Merge tag 'phy-for-4.13' of...

Merge tag 'phy-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.13

 *) Group phy drivers into vendor specific directories
 *) Add USB3 PHY driver for Renesas R-Car Gen3
 *) Add USB2 PHY driver for Meson GXL and GXM SoCs
 *) Add USB DRD PHY driver for Broadcom Northstar2
 *) Add USB PHY driver for CPCAP PMIC USB
 *) Make phy-meson8b-usb2 driver support USB PHY on Meson8
 *) Make phy-tusb1210 driver support TUSB1211
 *) Make phy-rockchip-inno-usb2 driver support usb2-phy in rk3228 SoCs
 *) Make phy-brcm-sata driver support for stingray SATA phy
 *) Make bcm-ns-usb3 as a MDIO driver
 *) Make rockchip-inno-usb2 support two host ports
 *) Implement ->set_mode() callback in phy-tusb1210
 *) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt

@@ -3,9 +3,10 @@ Driver for Broadcom Northstar USB 3.0 PHY
 Required properties:
 
 - compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy".
-- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B
-       MMI.
-- reg-names: "dmp" and "ccb-mii"
+- reg: address of MDIO bus device
+- usb3-dmp-syscon: phandle to syscon with DMP (Device Management Plugin)
+		   registers
+- #phy-cells: must be 0
 
 Initialization of USB 3.0 PHY depends on Northstar version. There are currently
 three known series: Ax, Bx and Cx.
@@ -15,9 +16,19 @@ Known B1: BCM4707 rev 6
 Known C0: BCM47094 rev 0
 
 Example:
-	usb3-phy {
-		compatible = "brcm,ns-ax-usb3-phy";
-		reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
-		reg-names = "dmp", "ccb-mii";
-		#phy-cells = <0>;
+	mdio: mdio@0 {
+		reg = <0x0>;
+		#size-cells = <1>;
+		#address-cells = <0>;
+
+		usb3-phy@10 {
+			compatible = "brcm,ns-ax-usb3-phy";
+			reg = <0x10>;
+			usb3-dmp-syscon = <&usb3_dmp>;
+			#phy-cells = <0>;
+		};
+	};
+
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
 	};

Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt

+BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
+
+Required properties:
+ - compatible: brcm,ns2-drd-phy
+ - reg: offset and length of the NS2 PHY related registers.
+ - reg-names
+   The below registers must be provided.
+   icfg - for DRD ICFG configurations
+   rst-ctrl - for DRD IDM reset
+   crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
+   usb2-strap - for port over current polarity reversal
+ - #phy-cells: Must be 0. No args required.
+ - vbus-gpios: vbus gpio binding
+ - id-gpios: id gpio binding
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+	usbdrd_phy: phy@66000960 {
+			#phy-cells = <0>;
+			compatible = "brcm,ns2-drd-phy";
+			reg = <0x66000960 0x24>,
+			      <0x67012800 0x4>,
+			      <0x6501d148 0x4>,
+			      <0x664d0700 0x4>;
+			reg-names = "icfg", "rst-ctrl",
+				    "crmu-ctrl", "usb2-strap";
+			id-gpios = <&gpio_g 30 0>;
+			vbus-gpios = <&gpio_g 31 0>;
+	};

Documentation/devicetree/bindings/phy/brcm-sata-phy.txt

@@ -7,12 +7,13 @@ Required properties:
      "brcm,iproc-ns2-sata-phy"
      "brcm,iproc-nsp-sata-phy"
      "brcm,phy-sata3"
+     "brcm,iproc-sr-sata-phy"
 - address-cells: should be 1
 - size-cells: should be 0
 - reg: register ranges for the PHY PCB interface
 - reg-names: should be "phy" and "phy-ctrl"
      The "phy-ctrl" registers are only required for
-     "brcm,iproc-ns2-sata-phy".
+     "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy".
 
 Sub-nodes:
   Each port's PHY should be represented as a sub-node.
@@ -23,8 +24,8 @@ Sub-nodes required properties:
 
 Sub-nodes optional properties:
 - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
-     This property is not applicable for "brcm,iproc-ns2-sata-phy" and
-     "brcm,iproc-nsp-sata-phy".
+     This property is not applicable for "brcm,iproc-ns2-sata-phy",
+     "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy".
 
 Example:
 	sata-phy@f0458100 {

Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt

+* Amlogic Meson GXL and GXM USB2 PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-gxl-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+
+Optional properties:
+- phy-supply:	see phy-bindings.txt in this directory
+
+
+Example:
+	usb2_phy0: phy@78000 {
+		compatible = "amlogic,meson-gxl-usb2-phy";
+		#phy-cells = <0>;
+		reg = <0x0 0x78000 0x0 0x20>;
+	};

Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt

-* Amlogic Meson8b and GXBB USB2 PHY
+* Amlogic Meson8, Meson8b and GXBB USB2 PHY
 
 Required properties:
 - compatible:	Depending on the platform this should be one of:
+	"amlogic,meson8-usb2-phy"
 	"amlogic,meson8b-usb2-phy"
 	"amlogic,meson-gxbb-usb2-phy"
 - reg:		The base address and length of the registers

Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt

+Motorola CPCAP PMIC USB PHY binding
+
+Required properties:
+compatible: Shall be either "motorola,cpcap-usb-phy" or
+	    "motorola,mapphone-cpcap-usb-phy"
+#phy-cells: Shall be 0
+interrupts: CPCAP PMIC interrupts used by the USB PHY
+interrupt-names: Interrupt names
+io-channels: IIO ADC channels used by the USB PHY
+io-channel-names: IIO ADC channel names
+vusb-supply: Regulator for the PHY
+
+Optional properties:
+pinctrl: Optional alternate pin modes for the PHY
+pinctrl-names: Names for optional pin modes
+mode-gpios: Optional GPIOs for configuring alternate modes
+
+Example:
+cpcap_usb2_phy: phy {
+	compatible = "motorola,mapphone-cpcap-usb-phy";
+	pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>;
+	pinctrl-1 = <&usb_ulpi_pins>;
+	pinctrl-2 = <&usb_utmi_pins>;
+	pinctrl-3 = <&uart3_pins>;
+	pinctrl-names = "default", "ulpi", "utmi", "uart";
+	#phy-cells = <0>;
+	interrupts-extended = <
+		&cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
+		&cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
+		&cpcap 48 1
+	>;
+	interrupt-names =
+		"id_ground", "id_float", "se0conn", "vbusvld",
+		"sessvld", "sessend", "se1", "dm", "dp";
+	mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH
+		      &gpio1 0 GPIO_ACTIVE_HIGH>;
+	io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>;
+	io-channel-names = "vbus", "id";
+	vusb-supply = <&vusb>;
+};

Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt

@@ -2,6 +2,7 @@ ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
 
 Required properties (phy (parent) node):
  - compatible : should be one of the listed compatibles:
+	* "rockchip,rk3228-usb2phy"
 	* "rockchip,rk3328-usb2phy"
 	* "rockchip,rk3366-usb2phy"
 	* "rockchip,rk3399-usb2phy"

Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt

+* Renesas R-Car generation 3 USB 3.0 PHY
+
+This file provides information on what the device node for the R-Car generation
+3 USB 3.0 PHY contains.
+If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL
+instead of USB3_CLK. However, if you don't want to these features, you don't
+need this driver.
+
+Required properties:
+- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795
+	      SoC.
+	      "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796
+	      SoC.
+	      "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible
+	      device.
+
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
+- reg: offset and length of the USB 3.0 PHY register block.
+- clocks: A list of phandles and clock-specifier pairs.
+- clock-names: Name of the clocks.
+  - The funcional clock must be "usb3-if".
+  - The usb3's external clock must be "usb3s_clk".
+  - The usb2's external clock must be "usb_extal". If you want to use the ssc,
+    the clock-frequency must not be 0.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
+
+Optional properties:
+- renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using
+		     the following values as u32:
+			- 0 (or the property doesn't exist): disable the ssc
+			- 4980: enable the ssc as -4980 ppm
+			- 4492: enable the ssc as -4492 ppm
+			- 4003: enable the ssc as -4003 ppm
+
+Example (R-Car H3):
+
+	usb-phy@e65ee000 {
+		compatible = "renesas,r8a7795-usb3-phy",
+			     "renesas,rcar-gen3-usb3-phy";
+		reg = <0 0xe65ee000 0 0x90>;
+		clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>;
+		clock-names = "usb3-if", "usb3s_clk", "usb_extal";
+	};

MAINTAINERS

@@ -1843,8 +1843,8 @@ F:	drivers/i2c/busses/i2c-st.c
 F:	drivers/media/rc/st_rc.c
 F:	drivers/media/platform/sti/c8sectpfe/
 F:	drivers/mmc/host/sdhci-st.c
-F:	drivers/phy/phy-miphy28lp.c
-F:	drivers/phy/phy-stih407-usb.c
+F:	drivers/phy/st/phy-miphy28lp.c
+F:	drivers/phy/st/phy-stih407-usb.c
 F:	drivers/pinctrl/pinctrl-st.c
 F:	drivers/remoteproc/st_remoteproc.c
 F:	drivers/remoteproc/st_slim_rproc.c
@@ -10831,11 +10831,11 @@ L:	linux-iio@vger.kernel.org
 S:	Supported
 F:	drivers/iio/adc/rcar_gyro_adc.c
 
-RENESAS USB2 PHY DRIVER
+RENESAS USB PHY DRIVER
 M:	Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
 L:	linux-renesas-soc@vger.kernel.org
 S:	Maintained
-F:	drivers/phy/phy-rcar-gen3-usb2.c
+F:	drivers/phy/renesas/phy-rcar-gen3-usb*.c
 
 RESET CONTROLLER FRAMEWORK
 M:	Philipp Zabel <p.zabel@pengutronix.de>
@@ -11237,12 +11237,12 @@ L:	linux-kernel@vger.kernel.org
 S:	Supported
 F:	Documentation/devicetree/bindings/phy/samsung-phy.txt
 F:	Documentation/phy/samsung-usb2.txt
-F:	drivers/phy/phy-exynos4210-usb2.c
-F:	drivers/phy/phy-exynos4x12-usb2.c
-F:	drivers/phy/phy-exynos5250-usb2.c
-F:	drivers/phy/phy-s5pv210-usb2.c
-F:	drivers/phy/phy-samsung-usb2.c
-F:	drivers/phy/phy-samsung-usb2.h
+F:	drivers/phy/samsung/phy-exynos4210-usb2.c
+F:	drivers/phy/samsung/phy-exynos4x12-usb2.c
+F:	drivers/phy/samsung/phy-exynos5250-usb2.c
+F:	drivers/phy/samsung/phy-s5pv210-usb2.c
+F:	drivers/phy/samsung/phy-samsung-usb2.c
+F:	drivers/phy/samsung/phy-samsung-usb2.h
 
 SERIAL DRIVERS
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/phy/Makefile

@@ -3,64 +3,21 @@
 #
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
-obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
-obj-$(CONFIG_PHY_BCM_NS_USB3)		+= phy-bcm-ns-usb3.o
-obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
-obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
-obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
-obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
-obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
-obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
-obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
-obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
 obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+= phy-lpc18xx-usb-otg.o
-obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
-obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
-obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
-obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
-obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
-obj-$(CONFIG_PHY_RCAR_GEN3_USB2)	+= phy-rcar-gen3-usb2.o
-obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
-obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
-obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
-obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
-obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
-obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
-obj-$(CONFIG_PHY_HI6220_USB)		+= phy-hi6220-usb.o
 obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
-obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
-obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
-obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
-phy-exynos-usb2-y			+= phy-samsung-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
-obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
-obj-$(CONFIG_PHY_EXYNOS_PCIE)	+= phy-exynos-pcie.o
-obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
-obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
-obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
-obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
-obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
-obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
-obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
-obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
-obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
-obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
-obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
-obj-$(CONFIG_PHY_QCOM_QMP)		+= phy-qcom-qmp.o
-obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
-obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
-obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
-obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
-obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
-obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
-obj-$(CONFIG_ARCH_TEGRA) += tegra/
-obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
-obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
+
+obj-$(CONFIG_ARCH_SUNXI)		+= allwinner/
+obj-$(CONFIG_ARCH_MESON)		+= amlogic/
+obj-$(CONFIG_ARCH_RENESAS)		+= renesas/
+obj-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip/
+obj-$(CONFIG_ARCH_TEGRA)		+= tegra/
+obj-y					+= broadcom/	\
+					   hisilicon/	\
+					   marvell/	\
+					   motorola/	\
+					   qualcomm/	\
+					   samsung/	\
+					   st/		\
+					   ti/

drivers/phy/allwinner/Kconfig

+#
+# Phy drivers for Allwinner platforms
+#
+config PHY_SUN4I_USB
+	tristate "Allwinner sunxi SoC USB PHY driver"
+	depends on ARCH_SUNXI && HAS_IOMEM && OF
+	depends on RESET_CONTROLLER
+	depends on EXTCON
+	depends on POWER_SUPPLY
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_COMMON
+	help
+	  Enable this to support the transceiver that is part of Allwinner
+	  sunxi SoCs.
+
+	  This driver controls the entire USB PHY block, both the USB OTG
+	  parts, as well as the 2 regular USB 2 host PHYs.
+
+config PHY_SUN9I_USB
+	tristate "Allwinner sun9i SoC USB PHY driver"
+	depends on ARCH_SUNXI && HAS_IOMEM && OF
+	depends on RESET_CONTROLLER
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the transceiver that is part of Allwinner
+	  sun9i SoCs.
+
+	  This driver controls each individual USB 2 host PHY.

drivers/phy/allwinner/Makefile

+obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
+obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o

drivers/phy/amlogic/Kconfig

+#
+# Phy drivers for Amlogic platforms
+#
+config PHY_MESON8B_USB2
+	tristate "Meson8, Meson8b and GXBB USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson8,
+	  Meson8b and GXBB SoCs.
+	  If unsure, say N.
+
+config PHY_MESON_GXL_USB2
+	tristate "Meson GXL and GXM USB2 PHY drivers"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson
+	  GXL and GXM SoCs.
+	  If unsure, say N.

drivers/phy/amlogic/Makefile

+obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
+obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o

drivers/phy/amlogic/phy-meson-gxl-usb2.c

+/*
+ * Meson GXL and GXM USB2 PHY driver
+ *
+ * Copyright (C) 2017 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/usb/of.h>
+
+/* bits [31:27] are read-only */
+#define U2P_R0							0x0
+	#define U2P_R0_BYPASS_SEL				BIT(0)
+	#define U2P_R0_BYPASS_DM_EN				BIT(1)
+	#define U2P_R0_BYPASS_DP_EN				BIT(2)
+	#define U2P_R0_TXBITSTUFF_ENH				BIT(3)
+	#define U2P_R0_TXBITSTUFF_EN				BIT(4)
+	#define U2P_R0_DM_PULLDOWN				BIT(5)
+	#define U2P_R0_DP_PULLDOWN				BIT(6)
+	#define U2P_R0_DP_VBUS_VLD_EXT_SEL			BIT(7)
+	#define U2P_R0_DP_VBUS_VLD_EXT				BIT(8)
+	#define U2P_R0_ADP_PRB_EN				BIT(9)
+	#define U2P_R0_ADP_DISCHARGE				BIT(10)
+	#define U2P_R0_ADP_CHARGE				BIT(11)
+	#define U2P_R0_DRV_VBUS					BIT(12)
+	#define U2P_R0_ID_PULLUP				BIT(13)
+	#define U2P_R0_LOOPBACK_EN_B				BIT(14)
+	#define U2P_R0_OTG_DISABLE				BIT(15)
+	#define U2P_R0_COMMON_ONN				BIT(16)
+	#define U2P_R0_FSEL_MASK				GENMASK(19, 17)
+	#define U2P_R0_REF_CLK_SEL_MASK				GENMASK(21, 20)
+	#define U2P_R0_POWER_ON_RESET				BIT(22)
+	#define U2P_R0_V_ATE_TEST_EN_B_MASK			GENMASK(24, 23)
+	#define U2P_R0_ID_SET_ID_DQ				BIT(25)
+	#define U2P_R0_ATE_RESET				BIT(26)
+	#define U2P_R0_FSV_MINUS				BIT(27)
+	#define U2P_R0_FSV_PLUS					BIT(28)
+	#define U2P_R0_BYPASS_DM_DATA				BIT(29)
+	#define U2P_R0_BYPASS_DP_DATA				BIT(30)
+
+#define U2P_R1							0x4
+	#define U2P_R1_BURN_IN_TEST				BIT(0)
+	#define U2P_R1_ACA_ENABLE				BIT(1)
+	#define U2P_R1_DCD_ENABLE				BIT(2)
+	#define U2P_R1_VDAT_SRC_EN_B				BIT(3)
+	#define U2P_R1_VDAT_DET_EN_B				BIT(4)
+	#define U2P_R1_CHARGES_SEL				BIT(5)
+	#define U2P_R1_TX_PREEMP_PULSE_TUNE			BIT(6)
+	#define U2P_R1_TX_PREEMP_AMP_TUNE_MASK			GENMASK(8, 7)
+	#define U2P_R1_TX_RES_TUNE_MASK				GENMASK(10, 9)
+	#define U2P_R1_TX_RISE_TUNE_MASK			GENMASK(12, 11)
+	#define U2P_R1_TX_VREF_TUNE_MASK			GENMASK(16, 13)
+	#define U2P_R1_TX_FSLS_TUNE_MASK			GENMASK(20, 17)
+	#define U2P_R1_TX_HSXV_TUNE_MASK			GENMASK(22, 21)
+	#define U2P_R1_OTG_TUNE_MASK				GENMASK(25, 23)
+	#define U2P_R1_SQRX_TUNE_MASK				GENMASK(28, 26)
+	#define U2P_R1_COMP_DIS_TUNE_MASK			GENMASK(31, 29)
+
+/* bits [31:14] are read-only */
+#define U2P_R2							0x8
+	#define U2P_R2_DATA_IN_MASK				GENMASK(3, 0)
+	#define U2P_R2_DATA_IN_EN_MASK				GENMASK(7, 4)
+	#define U2P_R2_ADDR_MASK				GENMASK(11, 8)
+	#define U2P_R2_DATA_OUT_SEL				BIT(12)
+	#define U2P_R2_CLK					BIT(13)
+	#define U2P_R2_DATA_OUT_MASK				GENMASK(17, 14)
+	#define U2P_R2_ACA_PIN_RANGE_C				BIT(18)
+	#define U2P_R2_ACA_PIN_RANGE_B				BIT(19)
+	#define U2P_R2_ACA_PIN_RANGE_A				BIT(20)
+	#define U2P_R2_ACA_PIN_GND				BIT(21)
+	#define U2P_R2_ACA_PIN_FLOAT				BIT(22)
+	#define U2P_R2_CHARGE_DETECT				BIT(23)
+	#define U2P_R2_DEVICE_SESSION_VALID			BIT(24)
+	#define U2P_R2_ADP_PROBE				BIT(25)
+	#define U2P_R2_ADP_SENSE				BIT(26)
+	#define U2P_R2_SESSION_END				BIT(27)
+	#define U2P_R2_VBUS_VALID				BIT(28)
+	#define U2P_R2_B_VALID					BIT(29)
+	#define U2P_R2_A_VALID					BIT(30)
+	#define U2P_R2_ID_DIG					BIT(31)
+
+#define U2P_R3							0xc
+
+#define RESET_COMPLETE_TIME				500
+
+struct phy_meson_gxl_usb2_priv {
+	struct regmap		*regmap;
+	enum phy_mode		mode;
+	int			is_enabled;
+};
+
+static const struct regmap_config phy_meson_gxl_usb2_regmap_conf = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = U2P_R3,
+};
+
+static int phy_meson_gxl_usb2_reset(struct phy *phy)
+{
+	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
+
+	if (priv->is_enabled) {
+		/* reset the PHY and wait until settings are stabilized */
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
+				   U2P_R0_POWER_ON_RESET);
+		udelay(RESET_COMPLETE_TIME);
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
+				   0);
+		udelay(RESET_COMPLETE_TIME);
+	}
+
+	return 0;
+}
+
+static int phy_meson_gxl_usb2_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+	case PHY_MODE_USB_OTG:
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
+				   U2P_R0_DM_PULLDOWN);
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
+				   U2P_R0_DP_PULLDOWN);
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP, 0);
+		break;
+
+	case PHY_MODE_USB_DEVICE:
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DM_PULLDOWN,
+				   0);
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_DP_PULLDOWN,
+				   0);
+		regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_ID_PULLUP,
+				   U2P_R0_ID_PULLUP);
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	phy_meson_gxl_usb2_reset(phy);
+
+	priv->mode = mode;
+
+	return 0;
+}
+
+static int phy_meson_gxl_usb2_power_off(struct phy *phy)
+{
+	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
+
+	priv->is_enabled = 0;
+
+	/* power off the PHY by putting it into reset mode */
+	regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET,
+			   U2P_R0_POWER_ON_RESET);
+
+	return 0;
+}
+
+static int phy_meson_gxl_usb2_power_on(struct phy *phy)
+{
+	struct phy_meson_gxl_usb2_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	priv->is_enabled = 1;
+
+	/* power on the PHY by taking it out of reset mode */
+	regmap_update_bits(priv->regmap, U2P_R0, U2P_R0_POWER_ON_RESET, 0);
+
+	ret = phy_meson_gxl_usb2_set_mode(phy, priv->mode);
+	if (ret) {
+		phy_meson_gxl_usb2_power_off(phy);
+
+		dev_err(&phy->dev, "Failed to initialize PHY with mode %d\n",
+			priv->mode);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct phy_ops phy_meson_gxl_usb2_ops = {
+	.power_on	= phy_meson_gxl_usb2_power_on,
+	.power_off	= phy_meson_gxl_usb2_power_off,
+	.set_mode	= phy_meson_gxl_usb2_set_mode,
+	.reset		= phy_meson_gxl_usb2_reset,
+	.owner		= THIS_MODULE,
+};
+
+static int phy_meson_gxl_usb2_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	struct phy_meson_gxl_usb2_priv *priv;
+	struct phy *phy;
+	void __iomem *base;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, priv);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	switch (of_usb_get_dr_mode_by_phy(dev->of_node, -1)) {
+	case USB_DR_MODE_PERIPHERAL:
+		priv->mode = PHY_MODE_USB_DEVICE;
+		break;
+	case USB_DR_MODE_OTG:
+		priv->mode = PHY_MODE_USB_OTG;
+		break;
+	case USB_DR_MODE_HOST:
+	default:
+		priv->mode = PHY_MODE_USB_HOST;
+		break;
+	}
+
+	priv->regmap = devm_regmap_init_mmio(dev, base,
+					     &phy_meson_gxl_usb2_regmap_conf);
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+
+	phy = devm_phy_create(dev, NULL, &phy_meson_gxl_usb2_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, priv);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id phy_meson_gxl_usb2_of_match[] = {
+	{ .compatible = "amlogic,meson-gxl-usb2-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_meson_gxl_usb2_of_match);
+
+static struct platform_driver phy_meson_gxl_usb2_driver = {
+	.probe	= phy_meson_gxl_usb2_probe,
+	.driver	= {
+		.name		= "phy-meson-gxl-usb2",
+		.of_match_table	= phy_meson_gxl_usb2_of_match,
+	},
+};
+module_platform_driver(phy_meson_gxl_usb2_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Meson GXL and GXM USB2 PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-meson8b-usb2.c → drivers/phy/amlogic/phy-meson8b-usb2.c

 /*
- * Meson8b and GXBB USB2 PHY driver
+ * Meson8, Meson8b and GXBB USB2 PHY driver
  *
  * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
  *
@@ -266,6 +266,7 @@ static int phy_meson8b_usb2_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id phy_meson8b_usb2_of_match[] = {
+	{ .compatible = "amlogic,meson8-usb2-phy", },
 	{ .compatible = "amlogic,meson8b-usb2-phy", },
 	{ .compatible = "amlogic,meson-gxbb-usb2-phy", },
 	{ },
@@ -282,5 +283,5 @@ static struct platform_driver phy_meson8b_usb2_driver = {
 module_platform_driver(phy_meson8b_usb2_driver);
 
 MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
-MODULE_DESCRIPTION("Meson8b and GXBB USB2 PHY driver");
+MODULE_DESCRIPTION("Meson8, Meson8b and GXBB USB2 PHY driver");
 MODULE_LICENSE("GPL");

drivers/phy/broadcom/Kconfig

+#
+# Phy drivers for Broadcom platforms
+#
+config PHY_CYGNUS_PCIE
+	tristate "Broadcom Cygnus PCIe PHY driver"
+	depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
+	select GENERIC_PHY
+	default ARCH_BCM_CYGNUS
+	help
+	  Enable this to support the Broadcom Cygnus PCIe PHY.
+	  If unsure, say N.
+
+config BCM_KONA_USB2_PHY
+	tristate "Broadcom Kona USB2 PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support the Broadcom Kona USB 2.0 PHY.
+
+config PHY_BCM_NS_USB2
+	tristate "Broadcom Northstar USB 2.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support Broadcom USB 2.0 PHY connected to the USB
+	  controller on Northstar family.
+
+config PHY_BCM_NS_USB3
+	tristate "Broadcom Northstar USB 3.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	select MDIO_DEVICE
+	help
+	  Enable this to support Broadcom USB 3.0 PHY connected to the USB
+	  controller on Northstar family.
+
+config PHY_NS2_PCIE
+	tristate "Broadcom Northstar2 PCIe PHY driver"
+	depends on OF && MDIO_BUS_MUX_BCM_IPROC
+	select GENERIC_PHY
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom Northstar2 PCIe PHY.
+	  If unsure, say N.
+
+config PHY_NS2_USB_DRD
+	tristate "Broadcom Northstar2 USB DRD PHY support"
+	depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
+	select GENERIC_PHY
+	select EXTCON
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom Northstar2 USB DRD PHY.
+	  This driver initializes the PHY in either HOST or DEVICE mode.
+	  The host or device configuration is read from device tree.
+
+	  If unsure, say N.
+
+config PHY_BRCM_SATA
+	tristate "Broadcom SATA PHY driver"
+	depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || COMPILE_TEST
+	depends on OF
+	select GENERIC_PHY
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom SATA PHY.
+	  If unsure, say N.

drivers/phy/broadcom/Makefile

+obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
+obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
+obj-$(CONFIG_PHY_BCM_NS_USB3)		+= phy-bcm-ns-usb3.o
+obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
+obj-$(CONFIG_PHY_NS2_USB_DRD)		+= phy-bcm-ns2-usbdrd.o
+obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o

drivers/phy/phy-bcm-ns-usb3.c → drivers/phy/broadcom/phy-bcm-ns-usb3.c

@@ -16,7 +16,9 @@
 #include <linux/bcma/bcma.h>
 #include <linux/delay.h>
 #include <linux/err.h>
+#include <linux/mdio.h>
 #include <linux/module.h>
+#include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
@@ -52,7 +54,10 @@ struct bcm_ns_usb3 {
 	enum bcm_ns_family family;
 	void __iomem *dmp;
 	void __iomem *ccb_mii;
+	struct mdio_device *mdiodev;
 	struct phy *phy;
+
+	int (*phy_write)(struct bcm_ns_usb3 *usb3, u16 reg, u16 value);
 };
 
 static const struct of_device_id bcm_ns_usb3_id_table[] = {
@@ -68,63 +73,16 @@ static const struct of_device_id bcm_ns_usb3_id_table[] = {
 };
 MODULE_DEVICE_TABLE(of, bcm_ns_usb3_id_table);
 
