- 09 Dec, 2015 40 commits
-
-
Greg Kroah-Hartman authored
-
Herbert Xu authored
The backport of 1f770c0a ("netlink: Fix autobind race condition that leads to zero port ID") missed a goto statement, which causes netlink to break subtly. This was discovered by Stefan Priebe <s.priebe@profihost.ag>. Fixes: 4e277624 ("netlink: Fix autobind race condition that...") Reported-by:
Stefan Priebe <s.priebe@profihost.ag> Reported-by:
Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Hildenbrand authored
commit 5967c17b upstream. We should never allow to enable/disable any facilities for the guest when other VCPUs were already created. kvm_arch_vcpu_(load|put) relies on SIMD not changing during runtime. If somebody would create and run VCPUs and then decides to enable SIMD, undefined behaviour could be possible (e.g. vector save area not being set up). Acked-by:
Christian Borntraeger <borntraeger@de.ibm.com> Acked-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by:
-
Arnd Bergmann authored
commit 9f088dba upstream. The recently introduced lnet_peer_set_alive() function uses get_seconds() to read the current time into a shared variable, but all other uses of that variable compare it to jiffies values. This changes the current use to jiffies as well for consistency. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: af3fa7c7 ("staging/lustre/lnet: peer aliveness status and NI status") Cc: Liang Zhen <liang.zhen@intel.com> Cc: James Simmons <uja.ornl@gmail.com> Cc: Isaac Huang <he.huang@intel.com> Signed-off-by:
Oleg Drokin <oleg.drokin@intel.com> Signed-off-by:
-
Rajmohan Mani authored
commit a5964396 upstream. Existing Intel xHCI controllers require a delay of 1 mS, after setting the CMD_RESET bit in command register, before accessing any HC registers. This allows the HC to complete the reset operation and be ready for HC register access. Without this delay, the subsequent HC register access, may result in a system hang, very rarely. Verified CherryView / Braswell platforms go through over 5000 warm reboot cycles (which was not possible without this patch), without any xHCI reset hang. Signed-off-by:
Rajmohan Mani <rajmohan.mani@intel.com> Tested-by:
Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Peter Hurley authored
commit ee0c1a65 upstream. The correct lock order is atomic_write_lock => termios_rwsem, as established by tty_write() => n_tty_write(). Fixes: c274f6ef ("tty: Hold termios_rwsem for tcflow(TCIxxx)") Reported-and-Tested-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Peter Hurley authored
commit 6b2a3d62 upstream. The data to audit/record is in the 'from' buffer (ie., the input read buffer). Fixes: 72586c60 ("n_tty: Fix auditing support for cannonical mode") Cc: Miloslav Trmač <mitr@redhat.com> Signed-off-by:
Laura Abbott <labbott@fedoraproject.org> Signed-off-by:
-
Clemens Ladisch authored
commit a91e627e upstream. One of the many faults of the QinHeng CH345 USB MIDI interface chip is that it does not handle received SysEx messages correctly -- every second event packet has a wrong code index number, which is the one from the last seen message, instead of 4. For example, the two messages "FE F0 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event packets: correct: CH345: 0F FE 00 00 0F FE 00 00 04 F0 01 02 04 F0 01 02 04 03 04 05 0F 03 04 05 04 06 07 08 04 06 07 08 04 09 0A 0B 0F 09 0A 0B 04 0C 0D 0E 04 0C 0D 0E 05 F7 00 00 05 F7 00 00 A class-compliant driver must interpret an event packet with CIN 15 as having a single data byte, so the other two bytes would be ignored. The message received by the host would then be missing two bytes out of six; in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7". These corrupted SysEx event packages contain only data bytes, while the CH345 uses event packets with a correct CIN value only for messages with a status byte, so it is possible to distinguish between these two cases by checking for the presence of this status byte. (Other bugs in the CH345's input handling, such as the corruption resulting from running status, cannot be worked around.) Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Clemens Ladisch authored
commit 1ca8b201 upstream. The CH345 USB MIDI chip has two output ports. However, they are multiplexed through one pin, and the number of ports cannot be reduced even for hardware that implements only one connector, so for those devices, data sent to either port ends up on the same hardware output. This becomes a problem when both ports are used at the same time, as longer MIDI commands (such as SysEx messages) are likely to be interrupted by messages from the other port, and thus to get lost. It would not be possible for the driver to detect how many ports the device actually has, except that in practice, _all_ devices built with the CH345 have only one port. So we can just ignore the device's descriptors, and hardcode one output port. Signed-off-by:
-
Clemens Ladisch authored
commit 98d362be upstream. Signed-off-by:
-
Bjørn Mork authored
