arm64: dts: qcom: sdm845: Add second PCIe PHY and controller

Add the second PCIe controller and the associated QHP PHY found on
SDM845.
Tested-by: Julien Massot <jmassot@softbankrobotics.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191107002247.1127689-3-bjorn.andersson@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arch/arm64/boot/dts/qcom/sdm845.dtsi

@@ -1468,6 +1468,114 @@ pcie0_lane: lanes@1c06200 {
 			};
 		};
 
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sdm845", "snps,dw-pcie";
+			reg = <0 0x01c08000 0 0x2000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ref",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1c00 0xf>;
+			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
+				    <0x100 &apps_smmu 0x1c01 0x1>,
+				    <0x200 &apps_smmu 0x1c02 0x1>,
+				    <0x300 &apps_smmu 0x1c03 0x1>,
+				    <0x400 &apps_smmu 0x1c04 0x1>,
+				    <0x500 &apps_smmu 0x1c05 0x1>,
+				    <0x600 &apps_smmu 0x1c06 0x1>,
+				    <0x700 &apps_smmu 0x1c07 0x1>,
+				    <0x800 &apps_smmu 0x1c08 0x1>,
+				    <0x900 &apps_smmu 0x1c09 0x1>,
+				    <0xa00 &apps_smmu 0x1c0a 0x1>,
+				    <0xb00 &apps_smmu 0x1c0b 0x1>,
+				    <0xc00 &apps_smmu 0x1c0c 0x1>,
+				    <0xd00 &apps_smmu 0x1c0d 0x1>,
+				    <0xe00 &apps_smmu 0x1c0e 0x1>,
+				    <0xf00 &apps_smmu 0x1c0f 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0a000 {
+			compatible = "qcom,sdm845-qhp-pcie-phy";
+			reg = <0 0x01c0a000 0 0x800>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
+				 <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: lanes@1c06200 {
+				reg = <0 0x01c0a800 0 0x800>,
+				      <0 0x01c0a800 0 0x800>,
+				      <0 0x01c0b800 0 0x400>;
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				clock-output-names = "pcie_1_pipe_clk";
+			};
+		};
+
 		ufs_mem_hc: ufshc@1d84000 {
 			compatible = "qcom,sdm845-ufshc", "qcom,ufshc",
 				     "jedec,ufs-2.0";