Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds

Pull LED subsystem updates from Bryan Wu:
 "In this cycle, we finished to merge patches for LED Flash class
  driver.

  Other than that we have some bug fixes and new drivers for LED
  controllers"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
  leds:lp55xx: fix firmware loading error
  leds: fix max77693-led build errors
  leds: fix aat1290 build errors
  leds: aat1290: pass flags parameter to devm_gpiod_get
  leds: ktd2692: pass flags parameter to devm_gpiod_get
  drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
  leds: aat1290: add support for V4L2 Flash sub-device
  DT: aat1290: Document handling external strobe sources
  leds: max77693: add support for V4L2 Flash sub-device
  media: Add registration helpers for V4L2 flash sub-devices
  v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
  Documentation: leds: Add description of v4l2-flash sub-device
  leds: add BCM6358 LED driver
  leds: add DT binding for BCM6358 LED controller
  leds: fix brightness changing when software blinking is active
  Documentation: leds-lp5523: describe master fader attributes
  leds: lp5523: add master_fader support
  leds: leds-gpio: Allow compile test if !GPIOLIB
  leds: leds-gpio: Add missing #include <linux/of.h>
  gpiolib: Add missing dummies for the unified device properties interface
  ...

Documentation/devicetree/bindings/leds/leds-aat1290.txt

+* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
+
+The device is controlled through two pins: FL_EN and EN_SET. The pins when,
+asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. CPU or camera sensor) there is an additional switch required, independent
+of the flash chip. The switch is controlled with pin control.
+
+Required properties:
+
+- compatible : Must be "skyworks,aat1290".
+- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
+- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
+
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configuration
+		node, which sets the host as a strobe signal provider. Entry
+		"isp" must refer to the pin configuration node, which sets the
+		ISP as a strobe signal provider.
+
+A discrete LED element connected to the device must be represented by a child
+node - see Documentation/devicetree/bindings/leds/common.txt.
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+                       Maximum flash LED supply current can be calculated using
+                       following formula: I = 1A * 162kohm / Rset.
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+                     Maximum flash timeout can be calculated using following
+                     formula: T = 8.82 * 10^9 * Ct.
+
+Optional properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
+a switch that allows for routing strobe signal either from the host or from
+the camera sensor):
+
+#include "exynos4412.dtsi"
+
+aat1290 {
+	compatible = "skyworks,aat1290";
+	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
+	camera_flash: flash-led {
+		label = "aat1290-flash";
+		led-max-microamp = <520833>;
+		flash-max-microamp = <1012500>;
+		flash-timeout-us = <1940000>;
+	};
+};
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};

Documentation/devicetree/bindings/leds/leds-bcm6328.txt

+LEDs connected to Broadcom BCM6328 controller
+
+This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
+In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
+However, on some devices there are Serial LEDs (LEDs connected to a 74x164
+controller), which can either be controlled by software (exporting the 74x164
+as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
+by hardware using this driver.
+Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
+exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
+controlled, so the only chance to keep them working is by using this driver.
+
+BCM6328 LED controller has a HWDIS register, which controls whether a LED
+should be controlled by a hardware signal instead of the MODE register value,
+with 0 meaning hardware control enabled and 1 hardware control disabled. This
+is usually 1:1 for hardware to LED signals, but through the activity/link
+registers you have some limited control over rerouting the LEDs (as
+explained later in brcm,link-signal-sources). Even if a LED is hardware
+controlled you are still able to make it blink or light it up if it isn't,
+but you can't turn it off if the hardware decides to light it up. For this
+reason, hardware controlled LEDs aren't registered as LED class devices.
+
+Required properties:
+  - compatible : should be "brcm,bcm6328-leds".
+  - #address-cells : must be 1.
+  - #size-cells : must be 0.
+  - reg : BCM6328 LED controller address and size.
+
+Optional properties:
+  - brcm,serial-leds : Boolean, enables Serial LEDs.
+    Default : false
+
+Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
+
+LED sub-node required properties:
+  - reg : LED pin number (only LEDs 0 to 23 are valid).
+
+LED sub-node optional properties:
+  a) Optional properties for sub-nodes related to software controlled LEDs:
+    - label : see Documentation/devicetree/bindings/leds/common.txt
+    - active-low : Boolean, makes LED active low.
+      Default : false
+    - default-state : see
+      Documentation/devicetree/bindings/leds/leds-gpio.txt
+    - linux,default-trigger : see
+      Documentation/devicetree/bindings/leds/common.txt
+
+  b) Optional properties for sub-nodes related to hardware controlled LEDs:
+    - brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
+      Default : false
+    - brcm,link-signal-sources : An array of hardware link
+      signal sources. Up to four link hardware signals can get muxed into
+      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
+      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
+      4 to 7. A signal can be muxed to more than one LED, and one LED can
+      have more than one source signal.
+    - brcm,activity-signal-sources : An array of hardware activity
+      signal sources. Up to four activity hardware signals can get muxed into
+      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
+      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
+      4 to 7. A signal can be muxed to more than one LED, and one LED can
+      have more than one source signal.
+
+Examples:
+Scenario 1 : BCM6328 with 4 EPHY LEDs
+	leds0: led-controller@10000800 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10000800 0x24>;
+
+		alarm_red@2 {
+			reg = <2>;
+			active-low;
+			label = "red:alarm";
+		};
+		inet_green@3 {
+			reg = <3>;
+			active-low;
+			label = "green:inet";
+		};
+		power_green@4 {
+			reg = <4>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+		ephy0_spd@17 {
+			reg = <17>;
+			brcm,hardware-controlled;
+		};
+		ephy1_spd@18 {
+			reg = <18>;
+			brcm,hardware-controlled;
+		};
+		ephy2_spd@19 {
+			reg = <19>;
+			brcm,hardware-controlled;
+		};
+		ephy3_spd@20 {
+			reg = <20>;
+			brcm,hardware-controlled;
+		};
+	};
+
+Scenario 2 : BCM63268 with Serial/GPHY0 LEDs
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+		brcm,serial-leds;
+
+		gphy0_spd0@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+		};
+		gphy0_spd1@1 {
+			reg = <1>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <1>;
+		};
+		inet_red@2 {
+			reg = <2>;
+			active-low;
+			label = "red:inet";
+		};
+		dsl_green@3 {
+			reg = <3>;
+			active-low;
+			label = "green:dsl";
+		};
+		usb_green@4 {
+			reg = <4>;
+			active-low;
+			label = "green:usb";
+		};
+		wps_green@7 {
+			reg = <7>;
+			active-low;
+			label = "green:wps";
+		};
+		inet_green@8 {
+			reg = <8>;
+			active-low;
+			label = "green:inet";
+		};
+		ephy0_act@9 {
+			reg = <9>;
+			brcm,hardware-controlled;
+		};
+		ephy1_act@10 {
+			reg = <10>;
+			brcm,hardware-controlled;
+		};
+		ephy2_act@11 {
+			reg = <11>;
+			brcm,hardware-controlled;
+		};
+		gphy0_act@12 {
+			reg = <12>;
+			brcm,hardware-controlled;
+		};
+		ephy0_spd@13 {
+			reg = <13>;
+			brcm,hardware-controlled;
+		};
+		ephy1_spd@14 {
+			reg = <14>;
+			brcm,hardware-controlled;
+		};
+		ephy2_spd@15 {
+			reg = <15>;
+			brcm,hardware-controlled;
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 3 : BCM6362 with 1 LED for each EPHY
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+			brcm,activity-signal-sources = <0>;
+			/* USB link/activity routed to USB LED */
+		};
+		inet@1 {
+			reg = <1>;
+			brcm,hardware-controlled;
+			brcm,activity-signal-sources = <1>;
+			/* INET activity routed to INET LED */
+		};
+		ephy0@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4>;
+			/* EPHY0 link routed to EPHY0 LED */
+		};
+		ephy1@5 {
+			reg = <5>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <5>;
+			/* EPHY1 link routed to EPHY1 LED */
+		};
+		ephy2@6 {
+			reg = <6>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <6>;
+			/* EPHY2 link routed to EPHY2 LED */
+		};
+		ephy3@7 {
+			reg = <7>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <7>;
+			/* EPHY3 link routed to EPHY3 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 4 : BCM6362 with 1 LED for all EPHYs
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0 1>;
+			brcm,activity-signal-sources = <0 1>;
+			/* USB/INET link/activity routed to USB LED */
+		};
+		ephy@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4 5 6 7>;
+			/* EPHY0/1/2/3 link routed to EPHY0 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 5 : BCM6362 with EPHY LEDs swapped
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+			brcm,activity-signal-sources = <0 1>;
+			/* USB link/act and INET act routed to USB LED */
+		};
+		ephy0@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <7>;
+			/* EPHY3 link routed to EPHY0 LED */
+		};
+		ephy1@5 {
+			reg = <5>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <6>;
+			/* EPHY2 link routed to EPHY1 LED */
+		};
+		ephy2@6 {
+			reg = <6>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <5>;
+			/* EPHY1 link routed to EPHY2 LED */
+		};
+		ephy3@7 {
+			reg = <7>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4>;
+			/* EPHY0 link routed to EPHY3 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};

Documentation/devicetree/bindings/leds/leds-bcm6358.txt

+LEDs connected to Broadcom BCM6358 controller
+
+This controller is present on BCM6358 and BCM6368.
+In these SoCs there are Serial LEDs (LEDs connected to a 74x164 controller),
+which can either be controlled by software (exporting the 74x164 as spi-gpio.
+See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
+by hardware using this driver.
+
+Required properties:
+  - compatible : should be "brcm,bcm6358-leds".
+  - #address-cells : must be 1.
+  - #size-cells : must be 0.
+  - reg : BCM6358 LED controller address and size.
+
+Optional properties:
+  - brcm,clk-div : SCK signal divider. Possible values are 1, 2, 4 and 8.
+    Default : 1
+  - brcm,clk-dat-low : Boolean, makes clock and data signals active low.
+    Default : false
+
+Each LED is represented as a sub-node of the brcm,bcm6358-leds device.
+
+LED sub-node required properties:
+  - reg : LED pin number (only LEDs 0 to 31 are valid).
+
+LED sub-node optional properties:
+  - label : see Documentation/devicetree/bindings/leds/common.txt
+  - active-low : Boolean, makes LED active low.
+    Default : false
+  - default-state : see
+    Documentation/devicetree/bindings/leds/leds-gpio.txt
+  - linux,default-trigger : see
+    Documentation/devicetree/bindings/leds/common.txt
+
+Examples:
+Scenario 1 : BCM6358
+	leds0: led-controller@fffe00d0 {
+		compatible = "brcm,bcm6358-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfffe00d0 0x8>;
+
+		alarm_white {
+			reg = <0>;
+			active-low;
+			label = "white:alarm";
+		};
+		tv_white {
+			reg = <2>;
+			active-low;
+			label = "white:tv";
+		};
+		tel_white {
+			reg = <3>;
+			active-low;
+			label = "white:tel";
+		};
+		adsl_white {
+			reg = <4>;
+			active-low;
+			label = "white:adsl";
+		};
+	};
+
+Scenario 2 : BCM6368
+	leds0: led-controller@100000d0 {
+		compatible = "brcm,bcm6358-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x100000d0 0x8>;
+		brcm,pol-low;
+		brcm,clk-div = <4>;
+
+		power_red {
+			reg = <0>;
+			active-low;
+			label = "red:power";
+		};
+		power_green {
+			reg = <1>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+		power_blue {
+			reg = <2>;
+			label = "blue:power";
+		};
+		broadband_red {
+			reg = <3>;
+			active-low;
+			label = "red:broadband";
+		};
+		broadband_green {
+			reg = <4>;
+			label = "green:broadband";
+		};
+		broadband_blue {
+			reg = <5>;
+			active-low;
+			label = "blue:broadband";
+		};
+		wireless_red {
+			reg = <6>;
+			active-low;
+			label = "red:wireless";
+		};
+		wireless_green {
+			reg = <7>;
+			active-low;
+			label = "green:wireless";
+		};
+		wireless_blue {
+			reg = <8>;
+			label = "blue:wireless";
+		};
+		phone_red {
+			reg = <9>;
+			active-low;
+			label = "red:phone";
+		};
+		phone_green {
+			reg = <10>;
+			active-low;
+			label = "green:phone";
+		};
+		phone_blue {
+			reg = <11>;
+			label = "blue:phone";
+		};
+		upgrading_red {
+			reg = <12>;
+			active-low;
+			label = "red:upgrading";
+		};
+		upgrading_green {
+			reg = <13>;
+			active-low;
+			label = "green:upgrading";
+		};
+		upgrading_blue {
+			reg = <14>;
+			label = "blue:upgrading";
+		};
+	};

Documentation/devicetree/bindings/leds/leds-ktd2692.txt

+* Kinetic Technologies - KTD2692 Flash LED Driver
+
+KTD2692 is the ideal power solution for high-power flash LEDs.
+It uses ExpressWire single-wire programming for maximum flexibility.
+
+The ExpressWire interface through CTRL pin can control LED on/off and
+enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current,
+Flash timeout, LVP(low voltage protection).
+
+Also, When the AUX pin is pulled high while CTRL pin is high,
+LED current will be ramped up to the flash-mode current level.
+
+Required properties:
+- compatible : Should be "kinetic,ktd2692".
+- ctrl-gpios : Specifier of the GPIO connected to CTRL pin.
+- aux-gpios : Specifier of the GPIO connected to AUX pin.
+
+Optional properties:
+- vin-supply : "vin" LED supply (2.7V to 5.5V).
+  See Documentation/devicetree/bindings/regulator/regulator.txt
+
+A discrete LED element connected to the device must be represented by a child
+node - See Documentation/devicetree/bindings/leds/common.txt
+
+Required properties for flash LED child nodes:
+  See Documentation/devicetree/bindings/leds/common.txt
+- led-max-microamp : Minimum Threshold for Timer protection
+  is defined internally (Maximum 300mA).
+- flash-max-microamp : Flash LED maximum current
+  Formula : I(mA) = 15000 / Rset.
+- flash-max-timeout-us : Flash LED maximum timeout.
+
+Optional properties for flash LED child nodes:
+- label : See Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+ktd2692 {
+	compatible = "kinetic,ktd2692";
+	ctrl-gpios = <&gpc0 1 0>;
+	aux-gpios = <&gpc0 2 0>;
+	vin-supply = <&vbat>;
+
+	flash-led {
+		label = "ktd2692-flash";
+		led-max-microamp = <300000>;
+		flash-max-microamp = <1500000>;
+		flash-max-timeout-us = <1835000>;
+	};
+};

Documentation/devicetree/bindings/leds/leds-tlc591xx.txt

+LEDs connected to tlc59116 or tlc59108
+
+Required properties
+- compatible: should be "ti,tlc59116" or "ti,tlc59108"
+- #address-cells: must be 1
+- #size-cells: must be 0
+- reg: typically 0x68
+
+Each led is represented as a sub-node of the ti,tlc59116.
+See Documentation/devicetree/bindings/leds/common.txt
+
+LED sub-node properties:
+- reg: number of LED line, 0 to 15 or 0 to 7
+- label: (optional) name of LED
+- linux,default-trigger : (optional)
+
+Examples:
+
+tlc59116@68 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "ti,tlc59116";
+	reg = <0x68>;
+
+	wan@0 {
+		label = "wrt1900ac:amber:wan";
+		reg = <0x0>;
+	};
+
+	2g@2 {
+		label = "wrt1900ac:white:2g";
+		reg = <0x2>;
+	};
+
+	alive@9 {
+		label = "wrt1900ac:green:alive";
+		reg = <0x9>;
+		linux,default_trigger = "heartbeat";
+	};
+};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -114,6 +114,7 @@ isee	ISEE 2007 S.L.
 isil	Intersil
 karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
+kinetic Kinetic Technologies
 lacie	LaCie
 lantiq	Lantiq Semiconductor
 lenovo	Lenovo Group Ltd.

