Commit 19c54468 authored by Freeman Liu's avatar Freeman Liu Committed by Greg Kroah-Hartman

nvmem: Add Spreadtrum SC27XX efuse support

This patch add the efuse driver which is embeded in Spreadtrum SC27XX
series PMICs. The sc27xx efuse contains 32 blocks and each block's
data width is 16 bits.
Signed-off-by: default avatarFreeman Liu <freeman.liu@spreadtrum.com>
Signed-off-by: default avatarBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: default avatarSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 3eb93e08
...@@ -181,4 +181,15 @@ config RAVE_SP_EEPROM ...@@ -181,4 +181,15 @@ config RAVE_SP_EEPROM
help help
Say y here to enable Rave SP EEPROM support. Say y here to enable Rave SP EEPROM support.
config SC27XX_EFUSE
tristate "Spreadtrum SC27XX eFuse Support"
depends on MFD_SC27XX_PMIC || COMPILE_TEST
depends on HAS_IOMEM
help
This is a simple driver to dump specified values of Spreadtrum
SC27XX PMICs from eFuse.
This driver can also be built as a module. If so, the module
will be called nvmem-sc27xx-efuse.
endif endif
...@@ -39,4 +39,5 @@ obj-$(CONFIG_NVMEM_SNVS_LPGPR) += nvmem_snvs_lpgpr.o ...@@ -39,4 +39,5 @@ obj-$(CONFIG_NVMEM_SNVS_LPGPR) += nvmem_snvs_lpgpr.o
nvmem_snvs_lpgpr-y := snvs_lpgpr.o nvmem_snvs_lpgpr-y := snvs_lpgpr.o
obj-$(CONFIG_RAVE_SP_EEPROM) += nvmem-rave-sp-eeprom.o obj-$(CONFIG_RAVE_SP_EEPROM) += nvmem-rave-sp-eeprom.o
nvmem-rave-sp-eeprom-y := rave-sp-eeprom.o nvmem-rave-sp-eeprom-y := rave-sp-eeprom.o
obj-$(CONFIG_SC27XX_EFUSE) += nvmem-sc27xx-efuse.o
nvmem-sc27xx-efuse-y := sc27xx-efuse.o
// SPDX-License-Identifier: GPL-2.0
// Copyright (C) 2018 Spreadtrum Communications Inc.
#include <linux/hwspinlock.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/nvmem-provider.h>
/* PMIC global registers definition */
#define SC27XX_MODULE_EN 0xc08
#define SC27XX_EFUSE_EN BIT(6)
/* Efuse controller registers definition */
#define SC27XX_EFUSE_GLB_CTRL 0x0
#define SC27XX_EFUSE_DATA_RD 0x4
#define SC27XX_EFUSE_DATA_WR 0x8
#define SC27XX_EFUSE_BLOCK_INDEX 0xc
#define SC27XX_EFUSE_MODE_CTRL 0x10
#define SC27XX_EFUSE_STATUS 0x14
#define SC27XX_EFUSE_WR_TIMING_CTRL 0x20
#define SC27XX_EFUSE_RD_TIMING_CTRL 0x24
#define SC27XX_EFUSE_EFUSE_DEB_CTRL 0x28
/* Mask definition for SC27XX_EFUSE_BLOCK_INDEX register */
#define SC27XX_EFUSE_BLOCK_MASK GENMASK(4, 0)
/* Bits definitions for SC27XX_EFUSE_MODE_CTRL register */
#define SC27XX_EFUSE_PG_START BIT(0)
#define SC27XX_EFUSE_RD_START BIT(1)
#define SC27XX_EFUSE_CLR_RDDONE BIT(2)
/* Bits definitions for SC27XX_EFUSE_STATUS register */
#define SC27XX_EFUSE_PGM_BUSY BIT(0)
#define SC27XX_EFUSE_READ_BUSY BIT(1)
#define SC27XX_EFUSE_STANDBY BIT(2)
#define SC27XX_EFUSE_GLOBAL_PROT BIT(3)
#define SC27XX_EFUSE_RD_DONE BIT(4)
/* Block number and block width (bytes) definitions */
#define SC27XX_EFUSE_BLOCK_MAX 32
#define SC27XX_EFUSE_BLOCK_WIDTH 2
/* Timeout (ms) for the trylock of hardware spinlocks */
#define SC27XX_EFUSE_HWLOCK_TIMEOUT 5000
/* Timeout (us) of polling the status */
#define SC27XX_EFUSE_POLL_TIMEOUT 3000000
#define SC27XX_EFUSE_POLL_DELAY_US 10000
struct sc27xx_efuse {
struct device *dev;
struct regmap *regmap;
struct hwspinlock *hwlock;
struct mutex mutex;
u32 base;
};
/*
* On Spreadtrum platform, we have multi-subsystems will access the unique
* efuse controller, so we need one hardware spinlock to synchronize between
* the multiple subsystems.
