Merge branch 'next-s3c' of git://aeryn.fluff.org.uk/bjdooks/linux into devel

Documentation/kernel-parameters.txt

@@ -1362,6 +1362,27 @@ and is between 256 and 4096 characters. It is defined in the file
 	min_addr=nn[KMG]	[KNL,BOOT,ia64] All physical memory below this
 			physical address is ignored.
 
+	mini2440=	[ARM,HW,KNL]
+			Format:[0..2][b][c][t]
+			Default: "0tb"
+			MINI2440 configuration specification:
+			0 - The attached screen is the 3.5" TFT
+			1 - The attached screen is the 7" TFT
+			2 - The VGA Shield is attached (1024x768)
+			Leaving out the screen size parameter will not load
+			the TFT driver, and the framebuffer will be left
+			unconfigured.
+			b - Enable backlight. The TFT backlight pin will be
+			linked to the kernel VESA blanking code and a GPIO
+			LED. This parameter is not necessary when using the
+			VGA shield.
+			c - Enable the s3c camera interface.
+			t - Reserved for enabling touchscreen support. The
+			touchscreen support is not enabled in the mainstream
+			kernel as of 2.6.30, a preliminary port can be found
+			in the "bleeding edge" mini2440 support kernel at
+			http://repo.or.cz/w/linux-2.6/mini2440.git
+
 	mminit_loglevel=
 			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
 			parameter allows control of the logging verbosity for

MAINTAINERS

@@ -788,6 +788,13 @@ P:	Michael Petchkovsky
 M:	mkpetch@internode.on.net
 S:	Maintained
 
+ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
+P:	Nelson Castillo
+M:	arhuaco@freaks-unidos.net
+L:	openmoko-kernel@lists.openmoko.org (subscribers-only)
+W:	http://wiki.openmoko.org/wiki/Neo_FreeRunner
+S:	Supported
+
 ARM/TOSA MACHINE SUPPORT
 P:	Dmitry Eremin-Solenikov
 M:	dbaryshkov@gmail.com

arch/arm/Kconfig

@@ -1241,7 +1241,7 @@ endmenu
 
 menu "CPU Power Management"
 
-if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA)
+if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX)
 
 source "drivers/cpufreq/Kconfig"
 
@@ -1272,6 +1272,10 @@ config CPU_FREQ_PXA
 	default y
 	select CPU_FREQ_DEFAULT_GOV_USERSPACE
 
+config CPU_FREQ_S3C64XX
+	bool "CPUfreq support for Samsung S3C64XX CPUs"
+	depends on CPU_FREQ && CPU_S3C6410
+
 endif
 
 source "drivers/cpuidle/Kconfig"

arch/arm/common/vic.c

@@ -229,14 +229,18 @@ static int vic_set_wake(unsigned int irq, unsigned int on)
 {
 	struct vic_device *v = vic_from_irq(irq);
 	unsigned int off = irq & 31;
+	u32 bit = 1 << off;
 
 	if (!v)
 		return -EINVAL;
 
+	if (!(bit & v->resume_sources))
+		return -EINVAL;
+
 	if (on)
-		v->resume_irqs |= 1 << off;
+		v->resume_irqs |= bit;
 	else
-		v->resume_irqs &= ~(1 << off);
+		v->resume_irqs &= ~bit;
 
 	return 0;
 }

arch/arm/mach-s3c2410/usb-simtec.c

@@ -22,7 +22,6 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/device.h>
-#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>

arch/arm/mach-s3c2440/Kconfig

@@ -84,5 +84,15 @@ config MACH_AT2440EVB
 	help
 	  Say Y here if you are using the AT2440EVB development board
 
+config MACH_MINI2440
+	bool "MINI2440 development board"
+	select CPU_S3C2440
+	select EEPROM_AT24
+	select LEDS_TRIGGER_BACKLIGHT
+	select SND_S3C24XX_SOC_S3C24XX_UDA134X
+	help
+	  Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
+	  available via various sources. It can come with a 3.5" or 7" touch LCD.
+
 endmenu
 

arch/arm/mach-s3c2440/Makefile

@@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715)	+= mach-rx3715.o
 obj-$(CONFIG_ARCH_S3C2440)	+= mach-smdk2440.o
 obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
 obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
+obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o

arch/arm/mach-s3c2442/Kconfig

@@ -24,6 +24,18 @@ config SMDK2440_CPU2442
 	depends on ARCH_S3C2440
 	select CPU_S3C2442
 
+config MACH_NEO1973_GTA02
+	bool "Openmoko GTA02 / Freerunner phone"
+	select CPU_S3C2442
+	select MFD_PCF50633
+	select PCF50633_GPIO
+	select I2C
+	select POWER_SUPPLY
+	select MACH_NEO1973
+	select S3C2410_PWM
+	help
+	   Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone
+
 
 endmenu
 

arch/arm/mach-s3c2442/Makefile

@@ -12,5 +12,7 @@ obj-				:=
 obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
 obj-$(CONFIG_CPU_S3C2442)	+= clock.o
 
+obj-$(CONFIG_MACH_NEO1973_GTA02) += mach-gta02.o
+
 # Machine support
 

arch/arm/mach-s3c2442/include/mach/gta02.h

+#ifndef _GTA02_H
+#define _GTA02_H
+
+#include <mach/regs-gpio.h>
+
+/* Different hardware revisions, passed in ATAG_REVISION by u-boot */
+#define GTA02v1_SYSTEM_REV	0x00000310
+#define GTA02v2_SYSTEM_REV	0x00000320
+#define GTA02v3_SYSTEM_REV	0x00000330
+#define GTA02v4_SYSTEM_REV	0x00000340
+#define GTA02v5_SYSTEM_REV	0x00000350
+/* since A7 is basically same as A6, we use A6 PCB ID */
+#define GTA02v6_SYSTEM_REV	0x00000360
+
+#define GTA02_GPIO_n3DL_GSM	S3C2410_GPA(13)	/* v1 + v2 + v3 only */
+
+#define GTA02_GPIO_PWR_LED1	S3C2410_GPB(0)
+#define GTA02_GPIO_PWR_LED2	S3C2410_GPB(1)
+#define GTA02_GPIO_AUX_LED	S3C2410_GPB(2)
+#define GTA02_GPIO_VIBRATOR_ON	S3C2410_GPB(3)
+#define GTA02_GPIO_MODEM_RST	S3C2410_GPB(5)
+#define GTA02_GPIO_BT_EN	S3C2410_GPB(6)
+#define GTA02_GPIO_MODEM_ON	S3C2410_GPB(7)
+#define GTA02_GPIO_EXTINT8	S3C2410_GPB(8)
+#define GTA02_GPIO_USB_PULLUP	S3C2410_GPB(9)
+
+#define GTA02_GPIO_PIO5		S3C2410_GPC(5)	/* v3 + v4 only */
+
+#define GTA02v3_GPIO_nG1_CS	S3C2410_GPD(12)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nG2_CS	S3C2410_GPD(13)	/* v3 + v4 only */
+#define GTA02v5_GPIO_HDQ	S3C2410_GPD(14)   /* v5 + */
+
+#define GTA02_GPIO_nG1_INT	S3C2410_GPF(0)
+#define GTA02_GPIO_IO1		S3C2410_GPF(1)
+#define GTA02_GPIO_PIO_2	S3C2410_GPF(2)	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_JACK_INSERT	S3C2410_GPF(4)
+#define GTA02_GPIO_WLAN_GPIO1	S3C2410_GPF(5)	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_AUX_KEY	S3C2410_GPF(6)
+#define GTA02_GPIO_HOLD_KEY	S3C2410_GPF(7)
+
+#define GTA02_GPIO_3D_IRQ	S3C2410_GPG(4)
+#define GTA02v2_GPIO_nG2_INT	S3C2410_GPG(8)	/* v2 + v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_OC	S3C2410_GPG(9)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_FLT	S3C2410_GPG(10)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nGSM_OC	S3C2410_GPG(11)	/* v3 + v4 only */
+
+#define GTA02_GPIO_AMP_SHUT	S3C2440_GPJ1	/* v2 + v3 + v4 only */
+#define GTA02v1_GPIO_WLAN_GPIO10	S3C2440_GPJ2
+#define GTA02_GPIO_HP_IN	S3C2440_GPJ2	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_INT0		S3C2440_GPJ3	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_nGSM_EN	S3C2440_GPJ4
+#define GTA02_GPIO_3D_RESET	S3C2440_GPJ5
+#define GTA02_GPIO_nDL_GSM	S3C2440_GPJ6	/* v4 + v5 only */
+#define GTA02_GPIO_WLAN_GPIO0	S3C2440_GPJ7
+#define GTA02v1_GPIO_BAT_ID	S3C2440_GPJ8
+#define GTA02_GPIO_KEEPACT	S3C2440_GPJ8
+#define GTA02v1_GPIO_HP_IN	S3C2440_GPJ10
+#define GTA02_CHIP_PWD		S3C2440_GPJ11	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_nWLAN_RESET	S3C2440_GPJ12	/* v2 + v3 + v4 only */
+
+#define GTA02_IRQ_GSENSOR_1	IRQ_EINT0
+#define GTA02_IRQ_MODEM		IRQ_EINT1
+#define GTA02_IRQ_PIO_2		IRQ_EINT2	/* v2 + v3 + v4 only */
+#define GTA02_IRQ_nJACK_INSERT	IRQ_EINT4
+#define GTA02_IRQ_WLAN_GPIO1	IRQ_EINT5
+#define GTA02_IRQ_AUX		IRQ_EINT6
+#define GTA02_IRQ_nHOLD		IRQ_EINT7
+#define GTA02_IRQ_PCF50633	IRQ_EINT9
+#define GTA02_IRQ_3D		IRQ_EINT12
+#define GTA02_IRQ_GSENSOR_2	IRQ_EINT16	/* v2 + v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_OC	IRQ_EINT17	/* v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_FLT	IRQ_EINT18	/* v3 + v4 only */
+#define GTA02v3_IRQ_nGSM_OC	IRQ_EINT19	/* v3 + v4 only */
+
+/* returns 00 000 on GTA02 A5 and earlier, A6 returns 01 001 */
+#define GTA02_PCB_ID1_0		S3C2410_GPC(13)
+#define GTA02_PCB_ID1_1		S3C2410_GPC(15)
+#define GTA02_PCB_ID1_2		S3C2410_GPD(0)
+#define GTA02_PCB_ID2_0		S3C2410_GPD(3)
+#define GTA02_PCB_ID2_1		S3C2410_GPD(4)
+
+int gta02_get_pcb_revision(void);
+
+#endif /* _GTA02_H */

