USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support

Signed-off-by: Liu Junliang <liujunliang_ljl@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/usb/Kconfig

@@ -292,6 +292,22 @@ config USB_NET_SR9700
 	  This option adds support for CoreChip-sz SR9700 based USB 1.1
 	  10/100 Ethernet adapters.
 
+config USB_NET_SR9800
+	tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices"
+	depends on USB_USBNET
+	select CRC32
+	default y
+	---help---
+	  Say Y if you want to use one of the following 100Mbps USB Ethernet
+	  device based on the CoreChip-sz SR9800 chip.
+
+	  This driver makes the adapter appear as a normal Ethernet interface,
+	  typically on eth0, if it is the only ethernet device, or perhaps on
+	  eth1, if you have a PCI or ISA ethernet card installed.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sr9800.
+
 config USB_NET_SMSC75XX
 	tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
 	depends on USB_USBNET

drivers/net/usb/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_USB_NET_CDCETHER)	+= cdc_ether.o r815x.o
 obj-$(CONFIG_USB_NET_CDC_EEM)	+= cdc_eem.o
 obj-$(CONFIG_USB_NET_DM9601)	+= dm9601.o
 obj-$(CONFIG_USB_NET_SR9700)	+= sr9700.o
+obj-$(CONFIG_USB_NET_SR9800)	+= sr9800.o
 obj-$(CONFIG_USB_NET_SMSC75XX)	+= smsc75xx.o
 obj-$(CONFIG_USB_NET_SMSC95XX)	+= smsc95xx.o
 obj-$(CONFIG_USB_NET_GL620A)	+= gl620a.o

