Merge branches 'clk-iproc', 'clk-mvebu' and 'clk-qcom-a53' into clk-next

* clk-iproc:
  clk: iproc: Minor tidy up of iproc pll data structures
  clk: iproc: Allow plls to do minor rate changes without reset
  clk: iproc: Fix error in the pll post divider rate calculation
  clk: iproc: Allow iproc pll to runtime calculate vco parameters

* clk-mvebu:
  clk: mvebu: armada-37xx-periph: Use PTR_ERR_OR_ZERO()

* clk-qcom-a53:
  clk: qcom: Add APCS clock controller support
  clk: qcom: Add regmap mux-div clocks support
  clk: qcom: Add A53 PLL support

Documentation/devicetree/bindings/clock/qcom,a53pll.txt

+Qualcomm MSM8916 A53 PLL Binding
+--------------------------------
+The A53 PLL on MSM8916 platforms is the main CPU PLL used used for frequencies
+above 1GHz.
+
+Required properties :
+- compatible : Shall contain only one of the following:
+
+		"qcom,msm8916-a53pll"
+
+- reg : shall contain base register location and length
+
+- #clock-cells : must be set to <0>
+
+Example:
+
+	a53pll: clock@b016000 {
+		compatible = "qcom,msm8916-a53pll";
+		reg = <0xb016000 0x40>;
+		#clock-cells = <0>;
+	};
+

drivers/clk/bcm/clk-cygnus.c

@@ -269,23 +269,10 @@ static void __init cygnus_asiu_init(struct device_node *node)
 }
 CLK_OF_DECLARE(cygnus_asiu_clk, "brcm,cygnus-asiu-clk", cygnus_asiu_init);
 
-/*
- * AUDIO PLL VCO frequency parameter table
- *
- * PLL output frequency = ((ndiv_int + ndiv_frac / 2^20) *
- * (parent clock rate / pdiv)
- *
- * On Cygnus, parent is the 25MHz oscillator
- */
-static const struct iproc_pll_vco_param audiopll_vco_params[] = {
-	/* rate (Hz) ndiv_int ndiv_frac pdiv */
-	{ 1354750204UL,  54,     199238,   1 },
-	{ 1769470191UL,  70,     816639,   1 },
-};
-
 static const struct iproc_pll_ctrl audiopll = {
 	.flags = IPROC_CLK_PLL_NEEDS_SW_CFG | IPROC_CLK_PLL_HAS_NDIV_FRAC |
-		IPROC_CLK_PLL_USER_MODE_ON | IPROC_CLK_PLL_RESET_ACTIVE_LOW,
+		IPROC_CLK_PLL_USER_MODE_ON | IPROC_CLK_PLL_RESET_ACTIVE_LOW |
+		IPROC_CLK_PLL_CALC_PARAM,
 	.reset = RESET_VAL(0x5c, 0, 1),
 	.dig_filter = DF_VAL(0x48, 0, 3, 6, 4, 3, 3),
 	.sw_ctrl = SW_CTRL_VAL(0x4, 0),
@@ -300,8 +287,7 @@ static const struct iproc_pll_ctrl audiopll = {
 static const struct iproc_clk_ctrl audiopll_clk[] = {
 	[BCM_CYGNUS_AUDIOPLL_CH0] = {
 		.channel = BCM_CYGNUS_AUDIOPLL_CH0,
-		.flags = IPROC_CLK_AON |
-				IPROC_CLK_MCLK_DIV_BY_2,
+		.flags = IPROC_CLK_AON | IPROC_CLK_MCLK_DIV_BY_2,
 		.enable = ENABLE_VAL(0x14, 8, 10, 9),
 		.mdiv = REG_VAL(0x14, 0, 8),
 	},
@@ -321,9 +307,8 @@ static const struct iproc_clk_ctrl audiopll_clk[] = {
 
 static void __init cygnus_audiopll_clk_init(struct device_node *node)
 {
-	iproc_pll_clk_setup(node, &audiopll, audiopll_vco_params,
-			    ARRAY_SIZE(audiopll_vco_params), audiopll_clk,
-			    ARRAY_SIZE(audiopll_clk));
+	iproc_pll_clk_setup(node, &audiopll, NULL, 0,
+			    audiopll_clk,  ARRAY_SIZE(audiopll_clk));
 }
 CLK_OF_DECLARE(cygnus_audiopll, "brcm,cygnus-audiopll",
 			cygnus_audiopll_clk_init);

drivers/clk/bcm/clk-iproc.h

@@ -80,6 +80,11 @@
  */
 #define IPROC_CLK_PLL_RESET_ACTIVE_LOW BIT(9)
 
+/*
+ * Calculate the PLL parameters are runtime, instead of using table
+ */
+#define IPROC_CLK_PLL_CALC_PARAM BIT(10)
+
 /*
  * Parameters for VCO frequency configuration
  *

drivers/clk/mvebu/armada-37xx-periph.c

@@ -638,10 +638,7 @@ static int armada_3700_add_composite_clk(const struct clk_periph_data *data,
 					mux_ops, rate_hw, rate_ops,
 					gate_hw, gate_ops, CLK_IGNORE_UNUSED);
 
-	if (IS_ERR(*hw))
-		return PTR_ERR(*hw);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(*hw);
 }
 
 static int armada_3700_periph_clock_probe(struct platform_device *pdev)

drivers/clk/qcom/Kconfig

@@ -12,6 +12,27 @@ config COMMON_CLK_QCOM
 	select REGMAP_MMIO
 	select RESET_CONTROLLER
 
+config QCOM_A53PLL
+	tristate "MSM8916 A53 PLL"
+	depends on COMMON_CLK_QCOM
+	default ARCH_QCOM
+	help
+	  Support for the A53 PLL on MSM8916 devices. It provides
+	  the CPU with frequencies above 1GHz.
+	  Say Y if you want to support higher CPU frequencies on MSM8916
+	  devices.
+
+config QCOM_CLK_APCS_MSM8916
+	tristate "MSM8916 APCS Clock Controller"
+	depends on COMMON_CLK_QCOM
+	depends on QCOM_APCS_IPC || COMPILE_TEST
+	default ARCH_QCOM
+	help
+	  Support for the APCS Clock Controller on msm8916 devices. The
+	  APCS is managing the mux and divider which feeds the CPUs.
+	  Say Y if you want to support CPU frequency scaling on devices
+	  such as msm8916.
+
 config QCOM_CLK_RPM
 	tristate "RPM based Clock Controller"
 	depends on COMMON_CLK_QCOM && MFD_QCOM_RPM

drivers/clk/qcom/Makefile

@@ -10,6 +10,7 @@ clk-qcom-y += clk-rcg2.o
 clk-qcom-y += clk-branch.o
 clk-qcom-y += clk-regmap-divider.o
 clk-qcom-y += clk-regmap-mux.o
+clk-qcom-y += clk-regmap-mux-div.o
 clk-qcom-y += reset.o
 clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o
 
@@ -32,6 +33,8 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm8960.o
 obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
 obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
 obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
+obj-$(CONFIG_QCOM_A53PLL) += a53-pll.o
+obj-$(CONFIG_QCOM_CLK_APCS_MSM8916) += apcs-msm8916.o
 obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
 obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
 obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o

drivers/clk/qcom/a53-pll.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Qualcomm A53 PLL driver
+ *
+ * Copyright (c) 2017, Linaro Limited
+ * Author: Georgi Djakov <georgi.djakov@linaro.org>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/module.h>
+
+#include "clk-pll.h"
+#include "clk-regmap.h"
+
+static const struct pll_freq_tbl a53pll_freq[] = {
+	{  998400000, 52, 0x0, 0x1, 0 },
+	{ 1094400000, 57, 0x0, 0x1, 0 },
+	{ 1152000000, 62, 0x0, 0x1, 0 },
+	{ 1209600000, 63, 0x0, 0x1, 0 },
+	{ 1248000000, 65, 0x0, 0x1, 0 },
+	{ 1363200000, 71, 0x0, 0x1, 0 },
+	{ 1401600000, 73, 0x0, 0x1, 0 },
+	{ }
+};
+
+static const struct regmap_config a53pll_regmap_config = {
+	.reg_bits		= 32,
+	.reg_stride		= 4,
+	.val_bits		= 32,
+	.max_register		= 0x40,
+	.fast_io		= true,
+};
+
+static int qcom_a53pll_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct regmap *regmap;
+	struct resource *res;
+	struct clk_pll *pll;
+	void __iomem *base;
+	struct clk_init_data init = { };
+	int ret;
+
+	pll = devm_kzalloc(dev, sizeof(*pll), GFP_KERNEL);
+	if (!pll)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	regmap = devm_regmap_init_mmio(dev, base, &a53pll_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	pll->l_reg = 0x04;
+	pll->m_reg = 0x08;
+	pll->n_reg = 0x0c;
+	pll->config_reg = 0x14;
+	pll->mode_reg = 0x00;
+	pll->status_reg = 0x1c;
+	pll->status_bit = 16;
+	pll->freq_tbl = a53pll_freq;
+
+	init.name = "a53pll";
+	init.parent_names = (const char *[]){ "xo" };
+	init.num_parents = 1;
+	init.ops = &clk_pll_sr2_ops;
+	init.flags = CLK_IS_CRITICAL;
+	pll->clkr.hw.init = &init;
+
+	ret = devm_clk_register_regmap(dev, &pll->clkr);
+	if (ret) {
+		dev_err(dev, "failed to register regmap clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get,
+					  &pll->clkr.hw);
+	if (ret) {
+		dev_err(dev, "failed to add clock provider: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id qcom_a53pll_match_table[] = {
+	{ .compatible = "qcom,msm8916-a53pll" },
+	{ }
+};
+
+static struct platform_driver qcom_a53pll_driver = {
+	.probe = qcom_a53pll_probe,
+	.driver = {
+		.name = "qcom-a53pll",
+		.of_match_table = qcom_a53pll_match_table,
+	},
+};
+module_platform_driver(qcom_a53pll_driver);
+
+MODULE_DESCRIPTION("Qualcomm A53 PLL Driver");
+MODULE_LICENSE("GPL v2");

