Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  staging: iio: max517: Fix iio_info changes
  Staging: mei: fix debug code
  Staging: cx23885: fix include of altera.h
  staging: iio: error case memory leak fix
  staging: ath6kl: Fix a kernel panic during suspend/resume
  staging: gma500: get control from firmware framebuffer if conflicts
  staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
  staging: usbip: bugfix prevent driver unbind
  staging: iio: industrialio-trigger: set iio_poll_func private_data
  staging: rts_pstor: use bitwise operator instead of logical one
  staging: fix ath6kl build when CFG80211 is not enabled
  staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
  staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
  Staging: remove STAGING_EXCLUDE_BUILD option
  Staging: altera: move .h file to proper place

drivers/media/video/cx23885/cx23885-cards.c

@@ -25,8 +25,8 @@
 #include <linux/delay.h>
 #include <media/cx25840.h>
 #include <linux/firmware.h>
-#include <staging/altera.h>
 
+#include "../../../staging/altera-stapl/altera.h"
 #include "cx23885.h"
 #include "tuner-xc2028.h"
 #include "netup-init.h"

drivers/staging/Kconfig

@@ -24,23 +24,6 @@ menuconfig STAGING
 
 if STAGING
 
-config STAGING_EXCLUDE_BUILD
-	bool "Exclude Staging drivers from being built" if STAGING
-	default y
-	---help---
-	  Are you sure you really want to build the staging drivers?
-	  They taint your kernel, don't live up to the normal Linux
-	  kernel quality standards, are a bit crufty around the edges,
-	  and might go off and kick your dog when you aren't paying
-	  attention.
-
-	  Say N here to be able to select and build the Staging drivers.
-	  This option is primarily here to prevent them from being built
-	  when selecting 'make allyesconfg' and 'make allmodconfig' so
-	  don't be all that put off, your dog will be just fine.
-
-if !STAGING_EXCLUDE_BUILD
-
 source "drivers/staging/tty/Kconfig"
 
 source "drivers/staging/generic_serial/Kconfig"
@@ -177,5 +160,4 @@ source "drivers/staging/mei/Kconfig"
 
 source "drivers/staging/nvec/Kconfig"
 
-endif # !STAGING_EXCLUDE_BUILD
 endif # STAGING

drivers/staging/altera-stapl/altera-jtag.c

@@ -26,7 +26,7 @@
 #include <linux/delay.h>
 #include <linux/firmware.h>
 #include <linux/slab.h>
-#include <staging/altera.h>
+#include "altera.h"
 #include "altera-exprt.h"
 #include "altera-jtag.h"
 

drivers/staging/altera-stapl/altera.c

@@ -28,7 +28,7 @@
 #include <linux/string.h>
 #include <linux/firmware.h>
 #include <linux/slab.h>
-#include <staging/altera.h>
+#include "altera.h"
 #include "altera-exprt.h"
 #include "altera-jtag.h"
 

drivers/staging/ath6kl/Kconfig

 config ATH6K_LEGACY
 	tristate "Atheros AR6003 support (non mac80211)"
         depends on MMC && WLAN
+	depends on CFG80211
         select WIRELESS_EXT
         select WEXT_PRIV
 	help

drivers/staging/ath6kl/os/linux/cfg80211.c

@@ -870,7 +870,8 @@ ar6k_cfg80211_scanComplete_event(struct ar6_softc *ar, int status)
     if(ar->scan_request)
     {
         /* Translate data to cfg80211 mgmt format */
-        wmi_iterate_nodes(ar->arWmi, ar6k_cfg80211_scan_node, ar->wdev->wiphy);
+	if (ar->arWmi)
+		wmi_iterate_nodes(ar->arWmi, ar6k_cfg80211_scan_node, ar->wdev->wiphy);
 
         cfg80211_scan_done(ar->scan_request,
             ((status & A_ECANCELED) || (status & A_EBUSY)) ? true : false);

drivers/staging/brcm80211/brcmfmac/wl_iw.c

@@ -64,8 +64,6 @@ wl_iw_extra_params_t g_wl_iw_params;
 extern bool wl_iw_conn_status_str(u32 event_type, u32 status,
 				  u32 reason, char *stringBuf, uint buflen);
 
