Commit 3faa1ffb authored by Hans de Goede's avatar Hans de Goede Committed by Mark M. Hoffman

hwmon: Add support for newer uGuru's

This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: default avatarHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: default avatarMark M. Hoffman <mhoffman@lightlink.com>
parent aba5073d
......@@ -2,7 +2,7 @@ Kernel driver abituguru
=======================
Supported chips:
* Abit uGuru revision 1-3 (Hardware Monitor part only)
* Abit uGuru revision 1 & 2 (Hardware Monitor part only)
Prefix: 'abituguru'
Addresses scanned: ISA 0x0E0
Datasheet: Not available, this driver is based on reverse engineering.
......@@ -20,8 +20,8 @@ Supported chips:
uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8)
uGuru 4.xxxxx? (AT8 32X) (2)
uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
AW9D-MAX) (2)
1) For revisions 2 and 3 uGuru's the driver can autodetect the
sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
this doesnot always work. For these uGuru's the autodection can
......@@ -30,8 +30,9 @@ Supported chips:
bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
You may also need to specify the fan_sensors option for these boards
fan_sensors=5
2) The current version of the abituguru driver is known to NOT work
on these Motherboards
2) There is a seperate abituguru3 driver for these motherboards,
the abituguru (without the 3 !) driver will not work on these
motherboards (and visa versa)!
Authors:
Hans de Goede <j.w.r.degoede@hhs.nl>,
......@@ -43,8 +44,10 @@ Module Parameters
-----------------
* force: bool Force detection. Note this parameter only causes the
detection to be skipped, if the uGuru can't be read
the module initialization (insmod) will still fail.
detection to be skipped, and thus the insmod to
succeed. If the uGuru can't be read the actual hwmon
driver will not load and thus no hwmon device will get
registered.
* bank1_types: int[] Bank1 sensortype autodetection override:
-1 autodetect (default)
0 volt sensor
......@@ -69,13 +72,15 @@ dmesg | grep abituguru
Description
-----------
This driver supports the hardware monitoring features of the Abit uGuru chip
found on Abit uGuru featuring motherboards (most modern Abit motherboards).
This driver supports the hardware monitoring features of the first and
second revision of the Abit uGuru chip found on Abit uGuru featuring
motherboards (most modern Abit motherboards).
The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit
claiming it is "a new microprocessor designed by the ABIT Engineers").
Unfortunatly this doesn't help since the W83L950D is a generic
microcontroller with a custom Abit application running on it.
The first and second revision of the uGuru chip in reality is a Winbond
W83L950D in disguise (despite Abit claiming it is "a new microprocessor
designed by the ABIT Engineers"). Unfortunatly this doesn't help since the
W83L950D is a generic microcontroller with a custom Abit application running
on it.
Despite Abit not releasing any information regarding the uGuru, Olle
Sandberg <ollebull@gmail.com> has managed to reverse engineer the sensor part
......
Kernel driver abituguru3
========================
Supported chips:
* Abit uGuru revision 3 (Hardware Monitor part, reading only)
Prefix: 'abituguru3'
Addresses scanned: ISA 0x0E0
Datasheet: Not available, this driver is based on reverse engineering.
Note:
The uGuru is a microcontroller with onboard firmware which programs
it to behave as a hwmon IC. There are many different revisions of the
firmware and thus effectivly many different revisions of the uGuru.
Below is an incomplete list with which revisions are used for which
Motherboards:
uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7)
uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO)
uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X,
AW9D-MAX)
The abituguru3 driver is only for revison 3.0.x.x motherboards,
this driver will not work on older motherboards. For older
motherboards use the abituguru (without the 3 !) driver.
Authors:
Hans de Goede <j.w.r.degoede@hhs.nl>,
(Initial reverse engineering done by Louis Kruger)
Module Parameters
-----------------
* force: bool Force detection. Note this parameter only causes the
detection to be skipped, and thus the insmod to
succeed. If the uGuru can't be read the actual hwmon
driver will not load and thus no hwmon device will get
registered.
* verbose: bool Should the driver be verbose?
0/off/false normal output
1/on/true + verbose error reporting (default)
Default: 1 (the driver is still in the testing phase)
Description
-----------
This driver supports the hardware monitoring features of the third revision of
the Abit uGuru chip, found on recent Abit uGuru featuring motherboards.
The 3rd revision of the uGuru chip in reality is a Winbond W83L951G.
Unfortunatly this doesn't help since the W83L951G is a generic microcontroller
with a custom Abit application running on it.
Despite Abit not releasing any information regarding the uGuru revision 3,
Louis Kruger has managed to reverse engineer the sensor part of the uGuru.
Without his work this driver would not have been possible.
Known Issues
------------
The voltage and frequency control parts of the Abit uGuru are not supported,
neither is writing any of the sensor settings and writing / reading the
fanspeed control registers (FanEQ)
If you encounter any problems please mail me <j.w.r.degoede@hhs.nl> and
include the output of: "dmesg | grep abituguru"
......@@ -29,17 +29,34 @@ config HWMON_VID
default n
config SENSORS_ABITUGURU
tristate "Abit uGuru"
tristate "Abit uGuru (rev 1 & 2)"
depends on EXPERIMENTAL
help
If you say yes here you get support for the Abit uGuru chips
sensor part. The voltage and frequency control parts of the Abit
uGuru are not supported. The Abit uGuru chip can be found on Abit
uGuru featuring motherboards (most modern Abit motherboards).
If you say yes here you get support for the sensor part of the first
and second revision of the Abit uGuru chip. The voltage and frequency
control parts of the Abit uGuru are not supported. The Abit uGuru
chip can be found on Abit uGuru featuring motherboards (most modern
Abit motherboards from before end 2005). For more info and a list
of which motherboards have which revision see
Documentation/hwmon/abituguru
This driver can also be built as a module. If so, the module
will be called abituguru.
config SENSORS_ABITUGURU3
tristate "Abit uGuru (rev 3)"
depends on HWMON && EXPERIMENTAL
help
If you say yes here you get support for the sensor part of the
third revision of the Abit uGuru chip. Only reading the sensors
and their settings is supported. The third revision of the Abit
uGuru chip can be found on recent Abit motherboards (since end
2005). For more info and a list of which motherboards have which
revision see Documentation/hwmon/abituguru3
This driver can also be built as a module. If so, the module
will be called abituguru3.
config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
depends on I2C && EXPERIMENTAL
......
......@@ -14,6 +14,7 @@ obj-$(CONFIG_SENSORS_W83781D) += w83781d.o
obj-$(CONFIG_SENSORS_W83791D) += w83791d.o
obj-$(CONFIG_SENSORS_ABITUGURU) += abituguru.o
obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
obj-$(CONFIG_SENSORS_AD7418) += ad7418.o
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
......
......@@ -16,9 +16,9 @@
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
This driver supports the sensor part of the custom Abit uGuru chip found
on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM /
etc voltage & frequency control is not supported!
This driver supports the sensor part of the first and second revision of
the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
of lack of specs the CPU/RAM voltage & frequency control is not supported!
*/
#include <linux/module.h>
#include <linux/sched.h>
......
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment