Skip to content

L
linux
Commit 2f7d63f9 authored by Mike Frysinger's avatar Mike Frysinger
Browse files
Options

Blackfin: boards: clean up redundant/dead spi resources 

The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant.  So punt
those parts.

Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
parent 9be8631b
Hide whitespace changes
Inline Side-by-side
Showing with 0 additions and 896 deletions
arch/blackfin/mach-bf518/boards/ezbrd.c
View file @ 2f7d63f9
......@@ -187,43 +187,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
#if defined(CONFIG_NET_DSA_KSZ8893M) \
|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
/* SPI SWITCH CHIP */
static struct bfin5xx_spi_chip spi_switch_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -239,21 +212,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
};
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -269,18 +227,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
#if defined(CONFIG_NET_DSA_KSZ8893M) \
|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
......@@ -290,7 +236,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 1,
.platform_data = NULL,
.controller_data = &spi_switch_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -314,7 +259,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
......@@ -324,7 +268,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_wm8731_chip_info,
.mode = SPI_MODE_0,
},
#endif
......@@ -334,7 +277,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -343,7 +285,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......
arch/blackfin/mach-bf518/boards/tcm-bf518.c
View file @ 2f7d63f9
......@@ -138,32 +138,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -179,21 +163,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
};
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -209,18 +178,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
......@@ -239,7 +196,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
......@@ -249,7 +205,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_wm8731_chip_info,
.mode = SPI_MODE_0,
},
#endif
......@@ -259,7 +214,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -268,7 +222,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......
arch/blackfin/mach-bf527/boards/ad7160eval.c
View file @ 2f7d63f9
......@@ -265,29 +265,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -328,7 +311,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
......@@ -347,7 +329,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf527/boards/cm_bf527.c
View file @ 2f7d63f9
......@@ -354,40 +354,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -403,21 +379,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
};
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -433,18 +394,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
......@@ -452,7 +401,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
......@@ -473,7 +421,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
......@@ -483,7 +430,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_wm8731_chip_info,
.mode = SPI_MODE_0,
},
#endif
......@@ -493,7 +439,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf527/boards/ezbrd.c
View file @ 2f7d63f9
......@@ -253,32 +253,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (sst25wf040) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -311,35 +295,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
&& defined(CONFIG_SND_SOC_WM8731_SPI)
static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -355,18 +310,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
......@@ -385,7 +328,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
......@@ -396,7 +338,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_ad7879_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -407,7 +348,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_wm8731_chip_info,
.mode = SPI_MODE_0,
},
#endif
......@@ -417,7 +357,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -426,7 +365,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......
arch/blackfin/mach-bf527/boards/ezkit.c
View file @ 2f7d63f9
......@@ -451,40 +451,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -516,20 +492,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
......@@ -608,13 +570,6 @@ static struct platform_device bfin_tdm = {
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -630,18 +585,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
......@@ -650,7 +593,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836",
.controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -673,7 +615,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
......@@ -684,7 +625,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 3,
.controller_data = &spi_ad7879_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -694,7 +634,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -703,7 +642,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 7,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......
arch/blackfin/mach-bf527/boards/tll6527m.c
View file @ 2f7d63f9
......@@ -314,29 +314,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
/*
* tll6527m V1.0 does not support native spi slave selects
* hence DMA mode will not be useful since the ADC needs
* CS to toggle for each sample and cs_change_per_word
* seems to be removed from spi_bfin5xx.c
*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -359,21 +342,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
|| defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
static struct platform_device bfin_i2s = {
.name = "bfin-i2s",
......@@ -382,24 +350,7 @@ static struct platform_device bfin_i2s = {
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#include <linux/spi/mcp23s08.h>
static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
.chip[0].is_present = true,
......@@ -429,22 +380,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC)
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc",
/* Name of spi_driver for this device */
.max_speed_hz = 10000000,
/* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
/* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
.mode = SPI_MODE_0,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
......@@ -470,7 +405,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
/* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
.controller_data = &spi_ad7879_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -482,7 +416,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
.mode = SPI_CPHA | SPI_CPOL,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -491,7 +424,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -502,7 +434,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
.controller_data = &spi_mcp23s08_sys_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
{
......@@ -511,7 +442,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
.controller_data = &spi_mcp23s08_usr_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......
arch/blackfin/mach-bf533/boards/H8606.c
View file @ 2f7d63f9
......@@ -159,22 +159,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
......@@ -195,24 +179,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 4, /* actual baudrate is SCLK/(2xspeed_hz) */
.bus_num = 1, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 16,
.bus_num = 1,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
......
arch/blackfin/mach-bf533/boards/blackstamp.c
View file @ 2f7d63f9
......@@ -102,21 +102,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -151,7 +142,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 7,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf533/boards/cm_bf533.c
View file @ 2f7d63f9
......@@ -59,29 +59,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
/* SPI ADC chip */
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -99,24 +82,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
......