arch/arm/plat-s3c/Makefile

@@ -34,6 +34,7 @@ obj-$(CONFIG_S3C_DEV_HSMMC)	+= dev-hsmmc.o
 obj-$(CONFIG_S3C_DEV_HSMMC1)	+= dev-hsmmc1.o
 obj-y				+= dev-i2c0.o
 obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
+obj-$(CONFIG_SND_S3C24XX_SOC)	+= dev-audio.o
 obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
 obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
 obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o

arch/arm/plat-s3c/dev-audio.c

+/* linux/arch/arm/plat-s3c/dev-audio.c
+ *
+ * Copyright 2009 Wolfson Microelectronics
+ *      Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+
+static struct resource s3c64xx_iis0_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IIS0,
+		.end   = S3C64XX_PA_IIS0 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iis0 = {
+	.name		  = "s3c64xx-iis",
+	.id		  = 0,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iis0_resource),
+	.resource	  = s3c64xx_iis0_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis0);
+
+static struct resource s3c64xx_iis1_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IIS1,
+		.end   = S3C64XX_PA_IIS1 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iis1 = {
+	.name		  = "s3c64xx-iis",
+	.id		  = 1,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iis1_resource),
+	.resource	  = s3c64xx_iis1_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis1);
+
+static struct resource s3c64xx_iisv4_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IISV4,
+		.end   = S3C64XX_PA_IISV4 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iisv4 = {
+	.name		  = "s3c64xx-iis-v4",
+	.id		  = -1,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iisv4_resource),
+	.resource	  = s3c64xx_iisv4_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iisv4);

arch/arm/plat-s3c/include/plat/devs.h

@@ -24,13 +24,16 @@ extern struct platform_device *s3c24xx_uart_src[];
 
 extern struct platform_device s3c_device_timer[];
 
+extern struct platform_device s3c64xx_device_iis0;
+extern struct platform_device s3c64xx_device_iis1;
+extern struct platform_device s3c64xx_device_iisv4;
+
 extern struct platform_device s3c_device_fb;
 extern struct platform_device s3c_device_usb;
 extern struct platform_device s3c_device_lcd;
 extern struct platform_device s3c_device_wdt;
 extern struct platform_device s3c_device_i2c0;
 extern struct platform_device s3c_device_i2c1;
-extern struct platform_device s3c_device_iis;
 extern struct platform_device s3c_device_rtc;
 extern struct platform_device s3c_device_adc;
 extern struct platform_device s3c_device_sdi;

arch/arm/plat-s3c64xx/Makefile

@@ -23,6 +23,7 @@ obj-y				+= gpiolib.o
 
 obj-$(CONFIG_CPU_S3C6400_INIT)	+= s3c6400-init.o
 obj-$(CONFIG_CPU_S3C6400_CLOCK)	+= s3c6400-clock.o
+obj-$(CONFIG_CPU_FREQ_S3C64XX)  += cpufreq.o
 