-uint wl_msg_level = WL_ERROR_VAL;
-
 #define MAX_WLIW_IOCTL_LEN 1024
 
 #ifdef CONFIG_WIRELESS_EXT

drivers/staging/gma500/psb_drv.c

@@ -542,6 +542,8 @@ static int psb_driver_load(struct drm_device *dev, unsigned long chipset)
 	unsigned long irqflags;
 	int ret = -ENOMEM;
 	uint32_t tt_pages;
+	struct drm_connector *connector;
+	struct psb_intel_output *psb_intel_output;
 
 	dev_priv = kzalloc(sizeof(*dev_priv), GFP_KERNEL);
 	if (dev_priv == NULL)
@@ -663,7 +665,18 @@ static int psb_driver_load(struct drm_device *dev, unsigned long chipset)
 		drm_kms_helper_poll_init(dev);
 	}
 
-	ret = psb_backlight_init(dev);
+	/* Only add backlight support if we have LVDS output */
+	list_for_each_entry(connector, &dev->mode_config.connector_list,
+			    head) {
+		psb_intel_output = to_psb_intel_output(connector);
+
+		switch (psb_intel_output->type) {
+		case INTEL_OUTPUT_LVDS:
+			ret = psb_backlight_init(dev);
+			break;
+		}
+	}
+
 	if (ret)
 		return ret;
 #if 0

drivers/staging/gma500/psb_fb.c

@@ -441,6 +441,16 @@ static int psbfb_create(struct psb_fbdev *fbdev,
 	info->screen_size = size;
 	memset(info->screen_base, 0, size);
 
+	if (dev_priv->pg->stolen_size) {
+		info->apertures = alloc_apertures(1);
+		if (!info->apertures) {
+			ret = -ENOMEM;
+			goto out_err0;
+		}
+		info->apertures->ranges[0].base = dev->mode_config.fb_base;
+		info->apertures->ranges[0].size = dev_priv->pg->stolen_size;
+	}
+
 	drm_fb_helper_fill_fix(info, fb->pitch, fb->depth);
 	drm_fb_helper_fill_var(info, &fbdev->psb_fb_helper,
 				sizes->fb_width, sizes->fb_height);

drivers/staging/gma500/psb_intel_bios.c

@@ -154,10 +154,15 @@ static void parse_lfp_panel_data(struct drm_psb_private *dev_priv,
 
 	fill_detail_timing_data(panel_fixed_mode, dvo_timing);
 
-	dev_priv->lfp_lvds_vbt_mode = panel_fixed_mode;
-
-	DRM_DEBUG("Found panel mode in BIOS VBT tables:\n");
-	drm_mode_debug_printmodeline(panel_fixed_mode);
+	if (panel_fixed_mode->htotal > 0 && panel_fixed_mode->vtotal > 0) {
+		dev_priv->lfp_lvds_vbt_mode = panel_fixed_mode;
+		DRM_DEBUG("Found panel mode in BIOS VBT tables:\n");
+		drm_mode_debug_printmodeline(panel_fixed_mode);
+	} else {
+		DRM_DEBUG("Ignoring bogus LVDS VBT mode.\n");
+		dev_priv->lvds_vbt = 0;
+		kfree(panel_fixed_mode);
+	}
 
 	return;
 }

drivers/staging/iio/dac/max517.c

@@ -195,7 +195,7 @@ static const struct iio_info max517_info = {
 };
 
 static const struct iio_info max518_info = {
-	.attrs = &max517_attribute_group,
+	.attrs = &max518_attribute_group,
 	.driver_module = THIS_MODULE,
 };
 

drivers/staging/iio/imu/adis16400_ring.c

@@ -137,13 +137,13 @@ static irqreturn_t adis16400_trigger_handler(int irq, void *p)
 		if (st->variant->flags & ADIS16400_NO_BURST) {
 			ret = adis16350_spi_read_all(&indio_dev->dev, st->rx);
 			if (ret < 0)
-				return ret;
+				goto err;
 			for (; i < ring->scan_count; i++)
 				data[i]	= *(s16 *)(st->rx + i*2);
 		} else {
 			ret = adis16400_spi_read_burst(&indio_dev->dev, st->rx);
 			if (ret < 0)
-				return ret;
+				goto err;
 			for (; i < indio_dev->ring->scan_count; i++) {
 				j = __ffs(mask);
 				mask &= ~(1 << j);
@@ -158,9 +158,13 @@ static irqreturn_t adis16400_trigger_handler(int irq, void *p)
 	ring->access->store_to(indio_dev->ring, (u8 *) data, pf->timestamp);
 
 	iio_trigger_notify_done(indio_dev->trig);
-	kfree(data);
 