arch/blackfin/mach-bf533/boards/ezkit.c
View file @ 2f7d63f9
......@@ -210,29 +210,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -250,24 +227,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
......@@ -276,7 +241,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf533/boards/ip0x.c
View file @ 2f7d63f9
......@@ -110,7 +110,6 @@ static struct platform_device dm9000_device2 = {
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* if 1 - block!!! */
.bits_per_word = 8,
};
#endif
......
arch/blackfin/mach-bf533/boards/stamp.c
View file @ 2f7d63f9
......@@ -175,29 +175,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -224,7 +201,6 @@ static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
.pio_interrupt = 0,
};
#endif
......@@ -243,17 +219,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
......@@ -261,7 +226,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -272,7 +236,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
......
arch/blackfin/mach-bf537/boards/cm_bf537e.c
View file @ 2f7d63f9
......@@ -61,29 +61,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -101,24 +84,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
......
arch/blackfin/mach-bf537/boards/cm_bf537u.c
View file @ 2f7d63f9
......@@ -62,29 +62,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -102,24 +85,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
......
arch/blackfin/mach-bf537/boards/dnp5370.c
View file @ 2f7d63f9
......@@ -130,7 +130,6 @@ static struct platform_device asmb_flash_device = {
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* use no dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
......@@ -161,7 +160,6 @@ static struct flash_platform_data bfin_spi_dataflash_data = {
static struct bfin5xx_spi_chip spi_dataflash_chip_info = {
.enable_dma = 0, /* use no dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
......
arch/blackfin/mach-bf537/boards/minotaur.c
View file @ 2f7d63f9
......@@ -159,14 +159,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......
arch/blackfin/mach-bf537/boards/pnav10.c
View file @ 2f7d63f9
......@@ -184,40 +184,16 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -248,18 +224,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
......@@ -267,7 +231,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
......@@ -288,7 +251,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &spi_ad7877_chip_info,
},
#endif
......
arch/blackfin/mach-bf537/boards/stamp.c
View file @ 2f7d63f9
......@@ -536,49 +536,11 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD193X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) \
|| defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
static struct bfin5xx_spi_chip adav801_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
#include <linux/input/ad714x.h>
static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
{
......@@ -688,7 +650,6 @@ static struct ad714x_platform_data ad7142_i2c_platform_data = {
#if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
static struct bfin5xx_spi_chip ad2s90_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
......@@ -700,7 +661,6 @@ static unsigned short ad2s120x_platform_data[] = {
static struct bfin5xx_spi_chip ad2s120x_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
......@@ -717,14 +677,12 @@ static unsigned short ad2s1210_platform_data[] = {
static struct bfin5xx_spi_chip ad2s1210_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_AD7314) || defined(CONFIG_AD7314_MODULE)
static struct bfin5xx_spi_chip ad7314_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
......@@ -738,7 +696,6 @@ static unsigned short ad7816_platform_data[] = {
static struct bfin5xx_spi_chip ad7816_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -752,7 +709,6 @@ static unsigned long adt7310_platform_data[3] = {
static struct bfin5xx_spi_chip adt7310_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -761,11 +717,6 @@ static unsigned short ad7298_platform_data[] = {
GPIO_PF7, /* busy_pin */
0,
};
static struct bfin5xx_spi_chip ad7298_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
......@@ -776,7 +727,6 @@ static unsigned long adt7316_spi_data[2] = {
static struct bfin5xx_spi_chip adt7316_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -803,18 +753,12 @@ static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
.pio_interrupt = 0,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
#include <linux/spi/ad7877.h>
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -886,39 +830,13 @@ static const struct adxl34x_platform_data adxl34x_info = {
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
.enable_dma = 1,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
.bits_per_word = 16,
};
#include <linux/spi/adf702x.h>
#define TXREG 0x0160A470
static const u32 adf7021_regs[] = {
......@@ -962,10 +880,6 @@ static inline void adf702x_mac_init(void) {}
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
#include <linux/spi/ads7846.h>
static struct bfin5xx_spi_chip ad7873_spi_chip_info = {
.bits_per_word = 8,
};
static int ads7873_get_pendown_state(void)
{
return gpio_get_value(GPIO_PF6);
......@@ -1012,21 +926,12 @@ static struct flash_platform_data bfin_spi_dataflash_data = {
/* DataFlash chip */
static struct bfin5xx_spi_chip data_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_AD7476) || defined(CONFIG_AD7476_MODULE)
static struct bfin5xx_spi_chip spi_ad7476_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
......@@ -1056,17 +961,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) \
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
......@@ -1076,7 +970,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -1087,7 +980,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &ad1938_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -1098,7 +990,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &adav801_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -1112,7 +1003,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.chip_select = 5,
.mode = SPI_MODE_3,
.platform_data = &ad7147_spi_platform_data,
.controller_data = &ad7147_spi_chip_info,
},
#endif
......@@ -1191,7 +1081,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4, /* CS, change it for your board */
.platform_data = ad7298_platform_data,
.controller_data = &ad7298_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -1228,7 +1117,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
......@@ -1239,7 +1127,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7879_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -1249,7 +1136,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
......@@ -1258,7 +1144,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -1281,7 +1166,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_adxl34x_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -1291,7 +1175,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 16000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = GPIO_PF10 + MAX_CTRL_CS, /* GPIO controlled SSEL */
.controller_data = &adf7021_spi_chip_info,
.platform_data = &adf7021_platform_data,
.mode = SPI_MODE_0,
},
......@@ -1303,7 +1186,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.irq = IRQ_PF6,
.chip_select = GPIO_PF10 + MAX_CTRL_CS, /* GPIO controlled SSEL */
.controller_data = &ad7873_spi_chip_info,
.platform_data = &ad7873_pdata,
.mode = SPI_MODE_0,
},
......
