wcn36xx: Fix dynamic power saving

Since driver does not report hardware dynamic power saving cap,
this is up to the mac80211 to manage power saving timeout and
state machine, using the ieee80211 config callback to report
PS changes. This patch enables/disables PS mode according to
the new configuration.

Remove old behaviour enabling PS mode in a static way, this make
the device unusable when power save is enabled since device is
forced to PS regardless RX/TX traffic.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/ath/wcn36xx/main.c

@@ -384,6 +384,18 @@ static int wcn36xx_config(struct ieee80211_hw *hw, u32 changed)
 		}
 	}
 
+	if (changed & IEEE80211_CONF_CHANGE_PS) {
+		list_for_each_entry(tmp, &wcn->vif_list, list) {
+			vif = wcn36xx_priv_to_vif(tmp);
+			if (hw->conf.flags & IEEE80211_CONF_PS) {
+				if (vif->bss_conf.ps) /* ps allowed ? */
+					wcn36xx_pmc_enter_bmps_state(wcn, vif);
+			} else {
+				wcn36xx_pmc_exit_bmps_state(wcn, vif);
+			}
+		}
+	}
+
 	mutex_unlock(&wcn->conf_mutex);
 
 	return 0;
@@ -747,17 +759,6 @@ static void wcn36xx_bss_info_changed(struct ieee80211_hw *hw,
 		vif_priv->dtim_period = bss_conf->dtim_period;
 	}
 
-	if (changed & BSS_CHANGED_PS) {
-		wcn36xx_dbg(WCN36XX_DBG_MAC,
-			    "mac bss PS set %d\n",
-			    bss_conf->ps);
-		if (bss_conf->ps) {
-			wcn36xx_pmc_enter_bmps_state(wcn, vif);
-		} else {
-			wcn36xx_pmc_exit_bmps_state(wcn, vif);
-		}
-	}
-
 	if (changed & BSS_CHANGED_BSSID) {
 		wcn36xx_dbg(WCN36XX_DBG_MAC, "mac bss changed_bssid %pM\n",
 			    bss_conf->bssid);

drivers/net/wireless/ath/wcn36xx/pmc.c

@@ -45,8 +45,10 @@ int wcn36xx_pmc_exit_bmps_state(struct wcn36xx *wcn,
 	struct wcn36xx_vif *vif_priv = wcn36xx_vif_to_priv(vif);
 
 	if (WCN36XX_BMPS != vif_priv->pw_state) {
-		wcn36xx_err("Not in BMPS mode, no need to exit from BMPS mode!\n");
-		return -EINVAL;
+		/* Unbalanced call or last BMPS enter failed */
+		wcn36xx_dbg(WCN36XX_DBG_PMC,
+			    "Not in BMPS mode, no need to exit\n");
+		return -EALREADY;
 	}
 	wcn36xx_smd_exit_bmps(wcn, vif);
 	vif_priv->pw_state = WCN36XX_FULL_POWER;