Merge tag 'ds2760-for-v4.19-signed' into psy-next

Immutable branch for moving ds2760 driver from w1 to power supply
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>

Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt

+Devicetree bindings for Maxim DS2760
+====================================
+
+The ds2760 is a w1 slave device and must hence have its sub-node in DT
+under a w1 bus master node.
+
+The device exposes a power supply, so the details described in
+Documentation/devicetree/bindings/power/supply/power_supply.txt apply.
+
+Required properties:
+- compatible: must be "maxim,ds2760"
+
+Optional properties:
+- power-supplies:	Refers to one or more power supplies connected to
+			this battery.
+- maxim,pmod-enabled:	This boolean property enables the DS2760 to enter
+			sleep mode when the DQ line goes low for greater
+			than 2 seconds and leave sleep Mode when the DQ
+			line goes high.
+- maxim,cache-time-ms:	Time im milliseconds to cache the data for. When
+			this time expires, the values are read again from
+			the hardware. Defaults to 1000.
+- rated-capacity-microamp-hours:
+			The rated capacity of the battery, in mAh.
+			If not specified, the value stored in the
+			non-volatile chip memory is used.

Documentation/devicetree/bindings/w1/w1-gpio.txt

@@ -13,10 +13,15 @@ Optional properties:
  - linux,open-drain: if specified, the data pin is considered in
 		     open-drain mode.
 
+Also refer to the generic w1.txt document.
+
 Examples:
 
-	onewire@0 {
+	onewire {
 		compatible = "w1-gpio";
-		gpios = <&gpio 126 0>, <&gpio 105 0>;
-	};
+		gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
 
+		battery {
+			// ...
+		};
+	};

Documentation/devicetree/bindings/w1/w1.txt

+Generic devicetree bindings for onewire (w1) busses
+===================================================
+
+Onewire busses are described through nodes of their master bus controller.
+Slave devices are listed as sub-nodes of such master devices. For now, only
+one slave is allowed per bus master.
+
+
+Example:
+
+	charger: charger {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio 100 0>, <&gpio 101 0>;
+
+		battery {
+			compatible = "maxim,ds2760";
+			power-supplies = <&charger>;
+		};
+	};

drivers/power/supply/Kconfig

@@ -103,7 +103,7 @@ config BATTERY_CPCAP
 
 config BATTERY_DS2760
 	tristate "DS2760 battery driver (HP iPAQ & others)"
-	depends on W1 && W1_SLAVE_DS2760
+	depends on W1
 	help
 	  Say Y here to enable support for batteries with ds2760 chip.
 

drivers/w1/slaves/Kconfig

@@ -100,18 +100,6 @@ config W1_SLAVE_DS2438
 	  Say Y here if you want to use a 1-wire
 	  DS2438 Smart Battery Monitor device support
 
-config W1_SLAVE_DS2760
-	tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
-	help
-	  If you enable this you will have the DS2760 battery monitor
-	  chip support.
-
-	  The battery monitor chip is used in many batteries/devices
-	  as the one who is responsible for charging/discharging/monitoring
-	  Li+ batteries.
-
-	  If you are unsure, say N.
-
 config W1_SLAVE_DS2780
 	tristate "Dallas 2780 battery monitor chip"
 	help

drivers/w1/slaves/Makefile

@@ -14,7 +14,6 @@ obj-$(CONFIG_W1_SLAVE_DS2431)	+= w1_ds2431.o
 obj-$(CONFIG_W1_SLAVE_DS2805)	+= w1_ds2805.o
 obj-$(CONFIG_W1_SLAVE_DS2433)	+= w1_ds2433.o
 obj-$(CONFIG_W1_SLAVE_DS2438)	+= w1_ds2438.o
-obj-$(CONFIG_W1_SLAVE_DS2760)	+= w1_ds2760.o
 obj-$(CONFIG_W1_SLAVE_DS2780)	+= w1_ds2780.o
 obj-$(CONFIG_W1_SLAVE_DS2781)	+= w1_ds2781.o
 obj-$(CONFIG_W1_SLAVE_DS28E04)	+= w1_ds28e04.o