commit 638148e2 upstream. Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Aleksander Morgado authored
commit e07af133 upstream. Also known as Verizon U620L. The device is modeswitched from 1410:9020 to 1410:9022 by selecting the 4th USB configuration: $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4 This configuration provides a ECM interface as well as TTYs ('Enterprise Mode' according to the U620 Linux integration guide). Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
David Woodhouse authored
commit 1bcb49e6 upstream. The Honeywell HGI80 is a wireless interface to the evohome connected thermostat. It uses a TI 3410 USB-serial port. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 705e63d2 upstream. There is a bit of a mess in the order of arguments to the ulpi write callback. There is int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val) in drivers/usb/common/ulpi.c; struct usb_phy_io_ops { ... int (*write)(struct usb_phy *x, u32 val, u32 reg); } in include/linux/usb/phy.h. The callback registered by the musb driver has to comply to the latter, but up to now had "offset" first which effectively made the function broken for correct users. So flip the order and while at it also switch to the parameter names of struct usb_phy_io_ops's write. Fixes: ffb865b1 ("usb: musb: add ulpi access operations") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Bjørn Mork authored
commit 59536da3 upstream. The DEVICE_HWI type was added under the faulty assumption that Huawei devices based on Qualcomm chipsets and firmware use the static USB interface numbering known from Gobi devices. But this model does not apply to Huawei devices like the HP branded lt4112 (Huawei me906e). Huawei firmwares will dynamically assign interface numbers. Functions are renumbered when the firmware is reconfigured. Fix by changing the DEVICE_HWI type to use a simplified version of Huawei's subclass + protocol scheme: Blacklisting known network interface combinations and assuming the rest are serial. Reported-and-tested-by:
Muri Nicanor <muri+libqmi@immerda.ch> Tested-by:
Martin Hauke <mardnh@gmx.de> Fixes: e7181d00 ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem") Signed-off-by:
-
Petr Štetiar authored
commit 9d5b5ed7 upstream. It seems like this device has same vendor and product IDs as G2K devices, but it has different number of interfaces(4 vs 5) and also different interface layout which makes it currently unusable: usbcore: registered new interface driver qcserial usbserial: USB Serial support registered for Qualcomm USB modem usb 2-1.2: unknown number of interfaces: 5 lsusb output: Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05c6 Qualcomm, Inc. idProduct 0x9215 Acer Gobi 2000 Wireless Modem bcdDevice 2.32 iManufacturer 1 Quectel iProduct 2 Quectel LTE Module iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 209 bNumInterfaces 5 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 500mA Signed-off-by:
Petr Štetiar <ynezz@true.cz> [johan: rename define and add comment ] Signed-off-by:
-
Jiri Slaby authored
commit 19cd80a2 upstream. It is not permitted to set task state before lock. usblp_wwait sets the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible. Upon return from that function, the state will be TASK_RUNNING again. This is clearly a bug and a warning is generated with LOCKDEP too: WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp] Modules linked in: ... CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1 Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508 Call Trace: ... [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp] [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp] [<ffffffff8121ed98>] __vfs_write+0x28/0xf0 ... Commit 7f477358 (usblp: Implement the ENOSPC convention) moved the set prior locking. So move it back after the lock. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Fixes: 7f477358 ("usblp: Implement the ENOSPC convention") Acked-By:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
Jonas Gorski authored
commit db1319e1 upstream. Commit d445913c ("usb: ehci-orion: add optional PHY support") added support for optional phys, but devm_phy_optional_get returns -ENOSYS if GENERIC_PHY is not enabled. This causes probe failures, even when there are no phys specified: [ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38 [ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38 Similar to dwc3, treat -ENOSYS as no phy. Fixes: d445913c ("usb: ehci-orion: add optional PHY support") Signed-off-by:
Jonas Gorski <jogo@openwrt.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Jurgen Kramer authored
commit 16771c7c upstream. This patch adds native DSD support for the Aune X1S 32BIT/384 DSD DAC Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Signed-off-by:
-
Peter Chen authored
commit ae3e57ae upstream. Some i.mx platforms need three clocks to let controller work, but others only need one, refine clock operation to adapt for all platforms, it fixes a regression found at i.mx27. Signed-off-by:
Peter Chen <peter.chen@freescale.com> Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
John Youn authored
commit bb7f3d6d upstream. Add platform data and set usb3_lpm_capable and has_lpm_erratum. Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
John Youn authored
commit 690fb371 upstream. This patch allows the dwc3 driver to run on the new Synopsys USB 3.1 IP core, albeit in USB 3.0 mode only. The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register interface and programming model as the existing USB 3.0 controller IP (DWC_usb3). However the GSNPSID and version numbers are different. Add checking for the new ID to pass driver probe. Also, since the DWC_usb31 version number is lower in value than the full GSNPSID of the DWC_usb3 IP, we set the high bit to identify DWC_usb31 and to ensure the values are higher. Finally, add a documentation note about the revision numbering scheme. Any future revision checks (for STARS, workarounds, and new features) should take into consideration how it applies to both the 3.1/3.0 IP. Signed-off-by:
-
John Youn authored
commit e8095a25 upstream. This adds the PCI product ID for the Synopsys USB 3.1 IP core (DWC_usb31) on a HAPS-based PCI development platform. Signed-off-by:
-
John Youn authored
commit 41adc59c upstream. This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe HAPS platform. This core has the debug registers mapped at a separate BAR in order to support enhanced hibernation. Signed-off-by:
-
Li Jun authored
commit 85da852d upstream. This patch is to support load and unload gadget driver in full OTG mode. Signed-off-by:
Li Jun <jun.li@freescale.com> Signed-off-by:
Jiada Wang <jiada_wang@mentor.com> Signed-off-by:
-
Ben McCauley authored
commit b9e51b2b upstream. In some SoCs, dwc3 is implemented as a USB2.0 only core, meaning that it can't ever achieve SuperSpeed. Currect driver always sets gadget.max_speed to USB_SPEED_SUPER unconditionally. This can causes issues to some Host stacks where the host will issue a GetBOS() request and we will reply with a BOS containing Superspeed Capability Descriptor. At least Windows seems to be upset by this fact and prints a warning that we should connect $this device to another port. [ balbi@ti.com : rewrote entire commit, including source code comment to make a lot clearer what the problem is ] Signed-off-by:
Ben McCauley <ben.mccauley@garmin.com> Signed-off-by:
-
Douglas Gilbert authored
commit d134c48d upstream. Following changes that appeared in lk 4.0.0, the gadget udc driver for some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families) incorrectly deduced full-speed USB link speed even when the hardware had negotiated a high-speed link. The fix is to make sure that the UDPHS Interrupt Enable Register value does not mask the SPEED bit in the Interrupt Status Register. For a mass storage gadget this problem lead to failures when the host had a USB 3 port with the xhci_hcd driver. If the host was a USB 2 port using the ehci_hcd driver then the mass storage gadget worked (but probably at a lower speed than it should have). Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: 9870d895 ("usb: atmel_usba_udc: Mask status with enabled irqs") Signed-off-by:
-
Ville Syrjälä authored
commit d115d705 upstream. This reverts commit 8f2c9544. As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out fine, but after a bit of data has been transferred it just stops flowing. Note that I do get a bunch of these "NOHZ: local_softirq_pending 08" when booting the machine, but I'm not really sure if they're related to this problem. Cc: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
David Hildenbrand authored
commit b85de33a upstream. Commit 383d0b05 ("KVM: s390: handle pending local interrupts via bitmap") introduced a possible memory overwrite from user space. User space could pass an invalid emergency signal code (sending VCPU) and therefore exceed the bitmap. Let's take care of this case and check that the id is in the valid range. Reviewed-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by:
-
David Hildenbrand authored
commit 152e9f65 upstream. For now, VCPUs were always created sequentially with incrementing VCPU ids. Therefore, the index in the VCPUs array matched the id. As sequential creation might change with cpu hotplug, let's use the correct lookup function to find a VCPU by id, not array index. Let's also use kvm_lookup_vcpu() for validation of the sending VCPU on external call injection. Reviewed-by:
-
David Hildenbrand authored
commit db27a7a3 upstream. Let's provide a function to lookup a VCPU by id. Reviewed-by:
-
David Hildenbrand authored
commit c5c2c393 upstream. We seemed to have missed a few corner cases in commit f6c137ff ("KVM: s390: randomize sca address"). The SCA has a maximum size of 2112 bytes. By setting the sca_offset to some unlucky numbers, we exceed the page. 0x7c0 (1984) -> Fits exactly 0x7d0 (2000) -> 16 bytes out 0x7e0 (2016) -> 32 bytes out 0x7f0 (2032) -> 48 bytes out One VCPU entry is 32 bytes long. For the last two cases, we actually write data to the other page. 1. The address of the VCPU. 2. Injection/delivery/clearing of SIGP externall calls via SIGP IF. Especially the 2. happens regularly. So this could produce two problems: 1. The guest losing/getting external calls. 2. Random memory overwrites in the host. So this problem happens on every 127 + 128 created VM with 64 VCPUs. Acked-by:
-
Rajkumar Manoharan authored
commit f680f70a upstream. The number of spatial streams that are derived from chain mask for 4x4 devices is using wrong bitmask and conditional check. This is affecting downlink throughput for QCA99x0 devices. Earlier cfg_tx_chainmask is not filled by default until user configured it and so get_nss_from_chainmask never be called. This issue is exposed by recent commit 166de3f1 ("ath10k: remove supported chain mask"). By default maximum supported chain mask is filled in cfg_tx_chainmask. Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation") Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Mark Rutland authored
commit cb083816 upstream. A kernel built with DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA doesn't have .text aligned to a page boundary, though fixup_executable works at page-granularity thanks to its use of create_mapping. If .text is not page-aligned, the first page it exists in may be marked non-executable, leading to failures when an attempt is made to execute code in said page. This patch upgrades ALIGN_DEBUG_RO and ALIGN_DEBUG_RO_MIN to force page alignment for DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA kernels, ensuring that all sections with specific RWX permission requirements are mapped with the correct permissions. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Reported-by:
Jeremy Linton <jeremy.linton@arm.com> Reviewed-by:
Laura Abbott <laura@labbott.name> Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Suzuki Poulose <suzuki.poulose@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: da141706 ("arm64: add better page protections to arm64") Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Robin Murphy authored
commit 5accd17d upstream. For reasons not entirely apparent, but now enshrined in history, the architectural mapping of AArch32 banked registers to AArch64 registers actually orders SP_<mode> and LR_<mode> backwards compared to the intuitive r13/r14 order, for all modes except FIQ. Fix the compat_<reg>_<mode> macros accordingly, in the hope of avoiding subtle bugs with KVM and AArch32 guests. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Mirza Krak authored
commit 7cecd9ab upstream. According to SJA1000 data sheet error-warning (EI) interrupt is not cleared by setting the controller in to reset-mode. Then if we have the following case: - system is suspended (echo mem > /sys/power/state) and SJA1000 is left in operating state - A bus error condition occurs which activates EI interrupt, system is still suspended which means EI interrupt will be not be handled nor cleared. If the above two events occur, on resume there is no way to return the SJA1000 to operating state, except to cycle power to it. By simply reading the IR register on start we will clear any previous conditions that could be present. Signed-off-by:
Mirza Krak <mirza.krak@hostmobility.com> Reported-by:
Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Marek Vasut authored
commit 562b103a upstream. The sizeof() is invoked on an incorrect variable, likely due to some copy-paste error, and this might result in memory corruption. Fix this. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: netdev@vger.kernel.org Signed-off-by:
-
Johan Hedberg authored
commit a6ad2a6b upstream. The commit 89cbb063 introduced support for deferred connection parameter removal when unpairing by removing them only once an existing connection gets disconnected. However, it failed to address the scenario when we're *not* connected and do an unpair operation. What makes things worse is that most user space BlueZ versions will first issue a disconnect request and only then unpair, meaning the buggy code will be triggered every time. This effectively causes the kernel to resume scanning and reconnect to a device for which we've removed all keys and GATT database information. This patch fixes the issue by adding the missing call to the hci_conn_params_del() function to a branch which handles the case of no existing connection. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Dmitry Tunin authored
commit 18e0afab upstream. T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=817b Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1506615Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Dmitry Tunin authored
commit cd355ff0 upstream. This adapter works with the existing linux-firmware. T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=021c Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1502781Signed-off-by:
-
