- 16 Jul, 2012 40 commits
-
-
Andrea Arcangeli authored
commit 26c19178 upstream. When holding the mmap_sem for reading, pmd_offset_map_lock should only run on a pmd_t that has been read atomically from the pmdp pointer, otherwise we may read only half of it leading to this crash. PID: 11679 TASK: f06e8000 CPU: 3 COMMAND: "do_race_2_panic" #0 [f06a9dd8] crash_kexec at c049b5ec #1 [f06a9e2c] oops_end at c083d1c2 #2 [f06a9e40] no_context at c0433ded #3 [f06a9e64] bad_area_nosemaphore at c043401a #4 [f06a9e6c] __do_page_fault at c0434493 #5 [f06a9eec] do_page_fault at c083eb45 #6 [f06a9f04] error_code (via page_fault) at c083c5d5 EAX: 01fb470c EBX: fff35000 ECX: 00000003 EDX: 00000100 EBP: 00000000 DS: 007b ESI: 9e201000 ES: 007b EDI: 01fb4700 GS: 00e0 CS: 0060 EIP: c083bc14 ERR: ffffffff EFLAGS: 00010246 #7 [f06a9f38] _spin_lock at c083bc14 #8 [f06a9f44] sys_mincore at c0507b7d #9 [f06a9fb0] system_call at c083becd start len EAX: ffffffda EBX: 9e200000 ECX: 00001000 EDX: 6228537f DS: 007b ESI: 00000000 ES: 007b EDI: 003d0f00 SS: 007b ESP: 62285354 EBP: 62285388 GS: 0033 CS: 0073 EIP: 00291416 ERR: 000000da EFLAGS: 00000286 This should be a longstanding bug affecting x86 32bit PAE without THP. Only archs with 64bit large pmd_t and 32bit unsigned long should be affected. With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad() would partly hide the bug when the pmd transition from none to stable, by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is enabled a new set of problem arises by the fact could then transition freely in any of the none, pmd_trans_huge or pmd_trans_stable states. So making the barrier in pmd_none_or_trans_huge_or_clear_bad() unconditional isn't good idea and it would be a flakey solution. This should be fully fixed by introducing a pmd_read_atomic that reads the pmd in order with THP disabled, or by reading the pmd atomically with cmpxchg8b with THP enabled. Luckily this new race condition only triggers in the places that must already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix is localized there but this bug is not related to THP. NOTE: this can trigger on x86 32bit systems with PAE enabled with more than 4G of ram, otherwise the high part of the pmd will never risk to be truncated because it would be zero at all times, in turn so hiding the SMP race. This bug was discovered and fully debugged by Ulrich, quote: ---- [..] pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and eax. 496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t *pmd) 497 { 498 /* depend on compiler for an atomic pmd read */ 499 pmd_t pmdval = *pmd; // edi = pmd pointer 0xc0507a74 <sys_mincore+548>: mov 0x8(%esp),%edi ... // edx = PTE page table high address 0xc0507a84 <sys_mincore+564>: mov 0x4(%edi),%edx ... // eax = PTE page table low address 0xc0507a8e <sys_mincore+574>: mov (%edi),%eax [..] Please note that the PMD is not read atomically. These are two "mov" instructions where the high order bits of the PMD entry are fetched first. Hence, the above machine code is prone to the following race. - The PMD entry {high|low} is 0x0000000000000000. The "mov" at 0xc0507a84 loads 0x00000000 into edx. - A page fault (on another CPU) sneaks in between the two "mov" instructions and instantiates the PMD. - The PMD entry {high|low} is now 0x00000003fda38067. The "mov" at 0xc0507a8e loads 0xfda38067 into eax. ---- Reported-by:
Ulrich Obergfell <uobergfe@redhat.com> Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Larry Woodman <lwoodman@redhat.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tom Hughes authored
commit 6bb51c70 upstream. Commit 3a2923e8 introduced a bug when a corrupt descriptor is encountered - although the following descriptor is discarded and returned to the queue for reuse the associated frame is also returned for processing. This leads to a panic: BUG: unable to handle kernel NULL pointer dereference at 000000000000003a IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k] Call Trace: <IRQ> [<ffffffff812d7fa0>] ? map_single+0x60/0x60 [<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k] [<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k] [<ffffffff8105e133>] tasklet_action+0x63/0xd0 [<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0 [<ffffffff8101a873>] ? native_sched_clock+0x13/0x80 [<ffffffff815f9d5c>] call_softirq+0x1c/0x30 [<ffffffff810151f5>] do_softirq+0x75/0xb0 [<ffffffff8105df95>] irq_exit+0xb5/0xc0 [<ffffffff815fa5b3>] do_IRQ+0x63/0xe0 [<ffffffff815f0cea>] common_interrupt+0x6a/0x6a <EOI> [<ffffffff8131840a>] ? intel_idle+0xea/0x150 [<ffffffff813183eb>] ? intel_idle+0xcb/0x150 [<ffffffff814a1db9>] cpuidle_enter+0x19/0x20 [<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240 [<ffffffff8101c4bf>] cpu_idle+0xaf/0x120 [<ffffffff815cda8e>] rest_init+0x72/0x74 [<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4 [<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e [<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135 [<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f Making sure bf is cleared to NULL in this case restores the old behaviour. Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Cc: Josh Boyer <jwboyer@redhat.com> Signed-off-by:
-
Matt Carlson authored
commit b7abee6e upstream. 5906 devices also need the short DMA fragment workaround. This patch makes the necessary change. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Tested-by:
Christian Kujau <lists@nerdbynature.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Josh Boyer <jwboyer@redhat.com> Signed-off-by:
-
Shaohua Li authored
commit fab363b5 upstream. There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but the two bits have relationship. A delayed stripe can be moved to hold list only when preread active stripe count is below IO_THRESHOLD. If a stripe has both the bits set, such stripe will be in delayed list and preread count not 0, which will make such stripe never leave delayed list. Signed-off-by:
Shaohua Li <shli@fusionio.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Hans de Goede authored
commit af05ef01 upstream. [Backport to linux-stable by Antonio Ospite <ospite@studenti.unina.it>] This fixes a regression introduced by commit f7059eaa and should be backported to all supported stable kernels which have this commit. Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Tested-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
-
Bing Zhao authored
commit 858faa57 upstream add_virtual_intf() needs to return an ERR_PTR(), instead of NULL, on errors, otherwise cfg80211 will crash. Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Vaibhav Nagarnaik authored
commit 71babb27 upstream. According to Documentation/trace/ftrace.txt: tracing_cpumask: This is a mask that lets the user only trace on specified CPUS. The format is a hex string representing the CPUS. The tracing_cpumask currently doesn't affect the tracing state of per-CPU ring buffers. This patch enables/disables CPU recording as its corresponding bit in tracing_cpumask is set/unset. Link: http://lkml.kernel.org/r/1336096792-25373-3-git-send-email-vnagarnaik@google.com Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Laurent Chavey <chavey@google.com> Cc: Justin Teravest <teravest@google.com> Cc: David Sharp <dhsharp@google.com> Signed-off-by:
Vaibhav Nagarnaik <vnagarnaik@google.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Johannes Berg authored
commit 882b7b7d upstream. When debugging is disabled, the event log functions aren't functional in the way that the debugfs file expects. This leads to the debugfs access crashing. Since the event log functions aren't functional then, remove the debugfs file when CONFIG_IWLWIFI_DEBUG is not set. Reported-by:
Lekensteyn <lekensteyn@gmail.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Johannes Berg authored
No upstream commit, the buggy code was removed in 3.5 in commit 7213cf2c and others. Rajkumar changed code for handling channel switching in mac80211 to stop the queues in commit 7cc44ed4 Author: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Date: Fri Sep 16 15:32:34 2011 +0530 mac80211: Fix regression on queue stop during 2040 bss change which went into 3.2. In the 3.4 cycle, Paul's change commit 3117bbdb Author: Paul Stewart <pstew@chromium.org> Date: Tue Mar 13 07:46:18 2012 -0700 mac80211: Don't let regulatory make us deaf went in and changed the TX/RX enable logic, but now the conditions for stopping and restarting the queues were different so that now, if the AP changes between 20/40 MHz bandwidth, it can happen that we stop but never restart the queues. This breaks the connection and the module actually has to be reloaded to get it back to work. Fix this by making sure the queues are always started when they were stopped. Reported-by:
Florian Manschwetus <manschwetus@googlemail.com> Signed-off-by:
-
Stanislav Kinsbursky authored
upstream commit 12918b10. In case of destroying mount namespace on child reaper exit, nsproxy is zeroed to the point already. So, dereferencing of it is invalid. This patch hard-code "init_net" for all network namespace references for NFS callback services. This will be fixed with proper NFS callback containerization. Signed-off-by:
Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Stanislav Kinsbursky authored
upstream commit 786185b5. The idea is to separate service destruction and per-net operations, because these are two different things and the mix looks ugly. Notes: 1) For NFS server this patch looks ugly (sorry for that). But these place will be rewritten soon during NFSd containerization. 2) LockD per-net counter increase int lockd_up() was moved prior to make_socks() to make lockd_down_net() call safe in case of error. Signed-off-by:
-
Stanislav Kinsbursky authored
upstream commit 9793f7c8. This new routine is responsible for service registration in a specified network context. The idea is to separate service creation from per-net operations. Note also: since registering service with svc_bind() can fail, the service will be destroyed and during destruction it will try to unregister itself from rpcbind. In this case unregistration has to be skipped. Signed-off-by:
-
Stanislav Kinsbursky authored
upstream commit e3f70ead. v2: dereference of most probably already released nlm_host removed in nlmclnt_done() and reclaimer(). These routines are called from locks reclaimer() kernel thread. This thread works in "init_net" network context and currently relays on persence on lockd thread and it's per-net resources. Thus lockd_up() and lockd_down() can't relay on current network context. So let's pass corrent one into them. Signed-off-by:
-
Davide Gerhard authored
commit 6de0298e upstream. This adds support for the iPad to the ipheth driver. (product id = 0x129a) Signed-off-by:
Davide Gerhard <rainbow@irh.it> Signed-off-by:
-
Alan Stern authored
commit dbf0e4c7 upstream. Quite a few ASUS computers experience a nasty problem, related to the EHCI controllers, when going into system suspend. It was observed that the problem didn't occur if the controllers were not put into the D3 power state before starting the suspend, and commit 151b6128 (USB: EHCI: fix crash during suspend on ASUS computers) was created to do this. It turned out this approach messed up other computers that didn't have the problem -- it prevented USB wakeup from working. Consequently commit c2fb8a3f (USB: add NO_D3_DURING_SLEEP flag and revert 151b6128) was merged; it reverted the earlier commit and added a whitelist of known good board names. Now we know the actual cause of the problem. Thanks to AceLan Kao for tracking it down. According to him, an engineer at ASUS explained that some of their BIOSes contain a bug that was added in an attempt to work around a problem in early versions of Windows. When the computer goes into S3 suspend, the BIOS tries to verify that the EHCI controllers were first quiesced by the OS. Nothing's wrong with this, but the BIOS does it by checking that the PCI COMMAND registers contain 0 without checking the controllers' power state. If the register isn't 0, the BIOS assumes the controller needs to be quiesced and tries to do so. This involves making various MMIO accesses to the controller, which don't work very well if the controller is already in D3. The end result is a system hang or memory corruption. Since the value in the PCI COMMAND register doesn't matter once the controller has been suspended, and since the value will be restored anyway when the controller is resumed, we can work around the BIOS bug simply by setting the register to 0 during system suspend. This patch (as1590) does so and also reverts the second commit mentioned above, which is now unnecessary. In theory we could do this for every PCI device. However to avoid introducing new problems, the patch restricts itself to EHCI host controllers. Finally the affected systems can suspend with USB wakeup working properly. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632 Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728Based-on-patch-by:
AceLan Kao <acelan.kao@canonical.com> Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Dâniel Fraga <fragabr@gmail.com> Tested-by:
Javier Marcet <jmarcet@gmail.com> Tested-by:
Andrey Rahmatullin <wrar@wrar.name> Tested-by:
Oleksij Rempel <bug-track@fisher-privat.net> Tested-by:
Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
-
Sarah Sharp authored
commit 0d9f78a9 upstream. The Microsoft LifeChat 3000 USB headset was causing a very reproducible hang whenever it was plugged in. At first, I thought the host controller was producing bad transfer events, because the log was filled with errors like: xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD However, it turned out to be an xHCI driver bug in the ring expansion patches. The bug is triggered When there are two ring segments, and a TD that ends just before a link TRB, like so: ______________ _____________ | | ---> | setup TRB B | ______________ | _____________ | | | | data TRB B | ______________ | _____________ | setup TRB A | <-- deq | | data TRB B | ______________ | _____________ | data TRB A | | | | <-- enq, deq'' ______________ | _____________ | status TRB A | | | | ______________ | _____________ | link TRB |--------------- | link TRB | _____________ <--- deq' _____________ TD A (the first control transfer) stalls on the data phase. That halts the ring. The xHCI driver moves the hardware dequeue pointer to the first TRB after the stalled transfer, which happens to be the link TRB. Once the Set TR dequeue pointer command completes, the function update_ring_for_set_deq_completion runs. That function is supposed to update the xHCI driver's dequeue pointer to match the internal hardware dequeue pointer. On the first call this would work fine, and the software dequeue pointer would move to deq'. However, if the transfer immediately after that stalled (TD B in this case), another Set TR Dequeue command would be issued. That would move the hardware dequeue pointer to deq''. Once that command completed, update_ring_for_set_deq_completion would run again. The original code would unconditionally increment the software dequeue pointer, which moved the pointer off the ring segment into la-la-land. The while loop would happy increment the dequeue pointer (possibly wrapping it) until it matched the hardware pointer value. The while loop would also access all the memory in between the first ring segment and the second ring segment to determine if it was a link TRB. This could cause general protection faults, although it was unlikely because the ring segments came from a DMA pool, and would often have consecutive memory addresses. If nothing in that space looked like a link TRB, the deq_seg pointer for the ring would remain on the first segment. Thus, the deq_seg and the software dequeue pointer would get out of sync. When the next transfer event came in after the stalled transfer, the xHCI driver code would attempt to convert the software dequeue pointer into a DMA address in order to compare the DMA address for the completed transfer. Since the deq_seg and the dequeue pointer were out of sync, xhci_trb_virt_to_dma would return NULL. The transfer event would get ignored, the transfer would eventually timeout, and we would mistakenly convert the finished transfer to no-op TRBs. Some kernel driver (maybe xHCI?) would then get stuck in an infinite loop in interrupt context, and the whole machine would hang. This patch should be backported to kernels as old as 3.4, that contain the commit b008df60 "xHCI: count free TRBs on transfer ring" Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Andiry Xu <andiry.xu@amd.com> Signed-off-by:
-
Stanislaw Ledwon authored
commit 8bea2bd3 upstream. The host controller port status register supports CAS (Cold Attach Status) bit. This bit could be set when USB3.0 device is connected when system is in Sx state. When the system wakes to S0 this port status with CAS bit is reported and this port can't be used by any device. When CAS bit is set the port should be reset by warm reset. This was not supported by xhci driver. The issue was found when pendrive was connected to suspended platform. The link state of "Compliance Mode" was reported together with CAS bit. This link state was also not supported by xhci and core/hub.c. The CAS bit is defined only for xhci root hub port and it is not supported on regular hubs. The link status is used to force warm reset on port. Make the USB core issue a warm reset when port is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver to report 'compliance mode' when the CAS is set. This force warm reset on the root hub port. This patch should be backported to stable kernels as old as 3.2, that contain the commit 10d674a8 "USB: When hot reset for USB3 fails, try warm reset." Signed-off-by:
Stanislaw Ledwon <staszek.ledwon@linux.intel.com> Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Signed-off-by:
-
Gaosen Zhang authored
commit aacef9c5 upstream. Signed-off-by:
Gaosen Zhang <gaosen.zhang@mediatek.com> Signed-off-by:
-
Bjørn Mork authored
commit 8e16e33c upstream. Switches into a composite device by ejecting the initial driver CD. The four interfaces are: QCDM, AT, QMI/wwan and mass storage. Let this driver manage the two serial interfaces: T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 28 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1402 Rev= 0.00 S: Manufacturer=ZTE,Incorporated S: Product=ZTE WCDMA Technologies MSM S: SerialNumber=xxxxx C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit b086b6b1 upstream. Clear the WDM_READ flag on empty reads to avoid running forever in an infinite tight loop, causing lockups: Jul 1 21:58:11 nemi kernel: [ 3658.898647] qmi_wwan 2-1:1.2: Unexpected error -71 Jul 1 21:58:36 nemi kernel: [ 3684.072021] BUG: soft lockup - CPU#0 stuck for 23s! [qmi.pl:12235] Jul 1 21:58:36 nemi kernel: [ 3684.072212] CPU 0 Jul 1 21:58:36 nemi kernel: [ 3684.072355] Jul 1 21:58:36 nemi kernel: [ 3684.072367] Pid: 12235, comm: qmi.pl Tainted: P O 3.5.0-rc2+ #13 LENOVO 2776LEG/2776LEG Jul 1 21:58:36 nemi kernel: [ 3684.072383] RIP: 0010:[<ffffffffa0635008>] [<ffffffffa0635008>] spin_unlock_irq+0x8/0xc [cdc_wdm] Jul 1 21:58:36 nemi kernel: [ 3684.072388] RSP: 0018:ffff88022dca1e70 EFLAGS: 00000282 Jul 1 21:58:36 nemi kernel: [ 3684.072393] RAX: ffff88022fc3f650 RBX: ffffffff811c56f7 RCX: 00000001000ce8c1 Jul 1 21:58:36 nemi kernel: [ 3684.072398] RDX: 0000000000000010 RSI: 000000000267d810 RDI: ffff88022fc3f650 Jul 1 21:58:36 nemi kernel: [ 3684.072403] RBP: ffff88022dca1eb0 R08: ffffffffa063578e R09: 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072407] R10: 0000000000000008 R11: 0000000000000246 R12: 0000000000000002 Jul 1 21:58:36 nemi kernel: [ 3684.072412] R13: 0000000000000246 R14: ffffffff00000002 R15: ffff8802281d8c88 Jul 1 21:58:36 nemi kernel: [ 3684.072418] FS: 00007f666a260700(0000) GS:ffff88023bc00000(0000) knlGS:0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072423] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Jul 1 21:58:36 nemi kernel: [ 3684.072428] CR2: 000000000270d9d8 CR3: 000000022e865000 CR4: 00000000000007f0 Jul 1 21:58:36 nemi kernel: [ 3684.072433] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072438] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Jul 1 21:58:36 nemi kernel: [ 3684.072444] Process qmi.pl (pid: 12235, threadinfo ffff88022dca0000, task ffff88022ff76380) Jul 1 21:58:36 nemi kernel: [ 3684.072448] Stack: Jul 1 21:58:36 nemi kernel: [ 3684.072458] ffffffffa063592e 0000000100020000 ffff88022fc3f650 ffff88022fc3f6a8 Jul 1 21:58:36 nemi kernel: [ 3684.072466] 0000000000000200 0000000100000000 000000000267d810 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072475] 0000000000000000 ffff880212cfb6d0 0000000000000200 ffff880212cfb6c0 Jul 1 21:58:36 nemi kernel: [ 3684.072479] Call Trace: Jul 1 21:58:36 nemi kernel: [ 3684.072489] [<ffffffffa063592e>] ? wdm_read+0x1a0/0x263 [cdc_wdm] Jul 1 21:58:36 nemi kernel: [ 3684.072500] [<ffffffff8110adb7>] ? vfs_read+0xa1/0xfb Jul 1 21:58:36 nemi kernel: [ 3684.072509] [<ffffffff81040589>] ? alarm_setitimer+0x35/0x64 Jul 1 21:58:36 nemi kernel: [ 3684.072517] [<ffffffff8110aec7>] ? sys_read+0x45/0x6e Jul 1 21:58:36 nemi kernel: [ 3684.072525] [<ffffffff813725f9>] ? system_call_fastpath+0x16/0x1b Jul 1 21:58:36 nemi kernel: [ 3684.072557] Code: <66> 66 90 c3 83 ff ed 89 f8 74 16 7f 06 83 ff a1 75 0a c3 83 ff f4 The WDM_READ flag is normally cleared by wdm_int_callback before resubmitting the read urb, and set by wdm_in_callback when this urb returns with data or an error. But a crashing device may cause both a read error and cancelling all urbs. Make sure that the flag is cleared by wdm_read if the buffer is empty. We don't clear the flag on errors, as there may be pending data in the buffer which should be processed. The flag will instead be cleared on the next wdm_read call. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Johan Hovold authored
commit b7d28e32 upstream. Do not set low_latency flag at open as tty_flip_buffer_push must not be called in IRQ context with low_latency set. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Jonathan Nieder authored
commit dc332fdf upstream. This is an old suspend/resume lockup fix: commit 2780cc46 Author: Len Brown <len.brown@intel.com> Date: Thu Dec 23 13:43:30 2004 -0500 [ACPI] Fix suspend/resume lockup issue by leaving Bus Master Arbitration enabled. The ACPI spec mandates it be disabled only for C3. http://bugzilla.kernel.org/show_bug.cgi?id=3599Signed-off-by:
David Shaohua Li <shaohua.li@intel.com> Signed-off-by:
Len Brown <len.brown@intel.com> The bug snuck back in in commit 2feec47d (ACPICA: ACPI 5: Support for new FADT SleepStatus, SleepControl registers, 2012-02-14), presumably by copy/pasting a copy of the code without that fix for the legacy case. On affected machines, after that commit, the machine locks up hard on resume from suspend. The same fix as seven years ago still works. Addresses <https://bugzilla.kernel.org/show_bug.cgi?id=43641>. Reported-bisected-and-tested-by:
Octavio Alvarez <alvarezp@alvarezp.com> Reported-by:
Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by:
Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
-
Dan Williams authored
commit 6ef1b512 upstream. fill_result_tf() grabs the taskfile flags from the originating qc which sas_ata_qc_fill_rtf() promptly overwrites. The presence of an ata_taskfile in the sata_device makes it tempting to just copy the full contents in sas_ata_qc_fill_rtf(). However, libata really only wants the fis contents and expects the other portions of the taskfile to not be touched by ->qc_fill_rtf. To that end store a fis buffer in the sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf() implementation. Reported-by:
Praveen Murali <pmurali@logicube.com> Tested-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Mark Rustad authored
commit 222a806a upstream. Avoid crashing if the private_data pointer happens to be NULL. This has been seen sometimes when a host reset happens, notably when there are many LUNs: host3: Assigned Port ID 0c1601 scsi host3: libfc: Host reset succeeded on port (0c1601) BUG: unable to handle kernel NULL pointer dereference at 0000000000000350 IP: [<ffffffff81352bb8>] scsi_send_eh_cmnd+0x58/0x3a0 <snip> Process scsi_eh_3 (pid: 4144, threadinfo ffff88030920c000, task ffff880326b160c0) Stack: 000000010372e6ba 0000000000000282 000027100920dca0 ffffffffa0038ee0 0000000000000000 0000000000030003 ffff88030920dc80 ffff88030920dc80 00000002000e0000 0000000a00004000 ffff8803242f7760 ffff88031326ed80 Call Trace: [<ffffffff8105b590>] ? lock_timer_base+0x70/0x70 [<ffffffff81352fbe>] scsi_eh_tur+0x3e/0xc0 [<ffffffff81353a36>] scsi_eh_test_devices+0x76/0x170 [<ffffffff81354125>] scsi_eh_host_reset+0x85/0x160 [<ffffffff81354291>] scsi_eh_ready_devs+0x91/0x110 [<ffffffff813543fd>] scsi_unjam_host+0xed/0x1f0 [<ffffffff813546a8>] scsi_error_handler+0x1a8/0x200 [<ffffffff81354500>] ? scsi_unjam_host+0x1f0/0x1f0 [<ffffffff8106ec3e>] kthread+0x9e/0xb0 [<ffffffff81509264>] kernel_thread_helper+0x4/0x10 [<ffffffff8106eba0>] ? kthread_freezable_should_stop+0x70/0x70 [<ffffffff81509260>] ? gs_change+0x13/0x13 Code: 25 28 00 00 00 48 89 45 c8 31 c0 48 8b 87 80 00 00 00 48 8d b5 60 ff ff ff 89 d1 48 89 fb 41 89 d6 4c 89 fa 48 8b 80 b8 00 00 00 <48> 8b 80 50 03 00 00 48 8b 00 48 89 85 38 ff ff ff 48 8b 07 4c RIP [<ffffffff81352bb8>] scsi_send_eh_cmnd+0x58/0x3a0 RSP <ffff88030920dc50> CR2: 0000000000000350 Signed-off-by:
Mark Rustad <mark.d.rustad@intel.com> Tested-by:
Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit dbe9a2ed upstream. The comparison between the system sleep state being entered and the lowest system sleep state the given device may wake up from in acpi_pm_device_sleep_state() is reversed, because the specification (ACPI 5.0) says that for wakeup to work: "The sleeping state being entered must be less than or equal to the power state declared in element 1 of the _PRW object." In other words, the state returned by _PRW is the deepest (lowest-power) system sleep state the device is capable of waking up the system from. Moreover, acpi_pm_device_sleep_state() also should check if the wakeup capability is supported through ACPI, because in principle it may be done via native PCIe PME, for example, in which case _SxW should not be evaluated. Signed-off-by:
-
Benjamin Tissoires authored
commit 3ac36d15 upstream. The previous implementation introduced a randomness in the splitting of the different touches reported by the device. This version is more robust as we don't rely on hi->input->absbit, but on our own structure. This also prepares hid-multitouch to better support Win8 devices. [Jiri Kosina <jkosina@suse.cz>: fix build] Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@enac.fr> Acked-by:
Henrik Rydberg <rydberg@euromail.se> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Bruce Allan authored
commit 470a5420 upstream. commit 44abd5c1 introduced NULL pointer dereferences when attempting to access the check_reset_block function pointer on 8257x and 80003es2lan non-copper devices. This fix should be applied back through 3.4. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by:
-
Tomi Valkeinen authored
commit 3568f2a4 upstream. There is a problem related to DSS FIFO thresholds and power management on OMAP3. It seems that when the full PM hits in, we get underflows. The core reason is unknown, but after experiments it looks like only particular FIFO thresholds work correctly. This bug is related to an earlier patch, which added special FIFO threshold configuration for OMAP3, because DSI command mode output didn't work with the normal threshold configuration. However, as the above work-around worked fine for other output types also, we currently always configure thresholds in this special way on OMAP3. In theory there should be negligible difference with this special way and the standard way. The first paragraph explains what happens in practice. This patch changes the driver to use the special threshold configuration only when the output is a manual update display on OMAP3. This does include RFBI displays also, and although it hasn't been tested (no boards using RFBI) I suspect the similar behaviour is present there also, as the DISPC side should work similarly for DSI command mode and RFBI. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Joe Woodward <jw@terrafix.co.uk> Signed-off-by:
-
Greg Pearson authored
commit 48c3b583 upstream. __alloc_memory_core_early() asks memblock for a range of memory then try to reserve it. If the reserved region array lacks space for the new range, memblock_double_array() is called to allocate more space for the array. If memblock is used to allocate memory for the new array it can end up using a range that overlaps with the range originally allocated in __alloc_memory_core_early(), leading to possible data corruption. With this patch memblock_double_array() now calls memblock_find_in_range() with a narrowed candidate range (in cases where the reserved.regions array is being doubled) so any memory allocated will not overlap with the original range that was being reserved. The range is narrowed by passing in the starting address and size of the previously allocated range. Then the range above the ending address is searched and if a candidate is not found, the range below the starting address is searched. Signed-off-by:
Greg Pearson <greg.pearson@hp.com> Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Acked-by:
Tejun Heo <tj@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Gavin Shan authored
commit 181eb394 upstream. The overall memblock has been organized into the memory regions and reserved regions. Initially, the memory regions and reserved regions are stored in the predetermined arrays of "struct memblock _region". It's possible for the arrays to be enlarged when we have newly added regions, but no free space left there. The policy here is to create double-sized array either by slab allocator or memblock allocator. Unfortunately, we didn't free the old array, which might be allocated through slab allocator before. That would cause memory leak. The patch introduces 2 variables to trace where (slab or memblock) the memory and reserved regions come from. The memory for the memory or reserved regions will be deallocated by kfree() if that was allocated by slab allocator. Thus to fix the memory leak issue. Signed-off-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
Gavin Shan authored
commit 4e2f0775 upstream. The overall memblock has been organized into the memory regions and reserved regions. Initially, the memory regions and reserved regions are stored in the predetermined arrays of "struct memblock _region". It's possible for the arrays to be enlarged when we have newly added regions for them, but no enough space there. Under the situation, We will created double-sized array to meet the requirement. However, the original implementation converted the VA (Virtual Address) of the newly allocated array of regions to PA (Physical Address), then translate back when we allocates the new array from slab. That's actually unnecessary. The patch removes the duplicate VA/PA conversion. Signed-off-by:
-
Tyler Hicks authored
commit 9fe79d76 upstream. If the first attempt at opening the lower file read/write fails, eCryptfs will retry using a privileged kthread. However, the privileged retry should not happen if the lower file's inode is read-only because a read/write open will still be unsuccessful. The check for determining if the open should be retried was intended to be based on the access mode of the lower file's open flags being O_RDONLY, but the check was incorrectly performed. This would cause the open to be retried by the privileged kthread, resulting in a second failed open of the lower file. This patch corrects the check to determine if the open request should be handled by the privileged kthread. Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Tyler Hicks authored
commit 60d65f1f upstream. Don't grab the daemon mutex while holding the message context mutex. Addresses this lockdep warning: ecryptfsd/2141 is trying to acquire lock: (&ecryptfs_msg_ctx_arr[i].mux){+.+.+.}, at: [<ffffffffa029c213>] ecryptfs_miscdev_read+0x143/0x470 [ecryptfs] but task is already holding lock: (&(*daemon)->mux){+.+...}, at: [<ffffffffa029c2ec>] ecryptfs_miscdev_read+0x21c/0x470 [ecryptfs] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(*daemon)->mux){+.+...}: [<ffffffff810a3b8d>] lock_acquire+0x9d/0x220 [<ffffffff8151c6da>] __mutex_lock_common+0x5a/0x4b0 [<ffffffff8151cc64>] mutex_lock_nested+0x44/0x50 [<ffffffffa029c5d7>] ecryptfs_send_miscdev+0x97/0x120 [ecryptfs] [<ffffffffa029b744>] ecryptfs_send_message+0x134/0x1e0 [ecryptfs] [<ffffffffa029a24e>] ecryptfs_generate_key_packet_set+0x2fe/0xa80 [ecryptfs] [<ffffffffa02960f8>] ecryptfs_write_metadata+0x108/0x250 [ecryptfs] [<ffffffffa0290f80>] ecryptfs_create+0x130/0x250 [ecryptfs] [<ffffffff811963a4>] vfs_create+0xb4/0x120 [<ffffffff81197865>] do_last+0x8c5/0xa10 [<ffffffff811998f9>] path_openat+0xd9/0x460 [<ffffffff81199da2>] do_filp_open+0x42/0xa0 [<ffffffff81187998>] do_sys_open+0xf8/0x1d0 [<ffffffff81187a91>] sys_open+0x21/0x30 [<ffffffff81527d69>] system_call_fastpath+0x16/0x1b -> #0 (&ecryptfs_msg_ctx_arr[i].mux){+.+.+.}: [<ffffffff810a3418>] __lock_acquire+0x1bf8/0x1c50 [<ffffffff810a3b8d>] lock_acquire+0x9d/0x220 [<ffffffff8151c6da>] __mutex_lock_common+0x5a/0x4b0 [<ffffffff8151cc64>] mutex_lock_nested+0x44/0x50 [<ffffffffa029c213>] ecryptfs_miscdev_read+0x143/0x470 [ecryptfs] [<ffffffff811887d3>] vfs_read+0xb3/0x180 [<ffffffff811888ed>] sys_read+0x4d/0x90 [<ffffffff81527d69>] system_call_fastpath+0x16/0x1b Signed-off-by:
-
Tyler Hicks authored
commit 8dc67805 upstream. File operations on /dev/ecryptfs would BUG() when the operations were performed by processes other than the process that originally opened the file. This could happen with open files inherited after fork() or file descriptors passed through IPC mechanisms. Rather than calling BUG(), an error code can be safely returned in most situations. In ecryptfs_miscdev_release(), eCryptfs still needs to handle the release even if the last file reference is being held by a process that didn't originally open the file. ecryptfs_find_daemon_by_euid() will not be successful, so a pointer to the daemon is stored in the file's private_data. The private_data pointer is initialized when the miscdev file is opened and only used when the file is released. https://launchpad.net/bugs/994247Signed-off-by:
Sasha Levin <levinsasha928@gmail.com> Tested-by:
-
Mike Snitzer authored
commit b0239faa upstream. If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a sufficiently-large metadata device is used in a thin pool then the space map checker will fail to allocate the memory it requires. Switch from kmalloc to vmalloc to allow larger virtually contiguous allocations for the space map checker's internal count arrays. Reported-by:
Vivek Goyal <vgoyal@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 62662303 upstream. If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create() fails, dm_tm_create_internal() would still return success even though it cleaned up all resources it was supposed to have created. This will lead to a kernel crash: general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC ... RIP: 0010:[<ffffffff81593659>] [<ffffffff81593659>] dm_bufio_get_block_size+0x9/0x20 Call Trace: [<ffffffff81599bae>] dm_bm_block_size+0xe/0x10 [<ffffffff8159b8b8>] sm_ll_init+0x78/0xd0 [<ffffffff8159c1a6>] sm_ll_new_disk+0x16/0xa0 [<ffffffff8159c98e>] dm_sm_disk_create+0xfe/0x160 [<ffffffff815abf6e>] dm_pool_metadata_open+0x16e/0x6a0 [<ffffffff815aa010>] pool_ctr+0x3f0/0x900 [<ffffffff8158d565>] dm_table_add_target+0x195/0x450 [<ffffffff815904c4>] table_load+0xe4/0x330 [<ffffffff815917ea>] ctl_ioctl+0x15a/0x2c0 [<ffffffff81591963>] dm_ctl_ioctl+0x13/0x20 [<ffffffff8116a4f8>] do_vfs_ioctl+0x98/0x560 [<ffffffff8116aa51>] sys_ioctl+0x91/0xa0 [<ffffffff81869f52>] system_call_fastpath+0x16/0x1b Fix the space map checker code to return an appropriate ERR_PTR and have dm_sm_disk_create() and dm_tm_create_internal() check for it with IS_ERR. Reported-by:
-
Mike Snitzer authored
commit 25d7cd6f upstream. Cleanup the shadow table before destroying the transaction manager. Reference: leak was identified with kmemleak when running test_discard_random_sectors in the thinp-test-suite. Signed-off-by:
-
Milan Broz authored
commit 18068bdd upstream. Veritysetup is now part of cryptsetup package. Remove on-disk header description (which is not parsed in kernel) and point users to cryptsetup where it the format is documented. Mention units for block size paramaters. Fix target line specification and dmsetup parameters. Signed-off-by:
Milan Broz <mbroz@redhat.com> Signed-off-by:
-
majianpeng authored
commit 1850753d upstream. In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement nr_pending so we lose the reference we hold on the rdev. So atomic_inc it first to maintain the reference. This bug was introduced by commit 73e92e51 md/raid5. Don't write to known bad block on doubtful devices. which appeared in 3.0, so patch is suitable for stable kernels since then. Signed-off-by:
majianpeng <majianpeng@gmail.com> Signed-off-by:
-
NeilBrown authored
commit 055d3747 upstream. commit 58c54fcc md/raid10: handle further errors during fix_read_error better. in 3.1 added "r10_sync_page_io" which takes an IO size in sectors. But we were passing the IO size in bytes!!! This resulting in bio_add_page failing, and empty request being sent down, and a consequent BUG_ON in scsi_lib. [fix missing space in error message at same time] This fix is suitable for 3.1.y and later. Reported-by:
Christian Balzer <chibi@gol.com> Signed-off-by:
-