drivers/w1/slaves/w1_ds2760.c

-/*
- * 1-Wire implementation for the ds2760 chip
- *
- * Copyright © 2004-2005, Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
- *
- * Use consistent with the GNU GPL is permitted,
- * provided that this copyright notice is
- * preserved in its entirety in all copies and derived works.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/device.h>
-#include <linux/types.h>
-#include <linux/platform_device.h>
-#include <linux/mutex.h>
-#include <linux/idr.h>
-#include <linux/gfp.h>
-
-#include <linux/w1.h>
-
-#include "w1_ds2760.h"
-
-#define W1_FAMILY_DS2760	0x30
-
-static int w1_ds2760_io(struct device *dev, char *buf, int addr, size_t count,
-			int io)
-{
-	struct w1_slave *sl = container_of(dev, struct w1_slave, dev);
-
-	if (!dev)
-		return 0;
-
-	mutex_lock(&sl->master->bus_mutex);
-
-	if (addr > DS2760_DATA_SIZE || addr < 0) {
-		count = 0;
-		goto out;
-	}
-	if (addr + count > DS2760_DATA_SIZE)
-		count = DS2760_DATA_SIZE - addr;
-
-	if (!w1_reset_select_slave(sl)) {
-		if (!io) {
-			w1_write_8(sl->master, W1_DS2760_READ_DATA);
-			w1_write_8(sl->master, addr);
-			count = w1_read_block(sl->master, buf, count);
-		} else {
-			w1_write_8(sl->master, W1_DS2760_WRITE_DATA);
-			w1_write_8(sl->master, addr);
-			w1_write_block(sl->master, buf, count);
-			/* XXX w1_write_block returns void, not n_written */
-		}
-	}
-
-out:
-	mutex_unlock(&sl->master->bus_mutex);
-
-	return count;
-}
-
-int w1_ds2760_read(struct device *dev, char *buf, int addr, size_t count)
-{
-	return w1_ds2760_io(dev, buf, addr, count, 0);
-}
-EXPORT_SYMBOL(w1_ds2760_read);
-
-int w1_ds2760_write(struct device *dev, char *buf, int addr, size_t count)
-{
-	return w1_ds2760_io(dev, buf, addr, count, 1);
-}
-EXPORT_SYMBOL(w1_ds2760_write);
-
-static int w1_ds2760_eeprom_cmd(struct device *dev, int addr, int cmd)
-{
-	struct w1_slave *sl = container_of(dev, struct w1_slave, dev);
-
-	if (!dev)
-		return -EINVAL;
-
-	mutex_lock(&sl->master->bus_mutex);
-
-	if (w1_reset_select_slave(sl) == 0) {
-		w1_write_8(sl->master, cmd);
-		w1_write_8(sl->master, addr);
-	}
-
-	mutex_unlock(&sl->master->bus_mutex);
-	return 0;
-}
-
-int w1_ds2760_store_eeprom(struct device *dev, int addr)
-{
-	return w1_ds2760_eeprom_cmd(dev, addr, W1_DS2760_COPY_DATA);
-}
-EXPORT_SYMBOL(w1_ds2760_store_eeprom);
-
-int w1_ds2760_recall_eeprom(struct device *dev, int addr)
-{
-	return w1_ds2760_eeprom_cmd(dev, addr, W1_DS2760_RECALL_DATA);
-}
-EXPORT_SYMBOL(w1_ds2760_recall_eeprom);
-
-static ssize_t w1_slave_read(struct file *filp, struct kobject *kobj,
-			     struct bin_attribute *bin_attr, char *buf,
-			     loff_t off, size_t count)
-{
-	struct device *dev = container_of(kobj, struct device, kobj);
-	return w1_ds2760_read(dev, buf, off, count);
-}
-
-static BIN_ATTR_RO(w1_slave, DS2760_DATA_SIZE);
-
-static struct bin_attribute *w1_ds2760_bin_attrs[] = {
-	&bin_attr_w1_slave,
-	NULL,
-};
-
-static const struct attribute_group w1_ds2760_group = {
-	.bin_attrs = w1_ds2760_bin_attrs,
-};
-
-static const struct attribute_group *w1_ds2760_groups[] = {
-	&w1_ds2760_group,
-	NULL,
-};
-
-static int w1_ds2760_add_slave(struct w1_slave *sl)
-{
-	int ret;
-	struct platform_device *pdev;
-
-	pdev = platform_device_alloc("ds2760-battery", PLATFORM_DEVID_AUTO);
-	if (!pdev)
-		return -ENOMEM;
-	pdev->dev.parent = &sl->dev;
-
-	ret = platform_device_add(pdev);
-	if (ret)
-		goto pdev_add_failed;
-
-	dev_set_drvdata(&sl->dev, pdev);
-
-	return 0;
-
-pdev_add_failed:
-	platform_device_put(pdev);
-
-	return ret;
-}
-
-static void w1_ds2760_remove_slave(struct w1_slave *sl)
-{
-	struct platform_device *pdev = dev_get_drvdata(&sl->dev);
-
-	platform_device_unregister(pdev);
-}
-
-static struct w1_family_ops w1_ds2760_fops = {
-	.add_slave    = w1_ds2760_add_slave,
-	.remove_slave = w1_ds2760_remove_slave,
-	.groups       = w1_ds2760_groups,
-};
-
-static struct w1_family w1_ds2760_family = {
-	.fid = W1_FAMILY_DS2760,
-	.fops = &w1_ds2760_fops,
-};
-module_w1_family(w1_ds2760_family);
-
-MODULE_AUTHOR("Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>");
-MODULE_DESCRIPTION("1-wire Driver Dallas 2760 battery monitor chip");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("w1-family-" __stringify(W1_FAMILY_DS2760));