drivers/clk/qcom/apcs-msm8916.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Qualcomm APCS clock controller driver
+ *
+ * Copyright (c) 2017, Linaro Limited
+ * Author: Georgi Djakov <georgi.djakov@linaro.org>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "clk-regmap.h"
+#include "clk-regmap-mux-div.h"
+
+static const u32 gpll0_a53cc_map[] = { 4, 5 };
+
+static const char * const gpll0_a53cc[] = {
+	"gpll0_vote",
+	"a53pll",
+};
+
+/*
+ * We use the notifier function for switching to a temporary safe configuration
+ * (mux and divider), while the A53 PLL is reconfigured.
+ */
+static int a53cc_notifier_cb(struct notifier_block *nb, unsigned long event,
+			     void *data)
+{
+	int ret = 0;
+	struct clk_regmap_mux_div *md = container_of(nb,
+						     struct clk_regmap_mux_div,
+						     clk_nb);
+	if (event == PRE_RATE_CHANGE)
+		/* set the mux and divider to safe frequency (400mhz) */
+		ret = mux_div_set_src_div(md, 4, 3);
+
+	return notifier_from_errno(ret);
+}
+
+static int qcom_apcs_msm8916_clk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device *parent = dev->parent;
+	struct clk_regmap_mux_div *a53cc;
+	struct regmap *regmap;
+	struct clk_init_data init = { };
+	int ret;
+
+	regmap = dev_get_regmap(parent, NULL);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(dev, "failed to get regmap: %d\n", ret);
+		return ret;
+	}
+
+	a53cc = devm_kzalloc(dev, sizeof(*a53cc), GFP_KERNEL);
+	if (!a53cc)
+		return -ENOMEM;
+
+	init.name = "a53mux";
+	init.parent_names = gpll0_a53cc;
+	init.num_parents = ARRAY_SIZE(gpll0_a53cc);
+	init.ops = &clk_regmap_mux_div_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+
+	a53cc->clkr.hw.init = &init;
+	a53cc->clkr.regmap = regmap;
+	a53cc->reg_offset = 0x50;
+	a53cc->hid_width = 5;
+	a53cc->hid_shift = 0;
+	a53cc->src_width = 3;
+	a53cc->src_shift = 8;
+	a53cc->parent_map = gpll0_a53cc_map;
+
+	a53cc->pclk = devm_clk_get(parent, NULL);
+	if (IS_ERR(a53cc->pclk)) {
+		ret = PTR_ERR(a53cc->pclk);
+		dev_err(dev, "failed to get clk: %d\n", ret);
+		return ret;
+	}
+
+	a53cc->clk_nb.notifier_call = a53cc_notifier_cb;
+	ret = clk_notifier_register(a53cc->pclk, &a53cc->clk_nb);
+	if (ret) {
+		dev_err(dev, "failed to register clock notifier: %d\n", ret);
+		return ret;
+	}
+
+	ret = devm_clk_register_regmap(dev, &a53cc->clkr);
+	if (ret) {
+		dev_err(dev, "failed to register regmap clock: %d\n", ret);
+		goto err;
+	}
+
+	ret = of_clk_add_hw_provider(parent->of_node, of_clk_hw_simple_get,
+				     &a53cc->clkr.hw);
+	if (ret) {
+		dev_err(dev, "failed to add clock provider: %d\n", ret);
+		goto err;
+	}
+
+	platform_set_drvdata(pdev, a53cc);
+
+	return 0;
+
+err:
+	clk_notifier_unregister(a53cc->pclk, &a53cc->clk_nb);
+	return ret;
+}
+
+static int qcom_apcs_msm8916_clk_remove(struct platform_device *pdev)
+{
+	struct clk_regmap_mux_div *a53cc = platform_get_drvdata(pdev);
+	struct device *parent = pdev->dev.parent;
+
+	clk_notifier_unregister(a53cc->pclk, &a53cc->clk_nb);
+	of_clk_del_provider(parent->of_node);
+
+	return 0;
+}
+
+static struct platform_driver qcom_apcs_msm8916_clk_driver = {
+	.probe = qcom_apcs_msm8916_clk_probe,
+	.remove = qcom_apcs_msm8916_clk_remove,
+	.driver = {
+		.name = "qcom-apcs-msm8916-clk",
+	},
+};
+module_platform_driver(qcom_apcs_msm8916_clk_driver);
+
+MODULE_AUTHOR("Georgi Djakov <georgi.djakov@linaro.org>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Qualcomm MSM8916 APCS clock driver");

drivers/clk/qcom/clk-regmap-mux-div.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, Linaro Limited
+ * Author: Georgi Djakov <georgi.djakov@linaro.org>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/regmap.h>
+
+#include "clk-regmap-mux-div.h"
+
+#define CMD_RCGR			0x0
+#define CMD_RCGR_UPDATE			BIT(0)
+#define CMD_RCGR_DIRTY_CFG		BIT(4)
+#define CMD_RCGR_ROOT_OFF		BIT(31)
+#define CFG_RCGR			0x4
+
+#define to_clk_regmap_mux_div(_hw) \
+	container_of(to_clk_regmap(_hw), struct clk_regmap_mux_div, clkr)
+
+int mux_div_set_src_div(struct clk_regmap_mux_div *md, u32 src, u32 div)
+{
+	int ret, count;
+	u32 val, mask;
+	const char *name = clk_hw_get_name(&md->clkr.hw);
+
+	val = (div << md->hid_shift) | (src << md->src_shift);
+	mask = ((BIT(md->hid_width) - 1) << md->hid_shift) |
+	       ((BIT(md->src_width) - 1) << md->src_shift);
+
+	ret = regmap_update_bits(md->clkr.regmap, CFG_RCGR + md->reg_offset,
+				 mask, val);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(md->clkr.regmap, CMD_RCGR + md->reg_offset,
+				 CMD_RCGR_UPDATE, CMD_RCGR_UPDATE);
+	if (ret)
+		return ret;
+
+	/* Wait for update to take effect */
+	for (count = 500; count > 0; count--) {
+		ret = regmap_read(md->clkr.regmap, CMD_RCGR + md->reg_offset,
+				  &val);
+		if (ret)
+			return ret;
+		if (!(val & CMD_RCGR_UPDATE))
+			return 0;
+		udelay(1);
+	}
+
+	pr_err("%s: RCG did not update its configuration", name);
+	return -EBUSY;
+}
+EXPORT_SYMBOL_GPL(mux_div_set_src_div);
+
+static void mux_div_get_src_div(struct clk_regmap_mux_div *md, u32 *src,
+				u32 *div)
+{
+	u32 val, d, s;
+	const char *name = clk_hw_get_name(&md->clkr.hw);
+
+	regmap_read(md->clkr.regmap, CMD_RCGR + md->reg_offset, &val);
+
+	if (val & CMD_RCGR_DIRTY_CFG) {
+		pr_err("%s: RCG configuration is pending\n", name);
+		return;
+	}
+
+	regmap_read(md->clkr.regmap, CFG_RCGR + md->reg_offset, &val);
+	s = (val >> md->src_shift);
+	s &= BIT(md->src_width) - 1;
+	*src = s;
+
+	d = (val >> md->hid_shift);
+	d &= BIT(md->hid_width) - 1;
+	*div = d;
+}
+
+static inline bool is_better_rate(unsigned long req, unsigned long best,
+				  unsigned long new)
+{
+	return (req <= new && new < best) || (best < req && best < new);
+}
+
+static int mux_div_determine_rate(struct clk_hw *hw,
+				  struct clk_rate_request *req)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+	unsigned int i, div, max_div;
+	unsigned long actual_rate, best_rate = 0;
+	unsigned long req_rate = req->rate;
+
+	for (i = 0; i < clk_hw_get_num_parents(hw); i++) {
+		struct clk_hw *parent = clk_hw_get_parent_by_index(hw, i);
+		unsigned long parent_rate = clk_hw_get_rate(parent);
+
+		max_div = BIT(md->hid_width) - 1;
+		for (div = 1; div < max_div; div++) {
+			parent_rate = mult_frac(req_rate, div, 2);
+			parent_rate = clk_hw_round_rate(parent, parent_rate);
+			actual_rate = mult_frac(parent_rate, 2, div);
+
+			if (is_better_rate(req_rate, best_rate, actual_rate)) {
+				best_rate = actual_rate;
+				req->rate = best_rate;
+				req->best_parent_rate = parent_rate;
+				req->best_parent_hw = parent;
+			}
+
+			if (actual_rate < req_rate || best_rate <= req_rate)
+				break;
+		}
+	}
+
+	if (!best_rate)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int __mux_div_set_rate_and_parent(struct clk_hw *hw, unsigned long rate,
+					 unsigned long prate, u32 src)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+	int ret;
+	u32 div, max_div, best_src = 0, best_div = 0;
+	unsigned int i;
+	unsigned long actual_rate, best_rate = 0;
+
+	for (i = 0; i < clk_hw_get_num_parents(hw); i++) {
+		struct clk_hw *parent = clk_hw_get_parent_by_index(hw, i);
+		unsigned long parent_rate = clk_hw_get_rate(parent);
+
+		max_div = BIT(md->hid_width) - 1;
+		for (div = 1; div < max_div; div++) {
+			parent_rate = mult_frac(rate, div, 2);
+			parent_rate = clk_hw_round_rate(parent, parent_rate);
+			actual_rate = mult_frac(parent_rate, 2, div);
+
+			if (is_better_rate(rate, best_rate, actual_rate)) {
+				best_rate = actual_rate;
+				best_src = md->parent_map[i];
+				best_div = div - 1;
+			}
+
+			if (actual_rate < rate || best_rate <= rate)
+				break;
+		}
+	}
+
+	ret = mux_div_set_src_div(md, best_src, best_div);
+	if (!ret) {
+		md->div = best_div;
+		md->src = best_src;
+	}
+
+	return ret;
+}
+
+static u8 mux_div_get_parent(struct clk_hw *hw)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+	const char *name = clk_hw_get_name(hw);
+	u32 i, div, src = 0;
+
+	mux_div_get_src_div(md, &src, &div);
+
+	for (i = 0; i < clk_hw_get_num_parents(hw); i++)
+		if (src == md->parent_map[i])
+			return i;
+
+	pr_err("%s: Can't find parent with src %d\n", name, src);
+	return 0;
+}
+
+static int mux_div_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+
+	return mux_div_set_src_div(md, md->parent_map[index], md->div);
+}
+
+static int mux_div_set_rate(struct clk_hw *hw,
+			    unsigned long rate, unsigned long prate)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+
+	return __mux_div_set_rate_and_parent(hw, rate, prate, md->src);
+}
+
+static int mux_div_set_rate_and_parent(struct clk_hw *hw,  unsigned long rate,
+				       unsigned long prate, u8 index)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+
+	return __mux_div_set_rate_and_parent(hw, rate, prate,
+					     md->parent_map[index]);
+}
+
+static unsigned long mux_div_recalc_rate(struct clk_hw *hw, unsigned long prate)
+{
+	struct clk_regmap_mux_div *md = to_clk_regmap_mux_div(hw);
+	u32 div, src;
+	int i, num_parents = clk_hw_get_num_parents(hw);
+	const char *name = clk_hw_get_name(hw);
+
+	mux_div_get_src_div(md, &src, &div);
+	for (i = 0; i < num_parents; i++)
+		if (src == md->parent_map[i]) {
+			struct clk_hw *p = clk_hw_get_parent_by_index(hw, i);
+			unsigned long parent_rate = clk_hw_get_rate(p);
+
+			return mult_frac(parent_rate, 2, div + 1);
+		}
+
+	pr_err("%s: Can't find parent %d\n", name, src);
+	return 0;
+}
+
+const struct clk_ops clk_regmap_mux_div_ops = {
+	.get_parent = mux_div_get_parent,
+	.set_parent = mux_div_set_parent,
+	.set_rate = mux_div_set_rate,
+	.set_rate_and_parent = mux_div_set_rate_and_parent,
+	.determine_rate = mux_div_determine_rate,
+	.recalc_rate = mux_div_recalc_rate,
+};
+EXPORT_SYMBOL_GPL(clk_regmap_mux_div_ops);