drivers/net/usb/sr9800.h

+/* CoreChip-sz SR9800 one chip USB 2.0 Ethernet Devices
+ *
+ * Author : Liu Junliang <liujunliang_ljl@163.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef	_SR9800_H
+#define	_SR9800_H
+
+/* SR9800 spec. command table on Linux Platform */
+
+/* command : Software Station Management Control Reg */
+#define SR_CMD_SET_SW_MII		0x06
+/* command : PHY Read Reg */
+#define SR_CMD_READ_MII_REG		0x07
+/* command : PHY Write Reg */
+#define SR_CMD_WRITE_MII_REG		0x08
+/* command : Hardware Station Management Control Reg */
+#define SR_CMD_SET_HW_MII		0x0a
+/* command : SROM Read Reg */
+#define SR_CMD_READ_EEPROM		0x0b
+/* command : SROM Write Reg */
+#define SR_CMD_WRITE_EEPROM		0x0c
+/* command : SROM Write Enable Reg */
+#define SR_CMD_WRITE_ENABLE		0x0d
+/* command : SROM Write Disable Reg */
+#define SR_CMD_WRITE_DISABLE		0x0e
+/* command : RX Control Read Reg */
+#define SR_CMD_READ_RX_CTL		0x0f
+#define		SR_RX_CTL_PRO			(1 << 0)
+#define		SR_RX_CTL_AMALL			(1 << 1)
+#define		SR_RX_CTL_SEP			(1 << 2)
+#define		SR_RX_CTL_AB			(1 << 3)
+#define		SR_RX_CTL_AM			(1 << 4)
+#define		SR_RX_CTL_AP			(1 << 5)
+#define		SR_RX_CTL_ARP			(1 << 6)
+#define		SR_RX_CTL_SO			(1 << 7)
+#define		SR_RX_CTL_RH1M			(1 << 8)
+#define		SR_RX_CTL_RH2M			(1 << 9)
+#define		SR_RX_CTL_RH3M			(1 << 10)
+/* command : RX Control Write Reg */
+#define SR_CMD_WRITE_RX_CTL		0x10
+/* command : IPG0/IPG1/IPG2 Control Read Reg */
+#define SR_CMD_READ_IPG012		0x11
+/* command : IPG0/IPG1/IPG2 Control Write Reg */
+#define SR_CMD_WRITE_IPG012		0x12
+/* command : Node ID Read Reg */
+#define SR_CMD_READ_NODE_ID		0x13
+/* command : Node ID Write Reg */
+#define SR_CMD_WRITE_NODE_ID		0x14
+/* command : Multicast Filter Array Read Reg */
+#define	SR_CMD_READ_MULTI_FILTER	0x15
+/* command : Multicast Filter Array Write Reg */
+#define SR_CMD_WRITE_MULTI_FILTER	0x16
+/* command : Eth/HomePNA PHY Address Reg */
+#define SR_CMD_READ_PHY_ID		0x19
+/* command : Medium Status Read Reg */
+#define SR_CMD_READ_MEDIUM_STATUS	0x1a
+#define		SR_MONITOR_LINK			(1 << 1)
+#define		SR_MONITOR_MAGIC		(1 << 2)
+#define		SR_MONITOR_HSFS			(1 << 4)
+/* command : Medium Status Write Reg */
+#define SR_CMD_WRITE_MEDIUM_MODE	0x1b
+#define		SR_MEDIUM_GM			(1 << 0)
+#define		SR_MEDIUM_FD			(1 << 1)
+#define		SR_MEDIUM_AC			(1 << 2)
+#define		SR_MEDIUM_ENCK			(1 << 3)
+#define		SR_MEDIUM_RFC			(1 << 4)
+#define		SR_MEDIUM_TFC			(1 << 5)
+#define		SR_MEDIUM_JFE			(1 << 6)
+#define		SR_MEDIUM_PF			(1 << 7)
+#define		SR_MEDIUM_RE			(1 << 8)
+#define		SR_MEDIUM_PS			(1 << 9)
+#define		SR_MEDIUM_RSV			(1 << 10)
+#define		SR_MEDIUM_SBP			(1 << 11)
+#define		SR_MEDIUM_SM			(1 << 12)
+/* command : Monitor Mode Status Read Reg */
+#define SR_CMD_READ_MONITOR_MODE	0x1c
+/* command : Monitor Mode Status Write Reg */
+#define SR_CMD_WRITE_MONITOR_MODE	0x1d
+/* command : GPIO Status Read Reg */
+#define SR_CMD_READ_GPIOS		0x1e
+#define		SR_GPIO_GPO0EN		(1 << 0) /* GPIO0 Output enable */
+#define		SR_GPIO_GPO_0		(1 << 1) /* GPIO0 Output value */
+#define		SR_GPIO_GPO1EN		(1 << 2) /* GPIO1 Output enable */
+#define		SR_GPIO_GPO_1		(1 << 3) /* GPIO1 Output value */
+#define		SR_GPIO_GPO2EN		(1 << 4) /* GPIO2 Output enable */
+#define		SR_GPIO_GPO_2		(1 << 5) /* GPIO2 Output value */