+	kfree(data);
 	return IRQ_HANDLED;
+
+err:
+	kfree(data);
+	return ret;
 }
 
 void adis16400_unconfigure_ring(struct iio_dev *indio_dev)

drivers/staging/iio/industrialio-trigger.c

@@ -294,6 +294,7 @@ struct iio_poll_func
 	pf->h = h;
 	pf->thread = thread;
 	pf->type = type;
+	pf->private_data = private;
 
 	return pf;
 }

drivers/staging/mei/init.c

@@ -205,10 +205,10 @@ int mei_hw_init(struct mei_device *dev)
 			"host_hw_state = 0x%08x, me_hw_state = 0x%08x.\n",
 			dev->host_hw_state, dev->me_hw_state);
 
-		if (!(dev->host_hw_state & H_RDY) != H_RDY)
+		if (!(dev->host_hw_state & H_RDY))
 			dev_dbg(&dev->pdev->dev, "host turn off H_RDY.\n");
 
-		if (!(dev->me_hw_state & ME_RDY_HRA) != ME_RDY_HRA)
+		if (!(dev->me_hw_state & ME_RDY_HRA))
 			dev_dbg(&dev->pdev->dev, "ME turn off ME_RDY.\n");
 
 		printk(KERN_ERR "mei: link layer initialization failed.\n");

drivers/staging/olpc_dcon/Kconfig

@@ -2,6 +2,7 @@ config FB_OLPC_DCON
 	tristate "One Laptop Per Child Display CONtroller support"
 	depends on OLPC && FB
 	select I2C
+	select BACKLIGHT_CLASS_DEVICE
 	---help---
 	  Add support for the OLPC XO DCON controller.  This controller is
 	  only available on OLPC platforms.   Unless you have one of these

drivers/staging/rts_pstor/sd.c

@@ -2328,7 +2328,7 @@ static int reset_sd(struct rtsx_chip *chip)
 
 			retval = sd_send_cmd_get_rsp(chip, IO_SEND_OP_COND, 0, SD_RSP_TYPE_R4, rsp, 5);
 			if (retval == STATUS_SUCCESS) {
-				int func_num = (rsp[1] >> 4) && 0x07;
+				int func_num = (rsp[1] >> 4) & 0x07;
 				if (func_num) {
 					RTSX_DEBUGP("SD_IO card (Function number: %d)!\n", func_num);
 					chip->sd_io = 1;

drivers/staging/usbip/stub_dev.c

@@ -26,6 +26,8 @@
 static int stub_probe(struct usb_interface *interface,
 		      const struct usb_device_id *id);
 static void stub_disconnect(struct usb_interface *interface);
+static int stub_pre_reset(struct usb_interface *interface);
+static int stub_post_reset(struct usb_interface *interface);
 
 /*
  * Define device IDs here if you want to explicitly limit exportable devices.
@@ -59,6 +61,8 @@ struct usb_driver stub_driver = {
 	.probe		= stub_probe,
 	.disconnect	= stub_disconnect,
 	.id_table	= stub_table,
+	.pre_reset	= stub_pre_reset,
+	.post_reset	= stub_post_reset,
 };
 
 /*
@@ -541,3 +545,20 @@ static void stub_disconnect(struct usb_interface *interface)
 		del_match_busid((char *)udev_busid);
 	}
 }
+
+/* 
+ * Presence of pre_reset and post_reset prevents the driver from being unbound
+ * when the device is being reset
+ */
+ 
+int stub_pre_reset(struct usb_interface *interface)
+{
+	dev_dbg(&interface->dev, "pre_reset\n");
+	return 0;
+}
+
+int stub_post_reset(struct usb_interface *interface)
+{
+	dev_dbg(&interface->dev, "post_reset\n");
+	return 0;
+}

drivers/staging/usbip/stub_rx.c

@@ -175,16 +175,18 @@ static int tweak_reset_device_cmd(struct urb *urb)
 	dev_info(&urb->dev->dev, "usb_queue_reset_device\n");
 
 	/*
-	 * usb_lock_device_for_reset caused a deadlock: it causes the driver
-	 * to unbind. In the shutdown the rx thread is signalled to shut down
-	 * but this thread is pending in the usb_lock_device_for_reset.
-	 *
-	 * Instead queue the reset.
-	 *
-	 * Unfortunatly an existing usbip connection will be dropped due to
-	 * driver unbinding.
+	 * With the implementation of pre_reset and post_reset the driver no 
+	 * longer unbinds. This allows the use of synchronous reset.
 	 */
-	usb_queue_reset_device(sdev->interface);
+
+	if (usb_lock_device_for_reset(sdev->udev, sdev->interface)<0)
+	{
+		dev_err(&urb->dev->dev, "could not obtain lock to reset device\n");
+		return 0;
+	}
+	usb_reset_device(sdev->udev);
+	usb_unlock_device(sdev->udev);
+
 	return 0;
 }