drivers/clk/qcom/clk-regmap-mux-div.h

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, Linaro Limited
+ * Author: Georgi Djakov <georgi.djakov@linaro.org>
+ */
+
+#ifndef __QCOM_CLK_REGMAP_MUX_DIV_H__
+#define __QCOM_CLK_REGMAP_MUX_DIV_H__
+
+#include <linux/clk-provider.h>
+#include "clk-regmap.h"
+
+/**
+ * struct mux_div_clk - combined mux/divider clock
+ * @reg_offset: offset of the mux/divider register
+ * @hid_width:	number of bits in half integer divider
+ * @hid_shift:	lowest bit of hid value field
+ * @src_width:	number of bits in source select
+ * @src_shift:	lowest bit of source select field
+ * @div:	the divider raw configuration value
+ * @src:	the mux index which will be used if the clock is enabled
+ * @parent_map: map from parent_names index to src_sel field
+ * @clkr:	handle between common and hardware-specific interfaces
+ * @pclk:	the input PLL clock
+ * @clk_nb:	clock notifier for rate changes of the input PLL
+ */
+struct clk_regmap_mux_div {
+	u32				reg_offset;
+	u32				hid_width;
+	u32				hid_shift;
+	u32				src_width;
+	u32				src_shift;
+	u32				div;
+	u32				src;
+	const u32			*parent_map;
+	struct clk_regmap		clkr;
+	struct clk			*pclk;
+	struct notifier_block		clk_nb;
+};
+
+extern const struct clk_ops clk_regmap_mux_div_ops;
+extern int mux_div_set_src_div(struct clk_regmap_mux_div *md, u32 src, u32 div);
+
+#endif