 # PM support
 

arch/arm/plat-s3c64xx/cpufreq.c

+/* linux/arch/arm/plat-s3c64xx/cpufreq.c
+ *
+ * Copyright 2009 Wolfson Microelectronics plc
+ *
+ * S3C64xx CPUfreq Support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/regulator/consumer.h>
+
+static struct clk *armclk;
+static struct regulator *vddarm;
+
+#ifdef CONFIG_CPU_S3C6410
+struct s3c64xx_dvfs {
+	unsigned int vddarm_min;
+	unsigned int vddarm_max;
+};
+
+static struct s3c64xx_dvfs s3c64xx_dvfs_table[] = {
+	[0] = { 1000000, 1000000 },
+	[1] = { 1000000, 1050000 },
+	[2] = { 1050000, 1100000 },
+	[3] = { 1050000, 1150000 },
+	[4] = { 1250000, 1350000 },
+};
+
+static struct cpufreq_frequency_table s3c64xx_freq_table[] = {
+	{ 0,  66000 },
+	{ 0, 133000 },
+	{ 1, 222000 },
+	{ 1, 266000 },
+	{ 2, 333000 },
+	{ 2, 400000 },
+	{ 3, 532000 },
+	{ 3, 533000 },
+	{ 4, 667000 },
+	{ 0, CPUFREQ_TABLE_END },
+};
+#endif
+
+static int s3c64xx_cpufreq_verify_speed(struct cpufreq_policy *policy)
+{
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	return cpufreq_frequency_table_verify(policy, s3c64xx_freq_table);
+}
+
+static unsigned int s3c64xx_cpufreq_get_speed(unsigned int cpu)
+{
+	if (cpu != 0)
+		return 0;
+
+	return clk_get_rate(armclk) / 1000;
+}
+
+static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy,
+				      unsigned int target_freq,
+				      unsigned int relation)
+{
+	int ret;
+	unsigned int i;
+	struct cpufreq_freqs freqs;
+	struct s3c64xx_dvfs *dvfs;
+
+	ret = cpufreq_frequency_table_target(policy, s3c64xx_freq_table,
+					     target_freq, relation, &i);
+	if (ret != 0)
+		return ret;
+
+	freqs.cpu = 0;
+	freqs.old = clk_get_rate(armclk) / 1000;
+	freqs.new = s3c64xx_freq_table[i].frequency;
+	freqs.flags = 0;
+	dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[i].index];
+
+	if (freqs.old == freqs.new)
+		return 0;
+
+	pr_debug("cpufreq: Transition %d-%dkHz\n", freqs.old, freqs.new);
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+
+#ifdef CONFIG_REGULATOR
+	if (vddarm && freqs.new > freqs.old) {
+		ret = regulator_set_voltage(vddarm,
+					    dvfs->vddarm_min,
+					    dvfs->vddarm_max);
+		if (ret != 0) {
+			pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+			       freqs.new, ret);
+			goto err;
+		}
+	}
+#endif
+
+	ret = clk_set_rate(armclk, freqs.new * 1000);
+	if (ret < 0) {
+		pr_err("cpufreq: Failed to set rate %dkHz: %d\n",
+		       freqs.new, ret);
+		goto err;
+	}
+
+#ifdef CONFIG_REGULATOR
+	if (vddarm && freqs.new < freqs.old) {
+		ret = regulator_set_voltage(vddarm,
+					    dvfs->vddarm_min,
+					    dvfs->vddarm_max);
+		if (ret != 0) {
+			pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+			       freqs.new, ret);
+			goto err_clk;
+		}
+	}
+#endif
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	pr_debug("cpufreq: Set actual frequency %lukHz\n",
+		 clk_get_rate(armclk) / 1000);
+
+	return 0;
+
+err_clk:
+	if (clk_set_rate(armclk, freqs.old * 1000) < 0)
+		pr_err("Failed to restore original clock rate\n");
+err:
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	return ret;
+}
+
+#ifdef CONFIG_REGULATOR
+static void __init s3c64xx_cpufreq_constrain_voltages(void)
+{
+	int count, v, i, found;
+	struct cpufreq_frequency_table *freq;
+	struct s3c64xx_dvfs *dvfs;
+
