-by:
-
Andrea Merello authored
Hw DMA registers are written in rtl8180_init_hw function. They are also written again just after calling rtl8180_init_hw. There is no point in doing this twice. Remove those redundant register writes from rtl8180_start. Signed-off-by:
-
Rafał Miłecki authored
Some Broadcom boards have more GPIOs available. For example Linksys E3200 home router is based on SoC id 0x5357, package 0x0A and uses GPIO 23 to reset internal USB WiFi (gpio23=wombo_reset). Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
- 26 Mar, 2014 1 commit
-
-
Johan Hedberg authored
We should let user space request the peer address also in the pending connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user space code that tries to do this and will fail without extending the set of allowed states for the peer address information. This patch adds the two states to the allowed ones in the L2CAP and RFCOMM sock_getname functions, thereby preventing ENOTCONN from being returned. Reported-by:
Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Tested-by:
Marcel Holtmann <marcel@holtmann.org>
-
- 24 Mar, 2014 8 commits
-
-
Johan Hedberg authored
The smp variable in smp_conn_security is not used anywhere before the smp = smp_chan_create() call in the smp_conn_security function so it makes no sense to assign any other value to it before that. Signed-off-by:
-
Johan Hedberg authored
The smp pointer might not be initialized for jumps to the "done" label in the smp_conn_security function. Furthermore doing the set_bit after done might "overwrite" a previous value of the flag in case pairing was already in progress. This patch moves the call to set_bit before the label so that it is only done for a newly created smp context (as returned by smp_chan_create). Signed-off-by:
-
Johan Hedberg authored
Due to several devices being unable to handle this procedure reliably (resulting in forced disconnections before pairing completes) it's better to remove it altogether. Signed-off-by:
-
Johan Hedberg authored
In the case that the just-works model would be triggered we only want to confirm remotely initiated pairings (i.e. those triggered by a Security Request or Pairing Request). This patch adds the necessary check to the tk_request function to fall back to the JUST_WORKS method in the case of a locally initiated pairing. Signed-off-by:
-
Johan Hedberg authored
For remotely initiated just-works pairings we want to show the user a confirmation dialog for the pairing. However, we can only know which side was the initiator by tracking which side sends the first Security Request or Pairing Request PDU. This patch adds a new SMP flag to indicate whether our side was the initiator for the pairing. Signed-off-by:
-
Johan Hedberg authored
In the case that a local pairing confirmation (JUST_CFM) has been selected as the method we need to use the user confirm request mgmt event for it with the confirm_hint set to 1 (to indicate confirmation without any specific passkey value). Without this (if passkey_notify was used) the pairing would never proceed. This patch adds the necessary call to mgmt_user_confirm_request in this scenario. Signed-off-by:
-
Johan Hedberg authored
It is possible that the HCI_LE_Start_Encryption command fails in an early stage and triggers a command status event with the failure code. In such a case we need to properly notify the hci_conn object and cleanly bring the connection down. This patch adds the missing command status handler for this HCI command. Signed-off-by:
-
Johan Hedberg authored
If a sudden disconnection happens the l2cap_conn pointer may already have been cleaned up by the time hci_conn_security gets called, resulting in the following oops if we don't have a proper NULL check: BUG: unable to handle kernel NULL pointer dereference at 000000c8 IP: [<c132e2ed>] smp_conn_security+0x26/0x151 *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC CPU: 1 PID: 673 Comm: memcheck-x86-li Not tainted 3.14.0-rc2+ #437 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: f0ef0520 ti: f0d6a000 task.ti: f0d6a000 EIP: 0060:[<c132e2ed>] EFLAGS: 00010246 CPU: 1 EIP is at smp_conn_security+0x26/0x151 EAX: f0ec1770 EBX: f0ec1770 ECX: 00000002 EDX: 00000002 ESI: 00000002 EDI: 00000000 EBP: f0d6bdc0 ESP: f0d6bda0 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 CR0: 80050033 CR2: 000000c8 CR3: 30f0f000 CR4: 00000690 Stack: f4f55000 00000002 f0d6bdcc c1097a2b c1319f40 f0ec1770 00000002 f0d6bdd0 f0d6bde8 c1312a82 f0d6bdfc c1312a82 c1319f84 00000008 f4d81c20 f0e5fd86 f0ec1770 f0d6bdfc f0d6be28 c131be3b c131bdc1 f0d25270 c131be3b 00000008 Call Trace: [<c1097a2b>] ? __kmalloc+0x118/0x128 [<c1319f40>] ? mgmt_pending_add+0x49/0x9b [<c1312a82>] hci_conn_security+0x4a/0x1dd [<c1312a82>] ? hci_conn_security+0x4a/0x1dd [<c1319f84>] ? mgmt_pending_add+0x8d/0x9b [<c131be3b>] pair_device+0x1e1/0x206 [<c131bdc1>] ? pair_device+0x167/0x206 [<c131be3b>] ? pair_device+0x1e1/0x206 [<c131ed44>] mgmt_control+0x275/0x2d6 Signed-off-by:
-
- 23 Mar, 2014 1 commit
-
-
Thomas Gleixner authored
Make sure no timer callback is running before releasing the datastructure which contains it. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
- 21 Mar, 2014 2 commits
-
-
Marcel Holtmann authored
The LE scan type paramter defines if active scanning or passive scanning is in use. Track the currently set value so it can be used for decision making from other pieces in the core. Signed-off-by:
-
Amitkumar Karwar authored
If vendor specific HCI commands are received from application, we should send corresponding events to stack. These events should be consumed in driver, only if they are for the internal HCI commands generated by driver. This patch fixes the vendor command 0x3f stuck problem with above mentioned change. For example, hcitool cmd 3f 22 fe 06 22 21 20 43 50 00 Signed-off-by:
-
- 20 Mar, 2014 4 commits
-
-
Johan Hedberg authored
We need to ensure that we do not send events to user space with the identity address if we have not yet notified user space of the IRK. The code was previously trying to handle this for the mgmt_pair_device response (which worked well enough) but this is not the only connection related event that might be sent to user space before pairing is successful: another important event is Device Disconnected. The issue can actually be solved more simply than the solution previously used for mgmt_pair_device. Since we do have the identity address tracked as part of the remote IRK struct we can just copy it over from there to the hci_conn struct once we've for real sent the mgmt event for the new IRK. Signed-off-by:
-
Arend van Spriel authored
In order to support the driver behaviour introduced by: commit d0575a5a703978c43e25128421158c78534ba100 Author: Daniel Kim <dekim@broadcom.com> Date: Wed Mar 12 18:12:14 2014 -0700 brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning in devices that do not support bwcap firmware command a fallback is added. Reviewed-by: -
Arend van Spriel authored
In the function brcmf_sdiod_request_data() an error message is logged, but the calling function retries it. This patch will only log an error message when retry limit is reached. The low-level error is still logged by a SDIO debug message. Reviewed-by:
-
Arend van Spriel authored
The watchdog thread waits on completion that is set from a timer. As the completion is count based this could mean that on a busy system the watchdog is handled multiple times with a very short interval. This is not the intended behaviour. After handling the watchdog it should wait for the next timer expiry. This is accomplished by reinitializing the completion. Reviewed-by:
-