drivers/w1/slaves/w1_ds2760.h

-/*
- * 1-Wire implementation for the ds2760 chip
- *
- * Copyright © 2004-2005, Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
- *
- * Use consistent with the GNU GPL is permitted,
- * provided that this copyright notice is
- * preserved in its entirety in all copies and derived works.
- *
- */
-
-#ifndef __w1_ds2760_h__
-#define __w1_ds2760_h__
-
-/* Known commands to the DS2760 chip */
-#define W1_DS2760_SWAP			0xAA
-#define W1_DS2760_READ_DATA		0x69
-#define W1_DS2760_WRITE_DATA		0x6C
-#define W1_DS2760_COPY_DATA		0x48
-#define W1_DS2760_RECALL_DATA		0xB8
-#define W1_DS2760_LOCK			0x6A
-
-/* Number of valid register addresses */
-#define DS2760_DATA_SIZE		0x40
-
-#define DS2760_PROTECTION_REG		0x00
-
-#define DS2760_STATUS_REG		0x01
-#define DS2760_STATUS_IE		(1 << 2)
-#define DS2760_STATUS_SWEN		(1 << 3)
-#define DS2760_STATUS_RNAOP		(1 << 4)
-#define DS2760_STATUS_PMOD		(1 << 5)
-
-#define DS2760_EEPROM_REG		0x07
-#define DS2760_SPECIAL_FEATURE_REG	0x08
-#define DS2760_VOLTAGE_MSB		0x0c
-#define DS2760_VOLTAGE_LSB		0x0d
-#define DS2760_CURRENT_MSB		0x0e
-#define DS2760_CURRENT_LSB		0x0f
-#define DS2760_CURRENT_ACCUM_MSB	0x10
-#define DS2760_CURRENT_ACCUM_LSB	0x11
-#define DS2760_TEMP_MSB			0x18
-#define DS2760_TEMP_LSB			0x19
-#define DS2760_EEPROM_BLOCK0		0x20
-#define DS2760_ACTIVE_FULL		0x20
-#define DS2760_EEPROM_BLOCK1		0x30
-#define DS2760_STATUS_WRITE_REG		0x31
-#define DS2760_RATED_CAPACITY		0x32
-#define DS2760_CURRENT_OFFSET_BIAS	0x33
-#define DS2760_ACTIVE_EMPTY		0x3b
-
-extern int w1_ds2760_read(struct device *dev, char *buf, int addr,
-			  size_t count);
-extern int w1_ds2760_write(struct device *dev, char *buf, int addr,
-			   size_t count);
-extern int w1_ds2760_store_eeprom(struct device *dev, int addr);
-extern int w1_ds2760_recall_eeprom(struct device *dev, int addr);
-
-#endif /* !__w1_ds2760_h__ */

drivers/w1/w1.c

@@ -26,6 +26,7 @@
 #include <linux/kthread.h>
 #include <linux/freezer.h>
 #include <linux/hwmon.h>
+#include <linux/of.h>
 
 #include <linux/atomic.h>
 
@@ -686,6 +687,8 @@ static int __w1_attach_slave_device(struct w1_slave *sl)
 	sl->dev.bus = &w1_bus_type;
 	sl->dev.release = &w1_slave_release;
 	sl->dev.groups = w1_slave_groups;
+	sl->dev.of_node = of_find_matching_node(sl->master->dev.of_node,
+						sl->family->of_match_table);
 
 	dev_set_name(&sl->dev, "%02x-%012llx",
 		 (unsigned int) sl->reg_num.family,

include/linux/w1.h

@@ -274,6 +274,8 @@ struct w1_family {
 
 	struct w1_family_ops	*fops;
 
+	const struct of_device_id *of_match_table;
+
 	atomic_t		refcnt;
 };