Documentation/leds/leds-class-flash.txt

@@ -20,3 +20,54 @@ Following sysfs attributes are exposed for controlling flash LED devices:
 	- max_flash_timeout
 	- flash_strobe
 	- flash_fault
+
+
+V4L2 flash wrapper for flash LEDs
+=================================
+
+A LED subsystem driver can be controlled also from the level of VideoForLinux2
+subsystem. In order to enable this CONFIG_V4L2_FLASH_LED_CLASS symbol has to
+be defined in the kernel config.
+
+The driver must call the v4l2_flash_init function to get registered in the
+V4L2 subsystem. The function takes six arguments:
+- dev       : flash device, e.g. an I2C device
+- of_node   : of_node of the LED, may be NULL if the same as device's
+- fled_cdev : LED flash class device to wrap
+- iled_cdev : LED flash class device representing indicator LED associated with
+	      fled_cdev, may be NULL
+- ops : V4L2 specific ops
+	* external_strobe_set - defines the source of the flash LED strobe -
+		V4L2_CID_FLASH_STROBE control or external source, typically
+		a sensor, which makes it possible to synchronise the flash
+		strobe start with exposure start,
+	* intensity_to_led_brightness and led_brightness_to_intensity - perform
+		enum led_brightness <-> V4L2 intensity conversion in a device
+		specific manner - they can be used for devices with non-linear
+		LED current scale.
+- config : configuration for V4L2 Flash sub-device
+	* dev_name - the name of the media entity, unique in the system,
+	* flash_faults - bitmask of flash faults that the LED flash class
+		device can report; corresponding LED_FAULT* bit definitions are
+		available in <linux/led-class-flash.h>,
+	* torch_intensity - constraints for the LED in TORCH mode
+		in microamperes,
+	* indicator_intensity - constraints for the indicator LED
+		in microamperes,
+	* has_external_strobe - determines whether the flash strobe source
+		can be switched to external,
+
+On remove the v4l2_flash_release function has to be called, which takes one
+argument - struct v4l2_flash pointer returned previously by v4l2_flash_init.
+This function can be safely called with NULL or error pointer argument.
+
+Please refer to drivers/leds/leds-max77693.c for an exemplary usage of the
+v4l2 flash wrapper.
+
+Once the V4L2 sub-device is registered by the driver which created the Media
+controller device, the sub-device node acts just as a node of a native V4L2
+flash API device would. The calls are simply routed to the LED flash API.
+
+Opening the V4L2 flash sub-device makes the LED subsystem sysfs interface
+unavailable. The interface is re-enabled after the V4L2 flash sub-device
+is closed.

Documentation/leds/leds-lp5523.txt

@@ -49,6 +49,36 @@ There are two ways to run LED patterns.
 2) Firmware interface - LP55xx common interface
   For the details, please refer to 'firmware' section in leds-lp55xx.txt
 
+LP5523 has three master faders. If a channel is mapped to one of
+the master faders, its output is dimmed based on the value of the master
+fader.
+
+For example,
+
+  echo "123000123" > master_fader_leds
+
+creates the following channel-fader mappings:
+
+  channel 0,6 to master_fader1
+  channel 1,7 to master_fader2
+  channel 2,8 to master_fader3
+
+Then, to have 25% of the original output on channel 0,6:
+
+  echo 64 > master_fader1
+
+To have 0% of the original output (i.e. no output) channel 1,7:
+
+  echo 0 > master_fader2
+
+To have 100% of the original output (i.e. no dimming) on channel 2,8:
+
+  echo 255 > master_fader3
+
+To clear all master fader controls:
+
+  echo "000000000" > master_fader_leds
+
 Selftest uses always the current from the platform data.
 
 Each channel contains led current settings.

drivers/leds/Kconfig

@@ -39,6 +39,32 @@ config LEDS_88PM860X
 	  This option enables support for on-chip LED drivers found on Marvell
 	  Semiconductor 88PM8606 PMIC.
 
+config LEDS_AAT1290
+	tristate "LED support for the AAT1290"
+	depends on LEDS_CLASS_FLASH
+	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
+	depends on GPIOLIB
+	depends on OF
+	depends on PINCTRL
+	help
+	 This option enables support for the LEDs on the AAT1290.
+
+config LEDS_BCM6328
+	tristate "LED Support for Broadcom BCM6328"
+	depends on LEDS_CLASS
+	depends on OF
+	help
+	  This option enables support for LEDs connected to the BCM6328
+	  LED HW controller accessed via MMIO registers.
+
+config LEDS_BCM6358
+	tristate "LED Support for Broadcom BCM6358"
+	depends on LEDS_CLASS
+	depends on OF
+	help
+	  This option enables support for LEDs connected to the BCM6358
+	  LED HW controller accessed via MMIO registers.
+
 config LEDS_LM3530
 	tristate "LCD Backlight driver for LM3530"
 	depends on LEDS_CLASS
@@ -179,7 +205,7 @@ config LEDS_PCA9532_GPIO
 config LEDS_GPIO
 	tristate "LED Support for GPIO connected LEDs"
 	depends on LEDS_CLASS
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	help
 	  This option enables support for the LEDs connected to GPIO
 	  outputs. To be useful the particular board must have LEDs
@@ -203,6 +229,7 @@ config LEDS_LP55XX_COMMON
 	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
 	select FW_LOADER
+	select FW_LOADER_USER_HELPER_FALLBACK
 	help
 	  This option supports common operations for LP5521/5523/55231/5562/8501
 	  devices.
@@ -464,6 +491,25 @@ config LEDS_TCA6507
 	  LED driver chips accessed via the I2C bus.
 	  Driver support brightness control and hardware-assisted blinking.
 
+config LEDS_TLC591XX
+	tristate "LED driver for TLC59108 and TLC59116 controllers"
+	depends on LEDS_CLASS && I2C
+	select REGMAP_I2C
+	help
+	  This option enables support for Texas Instruments TLC59108
+	  and TLC59116 LED controllers.
+
+config LEDS_MAX77693
+	tristate "LED support for MAX77693 Flash"
+	depends on LEDS_CLASS_FLASH
+	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
+	depends on MFD_MAX77693
+	depends on OF
+	help
+	  This option enables support for the flash part of the MAX77693
+	  multifunction device. It has build in control for two leds in flash
+	  and torch mode.
+
 config LEDS_MAX8997
 	tristate "LED support for MAX8997 PMIC"
 	depends on LEDS_CLASS && MFD_MAX8997
@@ -495,6 +541,15 @@ config LEDS_MENF21BMC
 	  This driver can also be built as a module. If so the module
 	  will be called leds-menf21bmc.
 
+config LEDS_KTD2692
+	tristate "LED support for KTD2692 flash LED controller"
+	depends on LEDS_CLASS_FLASH && GPIOLIB && OF
+	help
+	  This option enables support for KTD2692 LED flash connected
+	  through ExpressWire interface.
+
+	  Say Y to enable this driver.
+
 comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
 
 config LEDS_BLINKM

drivers/leds/Makefile

@@ -7,6 +7,9 @@ obj-$(CONFIG_LEDS_TRIGGERS)		+= led-triggers.o
 
 # LED Platform Drivers
 obj-$(CONFIG_LEDS_88PM860X)		+= leds-88pm860x.o
+obj-$(CONFIG_LEDS_AAT1290)		+= leds-aat1290.o
+obj-$(CONFIG_LEDS_BCM6328)		+= leds-bcm6328.o
+obj-$(CONFIG_LEDS_BCM6358)		+= leds-bcm6358.o
 obj-$(CONFIG_LEDS_BD2802)		+= leds-bd2802.o
 obj-$(CONFIG_LEDS_LOCOMO)		+= leds-locomo.o
 obj-$(CONFIG_LEDS_LM3530)		+= leds-lm3530.o
@@ -31,6 +34,7 @@ obj-$(CONFIG_LEDS_LP8501)		+= leds-lp8501.o
 obj-$(CONFIG_LEDS_LP8788)		+= leds-lp8788.o
 obj-$(CONFIG_LEDS_LP8860)		+= leds-lp8860.o
 obj-$(CONFIG_LEDS_TCA6507)		+= leds-tca6507.o
+obj-$(CONFIG_LEDS_TLC591XX)		+= leds-tlc591xx.o
 obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
 obj-$(CONFIG_LEDS_IPAQ_MICRO)		+= leds-ipaq-micro.o
 obj-$(CONFIG_LEDS_HP6XX)		+= leds-hp6xx.o
@@ -52,6 +56,7 @@ obj-$(CONFIG_LEDS_MC13783)		+= leds-mc13783.o
 obj-$(CONFIG_LEDS_NS2)			+= leds-ns2.o
 obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
 obj-$(CONFIG_LEDS_ASIC3)		+= leds-asic3.o
+obj-$(CONFIG_LEDS_MAX77693)		+= leds-max77693.o
 obj-$(CONFIG_LEDS_MAX8997)		+= leds-max8997.o
 obj-$(CONFIG_LEDS_LM355x)		+= leds-lm355x.o
 obj-$(CONFIG_LEDS_BLINKM)		+= leds-blinkm.o
@@ -59,6 +64,7 @@ obj-$(CONFIG_LEDS_SYSCON)		+= leds-syscon.o
 obj-$(CONFIG_LEDS_VERSATILE)		+= leds-versatile.o
 obj-$(CONFIG_LEDS_MENF21BMC)		+= leds-menf21bmc.o
 obj-$(CONFIG_LEDS_PM8941_WLED)		+= leds-pm8941-wled.o
+obj-$(CONFIG_LEDS_KTD2692)		+= leds-ktd2692.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_DAC124S085)		+= leds-dac124s085.o

drivers/leds/led-class.c

@@ -121,6 +121,11 @@ static void led_timer_function(unsigned long data)
 	brightness = led_get_brightness(led_cdev);
 	if (!brightness) {
 		/* Time to switch the LED on. */
+		if (led_cdev->delayed_set_value) {
+			led_cdev->blink_brightness =
+					led_cdev->delayed_set_value;
+			led_cdev->delayed_set_value = 0;
+		}
 		brightness = led_cdev->blink_brightness;
 		delay = led_cdev->blink_delay_on;
 	} else {

drivers/leds/led-core.c

@@ -119,10 +119,11 @@ void led_set_brightness(struct led_classdev *led_cdev,
 {
 	int ret = 0;
 