-static int bcm_ns_usb3_wait_reg(struct bcm_ns_usb3 *usb3, void __iomem *addr,
-				u32 mask, u32 value, unsigned long timeout)
-{
-	unsigned long deadline = jiffies + timeout;
-	u32 val;
-
-	do {
-		val = readl(addr);
-		if ((val & mask) == value)
-			return 0;
-		cpu_relax();
-		udelay(10);
-	} while (!time_after_eq(jiffies, deadline));
-
-	dev_err(usb3->dev, "Timeout waiting for register %p\n", addr);
-
-	return -EBUSY;
-}
-
-static inline int bcm_ns_usb3_mii_mng_wait_idle(struct bcm_ns_usb3 *usb3)
-{
-	return bcm_ns_usb3_wait_reg(usb3, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL,
-				    0x0100, 0x0000,
-				    usecs_to_jiffies(BCM_NS_USB3_MII_MNG_TIMEOUT_US));
-}
-
 static int bcm_ns_usb3_mdio_phy_write(struct bcm_ns_usb3 *usb3, u16 reg,
 				      u16 value)
 {
-	u32 tmp = 0;
-	int err;
-
-	err = bcm_ns_usb3_mii_mng_wait_idle(usb3);
-	if (err < 0) {
-		dev_err(usb3->dev, "Couldn't write 0x%08x value\n", value);
-		return err;
-	}
-
-	/* TODO: Use a proper MDIO bus layer */
-	tmp |= 0x58020000; /* Magic value for MDIO PHY write */
-	tmp |= reg << 18;
-	tmp |= value;
-	writel(tmp, usb3->ccb_mii + BCMA_CCB_MII_MNG_CMD_DATA);
-
-	return 0;
+	return usb3->phy_write(usb3, reg, value);
 }
 
 static int bcm_ns_usb3_phy_init_ns_bx(struct bcm_ns_usb3 *usb3)
 {
 	int err;
 
-	/* Enable MDIO. Setting MDCDIV as 26  */
-	writel(0x0000009a, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL);
-
-	/* Wait for MDIO? */
-	udelay(2);
-
 	/* USB3 PLL Block */
 	err = bcm_ns_usb3_mdio_phy_write(usb3, BCM_NS_USB3_PHY_BASE_ADDR_REG,
 					 BCM_NS_USB3_PHY_PLL30_BLOCK);
@@ -143,9 +101,6 @@ static int bcm_ns_usb3_phy_init_ns_bx(struct bcm_ns_usb3 *usb3)
 	/* Deaaserting PLL Reset */
 	bcm_ns_usb3_mdio_phy_write(usb3, BCM_NS_USB3_PLLA_CONTROL1, 0x8000);
 
-	/* Waiting MII Mgt interface idle */
-	bcm_ns_usb3_mii_mng_wait_idle(usb3);
-
 	/* Deasserting USB3 system reset */
 	writel(0, usb3->dmp + BCMA_RESET_CTL);
 
@@ -169,9 +124,6 @@ static int bcm_ns_usb3_phy_init_ns_bx(struct bcm_ns_usb3 *usb3)
 	/* Enabling SSC */
 	bcm_ns_usb3_mdio_phy_write(usb3, BCM_NS_USB3_TX_PMD_CONTROL1, 0x1003);
 
-	/* Waiting MII Mgt interface idle */
-	bcm_ns_usb3_mii_mng_wait_idle(usb3);
-
 	return 0;
 }
 
@@ -179,12 +131,6 @@ static int bcm_ns_usb3_phy_init_ns_ax(struct bcm_ns_usb3 *usb3)
 {
 	int err;
 
-	/* Enable MDIO. Setting MDCDIV as 26  */
-	writel(0x0000009a, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL);
-
-	/* Wait for MDIO? */
-	udelay(2);
-
 	/* PLL30 block */
 	err = bcm_ns_usb3_mdio_phy_write(usb3, BCM_NS_USB3_PHY_BASE_ADDR_REG,
 					 BCM_NS_USB3_PHY_PLL30_BLOCK);
@@ -205,9 +151,6 @@ static int bcm_ns_usb3_phy_init_ns_ax(struct bcm_ns_usb3 *usb3)
 
 	bcm_ns_usb3_mdio_phy_write(usb3, BCM_NS_USB3_TX_PMD_CONTROL1, 0x1003);
 
-	/* Waiting MII Mgt interface idle */
-	bcm_ns_usb3_mii_mng_wait_idle(usb3);
-
 	/* Deasserting USB3 system reset */
 	writel(0, usb3->dmp + BCMA_RESET_CTL);
 
@@ -242,6 +185,128 @@ static const struct phy_ops ops = {
 	.owner		= THIS_MODULE,
 };
 
+/**************************************************
+ * MDIO driver code
+ **************************************************/
+
+static int bcm_ns_usb3_mdiodev_phy_write(struct bcm_ns_usb3 *usb3, u16 reg,
+					 u16 value)
+{
+	struct mdio_device *mdiodev = usb3->mdiodev;
+
+	return mdiobus_write(mdiodev->bus, mdiodev->addr, reg, value);
+}
+
+static int bcm_ns_usb3_mdio_probe(struct mdio_device *mdiodev)
+{
+	struct device *dev = &mdiodev->dev;
+	const struct of_device_id *of_id;
+	struct phy_provider *phy_provider;
+	struct device_node *syscon_np;
+	struct bcm_ns_usb3 *usb3;
+	struct resource res;
+	int err;
+
+	usb3 = devm_kzalloc(dev, sizeof(*usb3), GFP_KERNEL);
+	if (!usb3)
+		return -ENOMEM;
+
+	usb3->dev = dev;
+	usb3->mdiodev = mdiodev;
+
+	of_id = of_match_device(bcm_ns_usb3_id_table, dev);
+	if (!of_id)
+		return -EINVAL;
+	usb3->family = (enum bcm_ns_family)of_id->data;
+
+	syscon_np = of_parse_phandle(dev->of_node, "usb3-dmp-syscon", 0);
+	err = of_address_to_resource(syscon_np, 0, &res);
+	of_node_put(syscon_np);
+	if (err)
+		return err;
+
+	usb3->dmp = devm_ioremap_resource(dev, &res);
+	if (IS_ERR(usb3->dmp)) {
+		dev_err(dev, "Failed to map DMP regs\n");
+		return PTR_ERR(usb3->dmp);
+	}
+
+	usb3->phy_write = bcm_ns_usb3_mdiodev_phy_write;
+
+	usb3->phy = devm_phy_create(dev, NULL, &ops);
+	if (IS_ERR(usb3->phy)) {
+		dev_err(dev, "Failed to create PHY\n");
+		return PTR_ERR(usb3->phy);
+	}
+
+	phy_set_drvdata(usb3->phy, usb3);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct mdio_driver bcm_ns_usb3_mdio_driver = {
+	.mdiodrv = {
+		.driver = {
+			.name = "bcm_ns_mdio_usb3",
+			.of_match_table = bcm_ns_usb3_id_table,
+		},
+	},
+	.probe = bcm_ns_usb3_mdio_probe,
+};
+
+/**************************************************
+ * Platform driver code
+ **************************************************/
+
+static int bcm_ns_usb3_wait_reg(struct bcm_ns_usb3 *usb3, void __iomem *addr,
+				u32 mask, u32 value, unsigned long timeout)
+{
+	unsigned long deadline = jiffies + timeout;
+	u32 val;
+
+	do {
+		val = readl(addr);
+		if ((val & mask) == value)
+			return 0;
+		cpu_relax();
+		udelay(10);
+	} while (!time_after_eq(jiffies, deadline));
+
+	dev_err(usb3->dev, "Timeout waiting for register %p\n", addr);
+
+	return -EBUSY;
+}
+
+static inline int bcm_ns_usb3_mii_mng_wait_idle(struct bcm_ns_usb3 *usb3)
+{
+	return bcm_ns_usb3_wait_reg(usb3, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL,
+				    0x0100, 0x0000,
+				    usecs_to_jiffies(BCM_NS_USB3_MII_MNG_TIMEOUT_US));
+}
+
+static int bcm_ns_usb3_platform_phy_write(struct bcm_ns_usb3 *usb3, u16 reg,
+					  u16 value)
+{
+	u32 tmp = 0;
+	int err;
+
+	err = bcm_ns_usb3_mii_mng_wait_idle(usb3);
+	if (err < 0) {
+		dev_err(usb3->dev, "Couldn't write 0x%08x value\n", value);
+		return err;
+	}
+
+	/* TODO: Use a proper MDIO bus layer */
+	tmp |= 0x58020000; /* Magic value for MDIO PHY write */
+	tmp |= reg << 18;
+	tmp |= value;
+	writel(tmp, usb3->ccb_mii + BCMA_CCB_MII_MNG_CMD_DATA);
+
+	return bcm_ns_usb3_mii_mng_wait_idle(usb3);
+}
+
 static int bcm_ns_usb3_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -275,6 +340,14 @@ static int bcm_ns_usb3_probe(struct platform_device *pdev)
 		return PTR_ERR(usb3->ccb_mii);
 	}
 
+	/* Enable MDIO. Setting MDCDIV as 26  */
+	writel(0x0000009a, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL);
+
+	/* Wait for MDIO? */
+	udelay(2);
+
+	usb3->phy_write = bcm_ns_usb3_platform_phy_write;
+
 	usb3->phy = devm_phy_create(dev, NULL, &ops);
 	if (IS_ERR(usb3->phy)) {
 		dev_err(dev, "Failed to create PHY\n");
@@ -298,6 +371,35 @@ static struct platform_driver bcm_ns_usb3_driver = {
 		.of_match_table = bcm_ns_usb3_id_table,
 	},
 };
-module_platform_driver(bcm_ns_usb3_driver);
+
+static int __init bcm_ns_usb3_module_init(void)
+{
+	int err;
+
+	/*
+	 * For backward compatibility we register as MDIO and platform driver.
+	 * After getting MDIO binding commonly used (e.g. switching all DT files
+	 * to use it) we should deprecate the old binding and eventually drop
+	 * support for it.
+	 */
+
+	err = mdio_driver_register(&bcm_ns_usb3_mdio_driver);
+	if (err)
+		return err;
+
+	err = platform_driver_register(&bcm_ns_usb3_driver);
+	if (err)
+		mdio_driver_unregister(&bcm_ns_usb3_mdio_driver);
+
+	return err;
+}
+module_init(bcm_ns_usb3_module_init);
+
+static void __exit bcm_ns_usb3_module_exit(void)
+{
+	platform_driver_unregister(&bcm_ns_usb3_driver);
+	mdio_driver_unregister(&bcm_ns_usb3_mdio_driver);
+}
+module_exit(bcm_ns_usb3_module_exit)
 
 MODULE_LICENSE("GPL v2");

drivers/phy/phy-brcm-sata.c → drivers/phy/broadcom/phy-brcm-sata.c

@@ -46,6 +46,7 @@ enum brcm_sata_phy_version {
 	BRCM_SATA_PHY_STB_40NM,
 	BRCM_SATA_PHY_IPROC_NS2,
 	BRCM_SATA_PHY_IPROC_NSP,
+	BRCM_SATA_PHY_IPROC_SR,
 };
 
 struct brcm_sata_port {
@@ -81,12 +82,17 @@ enum sata_phy_regs {
 	PLL_ACTRL2				= 0x8b,
 	PLL_ACTRL2_SELDIV_MASK			= 0x1f,
 	PLL_ACTRL2_SELDIV_SHIFT			= 9,
+	PLL_ACTRL6				= 0x86,
 
 	PLL1_REG_BANK				= 0x060,
 	PLL1_ACTRL2				= 0x82,
 	PLL1_ACTRL3				= 0x83,
 	PLL1_ACTRL4				= 0x84,
 
+	TX_REG_BANK				= 0x070,
+	TX_ACTRL0				= 0x80,
+	TX_ACTRL0_TXPOL_FLIP			= BIT(6),
+
 	OOB_REG_BANK				= 0x150,
 	OOB1_REG_BANK				= 0x160,
 	OOB_CTRL1				= 0x80,
@@ -347,6 +353,68 @@ static int brcm_nsp_sata_init(struct brcm_sata_port *port)
 	return 0;
 }
 
+/* SR PHY PLL0 registers */
+#define SR_PLL0_ACTRL6_MAGIC			0xa
+
+/* SR PHY PLL1 registers */
+#define SR_PLL1_ACTRL2_MAGIC			0x32
+#define SR_PLL1_ACTRL3_MAGIC			0x2
+#define SR_PLL1_ACTRL4_MAGIC			0x3e8
+
+static int brcm_sr_sata_init(struct brcm_sata_port *port)
+{
+	struct brcm_sata_phy *priv = port->phy_priv;
+	struct device *dev = port->phy_priv->dev;
+	void __iomem *base = priv->phy_base;
+	unsigned int val, try;
+
+	/* Configure PHY PLL register bank 1 */
+	val = SR_PLL1_ACTRL2_MAGIC;
+	brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
+	val = SR_PLL1_ACTRL3_MAGIC;
+	brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
+	val = SR_PLL1_ACTRL4_MAGIC;
+	brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
+
+	/* Configure PHY PLL register bank 0 */
+	val = SR_PLL0_ACTRL6_MAGIC;
+	brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
+
+	/* Wait for PHY PLL lock by polling pll_lock bit */
+	try = 50;
+	do {
+		val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+					BLOCK0_XGXSSTATUS);
+		if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
+			break;
+		msleep(20);
+		try--;
+	} while (try);
+
+	if ((val & BLOCK0_XGXSSTATUS_PLL_LOCK) == 0) {
+		/* PLL did not lock; give up */
+		dev_err(dev, "port%d PLL did not lock\n", port->portnum);
+		return -ETIMEDOUT;
+	}
+
+	/* Invert Tx polarity */
+	brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL0,
+			 ~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP);
+
+	/* Configure OOB control to handle 100MHz reference clock */
+	val = ((0xc << OOB_CTRL1_BURST_MAX_SHIFT) |
+		(0x4 << OOB_CTRL1_BURST_MIN_SHIFT) |
+		(0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) |
+		(0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT));
+	brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
+	val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) |
+		(0x2 << OOB_CTRL2_BURST_CNT_SHIFT) |
+		(0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT));
+	brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
+
+	return 0;
+}
+
 static int brcm_sata_phy_init(struct phy *phy)
 {
 	int rc;
@@ -363,6 +431,9 @@ static int brcm_sata_phy_init(struct phy *phy)
 	case BRCM_SATA_PHY_IPROC_NSP:
 		rc = brcm_nsp_sata_init(port);
 		break;
+	case BRCM_SATA_PHY_IPROC_SR:
+		rc = brcm_sr_sata_init(port);
+		break;
 	default:
 		rc = -ENODEV;
 	}
@@ -384,6 +455,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
 	  .data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
 	{ .compatible = "brcm,iproc-nsp-sata-phy",
 	  .data = (void *)BRCM_SATA_PHY_IPROC_NSP },
+	{ .compatible	= "brcm,iproc-sr-sata-phy",
+	  .data = (void *)BRCM_SATA_PHY_IPROC_SR },
 	{},
 };
 MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);

drivers/phy/hisilicon/Kconfig

+#
+# Phy drivers for Hisilicon platforms
+#
+config PHY_HI6220_USB
+	tristate "hi6220 USB PHY support"
+	depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the HISILICON HI6220 USB PHY.
+
+	  To compile this driver as a module, choose M here.
+
+config PHY_HIX5HD2_SATA
+	tristate "HIX5HD2 SATA PHY Driver"
+	depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Support for SATA PHY on Hisilicon hix5hd2 Soc.

drivers/phy/hisilicon/Makefile

+obj-$(CONFIG_PHY_HI6220_USB)		+= phy-hi6220-usb.o
+obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o

drivers/phy/marvell/Kconfig

+#
+# Phy drivers for Marvell platforms
+#
+config ARMADA375_USBCLUSTER_PHY
+	def_bool y
+	depends on MACH_ARMADA_375 || COMPILE_TEST
+	depends on OF && HAS_IOMEM
+	select GENERIC_PHY
+
+config PHY_BERLIN_SATA
+	tristate "Marvell Berlin SATA PHY driver"
+	depends on ARCH_BERLIN && HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the SATA PHY on Marvell Berlin SoCs.
+
+config PHY_BERLIN_USB
+	tristate "Marvell Berlin USB PHY Driver"
+	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the USB PHY on Marvell Berlin SoCs.
+
+config PHY_MVEBU_SATA
+	def_bool y
+	depends on ARCH_DOVE || MACH_DOVE || MACH_KIRKWOOD
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_PXA_28NM_HSIC
+	tristate "Marvell USB HSIC 28nm PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell USB HSIC PHY driver for Marvell
+	  SoC. This driver will do the PHY initialization and shutdown.
+	  The PHY driver will be used by Marvell ehci driver.
+
+	  To compile this driver as a module, choose M here.
+
+config PHY_PXA_28NM_USB2
+	tristate "Marvell USB 2.0 28nm PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell USB 2.0 PHY driver for Marvell
+	  SoC. This driver will do the PHY initialization and shutdown.
+	  The PHY driver will be used by Marvell udc/ehci/otg driver.
+
+	  To compile this driver as a module, choose M here.

drivers/phy/marvell/Makefile

+obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
+obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
+obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
+obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
+obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o

drivers/phy/motorola/Kconfig

+#
+# Phy drivers for Motorola devices
+#
+config PHY_CPCAP_USB
+	tristate "CPCAP PMIC USB PHY driver"
+	depends on USB_SUPPORT && IIO
+	depends on USB_MUSB_HDRC || USB_MUSB_HDRC=n
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this for USB to work on Motorola phones and tablets
+	  such as Droid 4.