arch/blackfin/mach-bf537/boards/tcm_bf537.c
View file @ 2f7d63f9
......@@ -62,29 +62,12 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -102,24 +85,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
......
arch/blackfin/mach-bf538/boards/ezkit.c
View file @ 2f7d63f9
......@@ -502,7 +502,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
......@@ -523,13 +522,6 @@ static const struct ad7879_platform_data bfin_ad7879_ts_info = {
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
#include <asm/bfin-lq035q1.h>
......@@ -559,20 +551,6 @@ static struct platform_device bfin_lq035q1_device = {
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bf538_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -595,7 +573,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7879_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -605,7 +582,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &lq035q1_spi_chip_info,
.mode = SPI_CPHA | SPI_CPOL,
},
#endif
......@@ -615,7 +591,6 @@ static struct spi_board_info bf538_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf548/boards/cm_bf548.c
View file @ 2f7d63f9
......@@ -861,16 +861,10 @@ static struct flash_platform_data bfin_spi_flash_data = {
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -886,13 +880,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
static struct spi_board_info bf54x_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -915,7 +902,6 @@ static struct spi_board_info bf54x_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
......@@ -924,7 +910,6 @@ static struct spi_board_info bf54x_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
arch/blackfin/mach-bf548/boards/ezkit.c
View file @ 2f7d63f9
......@@ -1018,24 +1018,10 @@ static struct flash_platform_data bfin_spi_flash_data = {
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
.model = 7877,
.vref_delay_usecs = 50, /* internal, no capacitor */
......@@ -1051,20 +1037,6 @@ static const struct ad7877_platform_data bfin_ad7877_ts_info = {
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
......@@ -1086,7 +1058,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 1,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
......@@ -1097,7 +1068,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 2,
.controller_data = &spi_ad7877_chip_info,
},
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
......@@ -1106,7 +1076,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
......@@ -1117,7 +1086,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 1,
.chip_select = 2,
.controller_data = &spi_adxl34x_chip_info,
.mode = SPI_MODE_3,
},
#endif
......
arch/blackfin/mach-bf561/boards/acvilon.c
View file @ 2f7d63f9
......@@ -364,14 +364,6 @@ static struct flash_platform_data bfin_spi_dataflash_data = {
/* DataFlash chip */
static struct bfin5xx_spi_chip data_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip */
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -420,7 +412,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 3,
.controller_data = &spidev_chip_info,
},
#endif
#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
......
arch/blackfin/mach-bf561/boards/cm_bf561.c
View file @ 2f7d63f9
......@@ -60,29 +60,6 @@ static struct flash_platform_data bfin_spi_flash_data = {
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
/* SPI ADC chip */
static struct bfin5xx_spi_chip spi_adc_chip_info = {
.enable_dma = 1, /* use dma transfer with this chip*/
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
......@@ -100,24 +77,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
{
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 1, /* Framework chip select. */
.platform_data = NULL, /* No spi_driver specific config */
.controller_data = &spi_adc_chip_info,
},
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
{
.modalias = "ad183x",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 4,
.controller_data = &ad1836_spi_chip_info,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
......@@ -126,7 +91,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......
arch/blackfin/mach-bf561/boards/ezkit.c
View file @ 2f7d63f9
......@@ -286,21 +286,6 @@ static struct platform_device ezkit_flash_device = {
};
#endif
#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
static struct bfin5xx_spi_chip spidev_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
};
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
......@@ -348,7 +333,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.bus_num = 0,
.chip_select = 4,
.platform_data = "ad1836", /* only includes chip name for the moment */
.controller_data = &ad1836_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
......@@ -358,7 +342,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 1,
.controller_data = &spidev_chip_info,
},
#endif
};
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7