+#define		SR_GPIO_RESERVED	(1 << 6) /* Reserved */
+#define		SR_GPIO_RSE		(1 << 7) /* Reload serial EEPROM */
+/* command : GPIO Status Write Reg */
+#define SR_CMD_WRITE_GPIOS		0x1f
+/* command : Eth PHY Power and Reset Control Reg */
+#define SR_CMD_SW_RESET			0x20
+#define		SR_SWRESET_CLEAR		0x00
+#define		SR_SWRESET_RR			(1 << 0)
+#define		SR_SWRESET_RT			(1 << 1)
+#define		SR_SWRESET_PRTE			(1 << 2)
+#define		SR_SWRESET_PRL			(1 << 3)
+#define		SR_SWRESET_BZ			(1 << 4)
+#define		SR_SWRESET_IPRL			(1 << 5)
+#define		SR_SWRESET_IPPD			(1 << 6)
+/* command : Software Interface Selection Status Read Reg */
+#define SR_CMD_SW_PHY_STATUS		0x21
+/* command : Software Interface Selection Status Write Reg */
+#define SR_CMD_SW_PHY_SELECT		0x22
+/* command : BULK in Buffer Size Reg */
+#define	SR_CMD_BULKIN_SIZE		0x2A
+/* command : LED_MUX Control Reg */
+#define	SR_CMD_LED_MUX			0x70
+#define		SR_LED_MUX_TX_ACTIVE		(1 << 0)
+#define		SR_LED_MUX_RX_ACTIVE		(1 << 1)
+#define		SR_LED_MUX_COLLISION		(1 << 2)
+#define		SR_LED_MUX_DUP_COL		(1 << 3)
+#define		SR_LED_MUX_DUP			(1 << 4)
+#define		SR_LED_MUX_SPEED		(1 << 5)
+#define		SR_LED_MUX_LINK_ACTIVE		(1 << 6)
+#define		SR_LED_MUX_LINK			(1 << 7)
+
+/* Register Access Flags */
+#define SR_REQ_RD_REG   (USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE)
+#define SR_REQ_WR_REG   (USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE)
+
+/* Multicast Filter Array size & Max Number */
+#define	SR_MCAST_FILTER_SIZE		8
+#define	SR_MAX_MCAST			64
+
+/* IPG0/1/2 Default Value */
+#define	SR9800_IPG0_DEFAULT		0x15
+#define	SR9800_IPG1_DEFAULT		0x0c
+#define	SR9800_IPG2_DEFAULT		0x12
+
+/* Medium Status Default Mode */
+#define SR9800_MEDIUM_DEFAULT	\
+	(SR_MEDIUM_FD | SR_MEDIUM_RFC | \
+	 SR_MEDIUM_TFC | SR_MEDIUM_PS | \
+	 SR_MEDIUM_AC | SR_MEDIUM_RE)
+
+/* RX Control Default Setting */
+#define SR_DEFAULT_RX_CTL	\
+	(SR_RX_CTL_SO | SR_RX_CTL_AB | SR_RX_CTL_RH1M)
+
+/* EEPROM Magic Number & EEPROM Size */
+#define SR_EEPROM_MAGIC			0xdeadbeef
+#define SR9800_EEPROM_LEN		0xff
+
+/* SR9800 Driver Version and Driver Name */
+#define DRIVER_VERSION			"11-Nov-2013"
+#define DRIVER_NAME			"CoreChips"
+#define	DRIVER_FLAG		\
+	(FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |  FLAG_MULTI_PACKET)
+
+/* SR9800 BULKIN Buffer Size */
+#define SR9800_MAX_BULKIN_2K		0
+#define SR9800_MAX_BULKIN_4K		1
+#define SR9800_MAX_BULKIN_6K		2
+#define SR9800_MAX_BULKIN_8K		3
+#define SR9800_MAX_BULKIN_16K		4
+#define SR9800_MAX_BULKIN_20K		5
+#define SR9800_MAX_BULKIN_24K		6
+#define SR9800_MAX_BULKIN_32K		7
+
+struct {unsigned short size, byte_cnt, threshold; } SR9800_BULKIN_SIZE[] = {
+	/* 2k */
+	{2048, 0x8000, 0x8001},
+	/* 4k */
+	{4096, 0x8100, 0x8147},
+	/* 6k */
+	{6144, 0x8200, 0x81EB},
+	/* 8k */
+	{8192, 0x8300, 0x83D7},
+	/* 16 */
+	{16384, 0x8400, 0x851E},
+	/* 20k */
+	{20480, 0x8500, 0x8666},
+	/* 24k */
+	{24576, 0x8600, 0x87AE},
+	/* 32k */
+	{32768, 0x8700, 0x8A3D},
+};
+
+/* This structure cannot exceed sizeof(unsigned long [5]) AKA 20 bytes */
+struct sr_data {
+	u8 multi_filter[SR_MCAST_FILTER_SIZE];
+	u8 mac_addr[ETH_ALEN];
+	u8 phymode;
+	u8 ledmode;
+	u8 eeprom_len;
+};
+
+struct sr9800_int_data {
+	__le16 res1;
+	u8 link;
+	__le16 res2;
+	u8 status;
+	__le16 res3;
+} __packed;
+
+#endif	/* _SR9800_H */