drivers/phy/motorola/Makefile

+#
+# Makefile for the phy drivers.
+#
+
+obj-$(CONFIG_PHY_CPCAP_USB)		+= phy-cpcap-usb.o

drivers/phy/qualcomm/Kconfig

+#
+# Phy drivers for Qualcomm platforms
+#
+config PHY_QCOM_APQ8064_SATA
+	tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
+	depends on ARCH_QCOM
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_QCOM_IPQ806X_SATA
+	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
+	depends on ARCH_QCOM
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_QCOM_QMP
+	tristate "Qualcomm QMP PHY Driver"
+	depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support the QMP PHY transceiver that is used
+	  with controllers such as PCIe, UFS, and USB on Qualcomm chips.
+
+config PHY_QCOM_QUSB2
+	tristate "Qualcomm QUSB2 PHY Driver"
+	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	depends on NVMEM || !NVMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
+	  controllers on Qualcomm chips. This driver supports the high-speed
+	  PHY which is usually paired with either the ChipIdea or Synopsys DWC3
+	  USB IPs on MSM SOCs.
+
+config PHY_QCOM_UFS
+	tristate "Qualcomm UFS PHY driver"
+	depends on OF && ARCH_QCOM
+	select GENERIC_PHY
+	help
+	  Support for UFS PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS
+	tristate "Qualcomm USB HS PHY module"
+	depends on USB_ULPI_BUS
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Support for the USB high-speed ULPI compliant phy on Qualcomm
+	  chipsets.
+
+config PHY_QCOM_USB_HSIC
+	tristate "Qualcomm USB HSIC ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.

drivers/phy/qualcomm/Makefile

+obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_QMP)		+= phy-qcom-qmp.o
+obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs-qmp-20nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o

drivers/phy/phy-qcom-usb-hs.c → drivers/phy/qualcomm/phy-qcom-usb-hs.c

@@ -11,12 +11,11 @@
 #include <linux/clk.h>
 #include <linux/regulator/consumer.h>
 #include <linux/of_device.h>
+#include <linux/phy/phy.h>
 #include <linux/reset.h>
 #include <linux/extcon.h>
 #include <linux/notifier.h>
 
-#include "ulpi_phy.h"
-
 #define ULPI_PWR_CLK_MNG_REG		0x88
 # define ULPI_PWR_OTG_COMP_DISABLE	BIT(0)
 

drivers/phy/phy-qcom-usb-hsic.c → drivers/phy/qualcomm/phy-qcom-usb-hsic.c

@@ -8,13 +8,12 @@
 #include <linux/module.h>
 #include <linux/ulpi/driver.h>
 #include <linux/ulpi/regs.h>
+#include <linux/phy/phy.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/pinctrl/pinctrl-state.h>
 #include <linux/delay.h>
 #include <linux/clk.h>
 
-#include "ulpi_phy.h"
-
 #define ULPI_HSIC_CFG		0x30
 #define ULPI_HSIC_IO_CAL	0x33
 

drivers/phy/renesas/Kconfig

+#
+# Phy drivers for Renesas platforms
+#
+config PHY_RCAR_GEN2
+	tristate "Renesas R-Car generation 2 USB PHY driver"
+	depends on ARCH_RENESAS
+	depends on GENERIC_PHY
+	help
+	  Support for USB PHY found on Renesas R-Car generation 2 SoCs.
+
+config PHY_RCAR_GEN3_USB2
+	tristate "Renesas R-Car generation 3 USB 2.0 PHY driver"
+	depends on ARCH_RENESAS
+	depends on EXTCON
+	select GENERIC_PHY
+	help
+	  Support for USB 2.0 PHY found on Renesas R-Car generation 3 SoCs.
+
+config PHY_RCAR_GEN3_USB3
+	tristate "Renesas R-Car generation 3 USB 3.0 PHY driver"
+	depends on ARCH_RENESAS || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Support for USB 3.0 PHY found on Renesas R-Car generation 3 SoCs.

drivers/phy/renesas/Makefile

+obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
+obj-$(CONFIG_PHY_RCAR_GEN3_USB2)	+= phy-rcar-gen3-usb2.o
+obj-$(CONFIG_PHY_RCAR_GEN3_USB3)	+= phy-rcar-gen3-usb3.o

drivers/phy/renesas/phy-rcar-gen3-usb3.c

+/*
+ * Renesas R-Car Gen3 for USB3.0 PHY driver
+ *
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#define USB30_CLKSET0		0x034
+#define USB30_CLKSET1		0x036
+#define USB30_SSC_SET		0x038
+#define USB30_PHY_ENABLE	0x060
+#define USB30_VBUS_EN		0x064
+
+/* USB30_CLKSET0 */
+#define CLKSET0_PRIVATE			0x05c0
+#define CLKSET0_USB30_FSEL_USB_EXTAL	0x0002
+
+/* USB30_CLKSET1 */
+#define CLKSET1_USB30_PLL_MULTI_SHIFT		6
+#define CLKSET1_USB30_PLL_MULTI_USB_EXTAL	(0x64 << \
+						 CLKSET1_USB30_PLL_MULTI_SHIFT)
+#define CLKSET1_PHYRESET	BIT(4)	/* 1: reset */
+#define CLKSET1_REF_CLKDIV	BIT(3)	/* 1: USB_EXTAL */
+#define CLKSET1_PRIVATE_2_1	BIT(1)	/* Write B'01 */
+#define CLKSET1_REF_CLK_SEL	BIT(0)	/* 1: USB3S0_CLK_P */
+
+/* USB30_SSC_SET */
+#define SSC_SET_SSC_EN		BIT(12)
+#define SSC_SET_RANGE_SHIFT	9
+#define SSC_SET_RANGE_4980	(0x0 << SSC_SET_RANGE_SHIFT)
+#define SSC_SET_RANGE_4492	(0x1 << SSC_SET_RANGE_SHIFT)
+#define SSC_SET_RANGE_4003	(0x2 << SSC_SET_RANGE_SHIFT)
+
+/* USB30_PHY_ENABLE */
+#define PHY_ENABLE_RESET_EN	BIT(4)
+
+/* USB30_VBUS_EN */
+#define VBUS_EN_VBUS_EN		BIT(1)
+
+struct rcar_gen3_usb3 {
+	void __iomem *base;
+	struct phy *phy;
+	u32 ssc_range;
+	bool usb3s_clk;
+	bool usb_extal;
+};
+
+static void write_clkset1_for_usb_extal(struct rcar_gen3_usb3 *r, bool reset)
+{
+	u16 val = CLKSET1_USB30_PLL_MULTI_USB_EXTAL |
+		  CLKSET1_REF_CLKDIV | CLKSET1_PRIVATE_2_1;
+
+	if (reset)
+		val |= CLKSET1_PHYRESET;
+
+	writew(val, r->base + USB30_CLKSET1);
+}
+
+static void rcar_gen3_phy_usb3_enable_ssc(struct rcar_gen3_usb3 *r)
+{
+	u16 val = SSC_SET_SSC_EN;
+
+	switch (r->ssc_range) {
+	case 4980:
+		val |= SSC_SET_RANGE_4980;
+		break;
+	case 4492:
+		val |= SSC_SET_RANGE_4492;
+		break;
+	case 4003:
+		val |= SSC_SET_RANGE_4003;
+		break;
+	default:
+		dev_err(&r->phy->dev, "%s: unsupported range (%x)\n", __func__,
+			r->ssc_range);
+		return;
+	}
+
+	writew(val, r->base + USB30_SSC_SET);
+}
+
+static void rcar_gen3_phy_usb3_select_usb_extal(struct rcar_gen3_usb3 *r)
+{
+	write_clkset1_for_usb_extal(r, false);
+	if (r->ssc_range)
+		rcar_gen3_phy_usb3_enable_ssc(r);
+	writew(CLKSET0_PRIVATE | CLKSET0_USB30_FSEL_USB_EXTAL,
+	       r->base + USB30_CLKSET0);
+	writew(PHY_ENABLE_RESET_EN, r->base + USB30_PHY_ENABLE);
+	write_clkset1_for_usb_extal(r, true);
+	usleep_range(10, 20);
+	write_clkset1_for_usb_extal(r, false);
+}
+
+static int rcar_gen3_phy_usb3_init(struct phy *p)
+{
+	struct rcar_gen3_usb3 *r = phy_get_drvdata(p);
+
+	dev_vdbg(&r->phy->dev, "%s: enter (%d, %d, %d)\n", __func__,
+		 r->usb3s_clk, r->usb_extal, r->ssc_range);
+
+	if (!r->usb3s_clk && r->usb_extal)
+		rcar_gen3_phy_usb3_select_usb_extal(r);
+
+	/* Enables VBUS detection anyway */
+	writew(VBUS_EN_VBUS_EN, r->base + USB30_VBUS_EN);
+
+	return 0;
+}
+
+static const struct phy_ops rcar_gen3_phy_usb3_ops = {
+	.init		= rcar_gen3_phy_usb3_init,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id rcar_gen3_phy_usb3_match_table[] = {
+	{ .compatible = "renesas,rcar-gen3-usb3-phy" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rcar_gen3_phy_usb3_match_table);
+
+static int rcar_gen3_phy_usb3_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rcar_gen3_usb3 *r;
+	struct phy_provider *provider;
+	struct resource *res;
+	int ret = 0;
+	struct clk *clk;
+
+	if (!dev->of_node) {
+		dev_err(dev, "This driver needs device tree\n");
+		return -EINVAL;
+	}
+
+	r = devm_kzalloc(dev, sizeof(*r), GFP_KERNEL);
+	if (!r)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	r->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(r->base))
+		return PTR_ERR(r->base);
+
+	clk = devm_clk_get(dev, "usb3s_clk");
+	if (!IS_ERR(clk) && !clk_prepare_enable(clk)) {
+		r->usb3s_clk = !!clk_get_rate(clk);
+		clk_disable_unprepare(clk);
+	}
+	clk = devm_clk_get(dev, "usb_extal");
+	if (!IS_ERR(clk) && !clk_prepare_enable(clk)) {
+		r->usb_extal = !!clk_get_rate(clk);
+		clk_disable_unprepare(clk);
+	}
+
+	if (!r->usb3s_clk && !r->usb_extal) {
+		dev_err(dev, "This driver needs usb3s_clk and/or usb_extal\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	/*
+	 * devm_phy_create() will call pm_runtime_enable(&phy->dev);
+	 * And then, phy-core will manage runtime pm for this device.
+	 */
+	pm_runtime_enable(dev);
+
+	r->phy = devm_phy_create(dev, NULL, &rcar_gen3_phy_usb3_ops);
+	if (IS_ERR(r->phy)) {
+		dev_err(dev, "Failed to create USB3 PHY\n");
+		ret = PTR_ERR(r->phy);
+		goto error;
+	}
+
+	of_property_read_u32(dev->of_node, "renesas,ssc-range", &r->ssc_range);
+
+	platform_set_drvdata(pdev, r);
+	phy_set_drvdata(r->phy, r);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider)) {
+		dev_err(dev, "Failed to register PHY provider\n");
+		ret = PTR_ERR(provider);
+		goto error;
+	}
+
+	return 0;
+
+error:
+	pm_runtime_disable(dev);
+
+	return ret;
+}
+
+static int rcar_gen3_phy_usb3_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+
+	return 0;
+};
+
+static struct platform_driver rcar_gen3_phy_usb3_driver = {
+	.driver = {
+		.name		= "phy_rcar_gen3_usb3",
+		.of_match_table	= rcar_gen3_phy_usb3_match_table,
+	},
+	.probe	= rcar_gen3_phy_usb3_probe,
+	.remove = rcar_gen3_phy_usb3_remove,
+};
+module_platform_driver(rcar_gen3_phy_usb3_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Renesas R-Car Gen3 USB 3.0 PHY");
+MODULE_AUTHOR("Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>");

drivers/phy/rockchip/Kconfig

+#
+# Phy drivers for Rockchip platforms
+#
+config PHY_ROCKCHIP_DP
+	tristate "Rockchip Display Port PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip Display Port PHY.
+
+config PHY_ROCKCHIP_EMMC
+	tristate "Rockchip EMMC PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip EMMC PHY.
+
+config PHY_ROCKCHIP_INNO_USB2
+	tristate "Rockchip INNO USB2PHY Driver"
+	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
+	depends on COMMON_CLK
+	depends on EXTCON
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_COMMON
+	help
+	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+
+config PHY_ROCKCHIP_PCIE
+	tristate "Rockchip PCIe PHY Driver"
+	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the Rockchip PCIe PHY.
+
+config PHY_ROCKCHIP_TYPEC
+	tristate "Rockchip TYPEC PHY Driver"
+	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	select EXTCON
+	select GENERIC_PHY
+	select RESET_CONTROLLER
+	help
+	  Enable this to support the Rockchip USB TYPEC PHY.
+
+config PHY_ROCKCHIP_USB
+	tristate "Rockchip USB2 PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip USB 2.0 PHY.

drivers/phy/rockchip/Makefile

+obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
+obj-$(CONFIG_PHY_ROCKCHIP_EMMC)		+= phy-rockchip-emmc.o
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
+obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
+obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
+obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o

drivers/phy/phy-rockchip-inno-usb2.c → drivers/phy/rockchip/phy-rockchip-inno-usb2.c

@@ -406,7 +406,8 @@ static int rockchip_usb2phy_init(struct phy *phy)
 	mutex_lock(&rport->mutex);
 
 	if (rport->port_id == USB2PHY_PORT_OTG) {
-		if (rport->mode != USB_DR_MODE_HOST) {
+		if (rport->mode != USB_DR_MODE_HOST &&
+		    rport->mode != USB_DR_MODE_UNKNOWN) {
 			/* clear bvalid status and enable bvalid detect irq */
 			ret = property_enable(rphy,
 					      &rport->port_cfg->bvalid_det_clr,
@@ -421,7 +422,7 @@ static int rockchip_usb2phy_init(struct phy *phy)
 				goto out;
 
 			schedule_delayed_work(&rport->otg_sm_work,
-					      OTG_SCHEDULE_DELAY);
+					      OTG_SCHEDULE_DELAY * 3);
 		} else {
 			/* If OTG works in host only mode, do nothing. */
 			dev_dbg(&rport->phy->dev, "mode %d\n", rport->mode);
@@ -463,6 +464,9 @@ static int rockchip_usb2phy_power_on(struct phy *phy)
 	if (ret)
 		return ret;
 
+	/* waiting for the utmi_clk to become stable */
+	usleep_range(1500, 2000);
+
 	rport->suspended = false;
 	return 0;
 }
@@ -493,7 +497,8 @@ static int rockchip_usb2phy_exit(struct phy *phy)
 	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
 
 	if (rport->port_id == USB2PHY_PORT_OTG &&
-	    rport->mode != USB_DR_MODE_HOST) {
+	    rport->mode != USB_DR_MODE_HOST &&
+	    rport->mode != USB_DR_MODE_UNKNOWN) {
 		cancel_delayed_work_sync(&rport->otg_sm_work);
 		cancel_delayed_work_sync(&rport->chg_work);
 	} else if (rport->port_id == USB2PHY_PORT_HOST)
@@ -970,7 +975,8 @@ static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
 	mutex_init(&rport->mutex);
 
 	rport->mode = of_usb_get_dr_mode_by_phy(child_np, -1);
-	if (rport->mode == USB_DR_MODE_HOST) {
+	if (rport->mode == USB_DR_MODE_HOST ||
+	    rport->mode == USB_DR_MODE_UNKNOWN) {
 		ret = 0;
 		goto out;
 	}
@@ -1138,6 +1144,65 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
 	return ret;
 }
 
+static const struct rockchip_usb2phy_cfg rk3228_phy_cfgs[] = {
+	{
+		.reg = 0x760,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0x0768, 4, 4, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x0760, 15, 0, 0, 0x1d1 },
+				.bvalid_det_en	= { 0x0680, 3, 3, 0, 1 },
+				.bvalid_det_st	= { 0x0690, 3, 3, 0, 1 },
+				.bvalid_det_clr	= { 0x06a0, 3, 3, 0, 1 },
+				.ls_det_en	= { 0x0680, 2, 2, 0, 1 },
+				.ls_det_st	= { 0x0690, 2, 2, 0, 1 },
+				.ls_det_clr	= { 0x06a0, 2, 2, 0, 1 },
+				.utmi_bvalid	= { 0x0480, 4, 4, 0, 1 },
+				.utmi_ls	= { 0x0480, 3, 2, 0, 1 },
+			},
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0764, 15, 0, 0, 0x1d1 },
+				.ls_det_en	= { 0x0680, 4, 4, 0, 1 },
+				.ls_det_st	= { 0x0690, 4, 4, 0, 1 },
+				.ls_det_clr	= { 0x06a0, 4, 4, 0, 1 }
+			}
+		},
+		.chg_det = {
+			.opmode		= { 0x0760, 3, 0, 5, 1 },
+			.cp_det		= { 0x0884, 4, 4, 0, 1 },
+			.dcp_det	= { 0x0884, 3, 3, 0, 1 },
+			.dp_det		= { 0x0884, 5, 5, 0, 1 },
+			.idm_sink_en	= { 0x0768, 8, 8, 0, 1 },
+			.idp_sink_en	= { 0x0768, 7, 7, 0, 1 },
+			.idp_src_en	= { 0x0768, 9, 9, 0, 1 },
+			.rdm_pdwn_en	= { 0x0768, 10, 10, 0, 1 },
+			.vdm_src_en	= { 0x0768, 12, 12, 0, 1 },
+			.vdp_src_en	= { 0x0768, 11, 11, 0, 1 },
+		},
+	},
+	{
+		.reg = 0x800,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0x0808, 4, 4, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x800, 15, 0, 0, 0x1d1 },
+				.ls_det_en	= { 0x0684, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0694, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x06a4, 0, 0, 0, 1 }
+			},
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x804, 15, 0, 0, 0x1d1 },
+				.ls_det_en	= { 0x0684, 1, 1, 0, 1 },
+				.ls_det_st	= { 0x0694, 1, 1, 0, 1 },
+				.ls_det_clr	= { 0x06a4, 1, 1, 0, 1 }
+			}
+		},
+	},
+	{ /* sentinel */ }
+};
+
 static const struct rockchip_usb2phy_cfg rk3328_phy_cfgs[] = {
 	{
 		.reg = 0x100,
@@ -1263,6 +1328,7 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
 };
 
 static const struct of_device_id rockchip_usb2phy_dt_match[] = {
+	{ .compatible = "rockchip,rk3228-usb2phy", .data = &rk3228_phy_cfgs },
 	{ .compatible = "rockchip,rk3328-usb2phy", .data = &rk3328_phy_cfgs },
 	{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
 	{ .compatible = "rockchip,rk3399-usb2phy", .data = &rk3399_phy_cfgs },

drivers/phy/samsung/Kconfig

+#
+# Phy drivers for Samsung platforms
+#
+config PHY_EXYNOS_DP_VIDEO
+	tristate "EXYNOS SoC series Display Port PHY driver"
+	depends on OF
+	depends on ARCH_EXYNOS || COMPILE_TEST
+	default ARCH_EXYNOS
+	select GENERIC_PHY
+	help
+	  Support for Display Port PHY found on Samsung EXYNOS SoCs.
+
+config PHY_EXYNOS_MIPI_VIDEO
+	tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
+	depends on HAS_IOMEM
+	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
+	select GENERIC_PHY
+	default y if ARCH_S5PV210 || ARCH_EXYNOS
+	help
+	  Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
+	  and EXYNOS SoCs.
+
+config PHY_EXYNOS_PCIE
+	bool "Exynos PCIe PHY driver"
+	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable PCIe PHY support for Exynos SoC series.
+	  This driver provides PHY interface for Exynos PCIe controller.
+
+config PHY_SAMSUNG_USB2
+	tristate "Samsung USB 2.0 PHY driver"
+	depends on HAS_IOMEM
+	depends on USB_EHCI_EXYNOS || USB_OHCI_EXYNOS || USB_DWC2
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default ARCH_EXYNOS
+	help
+	  Enable this to support the Samsung USB 2.0 PHY driver for Samsung
+	  SoCs. This driver provides the interface for USB 2.0 PHY. Support
+	  for particular PHYs will be enabled based on the SoC type in addition
+	  to this driver.
+
+config PHY_EXYNOS4210_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default CPU_EXYNOS4210
+
+config PHY_EXYNOS4X12_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS3250 || SOC_EXYNOS4212 || SOC_EXYNOS4412
+
+config PHY_EXYNOS5250_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS5250 || SOC_EXYNOS5420
+
+config PHY_S5PV210_USB2
+	bool "Support for S5PV210"
+	depends on PHY_SAMSUNG_USB2
+	depends on ARCH_S5PV210
+	help
+	  Enable USB PHY support for S5PV210. This option requires that Samsung
+	  USB 2.0 PHY driver is enabled and means that support for this
+	  particular SoC is compiled in the driver. In case of S5PV210 two phys
+	  are available - device and host.
+
+config PHY_EXYNOS5_USBDRD
+	tristate "Exynos5 SoC series USB DRD PHY driver"
+	depends on ARCH_EXYNOS && OF
+	depends on HAS_IOMEM
+	depends on USB_DWC3_EXYNOS
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default y
+	help
+	  Enable USB DRD PHY support for Exynos 5 SoC series.
+	  This driver provides PHY interface for USB 3.0 DRD controller
+	  present on Exynos5 SoC series.
+
+config PHY_EXYNOS5250_SATA
+	tristate "Exynos5250 Sata SerDes/PHY driver"
+	depends on SOC_EXYNOS5250
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+	select I2C
+	select I2C_S3C2410
+	select MFD_SYSCON
+	help
+	  Enable this to support SATA SerDes/Phy found on Samsung's
+	  Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
+	  SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
+	  port to accept one SATA device.

drivers/phy/samsung/Makefile

+obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
+obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
+obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
+obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
+phy-exynos-usb2-y			+= phy-samsung-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
+obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
+obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o

drivers/phy/st/Kconfig

+#
+# Phy drivers for STMicro platforms
+#
+config PHY_MIPHY28LP
+	tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407"
+	depends on ARCH_STI
+	select GENERIC_PHY
+	help
+	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
+	  that is part of STMicroelectronics STiH407 SoC.
+
+config PHY_ST_SPEAR1310_MIPHY
+	tristate "ST SPEAR1310-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1310 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
+
+config PHY_ST_SPEAR1340_MIPHY
+	tristate "ST SPEAR1340-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1340 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
+
+config PHY_STIH407_USB
+	tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
+	depends on RESET_CONTROLLER
+	depends on ARCH_STI || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this support to enable the picoPHY device used by USB2
+	  and USB3 controllers on STMicroelectronics STiH407 SoC families.

drivers/phy/st/Makefile

+obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
+obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
+obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
+obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o

drivers/phy/ti/Kconfig

+#
+# Phy drivers for TI platforms
+#
+config PHY_DA8XX_USB
+	tristate "TI DA8xx USB PHY Driver"
+	depends on ARCH_DAVINCI_DA8XX
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the USB PHY on DA8xx SoCs.
+
+	  This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
+
+config PHY_DM816X_USB
+	tristate "TI dm816x USB PHY driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this for dm816x USB to work.
+
+config OMAP_CONTROL_PHY
+	tristate "OMAP CONTROL PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	help
+	  Enable this to add support for the PHY part present in the control
+	  module. This driver has API to power on the USB2 PHY and to write to
+	  the mailbox. The mailbox is present only in omap4 and the register to
+	  power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
+	  additional register to power on USB3 PHY/SATA PHY/PCIE PHY
+	  (PIPE3 PHY).
+
+config OMAP_USB2
+	tristate "OMAP USB2 PHY Driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the transceiver that is part of SOC. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  The USB OTG controller communicates with the comparator using this
+	  driver.
+
+config TI_PIPE3
+	tristate "TI PIPE3 PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	select GENERIC_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  This driver interacts with the "OMAP Control PHY Driver" to power
+	  on/off the PHY.
+
+config PHY_TUSB1210
+	tristate "TI TUSB1210 ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for TI TUSB1210 USB ULPI PHY.
+
+config TWL4030_USB
+	tristate "TWL4030 USB Transceiver Driver"
+	depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
+	depends on USB_SUPPORT
+	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this to support the USB OTG transceiver on TWL4030
+	  family chips (including the TWL5030 and TPS659x0 devices).
+	  This transceiver supports high and full speed devices plus,
+	  in host mode, low speed.

drivers/phy/ti/Makefile

+obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
+obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
+obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
+obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
+obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
+obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
+obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o

drivers/phy/phy-tusb1210.c → drivers/phy/ti/phy-tusb1210.c

@@ -11,9 +11,9 @@
  */
 #include <linux/module.h>
 #include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
 #include <linux/gpio/consumer.h>
-
-#include "ulpi_phy.h"
+#include <linux/phy/ulpi_phy.h>
 
 #define TUSB1210_VENDOR_SPECIFIC2		0x80
 #define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT	0
@@ -53,9 +53,43 @@ static int tusb1210_power_off(struct phy *phy)
 	return 0;
 }
 
+static int tusb1210_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+	int ret;
+
+	ret = ulpi_read(tusb->ulpi, ULPI_OTG_CTRL);
+	if (ret < 0)
+		return ret;
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+		ret |= (ULPI_OTG_CTRL_DRVVBUS_EXT
+			| ULPI_OTG_CTRL_ID_PULLUP
+			| ULPI_OTG_CTRL_DP_PULLDOWN
+			| ULPI_OTG_CTRL_DM_PULLDOWN);
+		ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+		ret |= ULPI_OTG_CTRL_DRVVBUS;
+		break;
+	case PHY_MODE_USB_DEVICE:
+		ret &= ~(ULPI_OTG_CTRL_DRVVBUS
+			 | ULPI_OTG_CTRL_DP_PULLDOWN
+			 | ULPI_OTG_CTRL_DM_PULLDOWN);
+		ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+		ret &= ~ULPI_OTG_CTRL_DRVVBUS_EXT;
+		break;
+	default:
+		/* nothing */
+		return 0;
+	}
+
+	return ulpi_write(tusb->ulpi, ULPI_OTG_CTRL, ret);
+}
+
 static const struct phy_ops phy_ops = {
 	.power_on = tusb1210_power_on,
 	.power_off = tusb1210_power_off,
+	.set_mode = tusb1210_set_mode,
 	.owner = THIS_MODULE,
 };
 
@@ -125,7 +159,8 @@ static void tusb1210_remove(struct ulpi *ulpi)
 #define TI_VENDOR_ID 0x0451
 
 static const struct ulpi_device_id tusb1210_ulpi_id[] = {
-	{ TI_VENDOR_ID, 0x1507, },
+	{ TI_VENDOR_ID, 0x1507, },  /* TUSB1210 */
+	{ TI_VENDOR_ID, 0x1508, },  /* TUSB1211 */
 	{ },
 };
 MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id);