-	/* delay brightness setting if need to stop soft-blink timer */
+	/* delay brightness if soft-blink is active */
 	if (led_cdev->blink_delay_on || led_cdev->blink_delay_off) {
 		led_cdev->delayed_set_value = brightness;
-		schedule_work(&led_cdev->set_brightness_work);
+		if (brightness == LED_OFF)
+			schedule_work(&led_cdev->set_brightness_work);
 		return;
 	}
 

drivers/leds/leds-bcm6358.c

+/*
+ * Driver for BCM6358 memory-mapped LEDs, based on leds-syscon.c
+ *
+ * Copyright 2015 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+
+#define BCM6358_REG_MODE		0x0
+#define BCM6358_REG_CTRL		0x4
+
+#define BCM6358_SLED_CLKDIV_MASK	3
+#define BCM6358_SLED_CLKDIV_1		0
+#define BCM6358_SLED_CLKDIV_2		1
+#define BCM6358_SLED_CLKDIV_4		2
+#define BCM6358_SLED_CLKDIV_8		3
+
+#define BCM6358_SLED_POLARITY		BIT(2)
+#define BCM6358_SLED_BUSY		BIT(3)
+
+#define BCM6358_SLED_MAX_COUNT		32
+#define BCM6358_SLED_WAIT		100
+
+/**
+ * struct bcm6358_led - state container for bcm6358 based LEDs
+ * @cdev: LED class device for this LED
+ * @mem: memory resource
+ * @lock: memory lock
+ * @pin: LED pin number
+ * @active_low: LED is active low
+ */
+struct bcm6358_led {
+	struct led_classdev cdev;
+	void __iomem *mem;
+	spinlock_t *lock;
+	unsigned long pin;
+	bool active_low;
+};
+
+static void bcm6358_led_write(void __iomem *reg, unsigned long data)
+{
+	iowrite32be(data, reg);
+}
+
+static unsigned long bcm6358_led_read(void __iomem *reg)
+{
+	return ioread32be(reg);
+}
+
+static unsigned long bcm6358_led_busy(void __iomem *mem)
+{
+	unsigned long val;
+
+	while ((val = bcm6358_led_read(mem + BCM6358_REG_CTRL)) &
+		BCM6358_SLED_BUSY)
+		udelay(BCM6358_SLED_WAIT);
+
+	return val;
+}
+
+static void bcm6358_led_mode(struct bcm6358_led *led, unsigned long value)
+{
+	unsigned long val;
+
+	bcm6358_led_busy(led->mem);
+
+	val = bcm6358_led_read(led->mem + BCM6358_REG_MODE);
+	if ((led->active_low && value == LED_OFF) ||
+	    (!led->active_low && value != LED_OFF))
+		val |= BIT(led->pin);
+	else
+		val &= ~(BIT(led->pin));
+	bcm6358_led_write(led->mem + BCM6358_REG_MODE, val);
+}
+
+static void bcm6358_led_set(struct led_classdev *led_cdev,
+			    enum led_brightness value)
+{
+	struct bcm6358_led *led =
+		container_of(led_cdev, struct bcm6358_led, cdev);
+	unsigned long flags;
+
+	spin_lock_irqsave(led->lock, flags);
+	bcm6358_led_mode(led, value);
+	spin_unlock_irqrestore(led->lock, flags);
+}
+
+static int bcm6358_led(struct device *dev, struct device_node *nc, u32 reg,
+		       void __iomem *mem, spinlock_t *lock)
+{
+	struct bcm6358_led *led;
+	unsigned long flags;
+	const char *state;
+	int rc;
+
+	led = devm_kzalloc(dev, sizeof(*led), GFP_KERNEL);
+	if (!led)
+		return -ENOMEM;
+
+	led->pin = reg;
+	led->mem = mem;
+	led->lock = lock;
+
+	if (of_property_read_bool(nc, "active-low"))
+		led->active_low = true;
+
+	led->cdev.name = of_get_property(nc, "label", NULL) ? : nc->name;
+	led->cdev.default_trigger = of_get_property(nc,
+						    "linux,default-trigger",
+						    NULL);
+
+	spin_lock_irqsave(lock, flags);
+	if (!of_property_read_string(nc, "default-state", &state)) {
+		if (!strcmp(state, "on")) {
+			led->cdev.brightness = LED_FULL;
+		} else if (!strcmp(state, "keep")) {
+			unsigned long val;
+
+			bcm6358_led_busy(led->mem);
+
+			val = bcm6358_led_read(led->mem + BCM6358_REG_MODE);
+			val &= BIT(led->pin);
+			if ((led->active_low && !val) ||
+			    (!led->active_low && val))
+				led->cdev.brightness = LED_FULL;
+			else
+				led->cdev.brightness = LED_OFF;
+		} else {
+			led->cdev.brightness = LED_OFF;
+		}
+	} else {
+		led->cdev.brightness = LED_OFF;
+	}
+	bcm6358_led_mode(led, led->cdev.brightness);
+	spin_unlock_irqrestore(lock, flags);
+
+	led->cdev.brightness_set = bcm6358_led_set;
+
+	rc = led_classdev_register(dev, &led->cdev);
+	if (rc < 0)
+		return rc;
+
+	dev_dbg(dev, "registered LED %s\n", led->cdev.name);
+
+	return 0;
+}
+
+static int bcm6358_leds_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *child;
+	struct resource *mem_r;
+	void __iomem *mem;
+	spinlock_t *lock; /* memory lock */
+	unsigned long val;
+	u32 clk_div;
+
+	mem_r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!mem_r)
+		return -EINVAL;
+
+	mem = devm_ioremap_resource(dev, mem_r);
+	if (IS_ERR(mem))
+		return PTR_ERR(mem);
+
+	lock = devm_kzalloc(dev, sizeof(*lock), GFP_KERNEL);
+	if (!lock)
+		return -ENOMEM;
+
+	spin_lock_init(lock);
+
+	val = bcm6358_led_busy(mem);
+	val &= ~(BCM6358_SLED_POLARITY | BCM6358_SLED_CLKDIV_MASK);
+	if (of_property_read_bool(np, "brcm,clk-dat-low"))
+		val |= BCM6358_SLED_POLARITY;
+	of_property_read_u32(np, "brcm,clk-div", &clk_div);
+	switch (clk_div) {
+	case 8:
+		val |= BCM6358_SLED_CLKDIV_8;
+		break;
+	case 4:
+		val |= BCM6358_SLED_CLKDIV_4;
+		break;
+	case 2:
+		val |= BCM6358_SLED_CLKDIV_2;
+		break;
+	default:
+		val |= BCM6358_SLED_CLKDIV_1;
+		break;
+	}
+	bcm6358_led_write(mem + BCM6358_REG_CTRL, val);
+
+	for_each_available_child_of_node(np, child) {
+		int rc;
+		u32 reg;
+
+		if (of_property_read_u32(child, "reg", &reg))
+			continue;
+
+		if (reg >= BCM6358_SLED_MAX_COUNT) {
+			dev_err(dev, "invalid LED (%u >= %d)\n", reg,
+				BCM6358_SLED_MAX_COUNT);
+			continue;
+		}
+
+		rc = bcm6358_led(dev, child, reg, mem, lock);
+		if (rc < 0)
+			return rc;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id bcm6358_leds_of_match[] = {
+	{ .compatible = "brcm,bcm6358-leds", },
+	{ },
+};
+
+static struct platform_driver bcm6358_leds_driver = {
+	.probe = bcm6358_leds_probe,
+	.driver = {
+		.name = "leds-bcm6358",
+		.of_match_table = bcm6358_leds_of_match,
+	},
+};
+
+module_platform_driver(bcm6358_leds_driver);
+
+MODULE_AUTHOR("Álvaro Fernández Rojas <noltari@gmail.com>");
+MODULE_DESCRIPTION("LED driver for BCM6358 controllers");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:leds-bcm6358");

drivers/leds/leds-cobalt-raq.c

@@ -108,20 +108,8 @@ static int cobalt_raq_led_probe(struct platform_device *pdev)
 	return retval;
 }
 