*/
static int sc27xx_efuse_lock(struct sc27xx_efuse *efuse)
{
int ret;
mutex_lock(&efuse->mutex);
ret = hwspin_lock_timeout_raw(efuse->hwlock,
SC27XX_EFUSE_HWLOCK_TIMEOUT);
if (ret) {
dev_err(efuse->dev, "timeout to get the hwspinlock\n");
mutex_unlock(&efuse->mutex);
return ret;
}
return 0;
}
static void sc27xx_efuse_unlock(struct sc27xx_efuse *efuse)
{
hwspin_unlock_raw(efuse->hwlock);
mutex_unlock(&efuse->mutex);
}
static int sc27xx_efuse_poll_status(struct sc27xx_efuse *efuse, u32 bits)
{
int ret;
u32 val;
ret = regmap_read_poll_timeout(efuse->regmap,
efuse->base + SC27XX_EFUSE_STATUS,
val, (val & bits),
SC27XX_EFUSE_POLL_DELAY_US,
SC27XX_EFUSE_POLL_TIMEOUT);
if (ret) {
dev_err(efuse->dev, "timeout to update the efuse status\n");
return ret;
}
return 0;
}
static int sc27xx_efuse_read(void *context, u32 offset, void *val, size_t bytes)
{
struct sc27xx_efuse *efuse = context;
u32 buf;
int ret;
if (offset > SC27XX_EFUSE_BLOCK_MAX || bytes > SC27XX_EFUSE_BLOCK_WIDTH)
return -EINVAL;
ret = sc27xx_efuse_lock(efuse);
if (ret)
return ret;
/* Enable the efuse controller. */
ret = regmap_update_bits(efuse->regmap, SC27XX_MODULE_EN,
SC27XX_EFUSE_EN, SC27XX_EFUSE_EN);
if (ret)
goto unlock_efuse;
/*
* Before reading, we should ensure the efuse controller is in
* standby state.
*/
ret = sc27xx_efuse_poll_status(efuse, SC27XX_EFUSE_STANDBY);
if (ret)
goto disable_efuse;
/* Set the block address to be read. */
ret = regmap_write(efuse->regmap,
efuse->base + SC27XX_EFUSE_BLOCK_INDEX,
offset & SC27XX_EFUSE_BLOCK_MASK);
if (ret)
goto disable_efuse;
/* Start reading process from efuse memory. */
ret = regmap_update_bits(efuse->regmap,
efuse->base + SC27XX_EFUSE_MODE_CTRL,
SC27XX_EFUSE_RD_START,
SC27XX_EFUSE_RD_START);
if (ret)
goto disable_efuse;
/*
* Polling the read done status to make sure the reading process
* is completed, that means the data can be read out now.
*/
ret = sc27xx_efuse_poll_status(efuse, SC27XX_EFUSE_RD_DONE);
if (ret)
goto disable_efuse;
/* Read data from efuse memory. */
ret = regmap_read(efuse->regmap, efuse->base + SC27XX_EFUSE_DATA_RD,
&buf);
if (ret)
goto disable_efuse;
/* Clear the read done flag. */
ret = regmap_update_bits(efuse->regmap,
efuse->base + SC27XX_EFUSE_MODE_CTRL,
SC27XX_EFUSE_CLR_RDDONE,
SC27XX_EFUSE_CLR_RDDONE);
disable_efuse:
/* Disable the efuse controller after reading. */
regmap_update_bits(efuse->regmap, SC27XX_MODULE_EN, SC27XX_EFUSE_EN, 0);
unlock_efuse:
sc27xx_efuse_unlock(efuse);
if (!ret)
memcpy(val, &buf, bytes);
return ret;
}
static int sc27xx_efuse_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct nvmem_config econfig = { };
struct nvmem_device *nvmem;
struct sc27xx_efuse *efuse;
int ret;
efuse = devm_kzalloc(&pdev->dev, sizeof(*efuse), GFP_KERNEL);
if (!efuse)
return -ENOMEM;
efuse->regmap = dev_get_regmap(pdev->dev.parent, NULL);
if (!efuse->regmap) {
dev_err(&pdev->dev, "failed to get efuse regmap\n");
return -ENODEV;
}
ret = of_property_read_u32(np, "reg", &efuse->base);
if (ret) {
dev_err(&pdev->dev, "failed to get efuse base address\n");
return ret;
}
ret = of_hwspin_lock_get_id(np, 0);
if (ret < 0) {
dev_err(&pdev->dev, "failed to get hwspinlock id\n");
return ret;
}
efuse->hwlock = hwspin_lock_request_specific(ret);
if (!efuse->hwlock) {
dev_err(&pdev->dev, "failed to request hwspinlock\n");
return -ENXIO;
}
mutex_init(&efuse->mutex);
efuse->dev = &pdev->dev;
platform_set_drvdata(pdev, efuse);
econfig.stride = 1;
econfig.word_size = 1;
econfig.read_only = true;
econfig.name = "sc27xx-efuse";
econfig.size = SC27XX_EFUSE_BLOCK_MAX * SC27XX_EFUSE_BLOCK_WIDTH;
econfig.reg_read = sc27xx_efuse_read;
econfig.priv = efuse;
econfig.dev = &pdev->dev;
nvmem = devm_nvmem_register(&pdev->dev, &econfig);
if (IS_ERR(nvmem)) {
dev_err(&pdev->dev, "failed to register nvmem config\n");
hwspin_lock_free(efuse->hwlock);
return PTR_ERR(nvmem);
}
return 0;
}
static int sc27xx_efuse_remove(struct platform_device *pdev)
{
struct sc27xx_efuse *efuse = platform_get_drvdata(pdev);
hwspin_lock_free(efuse->hwlock);
return 0;
}
static const struct of_device_id sc27xx_efuse_of_match[] = {
{ .compatible = "sprd,sc2731-efuse" },
{ }
};
static struct platform_driver sc27xx_efuse_driver = {
.probe = sc27xx_efuse_probe,
.remove = sc27xx_efuse_remove,
.driver = {
.name = "sc27xx-efuse",
.of_match_table = sc27xx_efuse_of_match,
},
};
module_platform_driver(sc27xx_efuse_driver);
MODULE_AUTHOR("Freeman Liu <freeman.liu@spreadtrum.com>");
MODULE_DESCRIPTION("Spreadtrum SC27xx efuse driver");
MODULE_LICENSE("GPL v2");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment