Device tree aware EMAC driver

Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.

This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).

This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Documentation/powerpc/booting-without-of.txt

@@ -1824,6 +1824,162 @@ platforms are moved over to use the flattened-device-tree model.
 		fsl,has-rstcr;
 	};
 
+
+    h) 4xx/Axon EMAC ethernet nodes
+
+    The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
+    the Axon bridge.  To operate this needs to interact with a ths
+    special McMAL DMA controller, and sometimes an RGMII or ZMII
+    interface.  In addition to the nodes and properties described
+    below, the node for the OPB bus on which the EMAC sits must have a
+    correct clock-frequency property.
+
+      i) The EMAC node itself
+
+    Required properties:
+    - device_type       : "network"
+
+    - compatible        : compatible list, contains 2 entries, first is
+			  "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
+			  405gp, Axon) and second is either "ibm,emac" or
+			  "ibm,emac4".  For Axon, thus, we have: "ibm,emac-axon",
+			  "ibm,emac4"
+    - interrupts        : <interrupt mapping for EMAC IRQ and WOL IRQ>
+    - interrupt-parent  : optional, if needed for interrupt mapping
+    - reg               : <registers mapping>
+    - local-mac-address : 6 bytes, MAC address
+    - mal-device        : phandle of the associated McMAL node
+    - mal-tx-channel    : 1 cell, index of the tx channel on McMAL associated
+			  with this EMAC
+    - mal-rx-channel    : 1 cell, index of the rx channel on McMAL associated
+			  with this EMAC
+    - cell-index        : 1 cell, hardware index of the EMAC cell on a given
+			  ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
+			  each Axon chip)
+    - max-frame-size    : 1 cell, maximum frame size supported in bytes
+    - rx-fifo-size      : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
+			  operations.
+			  For Axon, 2048
+    - tx-fifo-size      : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
+			  operations.
+			  For Axon, 2048.
+    - fifo-entry-size   : 1 cell, size of a fifo entry (used to calculate
+			  thresholds).
+			  For Axon, 0x00000010
+    - mal-burst-size    : 1 cell, MAL burst size (used to calculate thresholds)
+			  in bytes.
+			  For Axon, 0x00000100 (I think ...)
+    - phy-mode          : string, mode of operations of the PHY interface.
+			  Supported values are: "mii", "rmii", "smii", "rgmii",
+			  "tbi", "gmii", rtbi", "sgmii".
+			  For Axon on CAB, it is "rgmii"
+    - mdio-device       : 1 cell, required iff using shared MDIO registers
+			  (440EP).  phandle of the EMAC to use to drive the
+			  MDIO lines for the PHY used by this EMAC.
+    - zmii-device       : 1 cell, required iff connected to a ZMII.  phandle of
+			  the ZMII device node
+    - zmii-channel      : 1 cell, required iff connected to a ZMII.  Which ZMII
+			  channel or 0xffffffff if ZMII is only used for MDIO.
+    - rgmii-device      : 1 cell, required iff connected to an RGMII. phandle
+			  of the RGMII device node.
+			  For Axon: phandle of plb5/plb4/opb/rgmii
+    - rgmii-channel     : 1 cell, required iff connected to an RGMII.  Which
+			  RGMII channel is used by this EMAC.
+			  Fox Axon: present, whatever value is appropriate for each
+			  EMAC, that is the content of the current (bogus) "phy-port"
+			  property.
+
+    Recommended properties:
+    - linux,network-index : This is the intended "index" of this
+      network device.  This is used by the bootwrapper to interpret
+      MAC addresses passed by the firmware when no information other
+      than indices is available to associate an address with a device.
+
+    Optional properties:
+    - phy-address       : 1 cell, optional, MDIO address of the PHY. If absent,
+			  a search is performed.
+    - phy-map           : 1 cell, optional, bitmap of addresses to probe the PHY
+			  for, used if phy-address is absent. bit 0x00000001 is
+			  MDIO address 0.
+			  For Axon it can be absent, thouugh my current driver
+			  doesn't handle phy-address yet so for now, keep
+			  0x00ffffff in it.
+    - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
+			  operations (if absent the value is the same as
+			  rx-fifo-size).  For Axon, either absent or 2048.
+    - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
+			  operations (if absent the value is the same as
+			  tx-fifo-size). For Axon, either absent or 2048.
+    - tah-device        : 1 cell, optional. If connected to a TAH engine for
+			  offload, phandle of the TAH device node.
+    - tah-channel       : 1 cell, optional. If appropriate, channel used on the
+			  TAH engine.
+
+    Example:
+
+	EMAC0: ethernet@40000800 {
+		linux,network-index = <0>;
+		device_type = "network";
+		compatible = "ibm,emac-440gp", "ibm,emac";
+		interrupt-parent = <&UIC1>;
+		interrupts = <1c 4 1d 4>;
+		reg = <40000800 70>;
+		local-mac-address = [00 04 AC E3 1B 1E];
+		mal-device = <&MAL0>;
+		mal-tx-channel = <0 1>;
+		mal-rx-channel = <0>;
+		cell-index = <0>;
+		max-frame-size = <5dc>;
+		rx-fifo-size = <1000>;
+		tx-fifo-size = <800>;
+		phy-mode = "rmii";
+		phy-map = <00000001>;
+		zmii-device = <&ZMII0>;
+		zmii-channel = <0>;
+	};
+
+      ii) McMAL node
+
+    Required properties:
+    - device_type        : "dma-controller"
+    - compatible         : compatible list, containing 2 entries, first is
+			   "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
+			   emac) and the second is either "ibm,mcmal" or
+			   "ibm,mcmal2".
+			   For Axon, "ibm,mcmal-axon","ibm,mcmal2"
+    - interrupts         : <interrupt mapping for the MAL interrupts sources:
+                           5 sources: tx_eob, rx_eob, serr, txde, rxde>.
+                           For Axon: This is _different_ from the current
+			   firmware.  We use the "delayed" interrupts for txeob
+			   and rxeob. Thus we end up with mapping those 5 MPIC
+			   interrupts, all level positive sensitive: 10, 11, 32,
+			   33, 34 (in decimal)
+    - dcr-reg            : < DCR registers range >
+    - dcr-parent         : if needed for dcr-reg
+    - num-tx-chans       : 1 cell, number of Tx channels
+    - num-rx-chans       : 1 cell, number of Rx channels
+
+      iii) ZMII node
+
+    Required properties:
+    - compatible         : compatible list, containing 2 entries, first is
+			   "ibm,zmii-CHIP" where CHIP is the host ASIC (like
+			   EMAC) and the second is "ibm,zmii".
+			   For Axon, there is no ZMII node.
+    - reg                : <registers mapping>
+
+      iv) RGMII node
+
+    Required properties:
+    - compatible         : compatible list, containing 2 entries, first is
+			   "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
+			   EMAC) and the second is "ibm,rgmii".
+                           For Axon, "ibm,rgmii-axon","ibm,rgmii"
+    - reg                : <registers mapping>
+    - revision           : as provided by the RGMII new version register if
+			   available.
+			   For Axon: 0x0000012a
+
    More devices will be defined as this spec matures.
 
 VII - Specifying interrupt information for devices

arch/powerpc/platforms/44x/Kconfig

@@ -38,8 +38,7 @@ config 440EP
 
 config 440GP
 	bool
-# Disabled until the new EMAC Driver is merged.
-#	select IBM_NEW_EMAC_ZMII
+	select IBM_NEW_EMAC_ZMII
 
 config 440GX
 	bool

arch/powerpc/platforms/cell/Kconfig

@@ -10,6 +10,10 @@ config PPC_CELL_NATIVE
 	select PPC_INDIRECT_IO
 	select PPC_NATIVE
 	select MPIC
+	select IBM_NEW_EMAC_EMAC4
+	select IBM_NEW_EMAC_RGMII
+	select IBM_NEW_EMAC_ZMII #test only
+	select IBM_NEW_EMAC_TAH  #test only
 	default n
 
 config PPC_IBM_CELL_BLADE

drivers/net/Kconfig

@@ -1247,75 +1247,8 @@ config IBMVETH
 	  <file:Documentation/networking/net-modules.txt>. The module will
 	  be called ibmveth.
 
-config IBM_EMAC
-	tristate "PowerPC 4xx on-chip Ethernet support"
-	depends on 4xx && !PPC_MERGE
-	help
-	  This driver supports the PowerPC 4xx EMAC family of on-chip
-          Ethernet controllers.
-
-config IBM_EMAC_RXB
-	int "Number of receive buffers"
-	depends on IBM_EMAC
-	default "128"
-
-config IBM_EMAC_TXB
-	int "Number of transmit buffers"
-	depends on IBM_EMAC
-	default "64"
-
-config IBM_EMAC_POLL_WEIGHT
-	int "MAL NAPI polling weight"
-	depends on IBM_EMAC
-	default "32"
-
-config IBM_EMAC_RX_COPY_THRESHOLD
-	int "RX skb copy threshold (bytes)"
-	depends on IBM_EMAC
-	default "256"
-
-config IBM_EMAC_RX_SKB_HEADROOM
-	int "Additional RX skb headroom (bytes)"
-	depends on IBM_EMAC
-	default "0"
-	help
-	  Additional receive skb headroom. Note, that driver
-	  will always reserve at least 2 bytes to make IP header
-	  aligned, so usually there is no need to add any additional
-	  headroom.
-	  
-	  If unsure, set to 0.
-
-config IBM_EMAC_PHY_RX_CLK_FIX
-	bool "PHY Rx clock workaround"
-	depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
-	help
-	  Enable this if EMAC attached to a PHY which doesn't generate
-	  RX clock if there is no link, if this is the case, you will 
-	  see "TX disable timeout" or "RX disable timeout" in the system
-	  log.
-	  
-	  If unsure, say N.
-
-config IBM_EMAC_DEBUG
-	bool "Debugging"
-	depends on IBM_EMAC
-	default n
-
-config IBM_EMAC_ZMII
-	bool
-	depends on IBM_EMAC && (NP405H || NP405L || 44x)
-	default y
-
-config IBM_EMAC_RGMII
-	bool
-	depends on IBM_EMAC && 440GX
-	default y
-		
-config IBM_EMAC_TAH
-	bool
-	depends on IBM_EMAC && 440GX
-	default y
+source "drivers/net/ibm_emac/Kconfig"
+source "drivers/net/ibm_newemac/Kconfig"
 
 config NET_PCI
 	bool "EISA, VLB, PCI and on board controllers"

drivers/net/Makefile

@@ -5,6 +5,7 @@
 obj-$(CONFIG_E1000) += e1000/
 obj-$(CONFIG_E1000E) += e1000e/
 obj-$(CONFIG_IBM_EMAC) += ibm_emac/
+obj-$(CONFIG_IBM_NEW_EMAC) += ibm_newemac/
 obj-$(CONFIG_IXGBE) += ixgbe/
 obj-$(CONFIG_IXGB) += ixgb/
 obj-$(CONFIG_IP1000) += ipg.o

drivers/net/ibm_emac/Kconfig

+config IBM_EMAC
+	tristate "PowerPC 4xx on-chip Ethernet support"
+	depends on 4xx && !PPC_MERGE
+	help
+	  This driver supports the PowerPC 4xx EMAC family of on-chip
+          Ethernet controllers.
+
+config IBM_EMAC_RXB
+	int "Number of receive buffers"
+	depends on IBM_EMAC
+	default "128"
+
+config IBM_EMAC_TXB
+	int "Number of transmit buffers"
+	depends on IBM_EMAC
+	default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+	int "MAL NAPI polling weight"
+	depends on IBM_EMAC
+	default "32"
+
+config IBM_EMAC_RX_COPY_THRESHOLD
+	int "RX skb copy threshold (bytes)"
+	depends on IBM_EMAC
+	default "256"
+
+config IBM_EMAC_RX_SKB_HEADROOM
+	int "Additional RX skb headroom (bytes)"
+	depends on IBM_EMAC
+	default "0"
+	help
+	  Additional receive skb headroom. Note, that driver
+	  will always reserve at least 2 bytes to make IP header
+	  aligned, so usually there is no need to add any additional
+	  headroom.
+
+	  If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+	bool "PHY Rx clock workaround"
+	depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+	help
+	  Enable this if EMAC attached to a PHY which doesn't generate
+	  RX clock if there is no link, if this is the case, you will
+	  see "TX disable timeout" or "RX disable timeout" in the system
+	  log.
+
+	  If unsure, say N.
+
+config IBM_EMAC_DEBUG
+	bool "Debugging"
+	depends on IBM_EMAC
+	default n
+
+config IBM_EMAC_ZMII
+	bool
+	depends on IBM_EMAC && (NP405H || NP405L || 44x)
+	default y
+
+config IBM_EMAC_RGMII
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
+
+config IBM_EMAC_TAH
+	bool
+	depends on IBM_EMAC && 440GX
+	default y
+

drivers/net/ibm_newemac/Kconfig

+config IBM_NEW_EMAC
+	tristate "IBM EMAC Ethernet support"
+	depends on PPC_DCR && PPC_MERGE
+	help
+	  This driver supports the IBM EMAC family of Ethernet controllers
+	  typically found on 4xx embedded PowerPC chips, but also on the
+	  Axon southbridge for Cell.
+
+config IBM_NEW_EMAC_RXB
+	int "Number of receive buffers"
+	depends on IBM_NEW_EMAC
+	default "128"
+
+config IBM_NEW_EMAC_TXB
+	int "Number of transmit buffers"
+	depends on IBM_NEW_EMAC
+	default "64"
+
+config IBM_NEW_EMAC_POLL_WEIGHT
+	int "MAL NAPI polling weight"
+	depends on IBM_NEW_EMAC
+	default "32"
+
+config IBM_NEW_EMAC_RX_COPY_THRESHOLD
+	int "RX skb copy threshold (bytes)"
+	depends on IBM_NEW_EMAC
+	default "256"
+
+config IBM_NEW_EMAC_RX_SKB_HEADROOM
+	int "Additional RX skb headroom (bytes)"
+	depends on IBM_NEW_EMAC
+	default "0"
+	help
+	  Additional receive skb headroom. Note, that driver
+	  will always reserve at least 2 bytes to make IP header
+	  aligned, so usually there is no need to add any additional
+	  headroom.
+
+	  If unsure, set to 0.
+
+config IBM_NEW_EMAC_DEBUG
+	bool "Debugging"
+	depends on IBM_NEW_EMAC
+	default n
+
+# The options below has to be select'ed by the respective
+# processor types or platforms
+
+config IBM_NEW_EMAC_ZMII
+	bool
+	default n
+
+config IBM_NEW_EMAC_RGMII
+	bool
+	default n
+
+config IBM_NEW_EMAC_TAH
+	bool
+	default n
+
+config IBM_NEW_EMAC_EMAC4
+	bool
+	default n

drivers/net/ibm_newemac/Makefile

+#
+# Makefile for the PowerPC 4xx on-chip ethernet driver
+#
+
+obj-$(CONFIG_IBM_NEW_EMAC) += ibm_newemac.o
+
+ibm_newemac-y := mal.o core.o phy.o
+ibm_newemac-$(CONFIG_IBM_NEW_EMAC_ZMII) += zmii.o
+ibm_newemac-$(CONFIG_IBM_NEW_EMAC_RGMII) += rgmii.o
+ibm_newemac-$(CONFIG_IBM_NEW_EMAC_TAH) += tah.o
+ibm_newemac-$(CONFIG_IBM_NEW_EMAC_DEBUG) += debug.o

drivers/net/ibm_newemac/core.h

+/*
+ * drivers/net/ibm_newemac/core.h
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * Based on original work by
+ *      Armin Kuster <akuster@mvista.com>
+ * 	Johnnie Peters <jpeters@mvista.com>
+ *      Copyright 2000, 2001 MontaVista Softare Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __IBM_NEWEMAC_CORE_H
+#define __IBM_NEWEMAC_CORE_H
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/dma-mapping.h>
+#include <linux/spinlock.h>
+
+#include <asm/of_platform.h>
+#include <asm/io.h>
+#include <asm/dcr.h>
+
+#include "emac.h"
+#include "phy.h"
+#include "zmii.h"
+#include "rgmii.h"
+#include "mal.h"
+#include "tah.h"
+#include "debug.h"
+
+#define NUM_TX_BUFF			CONFIG_IBM_NEW_EMAC_TXB
+#define NUM_RX_BUFF			CONFIG_IBM_NEW_EMAC_RXB
+
+/* Simple sanity check */
+#if NUM_TX_BUFF > 256 || NUM_RX_BUFF > 256
+#error Invalid number of buffer descriptors (greater than 256)
+#endif
+
+#define EMAC_MIN_MTU			46
+
+/* Maximum L2 header length (VLAN tagged, no FCS) */
+#define EMAC_MTU_OVERHEAD		(6 * 2 + 2 + 4)
+
+/* RX BD size for the given MTU */
+static inline int emac_rx_size(int mtu)
+{
+	if (mtu > ETH_DATA_LEN)
+		return MAL_MAX_RX_SIZE;
+	else
+		return mal_rx_size(ETH_DATA_LEN + EMAC_MTU_OVERHEAD);
+}
+
+#define EMAC_DMA_ALIGN(x)		ALIGN((x), dma_get_cache_alignment())
+
+#define EMAC_RX_SKB_HEADROOM		\
+	EMAC_DMA_ALIGN(CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM)
+
+/* Size of RX skb for the given MTU */
+static inline int emac_rx_skb_size(int mtu)
+{
+	int size = max(mtu + EMAC_MTU_OVERHEAD, emac_rx_size(mtu));
+	return EMAC_DMA_ALIGN(size + 2) + EMAC_RX_SKB_HEADROOM;
+}
+
+/* RX DMA sync size */
+static inline int emac_rx_sync_size(int mtu)
+{
+	return EMAC_DMA_ALIGN(emac_rx_size(mtu) + 2);
+}
+
+/* Driver statistcs is split into two parts to make it more cache friendly:
+ *   - normal statistics (packet count, etc)
+ *   - error statistics
+ *
+ * When statistics is requested by ethtool, these parts are concatenated,
+ * normal one goes first.
+ *
+ * Please, keep these structures in sync with emac_stats_keys.
+ */
+
+/* Normal TX/RX Statistics */
+struct emac_stats {
+	u64 rx_packets;
+	u64 rx_bytes;
+	u64 tx_packets;
+	u64 tx_bytes;
+	u64 rx_packets_csum;
+	u64 tx_packets_csum;
+};
+
+/* Error statistics */
+struct emac_error_stats {
+	u64 tx_undo;
+
+	/* Software RX Errors */
+	u64 rx_dropped_stack;
+	u64 rx_dropped_oom;
+	u64 rx_dropped_error;
+	u64 rx_dropped_resize;
+	u64 rx_dropped_mtu;
+	u64 rx_stopped;
+	/* BD reported RX errors */
+	u64 rx_bd_errors;
+	u64 rx_bd_overrun;
+	u64 rx_bd_bad_packet;
+	u64 rx_bd_runt_packet;
+	u64 rx_bd_short_event;
+	u64 rx_bd_alignment_error;
+	u64 rx_bd_bad_fcs;
+	u64 rx_bd_packet_too_long;
+	u64 rx_bd_out_of_range;
+	u64 rx_bd_in_range;
+	/* EMAC IRQ reported RX errors */
+	u64 rx_parity;
+	u64 rx_fifo_overrun;
+	u64 rx_overrun;
+	u64 rx_bad_packet;
+	u64 rx_runt_packet;
+	u64 rx_short_event;
+	u64 rx_alignment_error;
+	u64 rx_bad_fcs;
+	u64 rx_packet_too_long;
+	u64 rx_out_of_range;
+	u64 rx_in_range;
+
+	/* Software TX Errors */
+	u64 tx_dropped;
+	/* BD reported TX errors */
+	u64 tx_bd_errors;
+	u64 tx_bd_bad_fcs;
+	u64 tx_bd_carrier_loss;
+	u64 tx_bd_excessive_deferral;
+	u64 tx_bd_excessive_collisions;
+	u64 tx_bd_late_collision;
+	u64 tx_bd_multple_collisions;
+	u64 tx_bd_single_collision;
+	u64 tx_bd_underrun;
+	u64 tx_bd_sqe;
+	/* EMAC IRQ reported TX errors */
+	u64 tx_parity;
+	u64 tx_underrun;
+	u64 tx_sqe;
+	u64 tx_errors;
+};
+
+#define EMAC_ETHTOOL_STATS_COUNT	((sizeof(struct emac_stats) + \
+					  sizeof(struct emac_error_stats)) \
+					 / sizeof(u64))
+
+struct emac_instance {
+	struct net_device		*ndev;
+	struct resource			rsrc_regs;
+	struct emac_regs		__iomem *emacp;
+	struct of_device		*ofdev;
+	struct device_node		**blist; /* bootlist entry */
+
+	/* MAL linkage */
+	u32				mal_ph;
+	struct of_device		*mal_dev;
+	u32				mal_rx_chan;
+	u32				mal_tx_chan;
+	struct mal_instance		*mal;
+	struct mal_commac		commac;
+
+	/* PHY infos */
+	u32				phy_mode;
+	u32				phy_map;
+	u32				phy_address;
+	u32				phy_feat_exc;
+	struct mii_phy			phy;
+	struct mutex			link_lock;
+	struct delayed_work		link_work;
+	int				link_polling;
+
+	/* Shared MDIO if any */
+	u32				mdio_ph;
+	struct of_device		*mdio_dev;
+	struct emac_instance		*mdio_instance;
+	struct mutex			mdio_lock;
+
+	/* ZMII infos if any */
+	u32				zmii_ph;
+	u32				zmii_port;
+	struct of_device		*zmii_dev;
+
+	/* RGMII infos if any */
+	u32				rgmii_ph;
+	u32				rgmii_port;
+	struct of_device		*rgmii_dev;
+
+	/* TAH infos if any */
+	u32				tah_ph;
+	u32				tah_port;
+	struct of_device		*tah_dev;
+
+	/* IRQs */
+	int				wol_irq;
+	int				emac_irq;
+
+	/* OPB bus frequency in Mhz */
+	u32				opb_bus_freq;
+
+	/* Cell index within an ASIC (for clk mgmnt) */
+	u32				cell_index;
+
+	/* Max supported MTU */
+	u32				max_mtu;
+
+	/* Feature bits (from probe table) */
+	unsigned int			features;
+
+	/* Tx and Rx fifo sizes & other infos in bytes */
+	u32				tx_fifo_size;
+	u32				tx_fifo_size_gige;
+	u32				rx_fifo_size;
+	u32				rx_fifo_size_gige;
+	u32				fifo_entry_size;
+	u32				mal_burst_size; /* move to MAL ? */
+
+	/* Descriptor management
+	 */
+	struct mal_descriptor		*tx_desc;
+	int				tx_cnt;
+	int				tx_slot;
+	int				ack_slot;
+
+	struct mal_descriptor		*rx_desc;
+	int				rx_slot;
+	struct sk_buff			*rx_sg_skb;	/* 1 */
+	int 				rx_skb_size;
+	int				rx_sync_size;
+
+	struct sk_buff			*tx_skb[NUM_TX_BUFF];
+	struct sk_buff			*rx_skb[NUM_RX_BUFF];
+
+	/* Stats
+	 */
+	struct emac_error_stats		estats;
+	struct net_device_stats		nstats;
+	struct emac_stats 		stats;
+
+	/* Misc
+	 */
+	int				reset_failed;
+	int				stop_timeout;	/* in us */
+	int				no_mcast;
+	int				mcast_pending;
+	struct work_struct		reset_work;
+	spinlock_t			lock;
+};
+
+/*
+ * Features of various EMAC implementations
+ */
+
+/*
+ * No flow control on 40x according to the original driver
+ */
+#define EMAC_FTR_NO_FLOW_CONTROL_40x	0x00000001
+/*
+ * Cell is an EMAC4
+ */
+#define EMAC_FTR_EMAC4			0x00000002
+/*
+ * For the 440SPe, AMCC inexplicably changed the polarity of
+ * the "operation complete" bit in the MII control register.
+ */
+#define EMAC_FTR_STACR_OC_INVERT	0x00000004
+/*
+ * Set if we have a TAH.
+ */
+#define EMAC_FTR_HAS_TAH		0x00000008
+/*
+ * Set if we have a ZMII.
+ */
+#define EMAC_FTR_HAS_ZMII		0x00000010
+/*
+ * Set if we have a RGMII.
+ */
+#define EMAC_FTR_HAS_RGMII		0x00000020
+/*
+ * Set if we have axon-type STACR
+ */
+#define EMAC_FTR_HAS_AXON_STACR		0x00000040
+
+
+/* Right now, we don't quite handle the always/possible masks on the
+ * most optimal way as we don't have a way to say something like
+ * always EMAC4. Patches welcome.
+ */
+enum {
+	EMAC_FTRS_ALWAYS	= 0,
+
+	EMAC_FTRS_POSSIBLE	=
+#ifdef CONFIG_IBM_NEW_EMAC_EMAC4
+	    EMAC_FTR_EMAC4	| EMAC_FTR_HAS_AXON_STACR	|
+	    EMAC_FTR_STACR_OC_INVERT	|
+#endif
+#ifdef CONFIG_IBM_NEW_EMAC_TAH
+	    EMAC_FTR_HAS_TAH	|
+#endif
+#ifdef CONFIG_IBM_NEW_EMAC_ZMII
+	    EMAC_FTR_HAS_ZMII	|
+#endif
+#ifdef CONFIG_IBM_NEW_EMAC_RGMII
+	    EMAC_FTR_HAS_RGMII	|
+#endif
+	    0,
+};
+
+static inline int emac_has_feature(struct emac_instance *dev,
+				   unsigned long feature)
+{
+	return (EMAC_FTRS_ALWAYS & feature) ||
+	       (EMAC_FTRS_POSSIBLE & dev->features & feature);
+}
+
+
+/* Ethtool get_regs complex data.
+ * We want to get not just EMAC registers, but also MAL, ZMII, RGMII, TAH
+ * when available.
+ *
+ * Returned BLOB consists of the ibm_emac_ethtool_regs_hdr,
+ * MAL registers, EMAC registers and optional ZMII, RGMII, TAH registers.
+ * Each register component is preceded with emac_ethtool_regs_subhdr.
+ * Order of the optional headers follows their relative bit posititions
+ * in emac_ethtool_regs_hdr.components
+ */
+#define EMAC_ETHTOOL_REGS_ZMII		0x00000001
+#define EMAC_ETHTOOL_REGS_RGMII		0x00000002
+#define EMAC_ETHTOOL_REGS_TAH		0x00000004
+
+struct emac_ethtool_regs_hdr {
+	u32 components;
+};
+
+struct emac_ethtool_regs_subhdr {
+	u32 version;
+	u32 index;
+};
+
+#endif /* __IBM_NEWEMAC_CORE_H */

drivers/net/ibm_newemac/debug.c

+/*
+ * drivers/net/ibm_newemac/debug.c
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/sysrq.h>
+#include <asm/io.h>
+
+#include "core.h"
+
+static spinlock_t emac_dbg_lock = SPIN_LOCK_UNLOCKED;
+
+static void emac_desc_dump(struct emac_instance *p)
+{
+	int i;
+	printk("** EMAC %s TX BDs **\n"
+	       " tx_cnt = %d tx_slot = %d ack_slot = %d\n",
+	       p->ofdev->node->full_name,
+	       p->tx_cnt, p->tx_slot, p->ack_slot);
+	for (i = 0; i < NUM_TX_BUFF / 2; ++i)
+		printk
+		    ("bd[%2d] 0x%08x %c 0x%04x %4u - bd[%2d] 0x%08x %c 0x%04x %4u\n",
+		     i, p->tx_desc[i].data_ptr, p->tx_skb[i] ? 'V' : ' ',
+		     p->tx_desc[i].ctrl, p->tx_desc[i].data_len,
+		     NUM_TX_BUFF / 2 + i,
+		     p->tx_desc[NUM_TX_BUFF / 2 + i].data_ptr,
+		     p->tx_skb[NUM_TX_BUFF / 2 + i] ? 'V' : ' ',
+		     p->tx_desc[NUM_TX_BUFF / 2 + i].ctrl,
+		     p->tx_desc[NUM_TX_BUFF / 2 + i].data_len);
+
+	printk("** EMAC %s RX BDs **\n"
+	       " rx_slot = %d flags = 0x%lx rx_skb_size = %d rx_sync_size = %d\n"
+	       " rx_sg_skb = 0x%p\n",
+	       p->ofdev->node->full_name,
+	       p->rx_slot, p->commac.flags, p->rx_skb_size,
+	       p->rx_sync_size, p->rx_sg_skb);
+	for (i = 0; i < NUM_RX_BUFF / 2; ++i)
+		printk
+		    ("bd[%2d] 0x%08x %c 0x%04x %4u - bd[%2d] 0x%08x %c 0x%04x %4u\n",
+		     i, p->rx_desc[i].data_ptr, p->rx_skb[i] ? 'V' : ' ',
+		     p->rx_desc[i].ctrl, p->rx_desc[i].data_len,
+		     NUM_RX_BUFF / 2 + i,
+		     p->rx_desc[NUM_RX_BUFF / 2 + i].data_ptr,
+		     p->rx_skb[NUM_RX_BUFF / 2 + i] ? 'V' : ' ',
+		     p->rx_desc[NUM_RX_BUFF / 2 + i].ctrl,
+		     p->rx_desc[NUM_RX_BUFF / 2 + i].data_len);
+}
+
+static void emac_mac_dump(struct emac_instance *dev)
+{
+	struct emac_regs __iomem *p = dev->emacp;
+
+	printk("** EMAC %s registers **\n"
+	       "MR0 = 0x%08x MR1 = 0x%08x TMR0 = 0x%08x TMR1 = 0x%08x\n"
+	       "RMR = 0x%08x ISR = 0x%08x ISER = 0x%08x\n"
+	       "IAR = %04x%08x VTPID = 0x%04x VTCI = 0x%04x\n"
+	       "IAHT: 0x%04x 0x%04x 0x%04x 0x%04x "
+	       "GAHT: 0x%04x 0x%04x 0x%04x 0x%04x\n"
+	       "LSA = %04x%08x IPGVR = 0x%04x\n"
+	       "STACR = 0x%08x TRTR = 0x%08x RWMR = 0x%08x\n"
+	       "OCTX = 0x%08x OCRX = 0x%08x IPCR = 0x%08x\n",
+	       dev->ofdev->node->full_name, in_be32(&p->mr0), in_be32(&p->mr1),
+	       in_be32(&p->tmr0), in_be32(&p->tmr1),
+	       in_be32(&p->rmr), in_be32(&p->isr), in_be32(&p->iser),
+	       in_be32(&p->iahr), in_be32(&p->ialr), in_be32(&p->vtpid),
+	       in_be32(&p->vtci),
+	       in_be32(&p->iaht1), in_be32(&p->iaht2), in_be32(&p->iaht3),
+	       in_be32(&p->iaht4),
+	       in_be32(&p->gaht1), in_be32(&p->gaht2), in_be32(&p->gaht3),
+	       in_be32(&p->gaht4),
+	       in_be32(&p->lsah), in_be32(&p->lsal), in_be32(&p->ipgvr),
+	       in_be32(&p->stacr), in_be32(&p->trtr), in_be32(&p->rwmr),
+	       in_be32(&p->octx), in_be32(&p->ocrx), in_be32(&p->ipcr)
+	    );
+
+	emac_desc_dump(dev);
+}
+
+static void emac_mal_dump(struct mal_instance *mal)
+{
+	int i;
+
+	printk("** MAL %s Registers **\n"
+	       "CFG = 0x%08x ESR = 0x%08x IER = 0x%08x\n"
+	       "TX|CASR = 0x%08x CARR = 0x%08x EOBISR = 0x%08x DEIR = 0x%08x\n"
+	       "RX|CASR = 0x%08x CARR = 0x%08x EOBISR = 0x%08x DEIR = 0x%08x\n",
+	       mal->ofdev->node->full_name,
+	       get_mal_dcrn(mal, MAL_CFG), get_mal_dcrn(mal, MAL_ESR),
+	       get_mal_dcrn(mal, MAL_IER),
+	       get_mal_dcrn(mal, MAL_TXCASR), get_mal_dcrn(mal, MAL_TXCARR),
+	       get_mal_dcrn(mal, MAL_TXEOBISR), get_mal_dcrn(mal, MAL_TXDEIR),
+	       get_mal_dcrn(mal, MAL_RXCASR), get_mal_dcrn(mal, MAL_RXCARR),
+	       get_mal_dcrn(mal, MAL_RXEOBISR), get_mal_dcrn(mal, MAL_RXDEIR)
+	    );
+
+	printk("TX|");
+	for (i = 0; i < mal->num_tx_chans; ++i) {
+		if (i && !(i % 4))
+			printk("\n   ");
+		printk("CTP%d = 0x%08x ", i, get_mal_dcrn(mal, MAL_TXCTPR(i)));
+	}
+	printk("\nRX|");
+	for (i = 0; i < mal->num_rx_chans; ++i) {
+		if (i && !(i % 4))
+			printk("\n   ");
+		printk("CTP%d = 0x%08x ", i, get_mal_dcrn(mal, MAL_RXCTPR(i)));
+	}
+	printk("\n   ");
+	for (i = 0; i < mal->num_rx_chans; ++i) {
+		u32 r = get_mal_dcrn(mal, MAL_RCBS(i));
+		if (i && !(i % 3))
+			printk("\n   ");
+		printk("RCBS%d = 0x%08x (%d) ", i, r, r * 16);
+	}
+	printk("\n");
+}
+
+static struct emac_instance *__emacs[4];
+static struct mal_instance *__mals[1];
+
+void emac_dbg_register(struct emac_instance *dev)
+{
+	unsigned long flags;
+	int i;
+
+	spin_lock_irqsave(&emac_dbg_lock, flags);
+	for (i = 0; i < ARRAY_SIZE(__emacs); i++)
+		if (__emacs[i] == NULL) {
+			__emacs[i] = dev;
+			break;
+		}
+	spin_unlock_irqrestore(&emac_dbg_lock, flags);
+}
+
+void emac_dbg_unregister(struct emac_instance *dev)
+{
+	unsigned long flags;
+	int i;
+
+	spin_lock_irqsave(&emac_dbg_lock, flags);
+	for (i = 0; i < ARRAY_SIZE(__emacs); i++)
+		if (__emacs[i] == dev) {
+			__emacs[i] = NULL;
+			break;
+		}
+	spin_unlock_irqrestore(&emac_dbg_lock, flags);
+}
+
+void mal_dbg_register(struct mal_instance *mal)
+{
+	unsigned long flags;
+	int i;
+
+	spin_lock_irqsave(&emac_dbg_lock, flags);
+	for (i = 0; i < ARRAY_SIZE(__mals); i++)
+		if (__mals[i] == NULL) {
+			__mals[i] = mal;
+			break;
+		}
+	spin_unlock_irqrestore(&emac_dbg_lock, flags);
+}
+
+void mal_dbg_unregister(struct mal_instance *mal)
+{
+	unsigned long flags;
+	int i;
+
+	spin_lock_irqsave(&emac_dbg_lock, flags);
+	for (i = 0; i < ARRAY_SIZE(__mals); i++)
+		if (__mals[i] == mal) {
+			__mals[i] = NULL;
+			break;
+		}
+	spin_unlock_irqrestore(&emac_dbg_lock, flags);
+}
+
+void emac_dbg_dump_all(void)
+{
+	unsigned int i;
+	unsigned long flags;
+
+	spin_lock_irqsave(&emac_dbg_lock, flags);
+
+	for (i = 0; i < ARRAY_SIZE(__mals); ++i)
+		if (__mals[i])
+			emac_mal_dump(__mals[i]);
+
+	for (i = 0; i < ARRAY_SIZE(__emacs); ++i)
+		if (__emacs[i])
+			emac_mac_dump(__emacs[i]);
+
+	spin_unlock_irqrestore(&emac_dbg_lock, flags);
+}
+
+#if defined(CONFIG_MAGIC_SYSRQ)
+static void emac_sysrq_handler(int key, struct tty_struct *tty)
+{
+	emac_dbg_dump_all();
+}
+
+static struct sysrq_key_op emac_sysrq_op = {
+	.handler = emac_sysrq_handler,
+	.help_msg = "emaC",
+	.action_msg = "Show EMAC(s) status",
+};
+
+int __init emac_init_debug(void)
+{
+	return register_sysrq_key('c', &emac_sysrq_op);
+}
+
+void __exit emac_fini_debug(void)
+{
+	unregister_sysrq_key('c', &emac_sysrq_op);
+}
+
+#else
+int __init emac_init_debug(void)
+{
+	return 0;
+}
+void __exit emac_fini_debug(void)
+{
+}
+#endif				/* CONFIG_MAGIC_SYSRQ */

drivers/net/ibm_newemac/debug.h

+/*
+ * drivers/net/ibm_newemac/debug.h
+ *
+ * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines.
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __IBM_NEWEMAC_DEBUG_H
+#define __IBM_NEWEMAC_DEBUG_H
+
+#include <linux/init.h>
+
+#include "core.h"
+
+#if defined(CONFIG_IBM_NEW_EMAC_DEBUG)
+
+struct emac_instance;
+struct mal_instance;
+
+extern void emac_dbg_register(struct emac_instance *dev);
+extern void emac_dbg_unregister(struct emac_instance *dev);
+extern void mal_dbg_register(struct mal_instance *mal);
+extern void mal_dbg_unregister(struct mal_instance *mal);
+extern int emac_init_debug(void) __init;
+extern void emac_fini_debug(void) __exit;
+extern void emac_dbg_dump_all(void);
+
+# define DBG_LEVEL		1
+
+#else
+
+# define emac_dbg_register(x)	do { } while(0)
+# define emac_dbg_unregister(x)	do { } while(0)
+# define mal_dbg_register(x)	do { } while(0)
+# define mal_dbg_unregister(x)	do { } while(0)
+# define emac_init_debug()	do { } while(0)
+# define emac_fini_debug()	do { } while(0)
+# define emac_dbg_dump_all()	do { } while(0)
+
+# define DBG_LEVEL		0
+
+#endif
+
+#define EMAC_DBG(dev, name, fmt, arg...) \
+	printk(KERN_DEBUG #name "%s: " fmt, dev->ofdev->node->full_name, ## arg)
+
+#if DBG_LEVEL > 0
+#  define DBG(d,f,x...)		EMAC_DBG(d, emac, f, ##x)
+#  define MAL_DBG(d,f,x...)	EMAC_DBG(d, mal, f, ##x)
+#  define ZMII_DBG(d,f,x...)	EMAC_DBG(d, zmii, f, ##x)
+#  define RGMII_DBG(d,f,x...)	EMAC_DBG(d, rgmii, f, ##x)
+#  define NL			"\n"
+#else
+#  define DBG(f,x...)		((void)0)
+#  define MAL_DBG(d,f,x...)	((void)0)
+#  define ZMII_DBG(d,f,x...)	((void)0)
+#  define RGMII_DBG(d,f,x...)	((void)0)
+#endif
+#if DBG_LEVEL > 1
+#  define DBG2(d,f,x...) 	DBG(d,f, ##x)
+#  define MAL_DBG2(d,f,x...) 	MAL_DBG(d,f, ##x)
+#  define ZMII_DBG2(d,f,x...) 	ZMII_DBG(d,f, ##x)
+#  define RGMII_DBG2(d,f,x...) 	RGMII_DBG(d,f, ##x)
+#else
+#  define DBG2(f,x...) 		((void)0)
+#  define MAL_DBG2(d,f,x...) 	((void)0)
+#  define ZMII_DBG2(d,f,x...) 	((void)0)
+#  define RGMII_DBG2(d,f,x...) 	((void)0)
+#endif
+
+#endif /* __IBM_NEWEMAC_DEBUG_H */

drivers/net/ibm_newemac/emac.h

+/*
+ * drivers/net/ibm_newemac/emac.h
+ *
+ * Register definitions for PowerPC 4xx on-chip ethernet contoller
+ *
+ * Copyright (c) 2004, 2005 Zultys Technologies.
+ * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *
+ * Based on original work by
+ *      Matt Porter <mporter@kernel.crashing.org>
+ *      Armin Kuster <akuster@mvista.com>
+ * 	Copyright 2002-2004 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+#ifndef __IBM_NEWEMAC_H
+#define __IBM_NEWEMAC_H
+
+#include <linux/types.h>
+
+/* EMAC registers 		Write Access rules */
+struct emac_regs {
+	u32 mr0;		/* special 	*/
+	u32 mr1;		/* Reset 	*/
+	u32 tmr0;		/* special 	*/
+	u32 tmr1;		/* special 	*/
+	u32 rmr;		/* Reset 	*/
+	u32 isr;		/* Always 	*/
+	u32 iser;		/* Reset 	*/
+	u32 iahr;		/* Reset, R, T 	*/
+	u32 ialr;		/* Reset, R, T 	*/
+	u32 vtpid;		/* Reset, R, T 	*/
+	u32 vtci;		/* Reset, R, T 	*/
+	u32 ptr;		/* Reset,    T 	*/
+	u32 iaht1;		/* Reset, R	*/
+	u32 iaht2;		/* Reset, R	*/
+	u32 iaht3;		/* Reset, R	*/
+	u32 iaht4;		/* Reset, R	*/
+	u32 gaht1;		/* Reset, R	*/
+	u32 gaht2;		/* Reset, R	*/
+	u32 gaht3;		/* Reset, R	*/
+	u32 gaht4;		/* Reset, R	*/
+	u32 lsah;
+	u32 lsal;
+	u32 ipgvr;		/* Reset,    T 	*/
+	u32 stacr;		/* special 	*/
+	u32 trtr;		/* special 	*/
+	u32 rwmr;		/* Reset 	*/
+	u32 octx;
+	u32 ocrx;
+	u32 ipcr;
+};
+
+/*
+ * PHY mode settings (EMAC <-> ZMII/RGMII bridge <-> PHY)
+ */
+#define PHY_MODE_NA	0
+#define PHY_MODE_MII	1
+#define PHY_MODE_RMII	2
+#define PHY_MODE_SMII	3
+#define PHY_MODE_RGMII	4
+#define PHY_MODE_TBI	5
+#define PHY_MODE_GMII	6
+#define PHY_MODE_RTBI	7
+#define PHY_MODE_SGMII	8
+
+
+#define EMAC_ETHTOOL_REGS_VER		0
+#define EMAC_ETHTOOL_REGS_SIZE		(sizeof(struct emac_regs) - sizeof(u32))
+#define EMAC4_ETHTOOL_REGS_VER      	1
+#define EMAC4_ETHTOOL_REGS_SIZE		sizeof(struct emac_regs)
+
+/* EMACx_MR0 */
+#define EMAC_MR0_RXI			0x80000000
+#define EMAC_MR0_TXI			0x40000000
+#define EMAC_MR0_SRST			0x20000000
+#define EMAC_MR0_TXE			0x10000000
+#define EMAC_MR0_RXE			0x08000000
+#define EMAC_MR0_WKE			0x04000000
+
+/* EMACx_MR1 */
+#define EMAC_MR1_FDE			0x80000000
+#define EMAC_MR1_ILE			0x40000000
+#define EMAC_MR1_VLE			0x20000000
+#define EMAC_MR1_EIFC			0x10000000
+#define EMAC_MR1_APP			0x08000000
+#define EMAC_MR1_IST			0x01000000
+
+#define EMAC_MR1_MF_MASK		0x00c00000
+#define EMAC_MR1_MF_10			0x00000000
+#define EMAC_MR1_MF_100			0x00400000
+#define EMAC_MR1_MF_1000		0x00800000
+#define EMAC_MR1_MF_1000GPCS		0x00c00000
+#define EMAC_MR1_MF_IPPA(id)		(((id) & 0x1f) << 6)
+
+#define EMAC_MR1_RFS_4K			0x00300000
+#define EMAC_MR1_RFS_16K		0x00000000
+#define EMAC_MR1_TFS_2K			0x00080000
+#define EMAC_MR1_TR0_MULT		0x00008000
+#define EMAC_MR1_JPSM			0x00000000
+#define EMAC_MR1_MWSW_001		0x00000000
+#define EMAC_MR1_BASE(opb)		(EMAC_MR1_TFS_2K | EMAC_MR1_TR0_MULT)
+
+
+#define EMAC4_MR1_RFS_2K		0x00100000
+#define EMAC4_MR1_RFS_4K		0x00180000
+#define EMAC4_MR1_RFS_16K		0x00280000
+#define EMAC4_MR1_TFS_2K       		0x00020000
+#define EMAC4_MR1_TFS_4K		0x00030000
+#define EMAC4_MR1_TR			0x00008000
+#define EMAC4_MR1_MWSW_001		0x00001000
+#define EMAC4_MR1_JPSM			0x00000800
+#define EMAC4_MR1_OBCI_MASK		0x00000038
+#define EMAC4_MR1_OBCI_50		0x00000000
+#define EMAC4_MR1_OBCI_66		0x00000008
+#define EMAC4_MR1_OBCI_83		0x00000010
+#define EMAC4_MR1_OBCI_100		0x00000018
+#define EMAC4_MR1_OBCI_100P		0x00000020
+#define EMAC4_MR1_OBCI(freq)		((freq) <= 50  ? EMAC4_MR1_OBCI_50 : \
+					 (freq) <= 66  ? EMAC4_MR1_OBCI_66 : \
+					 (freq) <= 83  ? EMAC4_MR1_OBCI_83 : \
+					 (freq) <= 100 ? EMAC4_MR1_OBCI_100 : \
+						EMAC4_MR1_OBCI_100P)
+
+/* EMACx_TMR0 */
+#define EMAC_TMR0_GNP			0x80000000
+#define EMAC_TMR0_DEFAULT		0x00000000
+#define EMAC4_TMR0_TFAE_2_32		0x00000001
+#define EMAC4_TMR0_TFAE_4_64		0x00000002
+#define EMAC4_TMR0_TFAE_8_128		0x00000003
+#define EMAC4_TMR0_TFAE_16_256		0x00000004
+#define EMAC4_TMR0_TFAE_32_512		0x00000005
+#define EMAC4_TMR0_TFAE_64_1024		0x00000006
+#define EMAC4_TMR0_TFAE_128_2048	0x00000007
+#define EMAC4_TMR0_DEFAULT		EMAC4_TMR0_TFAE_2_32
+#define EMAC_TMR0_XMIT			(EMAC_TMR0_GNP | EMAC_TMR0_DEFAULT)
+#define EMAC4_TMR0_XMIT			(EMAC_TMR0_GNP | EMAC4_TMR0_DEFAULT)
+
+/* EMACx_TMR1 */
+
+#define EMAC_TMR1(l,h)			(((l) << 27) | (((h) & 0xff) << 16))
+#define EMAC4_TMR1(l,h)			(((l) << 27) | (((h) & 0x3ff) << 14))
+
+/* EMACx_RMR */
+#define EMAC_RMR_SP			0x80000000
+#define EMAC_RMR_SFCS			0x40000000
+#define EMAC_RMR_RRP			0x20000000
+#define EMAC_RMR_RFP			0x10000000
+#define EMAC_RMR_ROP			0x08000000
+#define EMAC_RMR_RPIR			0x04000000
+#define EMAC_RMR_PPP			0x02000000
+#define EMAC_RMR_PME			0x01000000
+#define EMAC_RMR_PMME			0x00800000
+#define EMAC_RMR_IAE			0x00400000
+#define EMAC_RMR_MIAE			0x00200000
+#define EMAC_RMR_BAE			0x00100000
+#define EMAC_RMR_MAE			0x00080000
+#define EMAC_RMR_BASE			0x00000000
+#define EMAC4_RMR_RFAF_2_32		0x00000001
+#define EMAC4_RMR_RFAF_4_64		0x00000002
+#define EMAC4_RMR_RFAF_8_128		0x00000003
+#define EMAC4_RMR_RFAF_16_256		0x00000004
+#define EMAC4_RMR_RFAF_32_512		0x00000005
+#define EMAC4_RMR_RFAF_64_1024		0x00000006
+#define EMAC4_RMR_RFAF_128_2048		0x00000007
+#define EMAC4_RMR_BASE			EMAC4_RMR_RFAF_128_2048
+
+/* EMACx_ISR & EMACx_ISER */
+#define EMAC4_ISR_TXPE			0x20000000
+#define EMAC4_ISR_RXPE			0x10000000
+#define EMAC4_ISR_TXUE			0x08000000
+#define EMAC4_ISR_RXOE			0x04000000
+#define EMAC_ISR_OVR			0x02000000
+#define EMAC_ISR_PP			0x01000000
+#define EMAC_ISR_BP			0x00800000
+#define EMAC_ISR_RP			0x00400000
+#define EMAC_ISR_SE			0x00200000
+#define EMAC_ISR_ALE			0x00100000
+#define EMAC_ISR_BFCS			0x00080000
+#define EMAC_ISR_PTLE			0x00040000
+#define EMAC_ISR_ORE			0x00020000
+#define EMAC_ISR_IRE			0x00010000
+#define EMAC_ISR_SQE			0x00000080
+#define EMAC_ISR_TE			0x00000040
+#define EMAC_ISR_MOS			0x00000002
+#define EMAC_ISR_MOF			0x00000001
+
+/* EMACx_STACR */
+#define EMAC_STACR_PHYD_MASK		0xffff
+#define EMAC_STACR_PHYD_SHIFT		16
+#define EMAC_STACR_OC			0x00008000
+#define EMAC_STACR_PHYE			0x00004000
+#define EMAC_STACR_STAC_MASK		0x00003000
+#define EMAC_STACR_STAC_READ		0x00001000
+#define EMAC_STACR_STAC_WRITE		0x00002000
+#define EMAC_STACR_OPBC_MASK		0x00000C00
+#define EMAC_STACR_OPBC_50		0x00000000
+#define EMAC_STACR_OPBC_66		0x00000400
+#define EMAC_STACR_OPBC_83		0x00000800
+#define EMAC_STACR_OPBC_100		0x00000C00
+#define EMAC_STACR_OPBC(freq)		((freq) <= 50 ? EMAC_STACR_OPBC_50 : \
+					 (freq) <= 66 ? EMAC_STACR_OPBC_66 : \
+					 (freq) <= 83 ? EMAC_STACR_OPBC_83 : EMAC_STACR_OPBC_100)
+#define EMAC_STACR_BASE(opb)		EMAC_STACR_OPBC(opb)
+#define EMAC4_STACR_BASE(opb)		0x00000000
+#define EMAC_STACR_PCDA_MASK		0x1f
+#define EMAC_STACR_PCDA_SHIFT		5
+#define EMAC_STACR_PRA_MASK		0x1f
+#define EMACX_STACR_STAC_MASK		0x00003800
+#define EMACX_STACR_STAC_READ		0x00001000
+#define EMACX_STACR_STAC_WRITE		0x00000800
+#define EMACX_STACR_STAC_IND_ADDR	0x00002000
+#define EMACX_STACR_STAC_IND_READ	0x00003800
+#define EMACX_STACR_STAC_IND_READINC	0x00003000
+#define EMACX_STACR_STAC_IND_WRITE	0x00002800
+
+
+/* EMACx_TRTR */
+#define EMAC_TRTR_SHIFT_EMAC4		27
+#define EMAC_TRTR_SHIFT			24
+
+/* EMAC specific TX descriptor control fields (write access) */
+#define EMAC_TX_CTRL_GFCS		0x0200
+#define EMAC_TX_CTRL_GP			0x0100
+#define EMAC_TX_CTRL_ISA		0x0080
+#define EMAC_TX_CTRL_RSA		0x0040
+#define EMAC_TX_CTRL_IVT		0x0020
+#define EMAC_TX_CTRL_RVT		0x0010
+#define EMAC_TX_CTRL_TAH_CSUM		0x000e
+
+/* EMAC specific TX descriptor status fields (read access) */
+#define EMAC_TX_ST_BFCS			0x0200
+#define EMAC_TX_ST_LCS			0x0080
+#define EMAC_TX_ST_ED			0x0040
+#define EMAC_TX_ST_EC			0x0020
+#define EMAC_TX_ST_LC			0x0010
+#define EMAC_TX_ST_MC			0x0008
+#define EMAC_TX_ST_SC			0x0004
+#define EMAC_TX_ST_UR			0x0002
+#define EMAC_TX_ST_SQE			0x0001
+#define EMAC_IS_BAD_TX			(EMAC_TX_ST_LCS | EMAC_TX_ST_ED | \
+					 EMAC_TX_ST_EC | EMAC_TX_ST_LC | \
+					 EMAC_TX_ST_MC | EMAC_TX_ST_UR)
+#define EMAC_IS_BAD_TX_TAH		(EMAC_TX_ST_LCS | EMAC_TX_ST_ED | \
+					 EMAC_TX_ST_EC | EMAC_TX_ST_LC)
+
+/* EMAC specific RX descriptor status fields (read access) */
+#define EMAC_RX_ST_OE			0x0200
+#define EMAC_RX_ST_PP			0x0100
+#define EMAC_RX_ST_BP			0x0080
+#define EMAC_RX_ST_RP			0x0040
+#define EMAC_RX_ST_SE			0x0020
+#define EMAC_RX_ST_AE			0x0010
+#define EMAC_RX_ST_BFCS			0x0008
+#define EMAC_RX_ST_PTL			0x0004
+#define EMAC_RX_ST_ORE			0x0002
+#define EMAC_RX_ST_IRE			0x0001
+#define EMAC_RX_TAH_BAD_CSUM		0x0003
+#define EMAC_BAD_RX_MASK		(EMAC_RX_ST_OE | EMAC_RX_ST_BP | \
+					 EMAC_RX_ST_RP | EMAC_RX_ST_SE | \
+					 EMAC_RX_ST_AE | EMAC_RX_ST_BFCS | \
+					 EMAC_RX_ST_PTL | EMAC_RX_ST_ORE | \
+					 EMAC_RX_ST_IRE )
+#endif /* __IBM_NEWEMAC_H */