-static int cobalt_raq_led_remove(struct platform_device *pdev)
-{
-	led_classdev_unregister(&raq_power_off_led);
-	led_classdev_unregister(&raq_web_led);
-
-	if (led_port)
-		led_port = NULL;
-
-	return 0;
-}
-
 static struct platform_driver cobalt_raq_led_driver = {
 	.probe	= cobalt_raq_led_probe,
-	.remove	= cobalt_raq_led_remove,
 	.driver = {
 		.name	= "cobalt-raq-leds",
 	},
@@ -131,5 +119,4 @@ static int __init cobalt_raq_led_init(void)
 {
 	return platform_driver_register(&cobalt_raq_led_driver);
 }
-
-module_init(cobalt_raq_led_init);
+device_initcall(cobalt_raq_led_init);

drivers/leds/leds-gpio.c

@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/leds.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/property.h>
 #include <linux/slab.h>
@@ -198,8 +199,10 @@ static struct gpio_leds_priv *gpio_leds_create(struct platform_device *pdev)
 		} else {
 			if (IS_ENABLED(CONFIG_OF) && !led.name && np)
 				led.name = np->name;
-			if (!led.name)
-				return ERR_PTR(-EINVAL);
+			if (!led.name) {
+				ret = -EINVAL;
+				goto err;
+			}
 		}
 		fwnode_property_read_string(child, "linux,default-trigger",
 					    &led.default_trigger);
@@ -217,18 +220,19 @@ static struct gpio_leds_priv *gpio_leds_create(struct platform_device *pdev)
 		if (fwnode_property_present(child, "retain-state-suspended"))
 			led.retain_state_suspended = 1;
 
-		ret = create_gpio_led(&led, &priv->leds[priv->num_leds++],
+		ret = create_gpio_led(&led, &priv->leds[priv->num_leds],
 				      dev, NULL);
 		if (ret < 0) {
 			fwnode_handle_put(child);
 			goto err;
 		}
+		priv->num_leds++;
 	}
 
 	return priv;
 
 err:
-	for (count = priv->num_leds - 2; count >= 0; count--)
+	for (count = priv->num_leds - 1; count >= 0; count--)
 		delete_gpio_led(&priv->leds[count]);
 	return ERR_PTR(ret);
 }

drivers/leds/leds-lp5523.c

@@ -50,6 +50,7 @@
 #define LP5523_REG_OP_MODE		0x01
 #define LP5523_REG_ENABLE_LEDS_MSB	0x04
 #define LP5523_REG_ENABLE_LEDS_LSB	0x05
+#define LP5523_REG_LED_CTRL_BASE	0x06
 #define LP5523_REG_LED_PWM_BASE		0x16
 #define LP5523_REG_LED_CURRENT_BASE	0x26
 #define LP5523_REG_CONFIG		0x36
@@ -57,6 +58,7 @@
 #define LP5523_REG_RESET		0x3D
 #define LP5523_REG_LED_TEST_CTRL	0x41
 #define LP5523_REG_LED_TEST_ADC		0x42
+#define LP5523_REG_MASTER_FADER_BASE	0x48
 #define LP5523_REG_CH1_PROG_START	0x4C
 #define LP5523_REG_CH2_PROG_START	0x4D
 #define LP5523_REG_CH3_PROG_START	0x4E
@@ -78,6 +80,9 @@
 #define LP5523_EXT_CLK_USED		0x08
 #define LP5523_ENG_STATUS_MASK		0x07
 
+#define LP5523_FADER_MAPPING_MASK	0xC0
+#define LP5523_FADER_MAPPING_SHIFT	6
+
 /* Memory Page Selection */
 #define LP5523_PAGE_ENG1		0
 #define LP5523_PAGE_ENG2		1
@@ -666,6 +671,137 @@ static ssize_t lp5523_selftest(struct device *dev,
 	return pos;
 }
 
+#define show_fader(nr)						\
+static ssize_t show_master_fader##nr(struct device *dev,	\
+			    struct device_attribute *attr,	\
+			    char *buf)				\
+{								\
+	return show_master_fader(dev, attr, buf, nr);		\
+}
+
+#define store_fader(nr)						\
+static ssize_t store_master_fader##nr(struct device *dev,	\
+			     struct device_attribute *attr,	\
+			     const char *buf, size_t len)	\
+{								\
+	return store_master_fader(dev, attr, buf, len, nr);	\
+}
+
+static ssize_t show_master_fader(struct device *dev,
+				 struct device_attribute *attr,
+				 char *buf, int nr)
+{
+	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
+	struct lp55xx_chip *chip = led->chip;
+	int ret;
+	u8 val;
+
+	mutex_lock(&chip->lock);
+	ret = lp55xx_read(chip, LP5523_REG_MASTER_FADER_BASE + nr - 1, &val);
+	mutex_unlock(&chip->lock);
+
+	if (ret == 0)
+		ret = sprintf(buf, "%u\n", val);
+
+	return ret;
+}
+show_fader(1)
+show_fader(2)
+show_fader(3)
+
+static ssize_t store_master_fader(struct device *dev,
+				  struct device_attribute *attr,
+				  const char *buf, size_t len, int nr)
+{
+	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
+	struct lp55xx_chip *chip = led->chip;
+	int ret;
+	unsigned long val;
+
+	if (kstrtoul(buf, 0, &val))
+		return -EINVAL;
+
+	if (val > 0xff)
+		return -EINVAL;
+
+	mutex_lock(&chip->lock);
+	ret = lp55xx_write(chip, LP5523_REG_MASTER_FADER_BASE + nr - 1,
+			   (u8)val);
+	mutex_unlock(&chip->lock);
+
+	if (ret == 0)
+		ret = len;
+
+	return ret;
+}
+store_fader(1)
+store_fader(2)
+store_fader(3)
+
+static ssize_t show_master_fader_leds(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
+	struct lp55xx_chip *chip = led->chip;
+	int i, ret, pos = 0;
+	u8 val;
+
+	mutex_lock(&chip->lock);
+
+	for (i = 0; i < LP5523_MAX_LEDS; i++) {
+		ret = lp55xx_read(chip, LP5523_REG_LED_CTRL_BASE + i, &val);
+		if (ret)
+			goto leave;
+
+		val = (val & LP5523_FADER_MAPPING_MASK)
+			>> LP5523_FADER_MAPPING_SHIFT;
+		if (val > 3) {
+			ret = -EINVAL;
+			goto leave;
+		}
+		buf[pos++] = val + '0';
+	}
+	buf[pos++] = '\n';
+	ret = pos;
+leave:
+	mutex_unlock(&chip->lock);
+	return ret;
+}
+
+static ssize_t store_master_fader_leds(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t len)
+{
+	struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
+	struct lp55xx_chip *chip = led->chip;
+	int i, n, ret;
+	u8 val;
+
+	n = min_t(int, len, LP5523_MAX_LEDS);
+
+	mutex_lock(&chip->lock);
+
+	for (i = 0; i < n; i++) {
+		if (buf[i] >= '0' && buf[i] <= '3') {
+			val = (buf[i] - '0') << LP5523_FADER_MAPPING_SHIFT;
+			ret = lp55xx_update_bits(chip,
+						 LP5523_REG_LED_CTRL_BASE + i,
+						 LP5523_FADER_MAPPING_MASK,
+						 val);
+			if (ret)
+				goto leave;
+		} else {
+			ret = -EINVAL;
+			goto leave;
+		}
+	}
+	ret = len;
+leave:
+	mutex_unlock(&chip->lock);
+	return ret;
+}
+
 static void lp5523_led_brightness_work(struct work_struct *work)
 {
 	struct lp55xx_led *led = container_of(work, struct lp55xx_led,
@@ -688,6 +824,14 @@ static LP55XX_DEV_ATTR_WO(engine1_load, store_engine1_load);
 static LP55XX_DEV_ATTR_WO(engine2_load, store_engine2_load);
 static LP55XX_DEV_ATTR_WO(engine3_load, store_engine3_load);
 static LP55XX_DEV_ATTR_RO(selftest, lp5523_selftest);
+static LP55XX_DEV_ATTR_RW(master_fader1, show_master_fader1,
+			  store_master_fader1);
+static LP55XX_DEV_ATTR_RW(master_fader2, show_master_fader2,
+			  store_master_fader2);
+static LP55XX_DEV_ATTR_RW(master_fader3, show_master_fader3,
+			  store_master_fader3);
+static LP55XX_DEV_ATTR_RW(master_fader_leds, show_master_fader_leds,
+			  store_master_fader_leds);
 
 static struct attribute *lp5523_attributes[] = {
 	&dev_attr_engine1_mode.attr,
@@ -700,6 +844,10 @@ static struct attribute *lp5523_attributes[] = {
 	&dev_attr_engine2_leds.attr,
 	&dev_attr_engine3_leds.attr,
 	&dev_attr_selftest.attr,
+	&dev_attr_master_fader1.attr,
+	&dev_attr_master_fader2.attr,
+	&dev_attr_master_fader3.attr,
+	&dev_attr_master_fader_leds.attr,
 	NULL,
 };
 

drivers/leds/leds-lp55xx-common.c

@@ -223,7 +223,7 @@ static int lp55xx_request_firmware(struct lp55xx_chip *chip)
 	const char *name = chip->cl->name;
 	struct device *dev = &chip->cl->dev;
 
-	return request_firmware_nowait(THIS_MODULE, true, name, dev,
+	return request_firmware_nowait(THIS_MODULE, false, name, dev,
 				GFP_KERNEL, chip, lp55xx_firmware_loaded);
 }
 

drivers/leds/leds-tlc591xx.c

+/*
+ * Copyright 2014 Belkin Inc.
+ * Copyright 2015 Andrew Lunn <andrew@lunn.ch>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+
+#define TLC591XX_MAX_LEDS	16
+
+#define TLC591XX_REG_MODE1	0x00
+#define MODE1_RESPON_ADDR_MASK	0xF0
+#define MODE1_NORMAL_MODE	(0 << 4)
+#define MODE1_SPEED_MODE	(1 << 4)
+
+#define TLC591XX_REG_MODE2	0x01
+#define MODE2_DIM		(0 << 5)
+#define MODE2_BLINK		(1 << 5)
+#define MODE2_OCH_STOP		(0 << 3)
+#define MODE2_OCH_ACK		(1 << 3)
+
+#define TLC591XX_REG_PWM(x)	(0x02 + (x))
+
+#define TLC591XX_REG_GRPPWM	0x12
+#define TLC591XX_REG_GRPFREQ	0x13
+
+/* LED Driver Output State, determine the source that drives LED outputs */
+#define LEDOUT_OFF		0x0	/* Output LOW */
+#define LEDOUT_ON		0x1	/* Output HI-Z */
+#define LEDOUT_DIM		0x2	/* Dimming */
+#define LEDOUT_BLINK		0x3	/* Blinking */
+#define LEDOUT_MASK		0x3
+
+#define ldev_to_led(c)		container_of(c, struct tlc591xx_led, ldev)
+#define work_to_led(work)	container_of(work, struct tlc591xx_led, work)
+
+struct tlc591xx_led {
+	bool active;
+	unsigned int led_no;
+	struct led_classdev ldev;
+	struct work_struct work;
+	struct tlc591xx_priv *priv;
+};
+
+struct tlc591xx_priv {
+	struct tlc591xx_led leds[TLC591XX_MAX_LEDS];
+	struct regmap *regmap;
+	unsigned int reg_ledout_offset;
+};
+
+struct tlc591xx {
+	unsigned int max_leds;
+	unsigned int reg_ledout_offset;
+};
+
+static const struct tlc591xx tlc59116 = {
+	.max_leds = 16,
+	.reg_ledout_offset = 0x14,
+};
+
+static const struct tlc591xx tlc59108 = {
+	.max_leds = 8,
+	.reg_ledout_offset = 0x0c,
+};
+
+static int
+tlc591xx_set_mode(struct regmap *regmap, u8 mode)
+{
+	int err;
+	u8 val;
+
+	err = regmap_write(regmap, TLC591XX_REG_MODE1, MODE1_NORMAL_MODE);
+	if (err)
+		return err;
+
+	val = MODE2_OCH_STOP | mode;
+
+	return regmap_write(regmap, TLC591XX_REG_MODE2, val);
+}
+
+static int
+tlc591xx_set_ledout(struct tlc591xx_priv *priv, struct tlc591xx_led *led,
+		    u8 val)
+{
+	unsigned int i = (led->led_no % 4) * 2;
+	unsigned int mask = LEDOUT_MASK << i;
+	unsigned int addr = priv->reg_ledout_offset + (led->led_no >> 2);
+
+	val = val << i;
+
+	return regmap_update_bits(priv->regmap, addr, mask, val);
+}
+
+static int
+tlc591xx_set_pwm(struct tlc591xx_priv *priv, struct tlc591xx_led *led,
+		 u8 brightness)
+{
+	u8 pwm = TLC591XX_REG_PWM(led->led_no);
+
+	return regmap_write(priv->regmap, pwm, brightness);
+}
+
+static void
+tlc591xx_led_work(struct work_struct *work)
+{
+	struct tlc591xx_led *led = work_to_led(work);
+	struct tlc591xx_priv *priv = led->priv;
+	enum led_brightness brightness = led->ldev.brightness;
+	int err;
+
+	switch (brightness) {
+	case 0:
+		err = tlc591xx_set_ledout(priv, led, LEDOUT_OFF);
+		break;
+	case LED_FULL:
+		err = tlc591xx_set_ledout(priv, led, LEDOUT_ON);
+		break;
+	default:
+		err = tlc591xx_set_ledout(priv, led, LEDOUT_DIM);
+		if (!err)
+			err = tlc591xx_set_pwm(priv, led, brightness);
+	}
+
+	if (err)
+		dev_err(led->ldev.dev, "Failed setting brightness\n");
+}
+
+static void
+tlc591xx_brightness_set(struct led_classdev *led_cdev,
+			enum led_brightness brightness)
+{
+	struct tlc591xx_led *led = ldev_to_led(led_cdev);
+
+	led->ldev.brightness = brightness;
+	schedule_work(&led->work);
+}
+
+static void
+tlc591xx_destroy_devices(struct tlc591xx_priv *priv, unsigned int j)
+{
+	int i = j;
+
+	while (--i >= 0) {
+		if (priv->leds[i].active) {
+			led_classdev_unregister(&priv->leds[i].ldev);
+			cancel_work_sync(&priv->leds[i].work);
+		}
+	}
+}
+
+static int
+tlc591xx_configure(struct device *dev,
+		   struct tlc591xx_priv *priv,
+		   const struct tlc591xx *tlc591xx)
+{
+	unsigned int i;
+	int err = 0;
+
+	tlc591xx_set_mode(priv->regmap, MODE2_DIM);
+	for (i = 0; i < TLC591XX_MAX_LEDS; i++) {
+		struct tlc591xx_led *led = &priv->leds[i];
+
+		if (!led->active)
+			continue;
+
+		led->priv = priv;
+		led->led_no = i;
+		led->ldev.brightness_set = tlc591xx_brightness_set;
+		led->ldev.max_brightness = LED_FULL;
+		INIT_WORK(&led->work, tlc591xx_led_work);
+		err = led_classdev_register(dev, &led->ldev);
+		if (err < 0) {
+			dev_err(dev, "couldn't register LED %s\n",
+				led->ldev.name);
+			goto exit;
+		}
+	}
+
+	return 0;
+
+exit:
+	tlc591xx_destroy_devices(priv, i);
+	return err;
+}
+
+static const struct regmap_config tlc591xx_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = 0x1e,
+};
+
+static const struct of_device_id of_tlc591xx_leds_match[] = {
+	{ .compatible = "ti,tlc59116",
+	  .data = &tlc59116 },
+	{ .compatible = "ti,tlc59108",
+	  .data = &tlc59108 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_tlc591xx_leds_match);
+
+static int
+tlc591xx_probe(struct i2c_client *client,
+	       const struct i2c_device_id *id)
+{
+	struct device_node *np = client->dev.of_node, *child;
+	struct device *dev = &client->dev;
+	const struct of_device_id *match;
+	const struct tlc591xx *tlc591xx;
+	struct tlc591xx_priv *priv;
+	int err, count, reg;
+
+	match = of_match_device(of_tlc591xx_leds_match, dev);
+	if (!match)
+		return -ENODEV;
+
+	tlc591xx = match->data;
+	if (!np)
+		return -ENODEV;
+
+	count = of_get_child_count(np);
+	if (!count || count > tlc591xx->max_leds)
+		return -EINVAL;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA))
+		return -EIO;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->regmap = devm_regmap_init_i2c(client, &tlc591xx_regmap);
+	if (IS_ERR(priv->regmap)) {
+		err = PTR_ERR(priv->regmap);
+		dev_err(dev, "Failed to allocate register map: %d\n", err);
+		return err;
+	}
+	priv->reg_ledout_offset = tlc591xx->reg_ledout_offset;
+
+	i2c_set_clientdata(client, priv);
+
+	for_each_child_of_node(np, child) {
+		err = of_property_read_u32(child, "reg", &reg);
+		if (err)
+			return err;
+		if (reg < 0 || reg >= tlc591xx->max_leds)
+			return -EINVAL;
+		if (priv->leds[reg].active)
+			return -EINVAL;
+		priv->leds[reg].active = true;
+		priv->leds[reg].ldev.name =
+			of_get_property(child, "label", NULL) ? : child->name;
+		priv->leds[reg].ldev.default_trigger =
+			of_get_property(child, "linux,default-trigger", NULL);
+	}
+	return tlc591xx_configure(dev, priv, tlc591xx);
+}
+
+static int
+tlc591xx_remove(struct i2c_client *client)
+{
+	struct tlc591xx_priv *priv = i2c_get_clientdata(client);
+
+	tlc591xx_destroy_devices(priv, TLC591XX_MAX_LEDS);
+
+	return 0;
+}
+
+static const struct i2c_device_id tlc591xx_id[] = {
+	{ "tlc59116" },
+	{ "tlc59108" },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, tlc591xx_id);
+
+static struct i2c_driver tlc591xx_driver = {
+	.driver = {
+		.name = "tlc591xx",
+		.of_match_table = of_match_ptr(of_tlc591xx_leds_match),
+	},
+	.probe = tlc591xx_probe,
+	.remove = tlc591xx_remove,
+	.id_table = tlc591xx_id,
+};
+
+module_i2c_driver(tlc591xx_driver);
+
+MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("TLC591XX LED driver");

drivers/leds/leds.h

@@ -13,7 +13,6 @@
 #ifndef __LEDS_H_INCLUDED
 #define __LEDS_H_INCLUDED
 
-#include <linux/device.h>
 #include <linux/rwsem.h>
 #include <linux/leds.h>
 
@@ -50,27 +49,4 @@ void led_stop_software_blink(struct led_classdev *led_cdev);
 extern struct rw_semaphore leds_list_lock;
 extern struct list_head leds_list;
 
-#ifdef CONFIG_LEDS_TRIGGERS
-void led_trigger_set_default(struct led_classdev *led_cdev);
-void led_trigger_set(struct led_classdev *led_cdev,
-			struct led_trigger *trigger);
-void led_trigger_remove(struct led_classdev *led_cdev);
-
-static inline void *led_get_trigger_data(struct led_classdev *led_cdev)
-{
-	return led_cdev->trigger_data;
-}
-
-#else
-#define led_trigger_set_default(x) do {} while (0)
-#define led_trigger_set(x, y) do {} while (0)
-#define led_trigger_remove(x) do {} while (0)
-#define led_get_trigger_data(x) (NULL)
-#endif
-
-ssize_t led_trigger_store(struct device *dev, struct device_attribute *attr,
-			const char *buf, size_t count);
-ssize_t led_trigger_show(struct device *dev, struct device_attribute *attr,
-			char *buf);
-
 #endif	/* __LEDS_H_INCLUDED */

drivers/media/v4l2-core/Kconfig

@@ -44,6 +44,17 @@ config V4L2_MEM2MEM_DEV
         tristate
         depends on VIDEOBUF2_CORE
 
+# Used by LED subsystem flash drivers
+config V4L2_FLASH_LED_CLASS
+	tristate "V4L2 flash API for LED flash class devices"
+	depends on VIDEO_V4L2_SUBDEV_API
+	depends on LEDS_CLASS_FLASH
+	---help---
+	  Say Y here to enable V4L2 flash API support for LED flash
+	  class drivers.
+
+	  When in doubt, say N.
+
 # Used by drivers that need Videobuf modules
 config VIDEOBUF_GEN
 	tristate

drivers/media/v4l2-core/Makefile

@@ -22,6 +22,8 @@ obj-$(CONFIG_VIDEO_TUNER) += tuner.o
 
 obj-$(CONFIG_V4L2_MEM2MEM_DEV) += v4l2-mem2mem.o
 
+obj-$(CONFIG_V4L2_FLASH_LED_CLASS) += v4l2-flash-led-class.o
+
 obj-$(CONFIG_VIDEOBUF_GEN) += videobuf-core.o
 obj-$(CONFIG_VIDEOBUF_DMA_SG) += videobuf-dma-sg.o
 obj-$(CONFIG_VIDEOBUF_DMA_CONTIG) += videobuf-dma-contig.o

drivers/media/v4l2-core/v4l2-async.c

@@ -22,10 +22,10 @@
 #include <media/v4l2-device.h>
 #include <media/v4l2-subdev.h>
 
-static bool match_i2c(struct device *dev, struct v4l2_async_subdev *asd)
+static bool match_i2c(struct v4l2_subdev *sd, struct v4l2_async_subdev *asd)
 {
 #if IS_ENABLED(CONFIG_I2C)
-	struct i2c_client *client = i2c_verify_client(dev);
+	struct i2c_client *client = i2c_verify_client(sd->dev);
 	return client &&
 		asd->match.i2c.adapter_id == client->adapter->nr &&
 		asd->match.i2c.address == client->addr;
@@ -34,14 +34,24 @@ static bool match_i2c(struct device *dev, struct v4l2_async_subdev *asd)
 #endif
 }
 
-static bool match_devname(struct device *dev, struct v4l2_async_subdev *asd)
+static bool match_devname(struct v4l2_subdev *sd,
+			  struct v4l2_async_subdev *asd)
 {
-	return !strcmp(asd->match.device_name.name, dev_name(dev));
+	return !strcmp(asd->match.device_name.name, dev_name(sd->dev));
 }
 
-static bool match_of(struct device *dev, struct v4l2_async_subdev *asd)
+static bool match_of(struct v4l2_subdev *sd, struct v4l2_async_subdev *asd)
 {
-	return dev->of_node == asd->match.of.node;
+	return sd->of_node == asd->match.of.node;
+}
+
+static bool match_custom(struct v4l2_subdev *sd, struct v4l2_async_subdev *asd)
+{
+	if (!asd->match.custom.match)
+		/* Match always */
+		return true;
+
+	return asd->match.custom.match(sd->dev, asd);
 }
 
 static LIST_HEAD(subdev_list);
@@ -51,17 +61,14 @@ static DEFINE_MUTEX(list_lock);
 static struct v4l2_async_subdev *v4l2_async_belongs(struct v4l2_async_notifier *notifier,
 						    struct v4l2_subdev *sd)
 {
+	bool (*match)(struct v4l2_subdev *, struct v4l2_async_subdev *);
 	struct v4l2_async_subdev *asd;
-	bool (*match)(struct device *, struct v4l2_async_subdev *);
 
 	list_for_each_entry(asd, &notifier->waiting, list) {
 		/* bus_type has been verified valid before */
 		switch (asd->match_type) {
 		case V4L2_ASYNC_MATCH_CUSTOM:
-			match = asd->match.custom.match;
-			if (!match)
-				/* Match always */
-				return asd;
+			match = match_custom;
 			break;
 		case V4L2_ASYNC_MATCH_DEVNAME:
 			match = match_devname;
@@ -79,7 +86,7 @@ static struct v4l2_async_subdev *v4l2_async_belongs(struct v4l2_async_notifier *
 		}
 
 		/* match cannot be NULL here */
-		if (match(sd->dev, asd))
+		if (match(sd, asd))
 			return asd;
 	}
 
@@ -266,6 +273,14 @@ int v4l2_async_register_subdev(struct v4l2_subdev *sd)
 {
 	struct v4l2_async_notifier *notifier;
 
+	/*
+	 * No reference taken. The reference is held by the device
+	 * (struct v4l2_subdev.dev), and async sub-device does not
+	 * exist independently of the device at any point of time.
+	 */
+	if (!sd->of_node && sd->dev)
+		sd->of_node = sd->dev->of_node;
+
 	mutex_lock(&list_lock);
 
 	INIT_LIST_HEAD(&sd->async_list);

include/linux/gpio/consumer.h

@@ -407,6 +407,21 @@ static inline int desc_to_gpio(const struct gpio_desc *desc)
 	return -EINVAL;
 }
 
+/* Child properties interface */
+struct fwnode_handle;
+
+static inline struct gpio_desc *fwnode_get_named_gpiod(
+	struct fwnode_handle *fwnode, const char *propname)
+{
+	return ERR_PTR(-ENOSYS);
+}
+
+static inline struct gpio_desc *devm_get_gpiod_from_child(
+	struct device *dev, const char *con_id, struct fwnode_handle *child)
+{
+	return ERR_PTR(-ENOSYS);
+}
+
 #endif /* CONFIG_GPIOLIB */
 
 /*

include/linux/leds.h

@@ -12,6 +12,7 @@
 #ifndef __LINUX_LEDS_H_INCLUDED
 #define __LINUX_LEDS_H_INCLUDED
 
+#include <linux/device.h>
 #include <linux/list.h>
 #include <linux/mutex.h>
 #include <linux/rwsem.h>
@@ -222,6 +223,11 @@ struct led_trigger {
 	struct list_head  next_trig;
 };
 
+ssize_t led_trigger_store(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count);
+ssize_t led_trigger_show(struct device *dev, struct device_attribute *attr,
+			char *buf);
+
 /* Registration functions for complex triggers */
 extern int led_trigger_register(struct led_trigger *trigger);
 extern void led_trigger_unregister(struct led_trigger *trigger);
@@ -238,6 +244,16 @@ extern void led_trigger_blink_oneshot(struct led_trigger *trigger,
 				      unsigned long *delay_on,
 				      unsigned long *delay_off,
 				      int invert);
+extern void led_trigger_set_default(struct led_classdev *led_cdev);
+extern void led_trigger_set(struct led_classdev *led_cdev,
+			struct led_trigger *trigger);
+extern void led_trigger_remove(struct led_classdev *led_cdev);
+
+static inline void *led_get_trigger_data(struct led_classdev *led_cdev)
+{
+	return led_cdev->trigger_data;
+}
+
 /**
  * led_trigger_rename_static - rename a trigger
  * @name: the new trigger name
@@ -267,6 +283,15 @@ static inline void led_trigger_register_simple(const char *name,
 static inline void led_trigger_unregister_simple(struct led_trigger *trigger) {}
 static inline void led_trigger_event(struct led_trigger *trigger,
 				enum led_brightness event) {}
+static inline void led_trigger_set_default(struct led_classdev *led_cdev) {}
+static inline void led_trigger_set(struct led_classdev *led_cdev,
+				struct led_trigger *trigger) {}
+static inline void led_trigger_remove(struct led_classdev *led_cdev) {}
+static inline void *led_get_trigger_data(struct led_classdev *led_cdev)
+{
+	return NULL;
+}
+
 #endif /* CONFIG_LEDS_TRIGGERS */
 
 /* Trigger specific functions */

include/media/v4l2-flash-led-class.h

+/*
+ * V4L2 flash LED sub-device registration helpers.
+ *
+ *	Copyright (C) 2015 Samsung Electronics Co., Ltd
+ *	Author: Jacek Anaszewski <j.anaszewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _V4L2_FLASH_H
+#define _V4L2_FLASH_H
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+struct led_classdev_flash;
+struct led_classdev;
+struct v4l2_flash;
+enum led_brightness;
+
+/*
+ * struct v4l2_flash_ctrl_data - flash control initialization data, filled
+ *				basing on the features declared by the LED flash
+ *				class driver in the v4l2_flash_config
+ * @config:	initialization data for a control
+ * @cid:	contains v4l2 flash control id if the config
+ *		field was initialized, 0 otherwise
+ */
+struct v4l2_flash_ctrl_data {
+	struct v4l2_ctrl_config config;
+	u32 cid;
+};
+
+struct v4l2_flash_ops {
+	/* setup strobing the flash by hardware pin state assertion */
+	int (*external_strobe_set)(struct v4l2_flash *v4l2_flash,
+					bool enable);
+	/* convert intensity to brightness in a device specific manner */
+	enum led_brightness (*intensity_to_led_brightness)
+		(struct v4l2_flash *v4l2_flash, s32 intensity);
+	/* convert brightness to intensity in a device specific manner */
+	s32 (*led_brightness_to_intensity)
+		(struct v4l2_flash *v4l2_flash, enum led_brightness);
+};
+
+/**
+ * struct v4l2_flash_config - V4L2 Flash sub-device initialization data
+ * @dev_name:			the name of the media entity,
+				unique in the system
+ * @torch_intensity:		constraints for the LED in torch mode
+ * @indicator_intensity:	constraints for the indicator LED
+ * @flash_faults:		bitmask of flash faults that the LED flash class
+				device can report; corresponding LED_FAULT* bit
+				definitions are available in the header file
+				<linux/led-class-flash.h>
+ * @has_external_strobe:	external strobe capability
+ */
+struct v4l2_flash_config {
+	char dev_name[32];
+	struct led_flash_setting torch_intensity;
+	struct led_flash_setting indicator_intensity;
+	u32 flash_faults;
+	unsigned int has_external_strobe:1;
+};
+
+/**
+ * struct v4l2_flash - Flash sub-device context
+ * @fled_cdev:		LED flash class device controlled by this sub-device
+ * @iled_cdev:		LED class device representing indicator LED associated
+ *			with the LED flash class device
+ * @ops:		V4L2 specific flash ops
+ * @sd:			V4L2 sub-device
+ * @hdl:		flash controls handler
+ * @ctrls:		array of pointers to controls, whose values define
+ *			the sub-device state
+ */
+struct v4l2_flash {
+	struct led_classdev_flash *fled_cdev;
+	struct led_classdev_flash *iled_cdev;
+	const struct v4l2_flash_ops *ops;
+
+	struct v4l2_subdev sd;
+	struct v4l2_ctrl_handler hdl;
+	struct v4l2_ctrl **ctrls;
+};
+
+static inline struct v4l2_flash *v4l2_subdev_to_v4l2_flash(
+							struct v4l2_subdev *sd)
+{
+	return container_of(sd, struct v4l2_flash, sd);
+}
+
+static inline struct v4l2_flash *v4l2_ctrl_to_v4l2_flash(struct v4l2_ctrl *c)
+{
+	return container_of(c->handler, struct v4l2_flash, hdl);
+}
+
+#if IS_ENABLED(CONFIG_V4L2_FLASH_LED_CLASS)
+/**
+ * v4l2_flash_init - initialize V4L2 flash led sub-device
+ * @dev:	flash device, e.g. an I2C device
+ * @of_node:	of_node of the LED, may be NULL if the same as device's
+ * @fled_cdev:	LED flash class device to wrap
+ * @iled_cdev:	LED flash class device representing indicator LED associated
+ *		with fled_cdev, may be NULL
+ * @flash_ops:	V4L2 Flash device ops
+ * @config:	initialization data for V4L2 Flash sub-device
+ *
+ * Create V4L2 Flash sub-device wrapping given LED subsystem device.
+ *
+ * Returns: A valid pointer, or, when an error occurs, the return
+ * value is encoded using ERR_PTR(). Use IS_ERR() to check and
+ * PTR_ERR() to obtain the numeric return value.
+ */
+struct v4l2_flash *v4l2_flash_init(
+	struct device *dev, struct device_node *of_node,
+	struct led_classdev_flash *fled_cdev,
+	struct led_classdev_flash *iled_cdev,
+	const struct v4l2_flash_ops *ops,
+	struct v4l2_flash_config *config);
+
+/**
+ * v4l2_flash_release - release V4L2 Flash sub-device
+ * @flash: the V4L2 Flash sub-device to release
+ *
+ * Release V4L2 Flash sub-device.
+ */
+void v4l2_flash_release(struct v4l2_flash *v4l2_flash);
+
+#else
+static inline struct v4l2_flash *v4l2_flash_init(
+	struct device *dev, struct device_node *of_node,
+	struct led_classdev_flash *fled_cdev,
+	struct led_classdev_flash *iled_cdev,
+	const struct v4l2_flash_ops *ops,
+	struct v4l2_flash_config *config)
+{
+	return NULL;
+}
+
+static inline void v4l2_flash_release(struct v4l2_flash *v4l2_flash)
+{
+}
+#endif /* CONFIG_V4L2_FLASH_LED_CLASS */
+
+#endif /* _V4L2_FLASH_H */

include/media/v4l2-subdev.h

@@ -605,6 +605,8 @@ struct v4l2_subdev {
 	struct video_device *devnode;
 	/* pointer to the physical device, if any */
 	struct device *dev;
+	/* The device_node of the subdev, usually the same as dev->of_node. */
+	struct device_node *of_node;
 	/* Links this subdev to a global subdev_list or @notifier->done list. */
 	struct list_head async_list;
 	/* Pointer to respective struct v4l2_async_subdev. */