+	count = regulator_count_voltages(vddarm);
+	if (count < 0) {
+		pr_err("cpufreq: Unable to check supported voltages\n");
+		return;
+	}
+
+	freq = s3c64xx_freq_table;
+	while (freq->frequency != CPUFREQ_TABLE_END) {
+		if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+			continue;
+
+		dvfs = &s3c64xx_dvfs_table[freq->index];
+		found = 0;
+
+		for (i = 0; i < count; i++) {
+			v = regulator_list_voltage(vddarm, i);
+			if (v >= dvfs->vddarm_min && v <= dvfs->vddarm_max)
+				found = 1;
+		}
+
+		if (!found) {
+			pr_debug("cpufreq: %dkHz unsupported by regulator\n",
+				 freq->frequency);
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+		}
+
+		freq++;
+	}
+}
+#endif
+
+static int __init s3c64xx_cpufreq_driver_init(struct cpufreq_policy *policy)
+{
+	int ret;
+	struct cpufreq_frequency_table *freq;
+
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	if (s3c64xx_freq_table == NULL) {
+		pr_err("cpufreq: No frequency information for this CPU\n");
+		return -ENODEV;
+	}
+
+	armclk = clk_get(NULL, "armclk");
+	if (IS_ERR(armclk)) {
+		pr_err("cpufreq: Unable to obtain ARMCLK: %ld\n",
+		       PTR_ERR(armclk));
+		return PTR_ERR(armclk);
+	}
+
+#ifdef CONFIG_REGULATOR
+	vddarm = regulator_get(NULL, "vddarm");
+	if (IS_ERR(vddarm)) {
+		ret = PTR_ERR(vddarm);
+		pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret);
+		pr_err("cpufreq: Only frequency scaling available\n");
+		vddarm = NULL;
+	} else {
+		s3c64xx_cpufreq_constrain_voltages();
+	}
+#endif
+
+	freq = s3c64xx_freq_table;
+	while (freq->frequency != CPUFREQ_TABLE_END) {
+		unsigned long r;
+
+		/* Check for frequencies we can generate */
+		r = clk_round_rate(armclk, freq->frequency * 1000);
+		r /= 1000;
+		if (r != freq->frequency)
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+		/* If we have no regulator then assume startup
+		 * frequency is the maximum we can support. */
+		if (!vddarm && freq->frequency > s3c64xx_cpufreq_get_speed(0))
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+		freq++;
+	}
+
+	policy->cur = clk_get_rate(armclk) / 1000;
+
+	/* Pick a conservative guess in ns: we'll need ~1 I2C/SPI
+	 * write plus clock reprogramming. */
+	policy->cpuinfo.transition_latency = 2 * 1000 * 1000;
+
+	ret = cpufreq_frequency_table_cpuinfo(policy, s3c64xx_freq_table);
+	if (ret != 0) {
+		pr_err("cpufreq: Failed to configure frequency table: %d\n",
+		       ret);
+		regulator_put(vddarm);
+		clk_put(armclk);
+	}
+
+	return ret;
+}
+
+static struct cpufreq_driver s3c64xx_cpufreq_driver = {
+	.owner		= THIS_MODULE,
+	.flags          = 0,
+	.verify		= s3c64xx_cpufreq_verify_speed,
+	.target		= s3c64xx_cpufreq_set_target,
+	.get		= s3c64xx_cpufreq_get_speed,
+	.init		= s3c64xx_cpufreq_driver_init,
+	.name		= "s3c",
+};
+
+static int __init s3c64xx_cpufreq_init(void)
+{
+	return cpufreq_register_driver(&s3c64xx_cpufreq_driver);
+}
+module_init(s3c64xx_cpufreq_init);

drivers/mmc/host/s3cmci.c

@@ -794,7 +794,7 @@ static void s3cmci_dma_setup(struct s3cmci_host *host,
 			      host->mem->start + host->sdidata);
 
 	if (!setup_ok) {
-		s3c2410_dma_config(host->dma, 4, 0);
+		s3c2410_dma_config(host->dma, 4);
 		s3c2410_dma_set_buffdone_fn(host->dma,
 					    s3cmci_dma_done_callback);
 		s3c2410_dma_setflags(host->dma, S3C2410_DMAF_AUTOSTART);